Search Documents

By Renato S. Costa, Afonso H. Martins, Flávia D. Mendes

"This paper presents some important aspects regarding the ion exchange treatment of an Ni and Co sulphate acidic liquor using chelating resins. Chelating resins possessing iminodiacetic or bis-picolylamine functional groups were compared in terms of nickel and cobalt recovery. The experimental resin with bispicolylamine functionalities (Dowex M4195) was evaluated with respect to Ni and Co uptake, and compared with Rohm &Haas commercial chelating iminodiacetate acid resin. The Rohm & Haas chelating resin, Amberlite IRC 748, with its weakly acidic groups, did not work in acidic solution but exhibited good results at pH 4 and above. The resin that efficiently removed metals from high acidic solutions was the bis-picolylamine resin. Maximum nickel uptake values ranged between 85 g and 112 g Ni per Kg of resin.The experimental part dealt with the working conditions, resin characteristics and the influence upon the resin maximum exchange capacity of the following factors: nickel concentration, temperature, pH and resin-to- solution ratio. Based on the experimental data obtained, it has been proposed a innovative technological treatment."

Jan 1, 2003

By K Ionkov

The oolitic iron ore reserves in Lisakovsky, North Kazakhstan represent quite a challenging deposit both from a technological and from a resource point of view. The difficulties in processing such types of ore are connected with the extremely fine dissemination of phosphorus and gangue minerals inside the oolitic formations. The goethite crystals are cemented in their structure by aluminosilicates with quartz and other gangue minerals and dissemination is so fine that they are not separable by physical methods. The laboratory tests performed for dephosphorisation show that the combination of alkaline roasting followed by low intensity magnetic separation and acid leaching enables the obtaining of high grade iron concentrate. The magnetic separation performed ahead of leaching is effi cient as a means of buffering the high pH by washing out the soluble salts and the excess of base and after leaching facilitates the removal of secondary liberated gangue minerals in the non-magnetic fraction. As a consequence, phosphorous content is dropped to a more acceptable level for the ferrous metallurgy and iron grade and recovery reach 61.6 and 80.8 per cent respectively.

Jul 11, 2011

By Qingchun Yu, Bin Yang, Yong Deng, Heng Xiong, Fei Wang, Minxiu Chen

"Metal aluminum produced by non-electrolysis process received much attention due to its lower energy consumption. In this paper, carbothermic reduction and carbothermic-chlorination of alumina in normal pressure and vacuum were studied. The products were examined by means of XRD, EDS and SEM. During the carbothermic reduction process using carbon reductant in normal pressure, no metal aluminum was found. However, when coal was used as reductant, a mixture containing metallic aluminum, A14C3, and silicon was obtained, but metallic aluminum couldn't be separated from the mixture. During the carbothermic-chlorination process in vacuum, Al404C and Al4C3 were produced by the reaction between alumina and carbon, and Al Ch gas reacted with Al404C and Al4C3 to produce Al Cl gas. Metallic aluminum was produced due to the disproportionation of A!Cl gas and condensed on the collecting plate. Meanwhile, the initial temperature of carbothermic reduction of alumina reduced in vacuum compared with that in normal pressure.IntroductionIndustrial production of primary aluminum is carried out in alumina cell by the so-called Hall- Heroult process, necessitating the use of very high currents of low voltage. The alumina from which metallic aluminum is gained must be chemically pure, otherwise impure metal results. The main drawbacks of the electrolytic production are its very high energy consumption, the release ofperfluorocarbons, and the high specific C02 emissions [1]. During the past years, there were a lot of attempts to produce metallic aluminum by carbothermic reduction of A1203 [2, 3]. Cox [4] determined the vapor pressure over the A1203-C system and performed X-ray diffraction analysis of condensed products. It was demonstrated that an increase in the carbon content in the system leaded to the sequence of transitions: A1203~Al404C~A1zoc~A14C3 ~AI [5]. In any carbothermic reduction process for aluminum, extremely high temperatures (2000 °C ) were required [6]. In spite of considerable effort, the carbothermic reduction of alumina to aluminum remains a formidable technical challenge, due to the high temperatures required, and to the formation of aluminum carbide and oxycarbide byproducts [7]."

