Search Documents

By Kim Le Roux

Cemented paste backfill (CPB) is a relatively new material that is increasingly being used in open stope mining across the world. The advantages offered by this high density tailings backfill include: a lower total cost associated with backfill placement, reduction of excess water underground; and the elimination of the need to process the tailings prior to placement. However, almost all backfill design is based on the performance of laboratory prepared samples since it is difficult to obtain undisturbed samples and conduct in situ testing due to the lack of access to backfilled stopes and the safety concerns in accessible areas. The logistical problems associated with conducting in situ testing and obtaining undisturbed samples of cemented paste backfill (CPB) has lead to the reliance in the mining industry on performance data obtained from laboratory prepared CPB samples. The degree to which these laboratory prepared samples represent the actual in situ condition is not well defined, partly because the influence of the mixing, transport and placement process on the material properties it is not well understood. Therefore, there is a need in the industry to understand how the material properties and hence the performance of the laboratory prepared CPB compares with in situ material. This paper reports the findings of an investigation into the in situ properties of CPB at a gold mine in Northern Ontario. A combination of in situ and laboratory testing, conducted on undisturbed samples, was used to quantify the in situ properties and performance of the CPB. These results were then compared to those of a laboratory based investigation of the same CPB. It is evident from this investigation that the bulk properties of the in situ CPB are different from those of the laboratory prepared CPB. The most significant observed differences are that the in situ CPB has a higher void ratio and a lower degree of saturation than the laboratory prepared material. The implication of these differences on the stability and performance of the CPB will also be explored in this paper. 1

May 1, 2002

By Yushuai Xian, Youjun Tao, Fangyuan Ma

This study compared particle size distribution and density distribution of crushed products for waste printed circuit boards (WPCBs) before and after heat treatment. The crushing process for heat-treated WPCBs is a selective crushing process; more metal is concentrated in the coarse particle range of 1.0–0.5 mm and high density range of 2.8–2.96 g/cm3. WPCBs were separated using the Falcon separator to recycle useful metals. The Box-Behnken module of Design-Expert was used to obtain optimal separation parameters, namely, rotational frequency of 25 Hz, recoil water pressure of 0.025 Mpa and feed speed of 34 ml/s. On this basis, the separation indexes for WPCBs with and without heat treatment were compared. Experimental results show that the recovery effect is better for heat-treatedWPCBs than for thosewithout heat treatment. Comparedwith the non-heattreatedWPCBs, the product grade of heat-treated WPCBs is 1.95% higher, and its recovery is improved by about 14%. Finally, characteristics ofWPCBs before and after heat treatment were analyzed on the basis of stress experiments and scanning electron microscopy (SEM), respectively. Results of mechanical characterization indicate that the stress experiment for non-heat-treated WPCBs has a maximumpressure load of 212 N and displacement of 20mm, but heat-treatedWPCBs only need 140 N stress and 14 mm displacement. SEM shows that copper foil and fiberglass cloth are deformed in different directions and sizes after heat treatment to form gaps, which promote liberation of copper foil and fiberglass cloth.

