Search Documents

By M. D. Carver

The purpose of this investigation was to determine the effects of variations in content (near the residual level) of the impurities aluminum, nitrogen, manganese, and copper on the corrosion rate in pressurized hot water and in pressurized steam of zircaloy-3, a zirconium-base alloy of 0.25 percent tin and 0.25 percent iron. Thirty-five 10-pound ingots were cast with the appropriate additions of impurity elements, and these were converted to wrought sheets. These specimens were then tested both in water and in steam. The analysis of the resulting data showed that in environments of either pressurized hot water or superheated steam, corrosion rates increased with increasing content of aluminum, nitrogen, or manganese, but were not affected by variations of copper. The effects of aluminum and nitrogen were found to be greater than the effect of manganese. INTRODUCTION At the request of the Atomic Energy Commission (AEC) in August 1956, the Federal Bureau of Mines, in cooperation with Bettis Plant of Westinghouse Electric Corp., began investigating the effects of certain impurity elements on the corrosion rates of zircaloy-3 in pressurized hot water and in pressurized steam. It was necessary to know these effects in order to set control limits on residual impurity levels in zirnaloy-3, intended for heat transfer service in the nuclear reactor of the pressurized water type. A factorial expert it was designed by Westinghouse statisticians. The Atomic Energy Commission provided raw zirconium sponge purchased from Wah Chang Corp. The Bureau's laboratory at Albany, Oreg., made material of different combinations of impurity levels and subjected the material to corrosion tests. This report will describe the work done at the Bureau laboratory and will show, quantitatively the effects of different residual levels of aluminum or nitrogen, or manganese or copper on corrosion rates.

Jan 1, 1961

By B Cook, M Karakus, J Light, E K. Chanda

The aim of this research is to develop a model through which the appropriate paste recipe parameters, for example solid content and cement content, can be derived given the stope specific requirements such as stope dimensions, required strength and curing time. A large number of samples and uniaxial compressive strength (UCS) tests were conducted at the Angas Zinc Mine (AZM) paste plant and testing facility. Samples were varied in tailings solids content, cement content and sand content. The results of this testing were modelled to determine the UCS relationship to each of the parameters. The output of this modelling was an easy-to-use program that outputs the design mixture given the stope dimensions and required stope backfill-curing time. This allowed flexibility within the mining schedule for curing times of cemented paste backfill stopes. The optimised schedule using the stope specific mix design, when compared to the standard 14-day curing time used previously, resulted in a smoother weekly mine production schedule. For the modelled 12-week period (one quarter) the 14-day curing time would result in an eight-day shutdown of the mill. The cost for each shutdown is in the order of $125 000/d. Due to the unique nature of each mine’s tailings, this exact outcome would not be directly applicable to another paste fill site. However, the process in this report could be followed for another site to achieve a system similar to the output of this project. This would ultimately lead to a more optimised backfill and stoping cycle and a more optimised mine.CITATION:Chanda, E K, Karakus, M, Light, J, Cook, B and Harris, A, 2014. Optimisation of the paste fill cycle at Angas Zinc Mine, Strathalbyn, South Australia, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 259–264 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Kampe. S. L., Baker. Andrew H., Tony Zahrah

"Experimental heats of reaction for the formation of several Al3Ti + TiB2 intermetallic composite formulations have been determined utilizing bomb calorimetry. To overcome the kinetic constraints and achieve ignition in these formulations, a boron (B)/potassium nitrate (KNO3) initiation aid was incorporated within the blended reactant compact. The heat contribution from the initiation aid was regressed to provide estimates of the heat of reaction of the nominal formulations. Powder x-ray diffraction was utilized to identify the products of the reaction and discern any differences between the predicted equilibrium products of the formulation and the actual products.IntroductionReaction synthesis is a technique for the creation of ceramics, intermetallics, and in-situ composite materials [1]. Reaction synthesis is defined by its self, propagating mechanism, where the energy liberated from a localized reaction within a green powder compact is enough to carry the bulk reaction to completion. Achieving a self, propagating state can be achieved in variations of two primary methods of initiation: uniform volumetric heating and directional propagation [2].Uniform volumetric heating involves subjecting a green compact of the unreacted formulation to uniform heating in a furnace to encourage diffusion to initiate the reaction (Figure 1a) throughout the bulk material. Directional propagation utilizes a point heat source at one section of a green compact of unreacted formulation (Figure 1b). The localized exothermic reaction at one point in the compact then initiates the reaction in the section of the compact adjacent to it and fully propagates throughout the entire compact until completion. Initiation of the localized reaction is generally associated with the melting of the constituent with the lowest melting point, with instantaneous initiation of the reaction usually occurring close to that melting point [1]. This melting point can be high in some systems of interest, such as the titanium (Ti) and boron (B) system in equation 1:"

