Search Documents

By Marwan M. Mohammed, Hani S. Mitri, Wilfrid Comeaul, Baoyao Tang

In many parts of the world, rockbursts have become a major problem of mining at depth. As orebodies are being mined deeper, rockburst phenomena have become familiar to deep hard rock mines. Rockbursts are generally characterised by sudden release of energy in a volume of highly stressed rock, which can cause local violent failure of the rock mass around the opening. One method of controlling these failures is to precondition the rock mass by detonating fully confined explosive charges at the appropriate locations. This method known as destress blasting, was first tried in the deep South African gold mines (Roux et al., 1957), and was widely used later in Canada, United States, France, Poland and Japan.

Jan 1, 1999

By T. E. Bernard

The CO2-absorbent canisters used in four approved rescue breathing apparatus were investigated. A breathing machine was used to simulate human expiration with gas flow rates of 26, 37, and 48 1/min of 3.5% CO2 in air. The exit gas CO2 concentration, the pressure drop across the canister, and the exit-gas temperature were monitored. The absorbent capacities of the packed-bed canister designs were found to be dependent on flow rate within the range studied, while the capacities of the other designs were less affected. The radial canister had the least resistance to breathing while the complex bed design proved to be the most effective in utilization of the chemical. The overall results indicated that LiOH (lithium hydroxide) has the highest capacity for CO2 absorption among the absorbents tested. It can be used in a simple packed-bed design while maintaining acceptable levels of resistance and exit-gas temperature. Examination of oxygen supply with respect to CO2-absorption capacity suggested that it is desirable to closely match CO2-absorption capacity with the avail-able O2 supply to minimize the size and weight of rescue breathing apparatus.

Jan 1, 1979

By J. H. Tylczak

The Bureau of Mines studied the effect of alloy additions on abrasive wear of low-alloy steels. A dry-sand, rubber-wheel abrasion test appa-ratus using ASTM G65-Sl procedure B was used for the abrasive wear tests. Eighty-six material heat-treatment combinations were abrasion tested. Results of these tests were analyzed statistically using regression analysis to see if additions of Cr, Mn, Mo, Ni, Si, AI, Cu, and S were significant in affecting the abrasive wear rate of low-alloy steels. Regression analysis was also used to confirm hardness and C affect on the abrasive wear rate of these steels. It was found that for all the steels taken as a group, increased amounts of Mn significantly reduced the wear rate, while increased amounts of Mo and S1 increased the wear rate. Analysis also confirmed previous research done by others, that increasing hardness and amounts of C reduced the wear rate. For the hardened steels taken as a class, only increasing amounts of C and Mn reduced the wear rate, while increases in Si increased the wear rate. In the class of unhardened steels, increases in C, Mn, and S re-duced the wear rate, whereas increases in Mo increased the wear rate. The steels with the best resistance to wear were two hardened experimen-tal steels similar to AISI 1055 and AISI 107S.

Jan 1, 1986

By D. E. Walsh

Over a period of seven years (1989-1996) the Mineral Industry Research Laboratory (MIRL) University of Alaska Fairbanks, has investigated the effects of temperature, residence time, and particle size on the degree of low-rank coal (LRC) upgrading for a non-evaporative, hydrothermal drying process, also known as hot water drying (HWD). Three Alaskan LRCs were used in this study: Usibelli coal (Seam No.4) from the Nenana Coal Field, Little Tonzona coal from near McGrath, and Beluga coal from the Beluga-Yentna field on the west side of Cook Inlet. Replicated, factorial tests were conducted. Experimental results indicate that most of the low-rank coal upgrading via HWD occurs rapidly within the first 10-20 minutes of residence time. Thereafter, the upgrading process slows down and over 100 minutes of additional residence time are required to produce similar percentage increases in coal properties to those achieved in the first 10-20 minutes. The properties of the hot water dried products were very sensitive to process temperature. Calorific value, carbon and oxygen contents, equilibrium moisture levels and Hardgrove grindabilities all appear to change linearly with temperature within the 275" C to 325" C range.

