Search Documents

By Frank Yu, Bob Fukuhara

"The Stillwater mine is a 3,000 tons/day platinum/palladium underground mine and flotation concentrator located in the Beartooth mountain range in south-central Montana. The site elevation is 5,000 feet above sea level providing a climate with pleasant summers and cold winters. The winters are particularly characterized by very strong winds.The mining methods at Stillwater had been variations of overhand cut-and-fill and some blast-hole stoping. Until construction of the paste back-fill plant, mine back-filling was being practiced using classified hydraulic sand-fill methods. Where higher strengths were necessary, cement was added to the hydraulic fill, however, excessive quantities were necessary due to significant losses with the water drainage from the comparatively low-density fill. There was a need for higher strength back-fill with reduced cement content to augment the hydraulic-fill process.In early 1998, Stillwater Mining Co. commissioned AGRA Simons (then H.A. Simons) in a joint venture with The Industrial Company, TIC, to design and construct a treatment facility to re-process the mill flotation tailing, incorporating the following process alternatives:Produce 100 tph of low strength paste with unconfined compressive strength of 25 to 50 psi,Produce 100 tph of high strength paste with unconfined compressive strength of 100 to 125 psi,Direct all of the excess mill tailing to the sand-fill plant,While no paste is being produced, pump all of the mill tailing to the sand-fill plant,While no paste is being produced and the sand-fill silos are full, direct the mill tailing to the tailing pond.The paste backfill plant was therefore to be designed to produce the two different types of backfill paste as well as have the function of being the distribution center for the mill process tailing .Moderate to high slump pastes would be required because of the comparatively long horizontal transport distances, up to 8,000 feet, and the requirement for a low angle of repose to fill the stope evenly without numerous discharge points."

Jan 1, 2000

By G. E. McElroy

Ventilation-pressure surveys are required to determine the rates of pressure losses in various parts of mine-airway systems. These may be determined directly by differential pressure measurements or deduced from absolute pressure measurements, Despite the confusion caused by its inverted nonlinear scale, the altimeter has special application to pressure surveys in mines in which only small differences in elevation are involved, as is true for most of our large bituminous-coal mines in these, the judicious use of information obtained by pressure surveying can result in greatly improved working conditions as regards health and safety and, in many instances, can yield large financial returns. The main purposes of this report are to discuss methods of using altimeters for pressure surveys and to present the particular methods of making surveys and calculating the results of surveys used by the Mine Ventilation Section of the Bureau of Mines.

Jan 1, 1957

By W. M. Middleton

The exploiting of geothermal steam is a new endeavor in this country and is for that matter a very new science in the world. With the majority of steam wells in the world having been drilled during the last twelve years relatively little experience and knowledge has been gained that can guide us as compared to the techniques the oil and gas producers have developed for their use. We few technical personnel associated with the field find it a continuous challenge to understand and explain what effects or causes the various unusual phenomenon experienced. We have had unending discussions attempting to formulate pet theories which we can use as guides. We know, so the geologists tell us, that the source of the heat is from the hot magmatic core of the earth. Theory has it that the magma is cooling off and that hot gases are given off as this magma cools and shrinks. In volcanic' areas along fault lines where the magma reaches closer to the surface than in other areas, there is a higher concentration of gas evolution; consequently, geyser or geothermal areas are developed. As these hot gases rise toward the surface they encounter various minerals, including overlying bodies of water. It is into these underground lakes that our wells are penetrating. As the heat enters these lakes it spreads out by conduction, convection and water migration. We can strike this hot water over quite large areas in many of the geothermal fields. At present there is one anomaly to this in the United States as there is in Italy where our wells do not penetrate a hot water lake. This is at The Big Geysers in California. Here superheated steam is produced with a heat content, so high that it could not have been boiled off of a fresh water pool. This puzzled us until last year when a well was completed into a large body of brine in the Imperial Valley. This brine exists at close to 500°F and at a hydrostatic pressure sufficient to preclude any boiling. It is now believed by some of us that a similar pool of brine must exist below The Big Geysers area, from which the steam is emanating. If there is such a brine pool, it offers a plausible explanation of the high-heat content, for brine boils at a higher temperature than fresh water. I am now beginning to think that a similar brine pool may exist under all the geothermal basins for if it is under two of them, it is highly probable that it is under the others. The partial understanding of what we are drilling toward, and formulating a theory to explain its behavior helps guide us in our steam well drilling.