Jan 1, 2011

The introduction and subsequent ascendancy of autogenous and semi-autogenous milling for comminution circuits has undoubtedly lead to many economic advantages. From a process viewpoint, however, at least one downside has been the sensitivity of these machines to process input variations. Foremost among these is ore competence, though feed size comes a close second. This sensitivity is due to the reliance of ag/sag mills on the feed ore for their grinding media competence and size. Autogenous (ag) mills are the most sensitive in this respect with semi-autogenous (sag) mills being increasingly less so as the ball charge is increased. Increasingly designers and operators are recognising the importance of feed size and the benefits of manipulating it to improve performance. This has been achieved by installing additional crushing/screening capacity ahead of the ag/sag, better operation of the primary crusher, better control of segregation cased by stockpiles and bins and by changing blast design/practices to modify the ROM size distribution. This paper describes the influence of feed size distribution on ag/sag mill performance with reference to a range of plant data. It particularly concentrates on how changing blasting practice to modify ag/sag feed size can have a considerable overall benefit.

Jan 1, 2003

By Michael J. Friedel

The permeability and flow capacity in unsaturated media are investigated by the U.S. Bureau of Mines for application to in situ copper leach mining. Moisture retention properties are derived and combined with scanning electron microprobe data to characterize the mineralogy, texture, pore size, distribution, and permeability of the host rock. Finite-element modeling is used to derive a saturated permeability, ambient degree of saturation, and assess various injection-recovery schemes. Recommended design modifications for optimization of solution distribution and maximum recovery from the rock matrix requires either (1) the injection pressures on the order of 1,500 psi and recovery wells operating in a suction mode, or (2) performing permeability enhancement, through in situ rubbling. Injection pressures can be reduced to 500 psi with improved recovery and containment of solutions.

Jan 1, 2010

By Ali Naeimipour

Availability of accurate geological information about the rock mass surrounding a tunnel or mine working is the key to enhance and optimize the required ground support measures. Various approaches have been used to obtain data on ground conditions, including the possibility of characterizing the ground while drilling for roof bolts, by the Measurement While Drilling (MWD) system, via optical, sonic and acoustic televiewers, and using various types of gamma probes. While there are many different systems for characterizing the ground in longer, larger-diameter holes drilled downward, the options for using probes and logging systems in short, small-diameter holes drilled in horizontal or an upward direction are very limited. This paper will present the results of recent field tests using optical televiewer (OPTV) to analyze the joints and voids in boreholes drilled in different directions. The studies show that OPTV is a promising tool; however, getting a good quality image from the upward drill holes still need to be studied. Meanwhile, estimated in-situ strength of the intact rock is needed to complement the jointing pattern for rock mass classification. For this purpose, preliminary steps for the development of a borehole scratcher to estimate rock strength will be discussed in this paper.

Jan 1, 2014

By Robert E. Baker

Cortez Gold Mines, the United States' third largest primary producer of gold, commenced continuous operations on January 10, 1969. The decision to proceed to production was made in March of 1968 and construction of the mill and stripping operations for the pit began in April and July, respectively. Anomalous conditions on the slope of Mt. Tenabo along the Roberts Mountain thrust fault zone were discovered by the U.S.G.S. while conducting geochemical surveys in the old Cortez silver district. Following the discovery of gold an intensive program of drilling was organized. Drilling outlined an orebody with 3.5 million tons of ore averaging 0.28 ounces of gold per ton. It was on the basis of this reserve that a 1700 t. p.d. cyanide plant was designed. Needless to say, with such a limited ore reserve, economies in design and construction would have to be observed. Cortez Gold Mines is a joint venture with American Exploration & Mining Co., The Bunker Hill Company, Vernon F. Taylor, Jr., and Webb Resources, Inc. , as partners. American Exploration & Mining Co. is the operating partner.

Jan 1, 1969

By Ernesto Diez-Canseco Yañez

El siguiente trabajo señala los modos de aprovechamiento del mineral de carbón denominado "andracita", en tanto materia combustible de producción de las briquetas. Es decir, se busca crear un producto biocombustible que mantenga su calidad ecológica y que a su vez genere mayores posiblidades de venta en el mercado internacional, Para ello es necesario, evaluar el nivel de los aglutinantes en su composición y tratar de conservar sus características primigenias de dicho producto.

Jun 20, 1954

By B Mohanty

Currently there exist several explosive quantity-distance (Q-D) rules variously exercised by most countries to protect personnel and property against the effects of accidental explosions. These regulations apply to manufacture, transport and storage of explosive products. This paper reviews the technical basis behind these regulations, as they apply to commercial and military explosives. The characteristics of a blast wave and missiles issuing out of an explosion site and their role in determining the level of damage to a target are discussed. The need for further research on the effect of detonation of charges of non-standard geometry, and under confined conditions such as tunnels is discussed. The challenge in estimating the net quantity of explosives involved and calculation of its TNT-equivalency is also highlighted.

