Search Documents

By William D. Mayercheck

The introduction of continuous mining machines in the late 1940's prompted the mining industry to reassess shuttle car batch-type haulage. Between place changes, the continuous miner could cut and load coal on a nearly continuous basis, but after loading a shuttle car, the high-capacity machine had to wait until the second shuttle car came inby and spotted itself under the miner tail boom. Thus, the wait-for-shuttle-car delay periods became the new bottleneck for increased coal production from the mine section. Recent studies have shown that nearly 25 pct of the continuous miner cycle time is consumed by delays in the haulage system, usually waiting for shuttle cars. Computer simulations of a face operation indicate that up to a 45 pct increase in coal production may be realized through the use of a continuous haulage system, assuming of course that the outby haulage system can handle this increased capacity. Coincidently, there are recent claims by some mines using continuous face haulage of a production increase of 45 pct compared with shuttle car haulage. These documented production records, computer simulations, and common sense indicate the potential of continuous face haulage in underground coal. The late 1960's and early 1970's saw several mining machinery manufacturers market mobile bridge carrier and piggyback bridge conveyor continuous haulage systems for use in underground coal mines. These systems have shown limited potential in some mines and outstanding success in others. It appears that no one system can be universally applicable to all underground mining conditions; thus, the Bureau of Mines has conducted extensive research over the last few years to investigate different types of continuous haulage systems for use in high and low coal seams that will advance the state of the art.

Jan 1, 1977

By S. K. Kawatra

Many mineral oxide and multi-component oxide (basalt) specimens break down into powders upon expo-sure to sodium vapor at elevated temperatures for extended times. This paper examines several possible mechanisms of oxide breakage by sodium vapor, both experimentally and from a thermodynamic viewpoint. The oxides for which reduction by sodium was thermo-dynamically favorable all exhibited some degree of fragmentation. The oxides which were not favorable for reduction by sodium did not exhibit fragmentation, with the exception of rutile, a titanium oxide. The rutile fragmentation was caused by the reduction of iron that was in solid solution in the rutile crystal structure.

Jan 1, 1995

By W. H. Bassett

Beads of metal frequently appear at the ends of cast-copper wire bars and on the sides of wedge cakes near the top. These are richer in cuprous-oxide than the rest of the casting. A micrographical study of these exudations has been made. It is suggested that the material is forced through the surface while the copper is solidifying. If not eliminated in process of manufacture, it shows on the finished polished sheet copper in patches differing in color from the main body of the sheet. FIGURES 1 to 4 show the copper exudations, at different magnifications, as they appear on the ends of cast wire bars, and on the sides, usually near the top, of wedge cakes. Sometimes the exudations are in fine "drops;" at other times, large masses of the material are found. Microscopic examination of the copper exudation indicates that it is high in oxide and of eutectic proportions. Because of the difficulty of securing a suitable sample, the protuberances have not been analyzed chemically; but the spectroscope shows no indication that there are any more metallic impurities present than in the balance of the copper. The lowest copper plus silver content of the coppers studied for this? paper was 99.914 per cent.; the highest, 99.966 per cent.; so the oxygen content of the whole casting would be well under 0.07 per cent.

Jan 2, 1926

By John W. Trammell, Chester O. Ensign

Efficient mining of copper ore at the White Pine mine in Michigan's Upper Peninsula is partially dependent on the rather unique problem of predicting variations and rock types in a barren stratum called the upper sandstone. The pronounced effect which this formation has on the local mining techniques is reflected by the necessity of deciding whether to mine the sandstone along with ore-bearing rock, thus diluting overall ore grade, or, alternatively, leaving the sandstone behind to form the mine roof. THE OREBODY AND MINING TYPES In the mine, the cupriferous zone of the Nonesuch shale is divided into three major portions (Fig. I). Lying conformably on top of the Copper Harbor formation (or "lower sandstone") is the lower part of the orebody, the parting shale. The parting shale is overlain by the upper sandstone. On top of the upper sandstone, the basal portion (8 ft) of the upper shale is quite similar to the parting shale. Both the upper shale and parting shale are divided into a number of smaller stratigraphic units, each having a characteristic copper content, as shown by the histogram of Fig. 1. Other authors have dealt in detail with the stratigraphy and mineralogy of the orebody, so it will suffice here to call attention to the low copper content of the upper sandstone.