Jan 1, 1963

By Damian R. Siebert

Risk-reduction measures implemented during the design and construction of a 21-story pile-supported building adjacent to a below-grade 100-year-old sewer structure were keys to a successful foundation system. Avoiding damage to the existing sewer structure during construction activities and the future ability to access the structure post-construction were the main concerns for the utility owner. Clear communication and a deliberate design process between all parties ? utility owner, building owner, structural engineer, geotechnical engineer, architect, and contractor ? were integral to the project?s success. This collaborative process helped all parties to understand the risks, both real and perceived, and to develop mitigation measures to reduce the risks. Bringing together all parties to engage in dialogue and encouraging open communication throughout the project were paramount to its success. By implementing the joint design plan, using mutually-acceptable construction techniques, and careful monitoring, the building foundation was successfully installed and all parties? risks were averted.

Jan 1, 2011

By R. W. Stahl

Methane, a highly explosive gas evolved during the coal-formation process, is one of the hazards of mining most difficult to overcome. It is retained between particles of coal and entrapped in strata overlying and underlying the coal beds to a degree dependent upon the permeability of the enclosing strata. Considering that methane might be encountered at any time during the mining of coal, attempts have been made through the years to minimize the sources of ignition at coal-mine faces, such as the introduction of permissible electric equipment, the prohibition of smoking and open lights, and the development of safer explosives. The sparks created when mining-machine picks contact sandstone or iron pyrites2/ constitute one source of ignition, always recognized as a possibility but never greatly emphasized in the United States until recently, when ignitions began occurring with rather alarming frequency and in widely scattered coal-producing areas.

Jan 1, 1956

By R. Dawson Hall

LONG regarded as nearly worked out, the anthracite region still shows promise of a hundred years of life, for means are being found to get bottom, top, pillar, and other coal that earlier generations disregarded as too expensive to mine. Rock drivages and, still more, machinery are making it possible to get such coal. Mechanical methods enable the owner of thin beds to mine these with profit, and the miner recognizes that he must permit the use of machinery or the inexorable laws of economics will deny him opportunity to work. E. L. Dana, Jr., well outlines this situation, which in the past year became definitely established. Stripping also is recovering, safely and inexpensively, coal that past generations regarded as too hazardous and costly for mining.

Jan 1, 1935

By A. Sobering, G. N. Carlson

"This paper describes the conversion of the grinding section of the W a bush Mines pelletizing plant from conventional wet, open-circuit trunnion overflow ball milling, with filtering, and bentonite mixing on a common conveyor belt, to dry, open-circuit, grate discharge grinding, with pug mill mixing of bentonite and water at individual mills.The test work and data on operating economies to justify the cost of conversion are given. It is too early, at the time of writing, to have complete operating confirmation, but data are available. A brief description of the original plant is included."

