Search Documents

By Italo Oñederra

A review of breakage and fragmentation literature has shown that only a few models have been specifically developed for applications in underground production blasting. These approaches, however, have applied empirical relations that do not adequately consider ring blasting geometries, have failed to appropriately respond to changes in basic design input parameters, and have complex input and calibration requirements. This justified the development of an alternative modelling framework to specifically address the prediction of fragmentation in underground production blasting. In this sense, the new model, designated as “FRAGMENTO”, is introduced in this paper. The basis of FRAGMENTO is a “single ring” deterministic model which can be extended into a stochastic model to simulate the impact of external operational factors on fragmentation. The single-ring component mechanistically models the extent of both near field and mid to far field fracture zones to predict the distribution of rock fragments expected to report to drawpoints. In this paper the response of this key component is evaluated and its practical application demonstrated with the introduction of a methodology to infer critical burden conditions.

Sep 12, 2005

By Y X. Xue, J Pan, D Q. Zhu

In order to reveal the correlation between the fundamental sintering characteristics of iron ores and their real sintering behaviours, a comprehensive evaluation index is proposed based on the measurement of four high temperature indexes, ie assimilation temperature, liquid phase bonding strength, liquid fluidity and calcium ferrite formation percentage, and the sintering pot tests of single ore fines and their blends. The results show that both the lowest assimilation temperature and liquid fluidity of ore blends appear to be the linear superposition of those of single iron ores except for the liquid phase bonding strength and calcium ferrite formation percentage. Furthermore, the tumble index of the sinter product obtained from blended iron ores also corresponds to a linear superposition of that of single ores, but not for the solid fuel rate and productivity. The comprehensive strength index YT exhibits a credible linear positive correlation with the four high temperature reactivity indexes, whereas the comprehensive productivity index YP possesses a lower correlation with the four high temperature reactivity indexes. The comprehensive strength index YT developed can predict the tumble index of the sinter product quite well, but the comprehensive productivity index YP cannot be used to evaluate the productivity effectively.CITATION:Zhu, D Q, Xue, Y X, Pan, J and Shi, B J, 2017. Correlation between high temperature sintering characteristics and sintering behaviours of iron ore fines, in Proceedings Iron Ore 2017, pp 123–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

The conventional rare earth element (REE) industry has historically sought to develop ore deposits where geologic processes have produced mineralized zones with commercially attractive REE concentrations. These deposits are extremely uncommon, particularly in the USA. Given the criticality of these materials and the need for sustainable domestic supply, the current research seeks to leverage other autogenous processes that lead to concentrated REE resources. One such process is the generation of acid mine drainage (AMD). AMD is very common in many coal mining districts and results from the exposure and oxidation of pyrite during mining. During the generation and migration of AMD, liberated sulfuric acid mobilizes several metal ions including REEs. Treatment of AMD is required under U.S.C §1251, the Clean Water Act, and often consists of neutralization, oxidation, and metal hydroxide precipitation. To investigate the deportment of REEs during this process, a field sampling campaign was undertaken, whereby the concentration of REEs in AMD and AMD precipitates was measured directly. In the nine sites evaluated in this study, the REE concentrations of the precipitates varied from 29 to 1286 ppm with an average of 517 ppm among the sampled sites. The individual elements were enriched compared with the associated bulk Northern Appalachian (NAPP) coal material by factors ranging from 3 to 15. Furthermore, the distribution of REEs in all precipitate samples favored the heavy REEs (HREEs) when compared with traditional REE ores. This research represents the first part of multi-part research endeavor to characterize, classify, and determine the practicality of refining REEs from AMD and its by-products.

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

The conventional rare earth element (REE) industry has historically sought to develop ore deposits where geologic processes have produced mineralized zones with commercially attractive REE concentrations. These deposits are extremely uncommon, particularly in the USA. Given the criticality of these materials and the need for sustainable domestic supply, the current research seeks to leverage other autogenous processes that lead to concentrated REE resources. One such process is the generation of acid mine drainage (AMD). AMD is very common in many coal mining districts and results from the exposure and oxidation of pyrite during mining. During the generation and migration of AMD, liberated sulfuric acid mobilizes several metal ions including REEs. Treatment of AMD is required under U.S.C §1251, the Clean Water Act, and often consists of neutralization, oxidation, and metal hydroxide precipitation. To investigate the deportment of REEs during this process, a field sampling campaign was undertaken, whereby the concentration of REEs in AMD and AMD precipitates was measured directly. In the nine sites evaluated in this study, the REE concentrations of the precipitates varied from 29 to 1286 ppm with an average of 517 ppm among the sampled sites. The individual elements were enriched compared with the associated bulk Northern Appalachian (NAPP) coal material by factors ranging from 3 to 15. Furthermore, the distribution of REEs in all precipitate samples favored the heavy REEs (HREEs) when compared with traditional REE ores. This research represents the first part of multi-part research endeavor to characterize, classify, and determine the practicality of refining REEs from AMD and its by-products.