Jan 12, 1964

By K. Kar, A. Sreeoath, M. Gautam

"This paper presents results of an experimental investigation of the sampling efficiency of a blunt cylindrical sampler oriented with respect to the oncoming flow. The number of particles sampled by the cylindrical blunt sampler and an isokinetic sampler is measured using the TSI Aerodynamic Particle Sizer. A technique is described to conven the ratio of the particles sampled into the sampling efficiency. The experimental data thus obtained is then compared with the impaction model of Vincent and Mark (1982) with the empirical constant determined from our experiment.. The comparison shows excellent agreement for 0° and 90° orientation.1.0 IntroductionCylindrical dust samplers are widely used in practice to determine the concentration of the airborne particulate matter. The sampler is simply a means to collect particles from the ambient, whose concentration is subsequently measured by some size selective techniques. Gravimetric and optical techniques are the two most commonly used methods to measure the particle sizes. While impactors are used in gravimetric analysis, Aerodynamic Particle Sizer, Aerosizer. Electron microscope, Coulter Counter etc. use the optical method to measure the particle sizes. The Aerodynamic Particle Sizer (APS) and the Aerosizer are the new generation devices which employ the time of flight of particles within intersecting laser beams to determine the particle size.The introduction of the sampler in the free stream disturbs the flow pattern due to two distinct actions of the sampler on the fluid stream: one of them results due to the conformity of the flow to the geometry of the circular cylinder and the second one is caused by the flow into the suction orifice. If the sampler performance is determined by the number of particles entering into the sampler inlet relative to the number of particles present in the free stream, then the particle trajectory outside the sampler and into the inlet is the deterministic factor for the sampling efficiency. The particle trajectory inside the sampler is not important in this case."

Nov 1, 1995

By D Pearce

The 15-year long debate between the industry, Government and Aboriginal people about the rights and wrongs of Land Rights, the right of Aboriginal people to control development on their land and the relationship between the parties, has been long and often bitter. It has so far been a war of words and often the truth has been the first casualty. This paper looks at the debate and presents the perspective of Aboriginal people, as well as looking at how the industry and Aboriginal people can work together for everyone's benefit. It addresses such matters as: ò why Aboriginal people believe they have the right to control development on their land; ò the perception that Aboriginal people are anti-development; ò the perception that Aboriginal land is 'locked-up'; and ò how companies can negotiate with Aboriginal people.

Jan 1, 1994

By Veronique Falmagne

"In 1987 the only knowledge available of the Ansil orebody was that it was high grade, deep and relatively small . High stresses were also anticipated because there had been rockbursts during shaft sinking and destress blasting had been necessary (Fig. 1). From the design, through the development and now in the mining stage, rock mechanics and microseismic monitoring have been used to maximize recovery and safety and minimize dilution. Examples are given of the use of a microseismic monitoring system in the early stages o f mining. This paper also presents a review of the mine's in situ stress measurement campaign, cable bolting practice and backfill procedure.The Design PhaseAfter the initial mapping and classification work, preIiminary numerical modelling was performed using assumed stresses of ov = oH and oH = 3ov• The empirical Mathew's analysis was then used to optimize stope dimensions based on geomechanics data available at the time (Bawden et 01., 1988; Falmagne, 1987; Potvin et 01., 1988). Because of high stresses predicted by numerical modelling and a brittle, strong and relatively unfractured host rock which was believed to be rockburst prone, it was decided to mine without temporary or permanent pillars. However, in order to satisfy production rates, the orebody had to be broken up into two horiwns separated by a triangular pillar (Fig. 2). The final mining sequence is shown in Figure 3.The Development PhaseAt this point, based on work accomplished to date, including mapping and observations from drifting and modelling, the following problems were identified: (1) flat backs in the hangingwall andesite were thought to be highly stressed; (2) flat backs in weak massive sulphide ore would also be subjected to high stress and be difficult to support; (3) the felsic dyke was noted as a "" stress raiser"" , because activity increased as drifts approached it; and (4) chlorite coating of joints in the hangingwall was thought to be an important factor in reducing their stability."