Jan 1, 1971

By W. L. Zeigler

During the middle 1880's, shortly after the discovery of silver-lead ores in the Coeur d'Alene district of northern Idaho, it became apparent that concentration of the ores would be necessary to obtain a profitable product. Too much siliceous material was present for direct smelting, and the majority of the ores found at depth were too low in metallic content for economic smelting processes at the time. As the ores occurred in quartzite shear zones with siderite and quartz gangue, a large quantity of waste material was present in all the mines. As the galena was not finely disseminated, this made possible relatively good extraction of the argentiferous galena by coarse concentration. The first concentrators consisted mainly of coarse crushing, screening and jigging, principally by Harz jigs, the slimes being treated on buddles. Later Wilfley tables took the place of sand jigs and vanners superseded the buddles. Because of the marketing conditions, no attempt was made until 1900 to effect a recovery on the zinc minerals present, which were found associated in varying amounts with the galena. All through this period, the greater part of the production was obtained from mines containing ore assaying high in lead and low in zinc. Parts of some ore bodies would be reversed in this respect, so that ores high in zinc were left intact. During the decade after 1910, several important mines, The Success and The Interstate Callahan, containing ores high in zinc, were put into operation and were a material aid in the needed zinc production during World War I. Gravity concentration by jigs and tables was used during this period, with bulk flotation increasing in popularity for the treatment of the fine material that had already been treated by ordinary slime concentrating machinery. No extra fine grinding for flotation concentration was thought profitable at the time. Tailings Discharged into Streams From the start of mining and milling operations in this district until 1904, no attempt was made by the various mills in the upper district to impound or stack their tailings. They discharged them directly into the adjacent creeks or streams, to be carried away by high water. The Bunker Hill and Sullivan and the Last Chance mines, both in the relatively flat valley of the district, stacked huge piles of the coarse jig tailings on the near-by river bottom. Rain and snowfall are heavy in the Coeur d'Alene district, as it is on the heavily timbered Pacific slope of the Bitter Root Mountains. A heavy runoff occurs every spring and there is an occasional flood of disastrous proportions when warm "Chinook" winds accompanied by rain

Jan 1, 1949

By K Gordon, A Black

Two remediation strategies have been considered to reduce the levels of acidity and dissolved metals in acid mine drainage discharging from Sullivan Mine, West Coast, New Zealand. The oxidising strategy involves adding alkalinity and dissolved oxygen (DO) resulting in the precipitation of metallic oxides and decreased acidity. The reducing strategy involves removing DO, resulting in the precipitation of metallic sulfides, followed by addition of alkalinity to decrease acidity. Field remediation trials indicate a reducing system may be more effective for this site than an oxidising system. A residence time of only two hours in the limestone layer of a successive alkalinity producing system (SAPS) is sufficient to reduce acidity by 100 per cent, iron by 71 per cent, aluminium by 59 per cent, nickel by 38 per cent and manganese by 26 per cent. The proposed remediation plan will likely include a series of SAPS, followed by an anoxic limestone drain, and settling ponds to capture any remaining precipitates.

Jan 1, 2003

By Gisele R. Passalacqua, Taylor Malangone, Subhash Mahali

New York City is a busy metropolis with 8 million people. New York has the largest public transportation system with 6 million riders a day throughout the subway system. Keeping this infrastructure in service is vital to the overall economy of the region. Hurricane Sandy proved to have a devastating impact on infrastructure in Metropolitan New York. New York City Transit is on the forefront to provide resiliency and maintain its facilities with the use of flood protection systems. This paper presents flood protection structures utilized at Hammels Wye substation site in Far Rockaway, Queens, New York. The site is in close proximity and surrounded by water. The subsurface conditions consist of loose silts overlain by medium dense glacial sand. The high groundwater level combined with limited access to the site presented challenges. A flood protection system consisting of flood walls was recommended for this site. In certain areas the flood walls consisted of retaining walls supported on micropiles. For other areas, the flood walls consisted of steel sheet piles with jet grout columns to reduce seepage below the walls. The effect of driving sheet piles with vibratory hammers on nearby existing structures is always a concern. Recently, hydraulic hammers with variable moment/frequency are being considered as a mean to reduce vibration effects during driving. In this project, an instrumentation testing program was performed to measure peak particle velocity during sheet pile driving utilizing the variable moment vibratory hammer. Plots of peak particle velocity versus frequency were generated. This paper will present the design aspects of the flood walls and construction challenges during installation. This will prove beneficial to engineers in both design and construction fields.

