Search Documents

By André L. B. Bittencourt

The copper content in the waste slag represents the greatest loss in the process of Caraíba Metais' Smelter. By identifying the variables responsible for copper stabilization in the slag, a minimization on these losses is expected, producing a granulated waste slag with a copper content lower than 0.7%. Statistics resourses such as control charts, Pareto's diagram and correlations curves were applied for the data obtained in the first semester of 1992. The magnetite and the calcium oxide contents in the slag of the Flash Smelter Furnace were most prominent variables. Some operational changes introduced during and after this investigation have shown good results.

Jan 1, 1994

By Wayne L. Johnson

The depth capability of engineering seismographs has been greatly increased by the use of signal enhancement, a technique in which seismic waveforms created by repeated impacts are digitized, stored, and summed. Summation amplifies the signal and partially cancels background noise. This gives a clearer picture of the wave aid makes it possible to determine the travel tune of signals from 'eater depth. Signal enhancement combined with continuous display of waveform, permanent recording of waveform, and precision digital readout of travel time has opened new fields of application in mining and engineering. Recent work has clown that replacement sulfides can be distinguished seismically from country rock at Bistee, Ariz. Work on the Iron Range of Minnesota indication,: that, by using a 300 pound weight as the source, the Biwabik iron Formation can be traced down dip to several hundreds of feet traverses over known areas show that reflections can sometimes be identified. Reflection, if identified preclsely, give a mere accurate estimate of depth and buried topography. Comparison of ( ) and weight drop have given some understanding of low wave amplitude varies win; source candid

Jan 1, 1971

By Mostafa Benzaazoua, Mariam El Adnani, My Ahmed Boumehdi, Rachid Hakkou, Salah Ouhamdouch, Abdelmalek Goumih

This study focuses on the environmental characterization and assessment of long-term neutral mine drainage (CND) potential from waste rock piles at the abandoned Erdouz mine in Morocco. The study involved metallographic analysis, static tests, and column tests. Results indicate that the waste rock is not an acid mine drainage generator but produces CND, mainly with sulfates exceeding Moroccan standards. The waste rock is relatively stable and could be reused after pretreatment.

Jan 25, 2022

By C. J. Coulson, G. A. McKay, A. M. Cormie

"The Leitch mine, in the Beardmore area, Thunder Bay district, Ontario, is a part of the Leitch estate. It includes a group of patented claims, staked by P. A. Leitch of Port Arthur early in the century, along bands of jasper, hematite, iron-bearing slates, carbonatized schists, and greywacke, commonly known as 'iron formation'. The folding and shearing in these variably interstratified beds is a striking structural feature. The vein pattern is very definitely related to these structures.ROCKSThe rocks in the area are typical Keewatin lavas-greenstone-overlain by a series of Timiskaming sediments consisting of arkosic greywacke, iron formation, slate, greywacke, conglomerate, and greywacke, in this order from the contact. The sedimentary beds are generally conformable with the older rock contact except on local folds.Small intrusions of diorite occur as nearly vertical dykes and are believed to be of Algoman age. To the northwest of the mine there are larger intrusions of granodiorite belonging to the same period.Several dykes of quartz diabase up to 100 feet in width, striking generally north and south, with a vertical dip, cross the property. These have been classified by W. C. Laird as pre-Keweenawan in age. One of these dykes in particular is of importance for it cuts through the No. 2 vein and serves as a pillar when stoping. It is approximately 6 feet wide.The youngest rock type represented is a sheet of olivine diabase that extends over an area of thousands of square miles in and around lake Nipigon. It underlies most of this area and its outcrops form some of the most interesting topographical features, with fault scarps rising hundreds of feet. In the vicinity of the mine shaft the sheet is about 600 feet thick and extends from a depth of 1,871 feet to approximately 2,470 feet. It has a dense, hard, chilled margin and a sharp, tight contact. It intruded the sediments with very little lateral disturbance. The chief effect was baking, which darkened and hardened the greywacke near the contact. The sheet dips flatly to the cast."

Jan 1, 1954

By Tim O’Neil

What prompted the merger of the two long-established American Mining Congress/National Coal Association (AMC/NCA) groups that combine the coal, hard-rock, industrial- and agricultural-minerals sectors of mining? Both associations have been facing similar stresses for several years - structural changes in their respective industries, the changing personality and role of government and well-financed and organized opposition groups. In 1993, the AMC board of directors undertook efforts at reorganizing the association. One board member, who serves on both boards, suggested it might be time to give serious consideration to merging the organizations. This is an idea that had been discussed more or less informally at least three times during my tenure at NCA. Negotiations toward a merger began after that and were consummated in February of this year.