Sep 10, 2020

By Gregory E. Smith

"Tensionable headed roof bolt systems are common in the U.S. mining industry. In the last 15 years or so, they have made a comeback as a hybrid system where a mechanical anchor is used in conjunction with resin. When such a system is used, it is common to use a spherical washer to comply with the requirements of 30 CFR Part 75.204(f)(8). This standard requires an angle-compensating device be used in installations where the bearing plate is offset from the roof bolt axis by an angle greater than five degrees. This paper evaluates system performance of four different traditional angle-compensating device/plate combinations including a new patented extruded plate/extruded washer system that improves overall load capacity and stretch.INTRODUCTIONA large western U.S. underground coal mine was using a fully grouted headed rebar system as their primary support. They had developed their component specifications over many years of working with suppliers to improve and optimize these components to integrate well as a system. As shown in Figure 1, the components included a patented 7 /8"" -diameter Grade 60 headed rebar bolt with a flange capable of full bar load (Walker, 2009) and a patented 8 in x 8 in Grade 3 extruded hole bearing plate manufactured by DieMatic Corporation.The mine decided to pursue a fully grouted tensionable system using a mechanical anchor as the tensioning device. Their primary goal was to eliminate the need for the roof bolt operator to secure (hold) the bolt during resin set time. An additional benefit was the increased initial tension on the bolt. To comply with the requirements of 30 CFR Part 75.204(f)(8), regarding tensioned roof bolts, they were required to include an angle-compensating device because a share of the bolt population would be installed at angles greater than five degrees from the perpendicular to the bearing plate. Also, to improve cycle time and torque/tension consistency, the mine desired to have the washers and anchors assembled at the factory. This required the use of a bearing plate with a center hole large enough to accommodate the 1-3/8-in-diameter mechanical anchor to pass though it during assembly by the roof bolt operator. The mine wanted to continue to use an extruded hole bearing plate in the tensionable system, and EMS was asked to propose a plate and angle-compensating device."

Jan 1, 2016

By M. Z. Naghadehi, E. Emami, J. Sattarvand, R. Battulwar

In this paper, a methodology for a computerised recognition of joint sets on 3D point cloud models of rock masses is presented. The process starts with classifying joints on a 3D rock mass surface through training a deep network architecture and validated using manually labeled datasets. Then, individual joint surfaces are identified using the Density-Based Scan with Noise (DBSCAN) clustering algorithm. Subsequently, the orientations of the identified joint surfaces are computed by fitting least-square planes using the Random Sample Consensus (RANSAC). Finally, the joint planes are classified into different joint sets, and the dip direction and dip angle for each set are calculated. The performance of the proposed methodology has been evaluated using a case study. The results show that the presented procedure is fast, accurate, and robust.

Sep 1, 2021

By Lawrence K. Nordell

The selection of belt conveyor drive systems (*) is the subject of ongoing investigation. Frequently this choice has been governed by an incomplete perspective on the major considerations. A more comprehensive and objective approach is desirable. This paper presents additional factors which hopefully will broaden this perspective. BACKGROUND Conventional belt conveyors are powered by electric or electro-mechanical drives(*) mounted at the conveyor's head, tail, intermediate return span, or a combination of these (Fig. 1). A list of the drives reviewed is given in Table I. The following are main elements influencing the selection of the drive system: 1) dynamic characteristics, 2) economic factors such as capital cost, plant spares compatibility, reliability, availability, maintainability, and 3) environmental constraints. The principal dynamic characteristics of concern are the reactions of belt forces generated by the drive system during starting of the conveyor. Another attribute for consideration is the application of multiple driven pulleys used to 1) lower the conveyor's belt tension requirements, 2) increase the expected tonnage throughput, allowing for possible drive component failures, and 3) increase the plant spares flexibility related to the drive assembly.

Jan 1, 1977

By L. G. Trudell, J. W. Smith, K. E. Stanfield

Representation of actual oil yields from sections of the Green River formation oil shales by two types of drill - cutting samples was evaluated . Average oil yields of single sets of mud cuttings from hydraulic rotary drilling in Colorado and gas cuttings from pneumatic rotary drilling in Utah were compared statistically with yields of core samples taken from adjacent holes . Oil yields from gas cuttings were identical to oil yields of core samples . Mud cuttings appeared to represent a section of the formation conservatively , the deficiencies increasing with increasing richness of sample . Because a large amount of the oil - yield data currently available for the Green River formation is based on mud- cutting samples , development of a valid correction method by additional testing is needed .