By Gerald G. Johnson

The use of the Scanning Electron Microscope to characterize Coal Mine Dust has been possible because of two circumstances. First, the imaging process of the SEM allows multiple signals (secondary electrons, back scattered electrons, x-ray emission, etc.) to be viewed. Second, the use of a computer to analyze the signals and perform statistical tests on the results. The parameters described are size, shape, chemical composition, mass distributions, and particle thickness. Although the system is intended for particular systems, those of agglomerates (whether tile same or not) are handled by special aspects of the computer programs. The work on fibers is not completed at the time of this report. This work discusses the hardware (developed especially for this process) and software (both on an IBM 360/370 and a PDP 11/20). The latter system allows direct interaction between the operator of the SEM and computer for maximum information at the least time.

Jan 1, 1979

By Belinda Campbell

Tools for Consistency 1. GIS Web Site 2. National Project Management System 3. Site Grouping Approach (721 PIDs) 4. Mine Reclamation Standing Offer Agreements ?Contracting tool 5. Remedial Objectives Guidance Document Background ?CBDC (now ECBC) is a Federal Crown Corporation and falls under federal jurisdiction. ?When it stopped mining coal, CBDC turned its attention to cleaning up and closing out its industrial sites. ?Public Works and Government Services Canada is common service provider to the GoC. ?Expertise in environmental, engineering, IT, project management, communications, GIS, real property management.

May 1, 2011

By R. S. Handy

This paper describing the milling practices at tae concentrators of the Bunker Hill and Sullivan Mining and Concentrating Co. is one of a series being prepared by the United States Bureau of Mines on milling methods and costs in the United States. The possibility of useful comparisons has prompted the description of all five of the mills operated by the Bunker Hill and Sullivan Company in northern Idaho. The general features of these mills are tabulated below: [ ]

Jan 1, 1930

By Carl R. Christiansen

The primary objectives of this project are (1) the determination of manpower demand in primary lead and zinc production for the years 1985 and 2000, and (2) the estimation of the availability of the required manpower for these years. In order to meet the first of these objectives relationships between employee requirements and metal production in the various states were established, The total primary lead and zinc production from United states mines in 1985 and 2000 has been predicted by the U.S. Bureau of Mines. These forecasts and the 1974 figures are as follows: [1974 1985 2000 Lead metal, tons 669,000 700,000 900,000 Zinc metal, tons 494,000 585,000 995,000] Mining By analysis of ore reserve data and industry characteristics, the authors estimated the portion of the primary production which each state would yield in the future years. As manpower requirements are determined by the tons of ore produced and by worker productivity, these figures were determined for each mining state and district by developing relationships between lead and zinc metal production, ore production, ore to recoverable metal ratios, employee productivity, and number of employees required. The number of new employees required annually to compensate for attrition and production growth is provided, also.

Jan 1, 1975

By K. J. G Hedges

"Once a health based guidance limits for exposure to diesel exhaust have been established, and as part of a multi-disciplinary team, the program for exposure reduction should incorporate the plan-do-check-adjust cycle. Setting a suitably protective (health based) occupational exposure limit (OEL) for diesel particulate matter (DPM) and nitrogen dioxide is a key driver to reduce exposure. It is important to go beyond regulations and reduce exposure to diesel exhaust, DPM, as low as reasonably achievable (ALARA) such as that prescribed under the Australia, Queensland Mining and Quarrying Safety and Health Regulation 2017 where under section 135 Limiting workers exposure, the workers exposure must not exceed the exposure limit applying to the worker for the hazard; and is ALARA. It appears that previously acceptable OELs are no longer safe. Therefore it is important that the internal responsibility system be implemented and the precautionary principle approach be followed, especially as it may be some time before a suitably protective OEL specifically for DPM is in place. One leading multi-national mining company BHP Billiton has acknowledged a significant lag that exists between regulatory action and the level of science that informs health risk. This company is managing exposure to diesel exhaust to as low as technically feasible. This same company that has set an interim target for managing diesel exhaust to 0.03 mg/m3 is achieving these levels which paves the way for other mining companies and general industry including construction. The Occupational Cancer Research Centre 2017 recommends reducing personal exposure to within 0.02 mg/m3 (EC) for underground mining and 0.005 mg/m3 for other workplaces. Controlling DPM is important to prevent cancer however it is also important that that nitrogen dioxide (NO2) be reduced (ALARA) and that careful selection of control technology be considered such as the proper selection of a diesel oxidation catalyst so that the level of NO2 does not in fact increase. The example from BHP Billiton provides a leading practice including using a multi-disciplinary approach and the importance of controlling emission at source and having an auditable diesel emissions based monitoring program in place."