Jan 1, 1995

By F. B. WEEKS

I HAVE chosen for my subject a mining district which in an article published four years ago I referred to in the following words: "One of the un- usual anomalies of mining development and history is that a district having added thirty or more millions of wealth to a principal mining state, situated within four to six miles of two transcontinental railways and two auto highways, and within 150 miles of the most widely advertised part of the United States, should have been so completely lost sight of that probably not one mining man in ten can tell offhand where it is situated." But this district never was a dead one: it was only slumbering. During the past four months, day by day, it has been emerging from that state of slumber.

Jan 1, 1929

By Nathaniel Arbiter

A fully-instrumented driving mechanism has been constructed to study the power, aerating and solid suspension characteristics of several laboratory flotation machines. Machines operating over normal flotation speed ranges give constant power numbers in liquid' systems indicating that they operate under fully baffled turbulent flow conditions. Owing to lack of geometrical scaling, power numbers for different sizes of cells of the same make are different. Even larger differences occur between cells of different manufactures. For a given impeller, varying the tank size did not significantly affect the power consumption. Tank geometry and baffling has a slight effect on power consumption with shrouded impellers. For a given impeller speed, suspension height decreases while power increases with increasing mass of solids in suspension. While power consumption is hardly affected by particle size and clearance between the impeller and tank bottom, the suspension height significantly increases as clearance increases and as particle size decreases. Aeration was found to affect not only power but also the suspension characteristics of the machine. For closely sized particles drastic sedimentation occurred when a critical value of the air flow number was exceeded. The critical air flow number decreased with increasing particle size. This effect was less marked with a wide particle size range. The self-aerating capacity of flotation machines increases with cell size at a given speed for the same impeller-shroud system, but decreases in the presence of frother and solids. Equations have been established for correlating all of the studied variables. Data taken from the literature were also correlated with these equations.

Jan 1, 1968

By E. Galán

The largest Spanish kaolin deposits formed on granites occur in Galicia (NW Spain) due to a widespread kaolinization of Variscan granitoids. This paper provides insight of the origin of this kaolinization process on the basis of a mineralogical and geochemical study carried out in two kaolin deposits, presently mined to be used in the paper industry. Mineral composition of the deeply kaolinized rocks is dominated by well-ordered kaolinite with minor quartz, K-feldspar, mica (illite/muscovite), locally gibbsite, and traces of resistant accessory phases (rutile, ilmenite, zircon and monazite). The content and structural order of the kaolinite decrease with depth. Kaolinite formed by extensive replacement of feldspars (plagioclase). Differential mobilization of major and trace elements during kaolinization has been inferred by using a mass-balance approach. Significant amounts of Na, Ca and minor Mn, Sr, P and U were removed from incipiently leachable minerals (plagioclase and apatite), and K, Rb, Cs and Ba were released from K-feldspar and mica. On the contrary, Ti, Zr, Th, Hf and the REE are retained in the resistant trace minerals that are concentrated in the fine fractions of the kaolins.

Jan 1, 2010

By Earl L. Fosse

"Preliminary examination of the Khayyam mine indicated that greater reserves of copper might be found by trenching, sampling, detailed geological and topographical mapping, and diamond drilling. The deposit seemed to be a potential source of sulfur, also, for use in the manufacture of paper pulp.Formal examination of the Khayyam mine by the Bureau of Mines was a follow-up of a preliminary examination made by W.S. Wright and the author on October 19-21, 1944. John Reed and W. S. Twanhofel, of the Geological Survey, visited the property during the summer of 1943 and suggested that the prospect be examined further.Preliminary examination of the Stumble-On claim was made July 1-3, 1945, concomitant with the formal examination of the Khayyam mine 11/2 miles to the west.In its program of exploration of mineral deposits, the Bureau of lanes has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy, It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts pre¬liminary examinations, performs the actual exploratory work, and prepares the final report, The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches arc under the supervision of Dr. R, S. Dean, assistant director.Special acknowledgment is due Robert S. Sanford, acting chief, Alaska Division, Mining Branch, for his help in the preparation of this report and during the project work.The Khayyam property is situated at 550 18’ north latitude and 1320 24’ west longitude on Prince of Wales Island in Southeastern Alaska. (see fig. 1.) The mine adit is 2,350 feet above sea level, near the summit of a mountain ridge, and 2.8 miles in an airline southwest of the head of McKenzie Inlet, a southern branch of Skown Arm. Skowl arm is navigable by ocean-going vessels .to the mouth of McKenzie Inlet, where reefs and rocky islands limit the channel width to 50 yards. Beyond this point the inlet widens to nearly half a mile. Coast and Geodetic Survey chart 8142 indicates from 12 fathoms of water at this narrow neck to more than 30 fathoms throughout the remainder of McKenzie Inlet, The old ore bunker and dock at the head. of the inlet are beyond repair. A new ore bunker and dock would have to be built if a large-scale mining operation were established.The mine can be reached by trail along the western ridge that lies on the west bank of Omar Creek. The trail is approximately 4 miles in length. The grade is rather steep to an elevation of 1,500 feet, but the last 21 miles can be traveled over gentle slopes along the crest of the ridge.Ketchikan is 30 miles by air and 42 miles by water from the head of McKenzie Inlet. Feed, hardware, fuel oil, lumber, and explosives can be purchased at Ketchikan and delivered by boat to McKenzie Inlet. By using an airplane, all small equipment and camp supplies could be using an airplane, all small equipment and camp supplies could be dropped with cargo parachutes near the mine."