Jan 1, 1997

By C. Kremer Bain

DURING the past several years of diamond drilling in Washington County, Mo., the St. Joseph Lead Co. has discovered a concentration of commercial lead-zinc ore at four different points within an area of 36 square miles. The largest and to date the most promising group of these orebodies is located in the Indian Creek area. It was considered to be of sufficient value to warrant development.

Jan 9, 1953

By Jr. Watts, B. K. Cantrell, K. L. Bickel, J. F. McDonald

"A field trial was conducted at an underground gold mine to evaluate diesel fuel derived from soybean oil (soy-methyl-esters or “biodiesel”) as an alternative to commercial, low-sulphur, number 2 diesel fuel (D2). A 2.7 m3, 18-ton load-haul-dump (LHD) unit, powered by a naturally aspirated, indirect injection (pre-chamber), 100 kW diesel engine was used as the test vehicle. The LHD was equipped with a diesel oxidation catalyst. The LHD operated satisfactorily on the biodiesel fuel. Operators observed a slight decrease in power and an absence of black smoke.Diesel particulate matter (DPM) concentrations were monitored for a six-week period while the LHD was operated with either the biodiesel fuel or the D2 fuel. DPM concentrations were measured in the mining section’s clean air intake, exhaust and on the LHD. Reduction in DPM emissions was determined from the measured difference in DPM concentrations between the clean air intake and the exhaust. The biodiesel fuel reduced energyspecific DPM emissions approximately 75%, from 3.6 ± 1.8 g/kW-hr to 0.86 ± 0.27 g/kWhr. Time-weighted average DPM exposure, measured near the LHD operator, was reduced from 0.67 ± 0.13 mg/sm3 to 0.28 ± 0.12 mg/sm3, or approximately 58%, when the biodiesel fuel was used. IntroductionDiesel exhaust consists of noxious gases and diesel particulate matter (DPM). Recent attention has focussed on the potential carcinogenicity of DPM and the potential health impact on miners. The National Institute for Occupational Safety and Health (NIOSH) recommended that whole diesel exhaust be regarded as a “potential occupational carcinogen”, and that reductions in workplace exposure would reduce cancer risks (NIOSH, 1988). The International Agency for Research on Cancer (IARC) declared that “diesel engine exhaust is probably carcinogenic to humans” (IARC, 1989)."

Jan 1, 1997

By C. C. Harris

The two best known graphical methods for presenting and comparing comminution data are obtained by linearising the Gates-Gaudin-Schuhmann and the Rosin-Rammler size distribution equations. It is shown that the Gates-Gaudin-Schuhmann equation can cause excessive congestion in the 50 per cent oversize range and that, overall, the Rosin-Rammler is a better procedure. Examples are given

Dec 1, 1971

By Rowena Anderson

Mining companies are now looking for more effective ways to engage the community in public participation. Consensus-based approaches are becoming the most popularly applied way of achieving meaningful public participation. This paper introduces the principles surrounding consensus-building approaches and the processes for getting them started. The Healthy Communities Movement is one such consensus-based approach that offers a well-established holistic model for conceptualizing a healthy sustainable community. It also highlights the importance of public participation as an essential component of achieving a sustainable community. The paper concludes by illustrating how current company-community relations programs can utilize these models.