Jan 1, 2019

By J. MacFadyen

The U.S. cement industry experienced its best year ever during 2004 in terms of production and shipments of cement. Clinker, portland and masonry cements production and shipments were up considerably. Clinker production as reported to the U.S. Geological Survey (USGS) was 87.75 Mt (96.73 million st), an increase of 5.4 percent. Gray and white portland cement production from domestic and imported clinker was estimated to be 91.6 Mt (101 million st), up 5 Mt (5.5 million st) from 2003.

Jan 1, 2005

By Fulvio Tonon

And Rabcewicz said ?tunnels should be driven full face whenever possible.? ADECO, which stands for ?Analysis of Controlled Deformations in tunnels,? now allows us to fulfll Rabcewicz?s dream in any stress-strain condition. In order to achieve that dream and its consequent control over cost and schedule, however, NATM must be abandoned for the ADECO. The paper presents the basic concepts in the ADECO approach to design, construction and monitoring of tunnels together with some case histories, including: full face excavation for Cassia tunnel (width of 22 m, height of 14 m) in sands and silts under 5 m cover below an archeological area in Rome, Italy; Tartaguille tunnel (face area > 100 m2) advanced full face in highly swelling and squeezing ground under 100 m cover where NATM led to catastrophic failure, France; and 80 km of tunnels (face area > 100 m2) advanced full face in highly squeezing/swelling ground under 500 m cover for the high-speed railway line between Bologne and Florence, Italy (turnkey contract).

By J. Gotor, C. Frias, E. Delgado

The Iberian Pyrite Belt (IPB) is one of the world's largest reserves of primary sulphides containing base metals (Cu, Zn, Pb), precious metals and some special metals such as indium. Estimated resources are over 1,500 million tonnes of volcanogenic massive sulphide ores. From 1980´s Europe lives the decline in its mines mainly motivated by the low price of the metals. One aspect that contributed equally to this was the ecological disaster produced by the discharge of more than seven million tonnes from the tailings dam of Boliden-Apirsa (Aznalcollar) in 1998. Today the situation is different; the companies present in the IPB have given evidence that it is possible to reconcile mining projects and care on the environment, and the regional authorities are opening a public tender to re-start Aznalcollar mine. A new challenging era has been started at this Spanish/Portuguese mining area. This paper presents the results and preliminary economics of a project devoted to IPB primary sulphides processing through different technology approach, e.g. conventional selective flotation against bulk flotation or mixed metals flotation combined with hydrometallurgical processing.

Jan 1, 2014

Tailings management trade-off studies are done for all mining projects. There is wide variability in these studies as their approach, details and outcomes are determined by the experience and focus of the project team. While some of these approaches may consider the whole life cycle of the project others may focus only on capital and operating costs and direct environmental impacts. A complete life cycle approach is not standard practice. This paper describes an approach to implementation of formalised life cycle assessment (LCA) following ISO 14044 to tailings management trade-off studies. The paper describes the implementation of the methodological framework for the LCA, ie goal and scope definition, life cycle inventory analysis, life cycle impact assessment and life cycle interpretation. This standardised approach to implementing tailings management trade-off studies following the LCA approach will contribute to the state-of-the-practice in sustainable mine development.