Jan 1, 1991

By Jacob Carr, Bruce Whisner, Adam Smith, Jingcheng Li

Electromagnetic-based proximity detection systems (PDSs) are utilized on mining machinery to protect workers from being pinned or struck. These systems generate magnetic fields covering the space around a machine, and a miner-wearable component (MWC) detects the field. The PDS determines the distance of miners relative to the machine based on the detected magnetic flux density in the magnetic field. This information is used to establish warning and shutdown zones around the machine. Maintaining a stable magnetic field is essential for system accuracy. However, components used to generate magnetic fields can be influenced by temperature changes. Depending on ventilation conditions and seasonal alternation, a PDS can be subject to significant temperature fluctuation. To better understand and quantify this phenomenon, researchers from the National Institute for Occupational Safety and Health (NIOSH) developed an experimental apparatus to study the influence of temperature on magnetic field generator circuits used in PDSs. Results from the study show that the electric current through a generator can be influenced by both ambient and internal temperatures, modifying the magnetic field that is produced. These findings show that temperature can significantly influence the ability of PDSs, used in underground coal mines, to accurately determine a worker’s position in relation to mining machine.

By D. S. Burgess

An investigation of the hazard of spillage of liquefied natural gas (LNG) onto water is described. About 2,000 gallons of LNG were consumed in various tests. The initial vaporization rate of LNG following spillage was found to be 0.037 lb/ft2 sec; when the spill was confined, this vaporization rate was moderated after about 20 seconds by the growth of an ice layer on the water surface; when the spill was unconfined, a coherent ice floe was not observed and the vaporization rate was essentially time independent. The maximum diameter (in feet) of the spreading LNG pool was found to be given by 6.25 Wo 1/3, where Wo is the weight of LNG in pounds, Downwind of a natural gas source, time-averaged methane concentrations were given in good approximation by standard air pollution equations. However, peak concentrations were as much as twentyfold higher than average, adding an additional factor to the assessment of hazard. The effect of layering by the cold vaporized natural gas was similar to the effect of a temperature inversion on normal gases in the atmosphere. Small-scale explosions were observed on pouring LNG onto a water surface; no single explanation seems pertinent to all of the incidents observed.