May 1, 2002

By Susan Fredholm, Randolph Kirchain, Jeremy Gregory

"Jurisdictions across the world have struggled to create and finance systems that can effectively collect and process electronics waste (e-waste). Many different system architectures have been proposed and implemented, but it is difficult for policy-makers and system architects to compare the costs and benefits of different systems, particularly when the systems operate in different contexts. This paper presents a systematic methodology that seeks to address this challenge and uses data from several existing electronics recycling systems across the world to illustrate its implementation. The methodology characterizes three main system characteristics: architecture (e.g., financing and collection methods), context (e.g., jurisdiction population, density, and wages), and performance, both economic and materials collection. A comparison of systems in Europe and North America with different system architectures and contexts illuminates the importance of using the methodology to discern the extent to which architecture and context drive system performance.IntroductionElectronic waste (e-waste) recycling offers several environmental benefits when processing is done responsibly. The controversy around e-waste recycling systems rarely debates such benefits; rather, it focuses on the characteristics of an effective system and whether benefits outweigh costs. Historically, the costs of recycling most electronics have outweighed the value of the scrap recovered. Thus, in the absence of legislation, e-waste recycling systems have been limited to private recycling of high-value waste with minimal consumer participation. E-waste recycling systems now exist in many locations worldwide including Asia, the European Union, Canada and the United States and the amount of related legislation continues to increase. Numerous approaches have been proposed including landfill bans, extended producer responsibility (EPR) and consumer advance recovery fee (ARF) funded recycling systems."

Jan 1, 2008

By W. M. Raynor

LARGE quantities of "midnight oil" have been consumed by researchers in attempting to develop a process to produce cold ductile zirconium at low cost. The tantalizing facts that zirconium is a bright, silvery, tarnish-proof metal and is 2 1/2 times as abundant in the earth's crust as copper, and thirteen times as plentiful as lead have resulted in much speculation on uses, ranging from automobile radiator grills to kitchen sinks. but unfortunately no low-cost process of producing it has so far been found. In the case of zirconium, we cannot say that "virtue is its own reward" for the principal virtues of the metal, namely, corrosion resistance at ordinary temperatures and ability to absorb gases at high temperature, are the very characteristics that defeat all of the usual recovery methods such as sintering, plating, or direct chemical reduction. The only method giving a pure metal sufficiently low in oxides, nitrides, etc. to be truly cold-malleable is the one developed by Van Arkel and DeBoer in 1925. This process involves decomposition of zirconium tetraiodide in contact with a hot filament and pre

Jan 1, 1947

By H. R. Manouchehri

The importance of the grinding environment and its effect on sulphide minerals flotation behavior has been known for many years. The grinding environment may play a role in controlling fine and coarse particle flotation along with dissociation of different chemical species in grinding environment. Dissociation of different chemical species and ions within the process water may result from changing the grinding environment. The mining and mineral processing industry undertakes activities that may impact on water resources. These include use and storage of chemical storm-water management, process water management, mine dewatering and management of tailings. In mineral flotation understanding and controlling water quality is paramount important not only because of its effect on flotation but also with respect to control the quality of the water which is released to the environment. Releasing of different anionic and/or cationic chemical species in the process water results from the interactions among different mineral within the ore, process water, and the milling environment. In fact grinding mill acts as an electrochemical reactor which affects the flotation performances of different value minerals as well as the quality of the tailing products. An increasing in antimony content in process/discharge water at Boliden?s Tara processing plant in Ireland to above limitation level was reported in April 2010 which needed to be controlled. An increase up to 6 times of the permitted level was reported which needed an immediate action to control due to environmental considerations. Therefore attempts were made to detect why this higher amount of Sb is released and how to control and minimize its release to the process/reclaim water. This paper discusses how/why Sb content in process/reclaim water was increased by changing the mill electrochemistry and the strategies were taken into considerations to control it. Different strategies, including electrochemical controlling of the milling section, Fenton process, using Bauxsol in treating the process water, etc., have been considered and tested which are described herein. All strategies taken into consideration for solving the problem were successful which indicated good understanding of the issue and good decision making. Furthermore, for each solution the capital and operational costs were roughly estimated. Accordingly, the Sb content in process/discharge water was controlled to a value lower than allowed limitation, i.e., 1 ppm. Keywords: antimony, water contamination, mill electrochemistry, ag milling, grinding media, eh-ph, sulfide minerals, fenton process, bauxsol, lime addition

Sep 1, 2012

By Kellerwessei H, Oberheuser G

A major breakthrough in extending the life of the wear material of high pressure roll crushers when treating moist, highly abrasive material has removed the last impediment to the widespread acceptance of high pressure comminution in the minerals industry. The system is very energy efficient. It has been demonstrated that in the cement industry energy savings of up to 50 per cent have been achieved compared to conventional hall milling. Besides being energy efficient, the process provides some remarkable and useful effects; ò better liberation of mineral constituents (as proven for diamond liberation). ò preferential comminution where induced micro fissures follow grain boundaries. ò higher reactivity of the product due to micro fissures. All these points will be described here together with a review of current flowsheet design and incentives for the use of this method of Comminution.