Jan 1, 2014

By Roland Arnold, Richard Gradnik, Martin Zeindl

This paper presents the details of the Kramer tunnel project in the Federal State of Bavaria, Germany. This road tunnel, which has been under construction since December 2019, is the key component of the western bypass of the town of GarmischPartenkirchen. Once completed, it will relieve the town’s central district from enormous volumes of traffic. The contractor is the joint venture named ARGE Kramertunnel consisting of BeMo Tunnelling and Subterra. The whole project will be completed and handed over to the project owner, Staatliches Bauamt Weilheim, in 2023. The opening of the entire bypass section including the tunnel to traffic is planned for 2024. The tunnel, with a total length of 3,609 m (2.24 miles) and an estimated cost of EUR 178 million (incl. VAT), is designed as a single-tube, double-lane structure with one traffic lane for each direction of travel. The safety issue that exists for single-tube tunnels is solved by a parallel escape tunnel passable for vehicles. All tunnels and ducts are excavated according to the principles of the New Austrian Tunnelling Method (NATM). In order to reduce the geological risk for the owner, the escape tunnel was supposed to be completed before the design process for the main tunnel ever began. The exploratory tunnel was awarded to a competitor with an separate contract.

Jun 13, 2021

By John C. Machisak

THIS INFORMATION CIRCULAR covers the calendar year 1055 and contains statistical data on employment and injuries pertinent to metal and nonmetal mining and to their mills and processing plants that are voluntarily reported annually to the Federal Bureau of Mmes. This report, unlike previous publications, lists not only production and development workers but also office employees associated with mining and milling or processing. The last publication m the series, Information Circular 7798, Injury Experience in the Metal and Nonmetal Industries, 1954, also contains unpublished injury and employment statistics for 1943 through 1953. The Bureau is authorized to request data on injuries and employment from operators in the metal- and nonmetal-mining industries. The information voluntarily submitted by these operators contributes immeasurably to the promotion of safety in the mineral mining industries as it discloses the hazards to which metal and nonmetal workers are continually exposed during mineral extractive operations.

Jan 1, 1959

By Mario Gerards, Sergej Podkow, Marco Steinberg

"The JONES® WHIMS technology is based on the magnetic separation process and is widely used for the recovery of magnetically susceptible iron ore particles. The conventional machine design is well-known within the iron ore beneficiation industry for more than 50 years and recognized to be highly reliable, robust and extremely compact with the advantages of high capacity and selectivity. In 1981 Rana Gruber AS, Norway bought 14 JONES® WHIMS DP 317 separators when the magnetic separation plant was built and erected. Today, 11 of these old machines are still operating profitably and efficiently. The former supplier was the coal and minerals division of Klöckner-Humboldt-Deutz (KHD) which is today MBE Coal & Minerals Technology GmbH (MBE). This paper outlines a detailed description of the project of revamping the above mentioned old machines and describes the challenge of incorporating enhanced and newly developed technology into an existing processing plant. Further it gives an overview of the recent developments on the design of the JONES® WHIMS. In order to meet modern product requirements and to increase and secure plant productivity, in 2012 Rana Gruber AS settled a contract covering two new designed JONES® WHIMS DP 317 HFR separators to be implemented into the existing building and the upgrading of all 11 older JONES® WHIMS under the use of as many refurbished items as possible. The two new machines were fully developed by the product specialists of the supplier in cooperation with the operator Rana Gruber AS, thereby taking advantage of their great experience. The design of the new machine is based on the conventional design, i.e. the general operating mode as well as the overall dimensions are identical. Finally this paper gives an overview about the erection and commission phase of the two new machines and gives a detailed comparison between conventional and enhanced WHIMS technology."

Jan 1, 2014

By William P. Shinn

IT seems proper to present in the Transactions of the Institute, from time to time, formal record of the advances made in the arts and sciences to which our organization is devoted-milestones in the highway of progress-from which our successors may measure what they in their turn have gained. The admirable address of the Hon. Abram S. Hewitt, then president elect of the Institute, on "A Century of Mining and Metallurgy in the United States," read at the opening of the meeting held in this hall in June, 1876, forms a point of departure, and the conclusion of the eighth decade of the nineteenth century and the end of the first five years of our country's second century seem to offer a fitting time for again making up our record. The period since 1875 has been marked by a degree of activity in mining and metallurgical industry never before equalled in our history, while the progress made in the science and art has been, if possible, still more noticeable. Whether we consider the mining of iron, ore, and coal, or of the precious metals,-the advances made in smelting the former and in reducing the latter, the extraordinary increase in the production of Bessemer steel, or the science of Thomas and. Gilchrist, which makes the hitherto rejected phosphorus the corner-stone of success,-the past five years are alike memorable for the progress they have shown and to some of the most marked features of this progress I will now oriefly call your attention. It may be of interest in this connection to note the following figures, showing the growth of the population of the United-States during the last three decades :