Jan 1, 1963

By Reza M. Rahman

The froth phase plays an important role in the flotation and upgrading of the final concentrate. At present, the techniques that have been used in the mineral industry to measure the froth recovery have limitations. The aim of this paper is to investigate the performance of the froth in an industrial flotation cell. A unique device has been developed which is capable of decoupling the froth zone from the pulp zone. It consists of two concentric tubes. The inner tube acts as a dropback collection chamber or catcher. The particles that detach from the froth phase fall directly into the catcher and are collected as froth dropback. The froth recovery measurements were carried out in a rougher bank of a copper concentrator treating sulphide minerals. The dropback device is designed so that it can be immersed into a plant size flotation cell and plant froth recovery measurements can be taken at any given time. During the experiments, the bubbles laden with valuable mineral particles entered the device from the plant flotation cell, subsequently rising to form a froth layer at the top of the device. The particles that detached from the froth zone were collected in the dropback collection chamber whereas the concentrate sample was collected by a launder. By drying, sizing and chemical analysis of the concentrate and dropback samples, the froth recovery, was estimated on the basis of the valuable component. The effect of air rate on froth recovery was also investigated. Keywords: flotation, froth, dropback, froth recovery

Sep 1, 2012

By Camila Barbosa Albani

Foram estudados os tipos de projeções, suas características e medidas de controle, a partir do acompanhamento de corridas na ArcelorMittal Tubarão, inclusive com amostragem e análises dos resíduos de projeção. Utilizando-se termodinâmica computacional estimou-se a viscosidade da projeção, que se mostrou muito heterogênea. Projeções ocorreram em uma faixa extensa de Si do gusa, inclusive em valores abaixo de 0,30%, com maior frequência entre 0,30% e 0,40%. As adições de minério de ferro tiveram forte influência na ocorrência de projeções possivelmente devido ao efeito conjugado de redução da permeabilidade e geração de gás. Um modelo conceitual das causas principais das projeções foi proposto e validado com observações de ocorrência de projeções tardias no sopro. Foi também proposto que as ações de controle de projeções deveriam ser ajustadas de forma a priorizar o controle da taxa de descarburação e o aumento da permeabilidade da emulsão.

Oct 30, 2017

By John C. Harkey

The paper shares programs that presently use the CDC PLATO System to train individuals in industry. A short history of PLATO development; as a training system is presented with reflection on the major training trends being used to improve training effectiveness. A discussion is offered to describe the benefits of using a system for individualizing instruction. An introduction; is offered showing how one can recognize' individual differences, with an explanation of how the strengths of a computer are used to deliver and manage the training. Simulations of hazardous processes are shown to be one of the most effective uses of the computer for training.

Jan 1, 1979

The 26th international APCOM symposium, hosted by The Pennsylvania State University, was held Sept. 16 to 20, 1996 in University Park, PA. Conducted about every 18 months throughout the world, APCOM symposia focus on the Application of Computers and Operations Research in the Mineral Industry. The APCOM International Council is the governing body of the symposia and determines the symposium’s locations and sponsorships. This group is composed of the nine permanent (voting) members. They include the University of Arizona, Colorado School of Mines, Pennsylvania State University, Society for Mining, Metallurgy and Exploration, Inc., Canadian Institute of Mining, Metallurgy and Petroleum, South African Institute of Mining and Metallurgy, Technical University of Berlin, Institution of Mining and Metallurgy and Australasian Institute of Mining and Metallurgy. The three nonvoting members are Moscow Mining Institute, China Institute of Mining and Rudarski Mining Institute of Slovenia.

Jan 1, 1996

Fundamental results obtained from research on the properties of the edge surfaces of kaolinite particles (~500 nm) are reported. Of particular significance was the development of the experimental protocol. Well-ordered kaolinite edge surfaces were prepared as an epoxy resin sandwich structure having layered kaolinite particles in the center of the epoxy resin sandwich. Images of the sectioned kaolinite edge surfaces were examined by atomic force microscopy (AFM), and the average thickness of kaolinite particles in this study was determined to be 38.3 nm ± 11.7 nm. Furthermore, the surface charge of the kaolinite edge surfaces was evaluated with a super sharp Si tip. The point of zero charge (PZC) of the kaolinite edge surface was determined to be below pH 4, in contrast to the traditional view that the edge surfaces of kaolinite particles may carry a positive charge at pH 4. This lower PZC of the kaolinite edge surface was attributed to the lack of isomorphous substitution in the silica tetrahedral layer when compared to the PZC for the muscovite edge surface. Our results are consistent with the particle aggregation and flotation behavior of kaolinite, and should provide the basis for improved flotation strategies leading to the efficient recovery and utilization of mineral and energy resources.

