Search Documents

By Wang Chen

COREX process is briefly introduced. A static model combining a set of mass and heat balance equations has been developed. Taking the specified inputs from the graphical user interfaces, the model is capable of calculating the consumption of raw materials and fluxes, the volume and composition of the slag and the volume and composition of the generator gas. The model enables the examination of the changes of materials and energy flows induced by the variations of operational parameters and raw materials chemical analysis. The model allows a detailed process analysis and adjustment of the plant operation and can thus be used to improve plant operation.

Jan 1, 2008

By D. E. Keeley

lntroduction Some years ago it was general practice in Canadian mines to use the best timber available, just as it was cut from the tree. Later, to prevent 'borers' from getting into the wood while stacked in the yard, the bark was peeled off, cleaned up carefully, and burned to eliminate a breeding ground for these and other destructive insects. This practice of good housekeeping also decreased the hazard from fire in scattered bark. A few years after damage by borers had been minimized, it became apparent that increased temperatures in the mines, occasioned by deepening operations, were being accompanied by rapid growth of fungus and by decay in timber underground, greatly shortening its life. In places on upper levels where the air temperature was below 50 deg. F., untreated timber retained a large proportion of its strength for ten or more years. In other places on these levels, however; its life was short and it developed much dry rot and merulius lacrymans. In these latter places and on lower levels in the mine where temperatures ranged from 50 to 60 deg. F., approximately, the wood became infested with extensive growths of this white fungus. This development was accompanied by the production of millions of spores. Spread of infection was due mainly to the transfer of spores from the warm lower levels to the cool upper horizons by upcasting ventilation currents. So serious did this become that about twenty years ago Lake Shore, Hollinger, and McIntyre Mines decided to investigate the use of wood preservatives and the plant necessary to treat timber.

Jan 1, 1949

By J. O. Down

St. Marys Cement Company operates two cement plants in Southern Ontario, Canada. The original plant, located at St. Marys, a town 20 miles north of London, Ontario, began operations in 1912. A second plant, located at Bowmanville, Ontario, 40 miles north east of Toronto, began operations in 1967. In June 1973, St. Marys Cement began feasibility studies of modernizing their wet process plant at St. Marys. Over its 61 year life, this plant had been expanded from 335 m. tons per day (375 s. tons per day) to 2000 tpd (2200 s. tons per day), with all the original equipment retired several years ago. The objectives of the feasibility study were to develop a conceptual plan for a dry process plant and to de-, fine the appropriate process method and equipment. This study proceded along four fundamental fronts: a) How could the clay raw material, a glacial till with up to 20% boulder content, be processed in dry form and beneficiated? b) Were the raw materials suitable for the most efficient form of dry process kiln, the 4-stage preheater? If a 4-stage preheater kiln is selected should it utilize a precalciner? c) What type of clinker cooler should be used? d) What environmental constraints would be imposed on this plant and how can they be reconciled with capital and operating limitations? During the feasibility stage, pilot plant work was done on two possible solutions to the clay problem, operating plants in Europe were visited and discussions held with kiln and mill vendors.

Jan 1, 1977

By R. M. Cox

Pneumatic coal loading and conveying systems provide alternative methods for the safe and efficient mining of the thin high-grade coal seams found in the Southern Appalachians. Pneumatic systems eliminate most of the health and safety hazards associated with the operation of conventional mining and haulage equipment in small low-coal mines by removing powered mobile equipment from the mine. Ventilation is also improved by the coincidental removal of gas and respirable dust from the mine by the operation of the pneumatic loading and conveying system. Other significant advantages of pneumatic coal recovery systems are relative simplicity, operating flexibility, low capital cost, quiet operations, environmental benefits, and ease of automation. The design considerations and field evaluations of experimental prototype pneumatic coal loading and conveying systems, installed and operated in small thin-seam mines, are presented in this report. In addition, fundamental design criteria and recommendations for the installation and operation of a variety of pneumatic coal loading and conveying systems are proposed, which offer alternative coal recovery systems that alleviate the serious health and safety concerns of current small mine operations.