Jan 1, 1993

By Chanhwi Shin, Hyeongmin Kang

Mine optimization is a key strategy in the mining industry that focuses on improving the efficiency, productivity, and sustainability of mining operations. To achieve mine optimization, digitalization is essential for modernizing mining operations and attaining optimal performance. Due to the importance of mine digitalization, various software and platforms have been released to support this effort. Furthermore, by integrating these advanced technologies, mines can enhance processes, leading to significant economic and operational benefits. However, integrating data from various sources and collaborating across different platforms remains a significant challenge in the mining industry. Generally, data for mine optimization, such as mapping, smart drilling, FMS (Fleet Management Systems), fragmentation analysis, or vibration analysis, are collected and analyzed separately on different platforms. This separation makes it difficult to aggregate and utilize data comprehensively for overall mining process optimization. During the digitalization process, obstacles arise due to these complexity, variability, and sharing issues of data across different maker, sources, and methods. These challenges highlight the need for seamless integration to achieve optimal mining operations. Thus, this study applied a total solution that can cover the entire Drilling and Blasting (D&B) processes. The blast design was performed using actual terrain mapping data, and drilling and charging were conducted following a guide based on the blast design plan. After blasting, loading and hauling distances and fuel consumption were measured, and fragmentation for each blast was evaluated. All measurement tasks were automated to minimize human error. By collecting all data in one server, it became possible to perform an overall evaluation for each blast, allowing the identification of optimal values. In conclusion, to evaluate the optimization effects for each mining process, one month of integrated data collected on a single server was used. Compared to the period before the Total solution was implemented, there were notable improvements: a 25% enhancement in hole spacing, a 60% improvement in floor flatness, a 23% reduction in average fragment size, and a 19% improvement in fragment uniformity. Regarding cost savings per blasting volume, the improvements were 11.7% in drilling, 9.3% in explosives, 7.6% in loading, and 17.5% in hauling.

Jan 21, 2025

By H. R. Huffman

"This paper reviews the history of iron powder production, and outlines the varions production methods. The uses of iron powder and the reasons for its use are also covered. The paper concludes with a look at future trends in powder metallurgy.INTRODUCTION TO POWDERSTHE IRON POWDER INDUSTRY is enjoying a very rapid growth. The annual consumption of iron powder is now at the 100,000-ton level, twenty times higher than it was at the end of World War II, and the yearly in-crease bas been almost consistent at 20 per cent. This is expected to increase, bringing the tonnage to 200,-000, or even (according to some experts) to 270,000, in 1970. In any event, powder metallurgy is expanding at high speed and making an important impact on the production of iron and steel products. Some indication of the faith in the future market may be indicated by the commencement of three new powder production plants in Canada with a total capacity of 136,000 tons annually."