Feb 23, 2014

The Waimumu area, 12 km southwest of Gore, is underlain by the Gore Lignite Measures, an early Tertiary fluvial sequence approximately 500 m thick resting on Triassic-Jurassic argillitic basement. The Waimumu Quartz Gravels (Pliocene) have been deposited locally and are in part due to the localised reworking of the Gore Lignite Measures. Structurally the area is dominated by the Dunsdale Fault System, a steeply dipping series of NE trending reverse faults (Isaac and Lindqvist, 1990). The Belle-Brook, Hedgehope and Parker Road sites sampled are adjacent to the downthrown (east) side of the Hedgehope Fault.The authigenic gold-sulphide association at Belle-Brook was discovered in 1987 (Falconer, 1987: Clough and Craw, 1989). Despite a very limited amount of alluvial mining a significant quantity of authigenic marcasite has developed. Authigenic sulphide trace element analysis has shown anomalous amounts of As, Ni, Cr and to a lesser extent Zn, Pb and eu (Table 1). It has been established that the nickel occurs as a colloform banded Ni sulphide, possibly bravoite, within the marcasite (Figures 1 & 2). Arsenic and nickel (re)mobilisation are well documented in the literature. Generally As and heavy metals are mobilised in the groundwater as a result of the oxidation of sulphides (ie as a result of mining). At Belle-Brook it is reasonable to assume the authigenic sulphide trace element composition reflects either localised groundwater contamination or hydrothermal mineralisation. This poster presents some preliminary findings.

Jan 1, 2001

Waihi Gold Mining Company Limited, a wholly owned subsidiary of Normandy Mining Limited, operates the Martha gold mine, located in the township of Waihi, New Zealand. The operation, an unincorporated joint venture, comprises Normandy Mining Limited (67.070/0) and Otter Gold Mines (32.94%). Since gold was first discovered at Waihi in 1878, it has formed a key part of the region's economy. In 1909 the Waihi mine was described in a report to Parliament as æthe most important gold mine in Australasia and one of the greatest in the world.Æ That was a record year for production, with 416,813 tons of ore mined and some 1,120 men employed. Today the mine produces up to 1,250,000 tonnes of ore annually, and the project employs some 234 men and women. In 1999 the value of the gold and silver produced ($59 million) made up 47% of Waihi's estimated GDP. Waihi Gold has made significant contributions to the Waihi economy, community and the Hauraki region as a whole. Since the mine was re-opened in 1987, thousands of local people have benefited from the mine. In 1999, consents were granted allowing an extension to the mine life (the Extended Project) and this will result in a further seven years of economic benefits resulting from mining activity. The Company has undertaken extensive consultation throughout project planning, construction, operations and rehabilitation. Ongoing liaison and involvement with all community sectors, including Tangata Whenua and Iwi, local residents, recreational groups and schools remains an integral part of the operation. Throughout the life of the modern Martha Mine, the Company has actively supported the local community in the form of donations, sponsorships, the provision of amenities, and by participating in community events. A well established environmental team exists at the site. Environmental and community performance is measured by an independent five-assessment process, and the Company is committed to achieving excellence through ongoing improvement programmes and staff awareness. When the mine is closed, the open pit area will be transformed into a recreational lake, and the tailings storage facilities will be rehabilitated to become a combination of wetlands, grassed areas and ponds. Resources will be provided by the Mine to ensure the rehabilitated site remains in a safe and self-sustaining, stable condition in perpetuity. The mine is regarded as a showcase on a world standard of how a modem mining operation can successfully coexist with the nearby community.