Jan 1, 2013

By Heinz W. Sternberg

A method for the electrochemical reduction of the benzene ring was developed and applied to the electrochemical reduction of coal. Successive electrochemical reductions of a vitrain from low-volatile bituminous coal in ethylenediamine saturated with lithium chloride resulted in the addition of 53 hydrogens per 100 carbon atoms. Ultimate analyses and pyridine solubility of the vitrain recovered after each reduction showed that hydrogen added at the beginning has a much greater effect on solubility than hydrogen added at a later stage. Surprisingly, the removal of sulfur from the vitrain takes place only after the more reactive aromatic rings are reduced. Nuclear magnetic resonance analysis and average molecular weight determination of the extracts of the reduced vitrain samples, representing about 18 percent of the vitrain, showed that these fractions had 95 percent of their hydrogen content on saturated carbon atoms and an average molecular weight of 800 to 900. A study of the effect of operating variables on current efficiency showed that current efficiency is highest with aluminum as cathode material and with lithium chloride as electrolyte. A substantial increase in current efficiency of difficulty reducible olefinic double bonds was achieved by adding a proton donor. This result is significant in connection with the electrochemical reduction of coal which proceeds from readily reducible aromatic double bonds to difficultly reducible isolated double bonds. It is proposed that reduction is achieved by electrolytically generated and subsequently solvated electrons and hence does not require prior adsorption of the substrate at the electrode surface. This offers a distinct advantage for electrolytic reduction of sparingly or insoluble substrates such as coal.

Jan 1, 1967

By B. S. Graves

Deep well disposal of selected industrial wastes has been proved feasible and acceptable in the New Orleans area by several industries including Shell Oil Company's Norco Refinery and Chemical Plant where three of the six successful disposal wells in this area are operating. Well design and procedures for restoration of capacity are based, in most cases, on the principles of brine injection developed by oil producers in South Louisiana. Geological formations in the Gulf Coast area are suited to this type of injection because receiving strata are porous, isolated from sources of potable water and their water is compatible with the liquid wastes to be injected. This method of disposal is a simple, complete and economical solution to the problems presented by certain hard to treat wastes.

Jan 1, 1964

By Kurt R. P Petersen

This paper discusses the current approaches to modelling the DMS cyclone within the De Beers group. Current efforts are split into short term value-adding process understanding and longer term semi-fundamental analysis of separation mechanisms. To date, the basic applied approach has yielded significant value to the group, enabling operators to focus on simple diagnostic measures to control their process. The more involved modelling approach has given rise to a new understanding of the separation field, in particular that the high density gradients within a cyclone are highly localised, indicating that separation of medium to heavy density material takes place low in the cone. The model has proven to be conceptually robust, but still requires further development and validation to become a complete modelling and simulation tool for De Beers.

Jan 1, 2006

By Jacob Schoder

This is one of a series of papers published by the Bureau of Mines on mining and milling methods and costs. The Tennessee-Schuylkill Corporation, Chloride, Ariz., mines and mills a lead-zinc ore containing gold, silver, and a small amount of copper. The mill products are lead and zinc concentrates that are shipped to smelters. The company was the second largest producer of lead and zinc in Arizona in 1937 and was seventh in gold production. Operations discussed are those being conducted at the mine in October 1938 and are representative of the complete operating period from 1936 to date.

Jan 1, 1939

By A. N. Fried

With the growing importance of fluid injection in recent years, the petroleum industry has been investigating and field- testing a variety of new methods designed to modify the physical properties of reservoir oil to improve the efficiency of gas and water injection. These procedures include condensing-gas drive, LPG (liquefied petroleum gas) injection, alcohol-slug process, high-pressure-gas displacement, detergent-solution flooding, and in situ combustion (30, 37).3 A new and different method to increase the effectiveness of gas and water injection has been tested by the Bureau of Mines, Consideration of both fundamental and practical factors that operate to limit the oil recovery attain- able by conventional oil-displacement mechanisms led to the concept of a displacement mechanism called the foam-drive method. This report describes the experimental study that tested this concept in the laboratory.

Jan 1, 1961

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"Reduction of combustion-emitted greenhouse gases, which are associated with global warming, may be achieved by use of CO2-neutral alternative fuels, such as bio-ethanol. Distillers Dried Grains with Solubles (DDGS) are the main co-products of the com-grain-based ethanol industries. In 2009, the North American production of ethanol from com was about 38 billion liters, which generated approximately 31.5 million tons of DDGS. Samples of DDGS were pyrolysed at temperatures of 600-1000 °C in a two-stage laminar-flow horizontal furnace, and a catalyst system was used to synthesize nanomaterials. This work presents a microstructural characterization of these nanomaterials by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Results showed that the nanomaterials produced from pyrolysis of DDGS were in the form of long, entangled, rope-like structures with rugged walls, lengths in the tens of microns, and axially non-uniform diameters in the range of 100-300 nm.IntroductionThe interest in ethanol has increased considerably worldwide due to the necessity of finding renewable and cleaner energy resources [1, 2]. According to the Renewable Fuels Association (RF A), the world ethanol production in 2008 was approximately 65.7 billion liters (17.3 billion gallons), which figure represented a 24% increase in the production over that in the previous year [3]. The major producers of ethanol are the USA and Brazil, which together account for 90% of world production. The main feedstock for ethanol in USA is com grain, whereas sugarcane predominates in Brazil [2-4]."