Jan 1, 1999

By K. C. Sole, M. E. Mitshiabo

Although surfactants have proven to increase metal extraction by improving solution flow in porous media, these reagents have not been widely adopted in heap leaching operations because of potential incompatibilities with downstream processes that are subject to surface properties. The BASF leaching aid, LixTRA 118, was previously found to have no significant effect on post-leach operations. This study evaluated its performance in ores of different particle size distributions and the impact on acid consumption and metal recovery. Column leach studies, carried out on a copper oxide ore and mixed oxide–sulfide ore, showed that the effect of LixTRA 118 was more pronounced in ores with wider particle size distributions than in those with more uniformly sized particles. Solution percolation rates increased by up to 18% in the presence of leaching aid, and increased copper recovery and acid consumption. Improved wetting facilitated the kinetics of acid diffusion at macroand micropore level. There was no significant effect on iron recovery

Jan 1, 2023

By M. Mononen, J. Huuskonen, M. Vauhkonen, J. Kourunen, A. Lehikoinen

"A new approach to measure process conditions in flotation cells is presented. Real scale flotation cells in a Zinc circuit are imaged using Outotec LevelSense sensors based on electrical resistance tomography. The latest results from long period plant tests show that the sensors together with FrothControl analysis give new information that correlates well with other process parameters. The sensors can compensate for electrical contact contamination using an automatic calibration technique and they are basically maintenance free. The results indicate that using the LevelSense sensors and FrothControl solution, the process control and optimization can be done automatically, stabilizing and improving the metallurgical performance of the flotation process.INTRODUCTIONThe froth flotation process is widely used in mineral industry for the separation of minerals from low-grade ore slurry. Different property parameters of froth and slurry could be measured to monitor and control the flotation process: air bubble size distribution, flow dynamics, thickness of the froth bed, amount of solids in the froth, etc. Some techniques already exist that can be utilized in studying these important parameters on-line. Examples of the techniques are the high-speed video imaging, simple conductivity probes, ultrasound techniques, floats and pressure transducers (Maldonado et al., 2008). These techniques, however, often suffer from some limitations. For example, the video imaging only gives information from the surface of the froth, simple conductivity probes suffer from contamination and the floats may get stuck and therefore do not give reliable signal for process control and optimization."

Jan 1, 2013

By C. I. Pierce

The Bureau of Mines used an electrolytic tank model to investigate the response of guard electrodes of different dimensions under different simulated reservoir conditions. Sandstone disks from the Berea and Connellsville Formations were used as resistive beds in the model, and agar gel or water was used as conductive beds. In the experiments, bed thickness, hole diameter, mud resistivity, and bed resistivity were varied. The guard electrode is an excellent tool for determining true bed resistivity in the thin-bedded oil reservoirs of the Appalachian area. Vertical resolution and resistivity values are good when there is little or no invasion. Resistivity values are near true bed resistivity in beds thicker than about six hole diameters when the electrode-to-hole-diameter ratio is close to 1. However, low-resistivity muds cause false peaks to appear on the logs near bed boundaries in thick beds, and for resistive beds having a thickness approximately three to five times the hole diameter, apparent resistivities tend to be excessively high when mud resistivity is low.

Jan 1, 1966

The paper examines the value of very small-scale indigenous gold mining operations to developing countries. The paper looks particularly at this type of activity in two neighbouring countries, Papua New Guinea and the Philippines, considering technical, economic, social and environmental aspects.

Jan 1, 1990

The Carboniferous sedimentary rocks of southwestern Newfoundland merit investigation because of petroleum, salt and gypsum possibilities and indications of base metallization along the equivalent of the Horton-Windsor con-tact. In this paper, Lower Mississippian (Anguille) strata are divided into three formations: (1) the Cape John below, (2) the Snakes Bight and (3) the Seacliffs. A correlation between these formations and the Craignish, Strathlorne and Ainslie formations of the Horton group? in western Cape Breton Island is suggested. The criteria for the Anguille subdivision are essentially lithological, but preliminary study of included spore assemblages suggests more precise interformational correlations between Anguille and Horton sequences. The re-measured lower portion of the type section of the Codroy group is presented to define more clearly the stratigraphic position of numerous gypsum and limestone beds. Because of rapid facies changes within the Codroy group a simplified two-fold division into upper and lower units is proposed on the grounds of