Jan 1, 2009

By Reda M. Bakeer

"Measurements obtained during load testing of two steel H-piles driven at a site in Northeastern Mississippi are discussed. The general site conditions, equipment used, testing procedures and results of the pile load tests are presented. Both piles were tested in compression and one of the piles was subsequently tested in tension. The piles were instrumented with strain gauges and extensometers to measure the mobilized soil resistance and pile movement. Three different “zero strain” conditions were used to determine the mobilized soil resistance and residual loads due to driving or a load cycle. It was concluded that the effect of residual loads on driven piles could be significant. Driving residual loads influenced the magnitude and distribution of the load transfer curves more than those due to a load cycle. Results of the tension test were impacted by the residual loads from the previous compression test performed on the same pile.INTRODUCTIONSeveral factors affect the performance of a deep foundation system including the subsoil conditions, loading settings, pile type and installation method. Residual stresses develop in piles particularly due to pile driving, but they are typically not accounted for in the analysis (Fellenius 2002). Siegel and McGillivray (2009) presented an assessment of residual loads measured during load testing of instrumented auger-cast-in-place (ACIP) piles. The magnitude and distribution of residual stresses along the pile shaft and toe depend on the pile installation method, previous load cycles and time effects. Poulos (1987) reported that residual load due to driving at the pile toe is independent of pile driving equipment and may significantly affect the results of a pile load test. Hunter and Davisson (1969) reported results of pile load tests performed in compression on fully instrumented piles driven in cohesionless soils along with a discussion of the effects of residual loads. Tension loads of about 445 kN (100 kips) were measured at the pile toe after driving. Unloading residual compression load at the toe was detected as “apparent” tension since the instrumentation was zeroed prior to the test. The researchers suggested a graphical approach to obtain the “corrected” load distribution curves considering that residual load will dissipate following the tension test. Holloway et al. (1975) conducted a study on the effect of residual stresses due to pile driving and developed a computer software that accounts for residual loads. Briaud and Tucker (1984) suggested a method to account for residual loads based on the results of 33 pile load tests performed in mostly cohesionless soils."

Jan 1, 2017

By G. L. Liu

"Deformation Banding ( DB ) in cold rolled mild steel has been experimentally established by microstructure investigation. Deformation banding model includes such deformation mode when it is applied to rolling texture simulation. The cause for the occurrence of deformation banding is the reduction of the total work for plastic deformation through a relaxation of the deformation constraints. In the first DB model, all grains are assumed to band from the first deformation step. Such an unrealistic assumption has been eliminated in the new model by the introduction of a banding criterion based on an energy minimizing approach. The prediction is closer to the measured texture by applying banding criterion and setting critical resolved shear stresses (CRSS) ratio for { 110 } and { 112 } slip modes to 0.85.IntroductionBased on the continuum theory of plastic flow and deformation mechanism of crystallographic dislocation slip, Taylor's FC ( Full Constrain ) theory [1] has been widely used in texture modeling. As the process of cold rolling of sheet materials produces a microstructure consisting of elongated or equiaxed flat grain or cell, the ""lath"" and ""pancake"" relaxed constraints ( RC ) models [2, 3] were introduced as the successful improvements over the classical FC model. It has been also recognized that crystals may split into different orientations during deformation and the term deformation banding is used to describe such deformation processes [4, 5]. Lee et al. [6, 7] pointed out that the success of the RC theory in predicting textures depends on the physical processes of deformation banding. They developed so called Deformation Banding ( DB ) model by considering DB in the longitudinal plane to be accounted for by the RC method and allowing DB in the rolling plane. DB model was applied to simulate the texture development in bee case [8], the predicted bee rolling textures are in reasonable agreement with the measured textures. In the first DB model, however, all grains are assumed to band right upon the first deformation step. A banding criterion was formulated [7] which states that DB will occur if the work used in DB model is less than that in RC model. Such criterion has been incorporated into the original DB model for texture simulation and is referred to as DBC ( Deformation Banding Criterion ) model."

Jan 1, 1998

By P. M. Lin

A subsidence monitoring program over a longwall panel was established (1) to explore the impacts of dynamic subsidence on the ground surface and structures and (2) to correlate the movements between the structures and their corresponding points on the ground. The program consisted of a transverse line survey and a series of survey points around the structures on the ground surface and their corresponding survey points on the exterior walls of the structures. The vertical displacement of each point can be expressed as: where Si is subsidence at i point; Sif is the final subsidence at i point; F is face location in terms of distance from the i point and SD is seam depth. The development of subsidence can be divided into five stages. Damage to the structures starts at the beginning of the second stage, The maximum damage developed in the middle of the third stage. The relationship of the vertical displacement between ground surface and structures can be expressed as: G = aH + b where G is ground displacement, H is structures displacement, and a and b are constants. The relationship is linear. However, the strain is non-linear and more complicated because of the interaction of the ground surface and structure.