Jan 1, 2011

By Arne Landsberg

Accessory metals, although valuable resources, present possible environmental concern in the smelting of base metals. The Bureau of Mines, U.S. Department of the Interior, has undertaken research to define the chemistry involving these metals. Arsenic in copper smelting is the first to be investigated. Roasting, the first step in many copper smelters, was chosen for initial investigation because of the potential for arsenic removal in this primary process. Simple, static-bed, vaporization experiments were devised to obtain the data in this study. Ancillary transpiration and mass spectrometry were also used to delineate conditions necessary for arsenic volatilization from a roaster feed. For nearly complete arsenic removal, a temperature of 650°-700° C, a reducing atmosphere including carbon monoxide, and a source of sulfur were found to be essential.

Jan 1, 1980

By Peter G. Mason

Over the last 15 years numerous Pressure Oxidation and Pressure Leach plants have been installed throughout the world. The technology is no longer regarded with awe and trepidation as plants designed to treat a wide range of feedstocks continue to be successfully brought on line. Important aspects of the design of such plants include feed preparation, slurry pumping, heating and heat recovery, pressure control and let-down, vessel design, safety and provision of associated services.

Jan 1, 1999

By S. K. Shaha, W. Kasprzak, D. L. Chen, J. Friedman, F. Czerwinski

The role of solutionizing conditions within the T6 heat treatment of the cast Al-Si-Cu-Mg alloy with micro-additions of Zr-Ti-V was assessed in terms of their influence on microstructure and mechanical properties. As a solution treatment, a single step process at 485 and 510oC and a two-step process at 510 and 525oC for varying time intervals from 0.5 to 9 h, were examined. In all cases, solution treatment was followed by isothermal aging at 150oC for 100 h. The microstructural analysis showed that the solution treatment changed the eutectic silicon morphology from needle-like, present after casting, to spherical shape in the T6 state and that the extent of changes was strongly influenced by temperature and time. The Cu- and Mg-rich phases completely dissolved during solution treatment while the Fe-containing phase, Al8Si6Mg3Fe, remained partially in the microstructure. The Ti, V and Zr containing phases, Al13Si2Ti3Zr and Al3Si26FeTiV10, present in as-cast state, were partially dissolved during solution treatment, reducing their size by 10 - 48%. The studied alloy reached the maximum ultimate tensile strength of 335 MPa and yield stress of 303 MPa for two-step solutionizing with a total time of 4.5 h. It is concluded that the two-step solution treatment resulted in higher tensile properties than the single-step process.

Jan 1, 2015

By De-qing Zhu, Jian Pan, Tie-jun Chun, Dong Chen, Yu Cui

"A study of processing pyrite cinder and metallurgical slag using “one step” technology in strand grate - rotary kiln is presented, which aims to efficiently recover the valuable metals of iron, lead, zinc and copper. The effect of chloridizing roasting parameters including roasting time and temperature on the removal rates of nonferrous metals was investigated. It is shown that copper and zinc are difficult to remove and lead is removed more easily. The preheated pellets were reduced in a rotary kiln, where zinc and lead can be removed easily and high iron grade and good metallurgical performance prereduced pellets can be obtained. Furthermore, the chlorination and the reduction mechanisms of copper, lead and zinc are discussed. It is revealed that the phases of copper, lead and zinc in slag are complex and ferrite and silicate of metals are difficult to remove.IntroductionAs two kinds of significant secondary resources, metallurgical slag and pyrite cinder contain not only abundant iron but also considerable copper, lead, zinc and so on. Several tens of millions of tons of metallurgical slag and pyrite cinder are discharged in nonferrous metal and chemical industries annually in China [1, 2]. In addition, the accumulated waste slag in storage is more than one hundred million tons, which not only occupies much land but also pollutes the environment [3]. However, because the metallurgical slag and pyrite cinder are treated by high temperature processing, the properties are distinctly different from the properties of natural ores, and iron is in close association with copper, lead and zinc. So, metallurgical slag and pyrite cinder are difficult to efficiently utilize and only a small amount is used as additives in cement, paving, brickmaking and auxiliary additives [4-7]."