Jan 1, 2000

By Gao Dazhao

This paper presents some research results of pile foundation performance. Measurements on the bearing behaviour and driving effects of piles have been carried out during pile testing and pile driving. It has been found that the ratio of end resistance to the ultimate load depends on the pile length, and the ratio in general is less than 40% for single piles. However for pile group, the end resistance seems to be greater than skin friction. The characteristic curves of skin friction and end re­sistance appear as interaction between soils and pile. The contribution of skin friction to the pile bearing capacity not only depends on soil properties but also on the relative position of the soil layer. The pore pressure and the lateral pressure in ground have been observed during the stage of driving piles. Based on the available data, the radius of plastic region and the coefficient of pore pressure A can be found analytically. The pore pressure time process curves which may be used for practice have been predicted by means of numerical method.

Jan 1, 1991

By Corry Goumans, Ron J. Elliot

This paper discusses the challenges encountered in drilling and blasting of a small diameter shaft underneath a parking garage in historic Gastown, Vancouver, BC. This project involved drilling in a restricted headroom area, blasting in a confined space environment, and excavating using a novel vacuum technique. The 1.2m x 1.2 m x 8.5m deep shaft was required for installation of a hydraulic piston for a show lift. The project called for very accurate drilling through inter-bedded sandstone and siltstone within the water table. Development of a unique blast design was required for blast vibration control on a historic structure located just 15.8 meters away. The shaft was successfully completed without damage to any of the surrounding structures.

Jan 1, 2004

By M. M. Gilkey

This report on water requirements for the New Mexico mineral industry includes data on industrial operations closely related to mineral production. It contains general information concerning public water supplies at five principal cities and a short discussion of water needs for agriculture. Background data are presented regarding the geography, hydrography, and water laws of New Mexico, as well as precipitation and evaporation characteristics of the State. Most of the information on source, quantity, distribution, cost, and treatment of water was obtained in interviews with company representatives. Water systems at 46 operations are illustrated by schematic waterflow diagrams. The study revealed that the New Mexico mineral industry in 1962 used about 16 billion gallons of new water and reused 152 billion gallons, a total usage of 168 billion gallons. Consumption amounted to 7.6 billion gallons. Of the 16 billion gallons of new water, 11.9 billion gallons was "self- supplied" from ground water sources, and 2.6 billion gallons was self supplied from surface sources. Approximately 1.5 billion gallons was purchased. Some of the water from company-owned wells is piped as far as 30 miles. Reported costs of the self-supplied new water range from 1 to 20 cents per 1,000 gallons and average 8 cents per 1,000 gallons for power and maintenance. Inadequacy of the supply of new water at many operations necessitates large-scale recirculation. Reported costs for recirculating water (power and maintenance) average 1.8 cents per 1,000 gallons. For the entire New Mexico mineral industry in 1962, the value of product was $42 per 1,000 gallons of new water intake and $88 per 1,000 gallons consumed. Analyses of 40 water samples, listed in the appendix, show the wide range in water quality at plants throughout the State. Projection of the 1962 water requirements of the mineral industry indicate that the total demand for new water will increase from the 16 billion gallons used in 1962 to 24 billion gallons in 1980, a 50 percent increase; and to 36 billion gallons in 2000, which is 125 percent more than the 1962 intake of new water.