Jan 1, 1989

By Terry L. Muldoon

This report describes development and demonstration of an upgraded stench fire warning system for underground wines. Current systems, which have been used since before 1920, release an ethyl mercaptan mixture into the mines' compressed and/or ventilation air during emergencies. Miners, when smelling ethyl mercaptan, evacuate the mine according to predetermined plans. These systems, while simple, have problems with safety and reliability. The upgraded system overcomes these problems. The system uses a different stench agent, is less toxic, less nauseating, and less corrosive than ethyl mercaptan. These combined with the feature of thiophane not reacting with iron oxides, makes the upgraded system safer and more reliable. The system also uses a combination of two simple principles: a standpipe with pressure balancing to provide a constant head, and a sized orifice to control the rate of release of the stench agent. This system enables the mine to release the agent for a longer period which provides better coverage and to ensure that miners will not be exposed to potentially toxic concentrations of the stench agent. The system is easy to operate, requiring only the turning of two 1/4-turn ball valves. The upgraded system has been successfully tested during two evacuation drills at an underground uranium mine. Using three injectors (one on the compressed air line and one on each of two intake air shafts), the system exhibited significant improvements in warning times over the mine's existing system. This report provides a detailed description of the system design and its demonstrated performance in two mine demonstrations.

Jan 1, 1981

Even though the economy of the United States remains in recession ? or not, depending on which economist you listen to ? muicipalities still need improved transportation, water and wastewater transit systems. And they are willing to spend the necessary funds on those systems, provided they are affordable, environ-mentally friendly and sustainable. From June 20-23, professionals in the tunneling and underground construction industry from around the world gathered in Portland, OR to learn new ways of providing those systems using the latest technology available. The North American Tunneling (NAT) conference attracted 803 attendees and 108 exhibiting suppliers of equipment and services.

Jan 1, 2010

The C.S.A. copper-lead-zinc mine, located 7 miles north of Cobar in central-western New South Wales, is the largest known mineral ocurrence in the Cobar mining field. The generally discordant orebodies occur within a strike width of 600 ft and an overall strike length of 1200 ft. They are enclosed by the steeply westdipping, west-facing sediments of the Cobar Group, and comprise lenticular steeply north-pitching and eastdipping zones of sulphide mineralization which range in composition from massive pyrite-sphalerite-pyrrhotitegalena to less massive pyrite-pyrrhotite-chalcopyrite varieties.The thinly bedded siltstones, shales, and greywackes enclosing the mineralization appear to have derived some of their constituents from volcanic sources. They have been metamorphosed to the greenschist facies of regional metamorphism. At least two stages of deformation and folding have occurred. The first stage folded the rocks on a south pitching fold axis into their present configuration, and superimposed a strong axial plane cleavage which subsequently guided the emplacement of the mineralization. The second stage of deformation is considered to have controlled the zonal distribution of the orebodies.

Jan 1, 1970

By Carroll Forbes

INTRODUCTION MANY different shapes of drill bits are in use with hammer drills, but little definite information is available whereby to judge which one of these shapes is the best. The following investigation was undertaken in order to determine what effect, if any, the shape of the cutting edge has on the cutting speed and wearing qualities of drill bits. The bits tested were those in common use, namely, the 4-point or cross bit, the 6-point bit, the Z bit and the "Carr" bit. The rock in which the tests were made was the red granite from southeast Missouri. It is a coarse crystalline granite containing an unusually large amount of quartz and is extremely hard, and on account of its uniform texture is admirably adapted to this work. While tests in other rocks might show somewhat different results, nevertheless it is the opinion of the authors that the relative cutting quality inherent in the shape of the bits would be the same in all rocks. Other qualities, such as mudding freely, freedom from fitchering, etc., might make one bit more desirable than another in softer rocks. DESCRIPTION OF BITS TESTED The 4-point bits were the usual shaped bits commonly made on the Leyner sharpener with 14° taper on the wings and a 90° angle between cutting edges. Some tests were run at 85 lb. pressure with a 4-point bit made with a 5° taper on the wings. This was made by using the Carr bit die. The 6-point bits were the usual shaped hits made on, the Leyner sharpener. The Carr bits were made with a 5° taper and an angle of 100° between cutting edges.

Jan 8, 1917