Jan 1, 1970

By Frame Ritzert, Dennis Keller, Vijay Vasudevan, David Arenas

"An investigation was conducted to describe topologically close packed (TCP) phase instability as' a function of composition in the advanced ·Ni-base superalloy Rene N6. TCP phases are detrimental to overfill high-temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements. Thirty-four variations of polycrystalline .Rene N6 determined from a design-of-experiments approach were cast and homogenized at 13 l5°C for 80 hours followed by exposure at 1093°C for 400 hours to promote TCP formation. The alloys had the following composition ranges in atomic percent: cobalt 10.61 to 16.73, Mo 0.32 to 1.34%, W 1.85 to 2.52%, Re 1.80 to 2.11%, Ta 2.36 to 3.02%, Al 11.90 to 14.75%, and Cr 3.57 to 6.23%. Physical and chemical characteristics of all microstructures obtained were described using various analytical techniques. From these observations, a mathematical description of TCP occurrence (s and P phase) was generated for polycrystalline Rene N6.IntroductionNi-base superalloy single crystals represent the state-of-the-art for turbine engine airfoil application as they offer the best balance of properties to allow for the high operating temperatures required: for efficient engine operation.1 Current trends in alloy design take advantage of improved creep rupture strength with the addition .of higher levels of refractory elements. 2 In .particular, the addition of significantly higher levels of Re in third generation superalloys is key for both microstructural stability and creep rupture strength. 3 While the presence of the refractories is thought to provide strength benefits from solid solution hardening, a tendency for alloy instability in the form of topologically-close-packed (TCP) phases or secondary reaction· zone (SRZ) ·phenomena accompanies the high refractory content. 3 The formation of these phases in sufficient amount is detrimental to the overall high temperature performance of Ni-base superalloys because of their brittle nature and because they deplete the Ni-rich matrix of potent solid solution strengthening elements.4 The tendency for a particular composition to form TCP may not be immediately known since the precipitation of TCP phases in Ni-base superalloys is nucleation controlled, thereby requiring long times at elevated temperatures to precipitate. 5 They preferentially nucleate along the octahedral planes of the Ni-base superalloys, usually in areas of refractory metal enrichment at grain boundaries or inside dendrites.5-6 In Rene N6, two closely related TCP phases, a and P, have been observed.2"

Jan 1, 1998

By E Donskoi

In order to develop downstream processing routines for iron ore and to understand the behaviour of the ore during such processing, extensive mineralogical characterisation is required. To determine mineral associations, mineral liberation and grain size distribution, imaging techniques have to be used. There are two main imaging techniques used for the characterisation of iron ore, ie, Optical Image Analysis (OIA) and Scanning Electron Microscopy (SEM). In this article a QEMSCANTM system is used as an example of SEM methodology and results obtained from it are compared against results obtained by the CSIRO ‘Recognition3/Mineral3’ OIA system.Both OIA and QEMSCANTM systems have advantages and drawbacks. Even though the latest QEMSCANTM systems can distinguish between major iron oxides and oxyhydroxides, it is still problematic for QEMSCANTM to distinguish between iron ore minerals very close in oxygen content, eg haematite and hydroheamatite, or between different types of vitreous goethite.QEMSCANTM also can misidentify minerals with close chemical composition, ie haematite as magnetite and vitreous goethite as haematite. In OIA, iron minerals with slight differences in their oxidation or hydration state are more easily and directly recognisable by correlation with their reflectivity. In both methods, the presence of microporosity can result in some misidentification, but in SEM methods misidentifi cations due to microporosity can be critical. Low resolution during QEMSCANTM analysis can significantly affect the textural classifi cation of particle sections.The main conclusion of this study is that, for low iron content ores or tailings, QEMSCANTM can provide much more detailed information on the gangue minerals than OIA. However, for routine characterisation of iron ores with high iron content and containing a variety of iron oxides and oxyhydroxides, OIA is a faster, more cost-effective and more reliable method of iron ore characterisation. A combined approach using both techniques will provide the most detailed understanding of iron ore samples being characterised.

Jul 11, 2011

The Objective: To reduce the noise generated by the exhausting air from a pneumatic roof bolting drill to a maximum of 90 decibels. Any attachment used for this purpose must be lightweight and must not cause a significant increase in back pressure. The Approach: Absorb the noise with a properly designed muffler that will permit sufficient airflow without affecting the normal operation of the drill. How It Works: The air exhausted by the drill enters the muffler through perforated disks into a resonator chamber. It then passes through a series of expansion and contraction chambers and is expelled to the atmosphere through another perforated disk. The basic muffler design for the pneumatic drill was established by using both digital computer analysis and experimentally simulated noise tests. The measured parameters used in the computer program consisted of inlet and outlet pressures, temperatures, airflows and exhaust areas. United