Jan 1, 1964

By M Brady, O Salisbury, C Claassen, B Beamish, H Baxter

Monitoring for signs of elevated spontaneous combustion in the active goaf behind the longwall face is crucial for early intervention of any potential heating incidents. Typically, trigger action response plans (TARPs) are established at the start of longwall mining and often are only reviewed when triggers are activated frequently and become ‘nuisance alarms’, or in the worst case scenario after a heating event. Narrabri Mine has adopted a proactive approach of reviewing the longwall active goaf spontaneous combustion monitoring TARP at the commencement of each longwall block and prior to reaching a known ‘mylonite zone’ of crushed coal, which is associated with increased coal oxidation. The review is based on information recorded from the monitoring data of the previous longwall blocks as well as interpretation of relevant spontaneous combustion propensity results for the coal. This has resulted in the mine implementing a zoned TARP approach for each longwall block covering both the longwall retreat through normal undisturbed coal and the zone where the goaf is influenced by the increased coal oxidation associated with the mylonite coal. The consequence of this approach is that it has removed the issue of having nuisance triggers being activated during mining through a known increased oxidation zone, while maintaining a high awareness of indicators of spontaneous combustion.CITATION:Baxter, H, Claassen, C, Salisbury, O, Brady, M and Beamish, B, 2015. Implementation of a zoned trigger action response plan associated with changing mine conditions at Narrabri Mine, in Proceedings The Australian Mine Ventilation Conference, pp 113–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By J. Noll, D. Yantek, J. Organiscak

The Office of Mine Safety and Health Research of the U.S. National Institute for Occupational Safety and Health (NIOSH OMSHR) conducted laboratory testing of a self-tramming, remotely controlled mobile Dry Scrubber (DS) that J.H. Fletcher and Co. developed under a contract with NIOSH OMSHR to reduce the exposure of miners to airborne dust. The scrubber was found to average greater than 95 percent dust removal efficiency with disposable filters, and 88 and 90 percent, respectively, with optional washable filters in their prewash and post-wash test conditions. Although the washable filters can be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-min washing period. The scrubber’s velocity-pressure-regulated variablefrequency- drive fan maintained relatively consistent airflow near the targeted 1.42 and 4.25 m3/s (3,000 and 9,000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60-Hz fan motor frequency or horsepower rating at 2,610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8,420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the scrubber showed that the outlet side of the scrubber was noisier, and the loaded filters increased sound levels compared with clean filters at the same airflow quantities. With loaded filters, the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6,000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level — under Title 30 Code of Federal Regulations Part 62.101— of 90 dB(A) at or below this airflow quantity. The scrubber’s washable filters were not used during field-testing because of their lower respirable dust removal efficiency and the airborne dust generated by filter washing. Field-testing the scrubber with disposable filters at two underground coal mine sections showed that it could clean a portion of the section return air and provide dust reduction of about 50 percent at the face area downstream of the continuous-miner operation.

Jan 1, 2016

By James P. Rider, Charles D. Taylor, Edward D. Thimons

Research was conducted to investigate how ventilation of a mining face is affected when scrubber flow is greater or less than intake flow. Tests were conducted in a full-scale surface test gallery built to simulate a mining entry with a continuous mining ma- chine at the face. Methane gas was released at constant flow at the mining face. Gas measurements taken at six locations near the face were used to evaluate how well the face was being ventilated. Increasing scrubber flow resulted in lower methane levels even when scrubber flow was much greater than intake flow.

By G. S. Rice

This paper describes preliminary tests at the Bureau's Experimental Mine to determine, under conditions that may prevail in a bituminous coal-mine heading, how small a quantity of fire damp may bring coal-dust into suspension and ignite it. The results show that the explosion of as little as 150 cubic feet of an explosive mixture of gas and air containing 9 per cent natural gas may start a disastrous explosion of coal-dust. This is a very small volume, of gas, to cause such a result. Let us suppose that this amount of explosive mixture, as at the face of an entry which was 10 feet wide and the face was overcut to a depth of 6 feet and an upper layer of coal 2.5 feet thick had been removed, the recess so made would have a volume of 150 cubic feet. Furthermore, only 13 cubic feet of pure methane is needed in thin volume to produce this 9 per cent explosive mixture.