Jan 1, 2011

By Klaus Rabensteiner, Klaus Chmelina

"INTRODUCTION Urban tunneling is often related with special geotechnical risks. Typical causes are difficult (hydro)geological conditions, a very low overburden and the presence of critical and vulnerable (infra)structures in the influence zone of the construction (e.g. existing tunnels, roads and pavements, sewer pipes, gas and power lines, landmarked buildings, historic monuments). To manage these risks appropriately, an early detection and warning of unexpected behavior of the affected geotechnical objects ground and tunnel, as well as existing structures are mandatory. To accomplish this, the design and execution of a dense geotechnical monitoring program is of high importance. In more detail, this means specifying and performing a systematic and continuous acquisition, processing and analysis of monitoring data to support decision making. In recent years the development of new automatic sensors and (wireless) data transfer techniques and the general trend towards an automatic acquisition of monitoring data has led to an enormous increase of data production frequencies and volumes. In order to handle this data explosion efficiently, information systems and geo-databases have been developed and used successfully in many projects. They represent IT tools that support the different tasks of a given geotechnical monitoring program including data acquisition, transfer, check, processing, backup, analysis, distribution, reporting and, last but not least, alarming. Meanwhile, some tools already have developed the capability to connect to other theme-specific databases used in the project and, thus, serve as a central data management system for all kind of digital data produced. This makes possible the implementation of further useful functions and services supporting tunneling tasks such as machine control, tunnel simulation, geological prediction, process optimization, etc. where data from different engineering disciplines must be combined and processed in an integrated way. In the following chapters our aim is to describe how monitoring data management, geotechnical monitoring, alarming and reporting are organized and technically implemented at the metro project Cityringen in Copenhagen (Denmark). We want to highlight the specific role and tasks of the used tunnel information system in the project, and particularly inform on the most relevant challenges."

Jan 1, 2016

By Scott D. Neely, Donald R. Clark

"An existing landslide located at the southeast corner of the Telluride Regional Airport has been in an active state of failure for several years. The presence of the landslide has represented an on-going liability for the Airport, the Federal Aviation Administration and the Colorado Department of Transportation. A catastrophic failure of this landslide occurring in a manner similar to that which occurred at the Airport in 1987 has posed an on-going threat to closing Colorado State Highway 145 south and below the slide area. The existing landslide has been characterized as a series of multiple failed block areas located downhill of the airport runway that have occurred in severely weathered Mancos Shale.A total of 12 alternatives were evaluated to mitigate the landslide, including the preferred alternatives of either partial or total landslide removal. However, prior development has left essentially no place on the airport property that would allow for the disposal of the landslide debris for either the total or partial removal alternatives, and the closest off-site disposal area was approximately 40 miles from the site. As a result, in-situ stabilization of the landslide, including a primary system of isolated tie-back anchor plates with strand anchors, and a secondary system of high strength steel mesh and intermediate anchors was selected for the ultimate design of the project to stabilize the landslide in place.For design purposes, geotechnical characterization of the slide area was accomplished through geological mapping, conventional borehole exploration and geophysics using multiple electrical resistivity. The paper discusses the design process utilized and the unique challenges faced one-third of the way through construction when discovery of a survey error required redesign of the entire landslide mass stabilization system using the prefabricated anchors that had already been delivered to the project.INTRODUCTIONTelluride Colorado is located at the toe of the Colorado Rocky Mountains on the western slope. The Telluride Regional Airport is located on Deep Creek Mesa about 5 miles west of the town of Telluride.The landslide is located at the southeast corner of the airport just below an abandoned portion of the quarry access road on a south facing slope. The quarry access road is located below the elevation of the runway and outside the elk fence that surrounds the air traffic area of the airport property. Since the reconstruction of the runway, the access road to the quarry and the construction access road for the reconstruction of the airport runway and safety area were rerouted to stable ground north of the previous access road location and off of the head scarp of the landslide."