Jan 1, 1881

By Xiang-dong XING, Zhen-yang wang, Jian-Liang Zhang

Distribution behavior of titanium between CaO-SiO2-MgO-Al2O3-TiO2 and hot metal was studied between 1350 °C to 1600 °C. Experimental results indicate that the reaction temperature influenced the activity coefficients of titanium and resulted in the variation of equilibrium constant. Finally, the Gibbs free energy formula of titanium carbothermic reduction was fit out using the thermodynamic model of Wagner and congregated electron phase models.

Jan 1, 2015

By Robert Hopler

THIS paper deals specifically with heading-driving as distinguished from the broader term tunnel-driving. A heading is a pilot or path-finder for the main tunnel. Some headings are complete tunnels in themselves; that is, conditions at times warrant driving a heading the full diameter of the proposed tunnel. A tunnel 10 ft. in diameter might be driven to advantage through a single heading, provided the nature of the material admits, but it usually pays to drive rock tunnels of large diameter through the headingand-bench system. Much depends upon the material, as in soft ground tunnels of much larger diameter are driven in a single heading.

Jan 1, 2010

By D. Yamada, T. Tanaka, N. Inouchi, J. Nakahigashi, H. Yoshimura, T. Nonishi

The use of cereal food materials as lubricants was investigated in an attempt to develop nonpolluting lubricants. Suspensions of wheat flour in water and other types of cereal food lubricants were prepared and their friction coefficients measured. The results indicate that a cereal food lubricant containing 30% lipids, 2% proteins, 60% carbohydrates and 0.6% calcium carbonates has the lowest friction coefficient for a sheet (cpTi-1). As example applications, the lubricant was tested with a forming press and a screw-fastening device. In both applications the cereal food lubricant performed relatively well in comparison to conventional lubricants and thereby has potential for practical applications.

Jan 1, 2006

By J T. Carswell, K Sutton

Quality control (QC) of reverse circulation drill sampling commonly involves regular duplicate subsampling to monitor the extent of imprecision or random error in the subsampling system. In gold mining in Australia, the subsampling tool is usually a cone splitter.Other sources of error, including delimitation error and bias (systematic error) in the subsampler are often assumed to be negligible or ignored for being too difficult to QC.This paper describes actual sampling errors and error mitigation based on quality assurance and quality control (QA/QC) of surface and underground reverse circulation drill sampling at a high-nugget gold mine at Sunrise Dam, Western Australia.CITATION:Carswell, J T and Sutton, K, 2014. Sources of sampling error and implications for quality assurance and quality control in surface and underground reverse circulation drilling, in Proceedings Sampling 2014 , pp 65–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By Roger A. Bullivant

The introduction of this size and type of piling rig is intended to address a multipurpose foundation activity. The 8000 denotes the size of equipment that is attached to the mast, namely 8000 Kg. Larger equipment can be carried subject to adjustment of rig geometry. The 8000 series rig will easily accept hydraulic piling hammers and CFA equipment, but for the purpose of this discussion it will be equipped with an auxiliary power pack that is matched to twin vibrators. The design of the siamesed vibrators allows long tube equipment or piles to be driven with a short mast configuration that provides a lower overturning risk. It is easily adapted within minutes to carry out other foundation requirements that are required on the same contract. The piling and ground consolidation activities that can be undertaken by the 800 series machine are:-

Jan 1, 1995

Ventilation 'is currently used in mines to sustain human life, prevent explosions, and provide a more healthful work place. Future automated-mining systems could use ventilation techniques quite. different from today's practices. The Bureau of Mines is anticipating various methodologies for ventilating the automated mining systems which are now beginning to emerge in the mining industry. This paper examines the special ventilation requirements for automated mining systems. Topics include requirements for automated systems, current studies with blowup ventilation tubing, and ventilation of two types of highwall -ripper type mining machines.

Jan 1, 1990

By A. D. S. Gillies

Loss of visibility due to the occurrence of atmospheric fogging in underground mine airways can lead to a reduction in travel times and loss of production efficiency, an increase in the frequency of vehicular and foot traffic accidents and difficulty in checking rock surfaces for instability and loose material. Where hot and humid surface air meets colder underground air, conditions for fog formation nay be present. Further, suspended particulate matter from diesel exhausts or stoping operations together with slow movement of air along passageways nay contribute to formation. The study describes an investigation being undertaken with the cooperation of Kennecott's Ozark Lead Company to identify causes of the problem.

Jan 1, 1982