By Jerome P. Downey

The Indium Corporation of America - Colorado School of Mines Indium Separation Technology was evaluated as a potential means of treating smelter flue dusts stockpiled at the Pintlar Corporation property in Kellogg, Idaho. The patented technology represents a method for segregating the contained indium, lead, and other metals in forms acceptable for downstream processing and recovery. Separation is effected by treating the dust with metallic sodium in a bath of molten lead. Process effectiveness was measured by determining the relative distribution of key metals between the bullion and dross products at small pilot plant scale. The study indicated that application of the technology to the Pitlar samples results in a highly efficient concentration of lead in the bullion, while indium is collected in the dross. The distribution of other key metals between the bullion and dross products and the effect of varying selected process parameters are also discussed.

Jan 1, 1994

By C Itotoh, K O’Halloran, L Karlson

Global methods used to explore for minerals have progressed relatively slowly since the development of the first diamond core drill in 1863. Since then, key developments such as wireline geophysics (1920s), the tricone drill bit (1930s) and aeromagnetic surveys (1940s) all occurred in response to global events. In this project, BHP’s WAIO Geoscience operations team hypothesise that a global movement towards a greener future as well as an increasing intolerance for safety events will drive another step change in exploration methods. We have leveraged our relationships with exploration contractor partners and industry leaders to develop a realistic vision for 2033 and beyond, where drill rigs, earthworks and geophysical units are operated and maintained remotely; emissions of dust and waste are eliminated; hazardous energy sources are controlled; procurement is based on sustainability rather than cost and carbon emissions are tracked with the same rigour as production metrics. We have combined these visions into a series of graphical illustrations with the aim of inspiring ourselves, our vendors and our peers to collaborate further on producing a step change in our industry.

Sep 18, 2023

By D. Pacey

"This paper reviews the installation, start-up, and operation of a comprehensive monitoring and targeting management technique in which all plant utilities (i.e., electricity, natural gas, compressed air, and water) are managed as controllable resources in the same way that raw materials, mined ore, personnel and capital are managed.The essential elements of monitoring and targeting (M&T) include:•gathering in a systematic, disciplined way the utility information by energy account centres;•closely monitoring the utilities used in each centre and comparing them with production on a common time base (e.g., kWh/ton per day);•bench marking and target setting to pro-vide attainable energy reduction goals which can be further refined as they are achieved; and•establishing an implementation plant that may provide efficiency enhancing benefits to various operating areas within the plant.The M&T system will reduce utility consumption per unit of production on a continuing basis.This would translate into sustained operating cost and waste. M&T will also provide better information for assessing the plant operation and progressively implementing further enhancements."

Jan 1, 1997

By AIME AIME

THE following paragraphs, constituting the concluding portion of the Annual Report of the Council for 1903, have been withheld from publication until now, in order to make them as accurate and complete as possible. They will be published in Volume XXXV. of the Transactions in their proper place at the end of the said Annual Report. Franklin Ballou was born in Pittsburg, Pa., May 29, 1845. He was the son of an old resident, Arthur Ballou, a manufacturer and wholesale dealer in vinegar. In early youth Franklin attended the Western University of Pittsburg, but left school at the age of 16 to become book-keeper for his father, upon whose retirement from business, in 1868, he associated himself with Walter C. Childs, of Pittsburg, in the manufac¬ture of furnace-grates and asbestos-cement for blast-furnaces. This firm was known as W. C. Childs & Co., and did a success¬ful business for several years. In 1869 Mr. Ballou married Miss May S. Wilson, daughter of Judge Wilson, of Lewistown, Pa. In 1876 he spent several months traveling in the West and studying the mining industry, which greatly interested him. In consequence of this journey, he wound up his business in Pittsburg and removed in 1877 to Georgetown, Colo., where for several years he conducted a sampling-works, and built up an extensive business as an agent for the sale of ores, besides engaging to some extent in mining enterprises. , It is said that he controlled at one time about one-eighth of the output of the Leadville mines. In the early 80's, he became Vice-President and General Manager of the Bimetallic Smelter at Leadville, of which Mr. David H. Moflat was the principal owner. This was practically the first successful demonstration of pyritic smelting in Colorado. Upon the sale of the works in 1897 to the American Smelting and Refining Co., Mr. Ballou retired