Jan 1, 2015

By Dan Ifrim, Andre Solecki

Tunneling could be a major challenge to tunneling contractors as tunneling operations can be seriously affected by the Tunnel Boring Machine (TBM) performance. Specifying the appropriate TBM methodology, selection of systems and features, is critical for managing tunnel risks and contribute to successful tunneling project. The paper analyzes tunneling records from the recently completed City of Toronto’s Ashbridges Bay Treatment Outfall tunnel project and underlines the righteous selection of the TBM type and associated TBM systems in achieving good advance rates during tunnelling and managing project risks. The paper intends to draw attention of a few aspects of TBM technical specification importance and highlight the lessons learned from this process.

Jun 13, 2023

By Mônica Aline Magalhães Gurgel

A crescente preocupação da indústria automobilística com questões ambientais e com a segurança do condutor e passageiros, fez com que o setor siderúrgico desenvolvesse aços com maior valor tecnológico, entre eles surgiu os aços avançados de alta resistência, onde encontra-se o “Dual Phase” (DP) utilizado nesse estudo, que é caracterizado por uma microestrutura associada a uma matriz ferrítica com ilhas dispersas de martensita. Neste trabalho utilizou-se amostras de um aço baixo C e Mn, com micro adição de Nb e Mo, em desenvolvimento, onde se propôs uma avaliação das propriedades mecânicas através de um Ultramicrodurômetro, as amostras extraídas após a laminação a frio seguiram para o recozimento intercrítico, em escala laboratorial, com auxílio de forno Mufla e um equipamento de análise termomecânica (TMA), com 7 temperaturas de encharque distintas e subsequente resfriamento com patamar isotérmico a 600°C por 20 minutos. Onde observou-se que a utilização do ultramicrodurômetro instrumentado mostrou ser uma ferramenta com grande potencial para a avaliação almejada.

Aug 17, 2017

By H. R. Bullis

Lupin is located on the shores of Contwoyto Lake at lat. 65° 48'N, Long. 111° 15'W and lies about 80 kilometers south of the Arctic Circle. Since start up in 1982 the mine has produced over 2.15 million ounces of gold from 6.66 million tonnes of ore grading 10.63 gm/tonne. Total remaining reserves at 1993 year end were 5.1 million tonnes at a grade of 9.11 gm/tonne (1.65 million ounces). This is sufficient for 7 -8 years at the present annual production rate of about 200,000 ounces. The Centre and West Zones of the deposit are open to depth. The deposit is in an Archean metaturbidite sequence of the Contwoyto Formation, which has been mapped as part of the Yellowknife Supergroup of supracrustal metasedimentary and metavolcanic rocks making up part of the Slave Geologic Province. These rocks have been subjected to regionar and contact metamorphism and to several phases of deformation. Six stages of Archean plutonism have been identified and all Archean rocks have been cut by Proterozoic diabase dyke swarms. Gold mineralization in the Lupin deposit is commonly fine grained and associated with pyrrhotite and arsenopyrite in amphibolitic banded iron formation. The gold-bearing portions of the host iron formations are characterized by the presence of multiple quartz veins and the pervasive replacement of grunerite by hornblende. In sparsely mineralized portions of the host iron formation, zoning of sulfides about quartz veins is clearly seen with the arsenopyrite halo being more restricted around the veins than the pyrrhotite halo. In well mineralized portions, quartz vein densities approach one vein per metre along strike. In these areas pyrrhotite distribution in the iron formation is more pervasive and the rock takes on the appearance of a banded sulphide rock.

Jan 1, 1995

By John Hardy

The performance of five dense-medium washers was evaluated in four preparation plants. Three of the plants were making a two-product separation that produced a clean coal and a refuse; one plant employed dense-medium vessels in series to effect a primary and a secondary separation. The secondary drum-type washer produced a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam generation. The sharpness-of-separation was excellent for all four primary separations and the secondary separation.

Jan 1, 1966

By John M. Gomes

A two-phase molten halide-silicate technique for extracting tungstic oxide (WO3) from scheelite (CaW04) and wolframite [(Fe, Mn)W04] was investigated. The halide phase extracted over 99 percent of the was, whereas the lower silicate phase retained about 90 percent of the calcium, iron, or manganese oxides. The most efficient extraction and separation of tungsten from scheelite was accomplished at 1,080° C in a molten system containing, in mole-percent, 9 calcium tungstate (CaW04), 42 sodium chloride (NaCl), 28 sodium fluoride (NaF), 17 sodium metasilicate (Na2SiO3), and 4 alumina (Al2O3). Wolframite was also treated at 1,0800°C; the molten system contained, in mole-percent, 11 (Fe, Mn)W04, 74 NaCl, and 15 Na2 SiO3.

Jan 1, 1968