Sep 1, 1946

By J. H. Welsh

This Bureau of Mines report presents guidelines to be considered in the design, installation, and operation of environmental mine monitoring systems in underground coal mines so as to enhance safety in the U.S. mining industry. A review of the current status of mine monitoring in the United States is also provided.

Jan 1, 1987

By E. H. Myrhaug, K. Aasly, T. Malvik

Quartz is one of the main raw materials for the carbothermic production of ferrosilicon and silicon metal. The ideal process is written: SiO2 + 2C = Si + 2CO The real process is much more complicated, depending on the quality of the raw materials. Several research projects have been carried out on quartz for the (Fe)Si process during the last 50-60 years. One of the important properties that have been discussed in this review is the volume expansion that takes place between 850 °C to 1000 ºC and explosive disintegration for some quartz types. No final and definite conclusions have been made but several reasons have been mentioned: The influence of the phase transformation to tridymite, which takes place within the same temperature interval, has been discussed in several papers. Alkali impurities have been mentioned as a critical factor for this transformation to take place. Other researchers have mentioned mica impurities as a critical factor for the behavior of the quartz at these temperatures. Studies of fluid inclusions in quartz was reported in some papers focusing on the volume expansion of these during heating as a source of explosive disintegration, especially along planes of healed micro fractures that often contain vast numbers of such inclusions. Several methods for investigations of the important properties of quartz have been presented and these provide a good basis for the further research on quartz raw materials.

Jan 1, 2007

By I. Serepa, N. C. Steenkamp

Investigations were conducted to determine the condition and stability of the existing decline at amine in the Kalahari Manganese Field, Northern Cape Province, South Africa. During the inspection of the decline, voids were identified behind the concrete lining on the hangingwall and sidewalls over a total linear distance of 230 m. The voids did not provide confinement and, as a result, self-mining was occurring behind the lining. Water was flowing into the decline, over a total linear distance of 100 m, at areas where the decline intersected incompetent rock units, causing softening of the concrete lining and deterioration of the surrounding rock mass. Further damage to the concrete lining was caused by expansion and contraction of the wet red clay unit. Remedial work comprised void filling and water sealing to prevent further deterioration of the decline and ensure that it remained operable for the remainder of the life of mine. Void filling was accomplished by drilling rows of holes along the decline to access the voids and filling the voids with foam. This was followed by the sealing with polymer fluids. Telescopic pipes were also installed to allow water to drain off. A visual inspection was conducted and check-holes were drilled to assess the quality of the remedial work. The void filling material had penetrated cracks in the concrete lining, and areas where voids were intersected by check-holes were re-filled. Additional holes were drilled to re-seal areas that were still wet. The remedial work was completed successfully, as all voids were filled and stability achieved without compromising the concrete lining. The ingress of groundwater was also reduced to some residual dampness.