Jan 1, 1965

By M. M. Gilkey

This report on water requirements for the New Mexico mineral industry includes data on industrial operations closely related to mineral production. It contains general information concerning public water supplies at five principal cities and a short discussion of water needs for agriculture. Background data are presented regarding the geography, hydrography, and water laws of New Mexico, as well as precipitatton and evaporation characteristics of the State. Most of the information on source, quantity, distribution, cost, and treatment of water was obtained in interviews with company representatives. Water systems at 46 operations are illustrated by schematic waterflow diagrams. The study revealed that the New Mexico mineral industry in 1962 used about 16 billion gallons of new water and reused 152 billion gallons, a total usage of 168 billion gallons. Consumption amounted to 7.6 billion gallons. Of the 16 billion gallons of new water, 11.9 billion gallons was "self- supplied" from ground water sources, and 2.6 billion gallons was self supplied from surface sources. Approximately 1.5 billion gallons was purchased. Some of the water from company-owned wells is piped as far as 30 miles. Reported costs of the self-supplied new water range from 1 to 20 cents per 1,000 gallons and average 8 cents per 1,000 gallons for power and maintenance. Inadequacy of the supply of new water at many operations necessitates large-scale recirculation. Reported costs for recirculating water (power and maintenance) average 1.8 cents per 1,000 gallons. For the entire New Mexico mineral industry in 1962, the value of product was $42 per 1,000 gallons of new water intake and $88 per 1,000 gallons consumed. Analyses of 40 water samples, listed in the appendix, show the wide range in water quality at plants throughout the State. Projection of the 1962 water requirements of the mineral industry indicate that the total demand for new water will increase from the 16 billion gallons used in 1962 to 24 billion gallons in 1980, a 50 percent increase; and to 36 billion gallons in 2000, which is 125 percent more than the 1962 intake of new water.

Jan 1, 1965

By Andrew R. Marchbank

The application of biologically assisted methods for metal extraction in the mining industry has a long history, but development of modern techniques has been relatively slow. There is, however, a resurgence of interest in the industry with the recent development of methods to successfully treat base metals concentrates. Two major pilot plant programs for treatment of chalcopyrite concentrates have been initiated in the past year and results from one are beginning to be released. This paper provides an overview of methods that have been applied in the past; from the earliest deliberate applications of the technology, through the copper and uranium heap and dump leach applications, the more highly engineered agitated tank leach gold applications and the developments currently taking place in the industry.

May 1, 2002

By G. K. Quainoo

In the automotive industry, the awareness to meet Corporate Average Fuel Efficiency (CAFE) standards has evolved the need to reduce vehicular weight in new automobile designs, with the overall goal of reducing gas emissions into the atmosphere (Kyoto protocol), One efficient method has been to use lighter materials such as aluminum in outer body panels, Heat treatable AA6111 is one of the materials employed due to its unique combination of formability, paint bake strengthening and superior corrosion resistance characteristics, Researchers have applied various thermo-mechanical processes on 6000 series aluminum alloys and have found an improvement in the mechanical properties of these alloys, For a formed and painted automobile panel, the final mechanical properties involve a combination of strength components arising from cold work, strain aging and precipitation minus recovery. In this study, the evolution of microstructure resulting from the interaction of cold work and precipitation in AA6111 has been studied by means of transmission electron microscopy (TEM) after subjecting samples to various heat treatments, tensile testing and differential scanning calorimetry (DSC), This has been done to understand the evolution of microstructure and its influence on the properties of the alloy, The results show a considerable improvement in strength with a corresponding increase in strengthening precipitates with increasing level of cold work in the alloy. DSC results following the application of various levels of cold work also show acceleration in the precipitate phase formation, as precipitates are observed to form at lower temperatures, with increasing level of cold work/

Jan 1, 2005

By JAMES J. PURDY

The great majority of stokers used in residential heating installations are of the clinkering type. Because of inherent characteristics of the under- feed combustion process as it occurs in these small stokers, and because of the wide range of operating conditions encountered in residential heating schedules, not all bituminous coals can be used successfully in residential underfeed units. The problem of providing consumer satisfaction has been attacked by the joint efforts of the stoker manufacturers and the coal industry; the stoker manufacturers have been concerned with improving their product to permit the use of a wider range of coals, and coal operators have made every effort to market selected and better prepared coals. In view of the wide range of physical characteristics and chemical properties of bituminous coals, the problems are real and are receiving increased attention.

Jan 1, 1949