Jan 1, 1930

By J. L. Miller, R. W. Burns

This paper sets out the various phases of bringing a merchant bar mill into operation from feasibility consideration through financing, design and scheduling to completion.

Jan 1, 1967

By W. B. Morrey

This paper deals with the development of the new cap-sensitive slurry explosives. The history and special features of these explosives are outlined, and recent field trials are described.

Jan 1, 1973

By J. L. Havenga, L. J. van der Walt, J. T. Nel

"SynopsisThe development of plasma technology at Necsa started in the early 1980s, when the applicability of high-temperature plasmas in the nuclear fuel cycle was investigated. Since 1995, this plasma expertise has expanded to other industrial applications, for example mineral beneficiation, nanotechnology, fluorocarbon production and waste treatment, all of which are also of relevance to the nuclear industry.Necsa has demonstrated the manufacture of plasma-dissociated zircon, zirconium metal powder, carbon nanotubes, silicon carbide (SiC), zirconium carbide (ZrC) and boron carbide (B4C) at the laboratory and pilot plant scale. These materials are commonly used in the nuclear industry. Zirconium alloys are used as fuel cladding material for nuclear fuel assemblies.Necsa manufactured the monomer tetrafluoroethylene (TFE), using 150 and 450 kW DC plasma systems, from which the polymer polytetrafluoroethylene (PTFE) was synthesized for use in filters and as seals in nuclear plants. With the nuclear renaissance at hand, it was demonstrated that plasma technology can be used to produce hydrofluoric acid (HF), which is used in the manufacture of fluorine gas (F2) for the production of uranium hexafluoride (UF6) directly from the mineral calcium fluoride (CaF2) without the use of sulphuric acid as in the conventional process. The recovery of valuable uranium from nuclear waste such as filters, oils, and solids with plasma processes will also be discussed. The destruction of low-level nuclear waste by a plasma gasification system can reduce the volume of this waste by several orders in magnitude, resulting in huge savings in the storage costs. Another product of plasma technology is the encapsulation process for nuclear waste and the production of vitrified product, which could be used as filler material for medium-level nuclear waste.IntroductionDuring the 1980s, a plasma research and development programme was launched at the erstwhile Uranium Enrichment Corporation of South Africa (UCOR) at Valindaba outside Pretoria. The main purpose of this programme was to develop alternative and more economical processes for the processing and manufacturing of uranium compounds used in the nuclear fuel cycle. The conversion of UO2 (as received from uranium mines) to UF6, which is needed for enrichment, conventionally involves several laborious, expensive, chemical processing steps. Plasma processes can eliminate several of the intermediate steps. Enriched UF6 is converted to UO2, which is pressed into pellets that are used in nuclear power plants. Plasma technology could also be used in a modified and optimized conversion process."

Jan 1, 2015

By George L. Gates

The Bureau of Mines developed a rapid instrumental method of analyzing oil well scales containing primarily barium sulfate. After removal of oil and water by carbon disulfide) the scale was dissolved in strong hydrochloric acid. The cations, barium, calcium, strontium, magnesium, and iron, were determined with the flame photometer using the method of additions. Sulfate was deter-mined colorimetrically after separation by selective adsorption on an alumina column. Phosphate was determined colorimetrically and carbonate titrimetrically. The method was reasonably accurate, although iron and magnesium were found to have mutual interference.

Jan 1, 1965

By A. A. Goss

We investigate the relationship between corporate financial performance (CFP) and environmental and social performance (CSP) in a sample (n=165) of large, publicly traded U.S. mining and oil and gas firms. Using optimally scaled principal components analysis to generate aggregate measures of CSP strengths and concerns, we find higher concerns are related to higher volatility of unexpected earnings and discount rates. Furthermore, these earnings shocks are more likely to be negative as concerns increase. Decomposing this relationship shows that negative environmental performance dominates proactive environmental management as a driver of unexpected earnings, but proactive community efforts increase the magnitude of earnings shocks. We document some evidence of the strategic use of CSR, with those firms that have greater risk investing more proactively in CSR.