Jan 1, 1969

By G. Herget

"A brief visit to European longwall mining operations in potash showed that retreating longwall mining provides a very attractive alternative to room-and pillar mining, especially in areas with bad roof, narrow seams and areas with high ground pressures. Mines de Potasse d'Alsace, France converted all potash operations to longwall mining in 1980. Recovery rates per panel vary between 75o/~ to 85% which compares very favourably with Saskatchewan values. Ground pressure in Saskatchewan are comparable to those of some of the deposits in Europe, but the presence of water in the hanging wall of Saskatchewan orebodies has to be given serious consideration. However, given the mining experience in Saskatchewan and the improved technology f or laboratory and field investigations, a review of present mining practice in Saskatchewan is desirable. IntroductionLongwall mining is practiced widely in coal mining and allows complete mechanization. It is applicable at great mining depth, in thin seams, weak roof and has been applied recently even to coal bed s dipping more than 65 degrees. Ideally this system allows complete extraction of an orebody. However, with high mechanization and emphasis on obtaining high outputs per man shift, extraction ratios rarely reach more than 80010 per panel.France, Spain and the U.S.S.R. have had longwall operations in potash for some time and a brief description is given below. Two of the operations were visited and the Russian operation is described based on German literature"

Jan 1, 1986

By C. H. Lieb

ONE astounding fact in the production of petroleum is the comparatively recent realization by producers that flowing production is the cheapest crude produced. About 1910 or even later, operators actually endeavored to get a producing well to pumping as quickly as possible after completion. A well was not really considered to be completed until it was operating on the pump. Remarkable progress has been made since then. It was not until about 1920 that producers began to take a serious interest in pressures and to think a little about proper methods of handling oil wells. Pressure gauges were installed, and records of pressures maintained, which was quite an innovation. Desultory experiments were made with tubing of different sizes, as well as experiments with placing the bottom of the tubing string at different levels in the well. Probably the first important departure from customary procedure was about 1926, during the Seminole development, when gas lift

Jan 1, 1936

By J Kinal, I Mitchell

Many flotation plants use pH to adjust the pulp chemistry of their system to achieve optimum separation. For example, in a sequential lead/zinc circuit the pH during sphalerite flotation is increased to 10.5 or greater to depress galena and pyrite, thereby improving selectivity for sphalerite. However, maintaining a pulp at a particular pH value does not necessarily provide the operator with an abundance of information regarding the chemistry changes occurring within a plant. This paper provides the reader with a number of pulp chemical observations in several plants, showing that the same trends are noted over time; however, the magnitude of the measured values do change. Further, the changes in magnitude are invariably associated with a change in mineralogy. Thus, is measuring pH enough? Can the Eh, dissolved oxygen and temperature be measured at the industrial scale reliably? And, are these measurements useful?

Jan 1, 2006

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

Despite several methods (empirical, statistical and machine-learning tools) to calculate blast-induced ground vibration, it is not easy to predict and simulate blast vibration precisely under varying blasting loads and strata conditions due to complications in the blasting procedure. In this study, field blast data were simulated in Ansys software using explicit dynamics, and ground vibrations for 20 single-hole blasts were monitored. The densities of emulsion explosives were in the range of 0.9 to 1.15 g/cm3. In the laboratory, rock properties were determined from rock samples collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and density of the emulsion explosive were also determined and used in numerical analysis to know the ground vibrations at specific points. The results of ground vibrations predicted by the model were validated using field data.

By Michael Lenz

Predictive maintenance technologies including vibration analysis, tribology, infrared thermography, ultrasonic detection, and electrical measurements have been applied to large electric mining shovels. The predictive program was initiated on the P&H Model 2300 and 4100 electric shovels. The utilization of these technologies has shown the potential for improving electric mining shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition based planning of component replacement. Maintenance costs are minimized by focusing resources through condition based prioritization.

Feb 24, 1997

By Drinkwater DJ, Watsford RMS, Johnson NW, Munro PD

This paper describes the use of modelling and simulation techniques in the analysis and optimisation of grinding circuits at the Lead/Zinc Concentrator of Mount Isa Mines Limited.The objectives of the studies were to: -1. improve primary grinding circuit performance by reducing the production of -0.006 mm galena fines.2. maximise the fineness of grind in the second existing grinding power and pumping capacitie The study has shown that quantitative models can operations. The models described plant operation,,and simulated the effect of process changes on plant performanc The use of automated scanning electron microscope technology tcliberation characteristics of the major minerals in the Mount isa Lead/Li ore is also described.

Jan 1, 1985