Jan 1, 1905

By Richard D. Hagni

Quantitative techniques have become increasingly important in recent years in the study of ore minerals. Precise measurement of indentation hardness and reflectance is the most important quantitative ore microscopic technique for mineral identification. Reflectance measurements of various wave lengths under monochromatic light provide the data necessary for the preparation of spectral reflectance curves and for the quantitative determination of an ore mineral's color. The procedures for the measurement of indentation hardness, reflectance, and color coordinates have recently been standardized and 204 items of quantitative data for ore minerals are now available in the first issue of the quantitative data file of the International Mineralogical Association's Commission on Ore Microscopy. A number of systems utilizing these quantitative data for systematic ore mineral identification have been published and others are in preparation. Rotation properties, although not included on the data cards, are useful in the identification of certain groups of minerals. Other aspects of quantitative ore microscopic techniques include the utilization of automatic image analysis for mineral percentage determinations and the use o~ various microbeam instruments for elemental analyses. These techniques provide a greatly improved basis for mineral identification in mineralogical and beneficiation studies.

Jan 1, 1981

"Far from being eclipsed by petroleum and natural gas, Canadian coal continues to command wide (and apparently growing) interest.Major R & D investigations are currently heavily oriented toward coal beneficiation (e.g., cleaning and utilization of fines) and toward a broad range of studies on metallurgical coals and cokes. However, active work is also being carried out in the areas of coal geology, mining, transportation and combustion; and, in some laboratories, increasing stress has been laid on developing a number of new, essentially non-fuel uses for coal and coal products.This review summarizes the work of Canadian coal research agencies during 1966 and indicates some of the more important advances made by them."

Jan 1, 1967

By B. W. Naugle

Twenty-nine sole-heated-oven expansion teats were made on 9 different coals, and apparent specific-Brevity tests were made on 12 of the resultant cokes. The coals, which ranged in dry, mineral-matter-free fixed-carbon content from 58.7 to 81.1 percent, were tested over a rather wide range of moisture content and dry-coal bulk density to determine the separate effects of these variables on linear coal expansion. The experimental data support the follow expression relating "as-tested" coal bulk density, moisture content, and linear expansion, [ER = (1-MR) (1+Et) - 1; BDt] where ER = fractional expansion at a reference bulk density of 55.0 lb. of 1 percent moisture coal per cu. ft., Et = fractional expansion at Mt and BDt, MR = reference moisture content = 0.01, Mt = moisture content, "as-tested", BDR = reference bulk density = 55.0 lb. per cu, ft., BDt = bulk density, "as-tested", 1b. per cu. ft.

Jan 1, 1957

By Petrus Christiaan Pistorius, Ming Tang

Magnetite concentrate is pelletized and then hardened by elevated-temperature oxidation to hematite, to produce pellets for ironmaking. Previous work showed that the rate of oxidation is under mixed control of gaseous mass transfer of molecular oxygen through the pellet pores, and solid-state diffusion into the oxidizing grains. Because of the partially limiting role of solid-state diffusion, concentrate size distribution strongly affects pellet oxidation. Previously, a simple mixed-control model was formulated to describe isothermal oxidation. In that model, the main effect of concentrate size distribution was on the plateau level of oxidation which is reached at a given temperature. However, the extent of plateau oxidation increases with increased temperature, requiring a more complex model for non-isothermal oxidation. In this paper, predictions of the non-isothermal model confirm the strong effects of concentrate size distribution and oxygen enrichment. In particular, a greater fraction of coarse magnetite particles would be beneficial, decreasing the size of the macroscopic unoxidized pellet core.

Jan 1, 2015