Aug 1, 2013

By John W. Ahlrichs

Microscope, electron microprobe and x-ray diffraction have been used to provide quantitative evaluation of products from the mill, smelter, refinery and other metallurgical processes. Phase compositions and their quantities are necessary for an adequate understanding of the various products obtained throughout an operation and in laboratory testing. By careful evaluation, important information can be gained in improving recoveries and increasing grades at various stages of processing. Four case histories are discussed in this paper. Quantitative microscopic counting techniques are applied to mill products to determine degrees of locking and liberation of the economic minerals. Rapid, but accurate evaluation aids the metallurgist to develop or improve the grinding and flotation circuits. In the smelter, the identification and quantification of the phases are important for predicting reaction mechanisms and kinetic trends. Mineralogic techniques have been applied to conventional smelter products, and to those obtained in laboratory tests for newly developed innovations to smelting. Small, but important, values of gold occurrences in ore are difficult to determine. Evaluation of gold usually requires special separations into various mineral concentrates, followed by assays and mineralogic determinations of the products. Numerous occurrences of solid solution constituents can be treated as by-products, but often they are deleterious to metallurgical treatment. Most solid solution problems can be unraveled by the mineralogist's tools.

Jan 1, 1981

By Ahmad Ghahreman, Lin Li

Silver and cupric ions have been proven to play the roles of catalysts to promote the oxidation kinetics of chalcopyrite in acid solution. In this study, the interaction between silver ions and cupric ions during ferric leaching of chalcopyrite in sulfuric acid solution has been investigated. The electrochemical study by Tafel analysis showed a significant boost of dissolution rate for chalcopyrite dissolution in Fe3+- Cu2+ containing sulfuric acid solution after Ag+ was added in the solution. For 10 ppm Ag addition, the dissolution rate of chalcopyrite increased to 7.94 ×10-6 A/cm2 from 3.2 ×10-7 A/cm2, when Ag+ was absent. On the other hand, the effect of Cu2+ on the dissolution of chalcopyrite in Fe3+-Ag+ containing sulfuric acid solution was not obvious from electrochemical measurements. The chalcopyrite leaching tests in different acid solutions showed that silver addition had an obvious catalytic effect on promoting chalcopyrite dissolution. Comparing the leaching rates of chalcopyrite leached in Fe3+ containing, Fe3+-Ag+ containing, Fe3+-Cu2+ containing and Fe3+-Cu2+-Ag+ containing sulfuric acid solutions, it was found in Ag+-Fe3+-Cu2+ containing sulfuric acid solution, the leaching rate was highest among all the aqueous acid systems. Further leaching tests suggested that with increase of the Ag+ concentration from 0 to 20 ppm, the leaching rate of chalcopyrite in Ag+-Fe3+-Cu2+ containing sulfuric acid solution also increased and reached 57.62% with 20 ppm Ag+ addition after 24 h. INTRODUCTION Chalcopyrite is the most important copper mineral in copper hydrometallurgy and it accounts for nearly 80% of the universal copper resource (Olvera, Rebolledo, Mora, Dixon, & Asselin, 2018). The hydrometallurgy of chalcopyrite has been intensively studied with emphasis on solving the slow dissolution kinetics of chalcopyrite in acid environment. A variety of aqueous systems, such as sulfate (Hiroyoshi, Miki, Hirajima, & Tsunekawa, 2001), chlorides (Liu, Chen, & Yang, 2017), and ammonia (Hua et al., 2018) have been studied to improve copper leaching. From another perspective, chalcopyrite leaching studies have indicated that the mechanism of chalcopyrite dissolution in acid solution is essentially electrochemical (Li, Kawashima, Li, Chandra, & Gerson, 2013). Therefore, extensive studies have recently been carried out to explain the dissolution kinetics of chalcopyrite in different media by various electrochemical techniques.

Jan 1, 2019