Mar 2, 2022

By J Schrank

Double-stack trains in the United States date back to the early 1980s, starting about the time deregulation of the rail industry occurred. Freight rail became increasingly more competitive to trucking and barge or ship, and led to major investments in railroad infrastructure. Since most railroad tunnels in the United States were constructed between 1880 and 1930, they were not built tall enough to accommodate modern double-stack intermodal railcars. Therefore, as double-stack trains became the norm, existing tunnels became bottlenecks, and railroads wanted the tunnels made larger without impacting traffic. This need to increase the clearance while not impacting rail traffic launched a very specialised industry: the design and construction of replacement lining systems in existing tunnels.Several large multitunnel railroad clearance improvement projects have been completed in the country in the last decade, and they have all been done under ‘live track’ conditions. Live track conditions consist of work windows, often anywhere from four to 12 hours, that are provided to the contractor to complete the construction work. By the end of each work window, the tunnel must be secured so that the railroad can run trains.In addition to improving the clearance, these projects provided the railroads with an opportunity to improve the general condition of the tunnels, including structural, seepage, drainage and icing conditions. This paper discusses the design considerations, tunnel assessments and construction methods used for these live track railroad tunnel projects. Seepage and drainage improvements that were incorporated into the clearance improvement projects are also discussed.CITATION:Schrank, J, 2014. Live track railroad tunnel repair and clearance improvement in the United States, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 619–628 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A. CHESTER BEATTY

SO much has been written about African, and particularly about Northern Rhodesian, copper during the past two years that I feel safe in assuming that you are familiar with the general background of the Rhodesian picture. Therefore, I will confine myself to certain of the high lights in connection with the history, geology, development, ore reserves, and contemplated mining methods in this relatively new and highly important copper field., Unlike most of the other great orebodies of the world, the Roan Antelope mine was not discovered by the hoof of a starving prospector's faithful burro; nor even, as its name might suggest, by a well-placed kick of protest from an antelope stumbling over a malachite outcrop. Late in 1905 an English prospector named Collier, traveling in the N'Dola district, came upon some natives using a green powder for medicinal purposes. Closer examination of the powder revealed that it ' was ground-up malachite. Collier endeavored to persuade the natives to tell him where they obtained this medicine, but' for a long time without success, because of the general feeling among the natives that they did not wish to reveal the resources of their land to the white. Finally however, - he persuaded- brie 'of-the elders to at" least take 'him part way toward, the- place where the malachite was supposed to occur. The bid took him, to a point on the lower regions of the Luanshya river and there left him with the instructions that if he followed the stream up toward its.

Jan 1, 1931

By J. A. Organiscak

This paper describes the research con-ducted on bit wear and respirable dust generation conducted by the US Bureau of Mines (USBM) and West Virginia University (WVU), a member of the Generic Technology Center on Respirable Dust. The USBM investigated wear, energy and dust characteristics of various conical bit designs when cutting rock. WVU studied the functional relationships between wear, cutting force, energy, and dust of one conical bit type when cutting coal. The objective of the USBM study was to identify qualitative bit selection guidelines for cut-ting rock; WVU's research objective was to determine optimum bit replacement guidelines. These research studies both found that bit geometry (a function of bit design and wear) influences energy consumption and dust generation. Bit selection and replacement recommendations are given.

Jan 1, 1995

By Matthew Scott

Introduction The refining of precipitate is the final stage of all the processes involved in gold mining and cyanide milling, by which the precious metal is at last obtained in a concentrated form, which can be accurately valued and marketed. Possibly one ought to say, conveniently shipped, for accuracy in valuation depends in many instances on a toughening treatment given the bars as received at the Mint so as to obtain a homogeneous metal that lends itself to representative sampling; which, of course, entails a surcharge on the regular Mint charges for the extra work necessarily undertaken. There are several methods of refining zinc-gold precipitate, each with its advocates; the method employed depending not always on the quality of the bullion produced but on the local exigencies of the case in point. These methods are more or less detailed in various textbooks and it is not the purpose of this paper to discuss them, but to confine ourselves to the specific case as stated in the title of the paper. At the outset, it behooves the writer to express his thanks to Mr. Brigham, the General Manager of the Hollinger Mines, for the kindly consideration and encouragement given in developing this process. This will be better understood when one considers the immense values involved, tending towards conservatism in practice, and making one chary of radical innovations. This process has been in satisfactory operation now for about two and-a half years, during which time over twenty-five million dollars value in fine gold has been produced, so that it may be reasonably held that the process is successful.

Jan 1, 1931

By K. A. Grace

K.A. Grace's article advocates usage of the terms describing resources as defined by the US Bureau of Mines (USBM) and the US Geological Survey (USGS). Originally recommended in 1943, the terms were revised in 1976 and again in 1980. Mr. Grace further recommends that the term reserves should be severely restricted and that it should encompass mining and processing factors. The list of references quoted in the article does not, however, mention the study concerning reserves that was made over a period of almost four years by a joint Committee on Definitions. This committee was sponsored by three societies - the American Institute of Mining, Metallurgical, and Petroleum Engineers (AIME), the Society of Economic Geologists (SEG), and the American Institute of Professional Geologists (AIPG). Most of the detailed work was done by a working party appointed by the Society of Mining Engineers (SME) of AIME. After studying previous definitions in the US as well as in the United Kingdom, Canada, Australia, France, and other European countries, the following definitions were proposed and accepted in 1974 by the SME board of directors. (Ore reserve definitions in Rhodesia, South Africa, or New Zealand were not mentioned as having been reviewed.) Table 1 lists definitions from MINING ENGINEERING, July 1975. Notice in Table 1 it was mentioned, under Resources, that the definitions of reserves were recommended for the purposes of commercial evaluation. It was further stated that the terminology adopted by the USBM and the USGS, as released to the public, covering resources, was recognized as such. Mr. Grace also recommends that reserve calculations should allow for future losses in ore tonnage, ore grade, milling, and smelting. Unfortunately, it might take years to develop a prospect after it has been discovered. Mining methods have to be tested before being finalized in order to know what tonnage of ore is going to be lost, or how much dilution is likely to occur. The same problems are present in concentrating or in smelting. Operating mines usually know how mined grade compares with ore reserve grade. They can usually predict fairly closely what their final metal recoveries are probably going to be. It is, however, expecting too much to have to delay quoting reserves from say a recently drilled prospect. Any responsible mining geologist or mining engineer (or company for that matter) should state several things about an ore reserve calculation: that it is or is not a preliminary estimate only; that estimated grades have not been diluted to allow for a future, as yet unknown, mining method; that metal recoveries are or are not only tentative, based perhaps on drill hole samples only or on no metallurgical testing at all. Reserves of a partially explored prospect are always quoted when it becomes necessary to raise capital. If they are described as preliminary only (really just tonnage and grade estimates and not true "reserves") in addition to being accompanied by some of the items just mentioned, nobody is going to be misled. If, on the other hand, a report by a member of the SME or SEG is intentionally misleading, the individual must be reported and eventually disbarred from his or her society. To summarize, let us stay with the definitions of ore, ore reserves, and related terms as recommended and accepted by SME. I might add that on occasion I have used a fourth category in my ore reserve calculations, namely Geologically Possible Ore. This category is more or less the same as Inferred ore defined by the USBM and USGS. I have never given a grade to this category, which may be based only on geological mapping, geochemical sampling, or geophysical traversing.

Jan 8, 1985

By Jack G. Croeni

A study was made by the Bureau of Mines to determine the influence of high energy-rate deformation on the structures and properties of low-carbon steel, stainless steel, titanium, titanium-6 percent aluminum-4 percent vanadium, beryllium, molybdenum, and tungsten. The purpose of this study was to determine relative formability, the effect of energy and temperature on metalworking parameters and resulting structures, and the properties of materials formed by this technique. Forming techniques were limited to upset forging and direct extrusion on pneumatic-mechanical forming machines. Results show that considerable grain refinement can be achieved by careful control of deformation and forming temperature by high energy-rate techniques. Significant improvements in strength were observed as a result of this refined structure. Approximate deformation resistance as a function of temperature was determined for a variety of materials.

Jan 1, 1966

By James D. Brown

The Bureau of Mines has written a computer program in FORTRAN to facilitate the calculation of concentrations from X-ray intensities in electron probe microanalysis. Philibert's absorption and Castaing's secondary fluorescence corrections are used; no atomic number correction is included. Background and dead time corrections are applied to the data before calculating the relative intensities. Data from any type of electron probe microanalyzer can be used with the program.

Jan 1, 1965

By A. C. Fieldner

THE total annual energy production from coal, petroleum, natural gas and water power has been increasing at a fairly constant rate during the thirty years ending in 1930. But since 1913 the demand for the competitors of coal has increased at a rate faster than that for coal. During the last twenty years, the curve of coal production has had a generally horizontal trend; in fact, the 1930 production of coal was six per cent less than that of 1913. Economists attribute this loss of demand to greater efficiency in coal utilization and to displacement of coal by oil and natural gas. These two factors are about equally responsible, and it is evident that research has been intimately concerned with both. About sixty per cent of the bituminous coal mined in the United States in 1929 was used for generating steam, either in stationary or locomotive boilers. A decade ago seventy per cent or more was used for this purpose. This change is due largely to tremendous advances in fuel economy.

Jan 1, 1933