Sep 8, 2021

By H Weitz

Bateman Engineering provided process technology and engineering design to China Yunnan Metallurgical Company (CYMCO) for a 30 MW DC furnace for the production of high-grade titanium dioxide slag.Following the successful commissioning of the furnace during the latter part of 2009 and the first quarter of 2010, a period of adverse circumstances resulted in having to operate the furnace without feed and at a low power input for a period of time. When normal feed resumed, a layer of solid material was detected on the slag-iron interface during sounding measurements. The condition of the iron was also significantly altered. The iron temperature was much higher than the design value, but the carbon content had decreased to such an extent that a large amount of iron solidified in the furnace, which made iron tapping very challenging. The slag temperature was increased in order to melt the solidified iron. However, severe sidewall damage resulted, which finally led to a burn-through. A number of samples were taken from the slag that remained in the furnace. These samples were analysed to determine the chemistry and phase profile throughout the slag bath. The mechanisms of formation of the high melting-temperature phase on the slag-iron interface are discussed, as well as procedures that can be applied to prevent a recurrence of this phenomenon. Some recommendations are made for instances when furnace feeding is interrupted for an indeterminate period.

Oct 5, 2011

By Xuexin Ding, Weijie Wei, Jinwang Zhang, Yi Chen, Shengli Yang

"Many ultra-thick coal seams exist in Xinjiang and the northern part of the Inner Mongolia. These coal seams are more than 30-40m thick. This kind of the thick coal seam is too difficult to extract in one slice, so the top-coal caving longwall mining method was designed for this purpose. In order to study the movement characteristics of the overburden strata and the development of the ""three zones"" in ultra-thick coal seams, the physical and numerical simulations were carried out based on the in-site condition of Baiyinhua coal mine. The result shows that, when extracting the upper part of the l 5m thick coal seams, the first weighting interval was 50-58m and the periodic weighting interval was I 8-20m. The caving zone, fractured zone and bending and sinking zone were 38m, 92m, and 50m respectively in height. The fractured zone height increased with the advancing distance of the face, but in some localities, a ladder-like distribution due to the periodic weighting existed. When extracting the lower part of the 25m thick coal seams, the roof was extremely broken and the collapse range of overlying strata continued to increase in irregular form.INTRODUCTIONThe thick coal seams occupy 44 percent of coal reserves in China and account for 45 percent of the gross domestic coal production. There are three main methods for extracting the thick coal seams: sublevel mining, large height mining, and longwall top-coal caving (LTCC) (Wang, 2009). Due to the rapid development of LTCC in the past two decades, it has become the most extensively used mining method. It possesses the advantages of high-production, high-efficiency, low development ratio, and low-cost (Yang, Zhang, Chen, and Zhengyang, 2016; Wang and Zhang, 2015). Baiyinhua coal mine's coal reserves are full of uniformly distributed thick coal seams, with the minable thickness of the main coal seam between 25 to 40m, i.e. the main coal seam is an ultra-thick coal seam. Sublevel longwall top-coal caving (SLTCC) which is an efficient method for extracting the ultrathick coal seams has led to multiple disturbances Xie, Chen, and Wang, 1999; Singh and Singh, 1999; Xie, Chang, and Yang, 2009. Therefore, using the case of Baiyinhua coal mine, the movement features of overburden strata and development characteristics of the three zones in ultra-thick coal seams were studied by physical and numerical simulations (Qian, et al, 2003; Qian, 1994)."

Jan 1, 2016

By Douglas Brand

"The data that many mineral processing plants make use of, is provided by samples taken from sampling systems which are inadequately designed or improperly maintained, and therefore cause detrimental effects to plant operations, production planning and metallurgical accounting! Poorly designed or maintained sampling systems will likely produce low probability samples which give the operator a false sense of security of the product and the process. If data is the basis for action (Flintoff, 1992, p.2), then using the resulting suspect or bad assays by operators, control systems, or metallurgist and administration personnel will act and make decisions which may adversely affect the profitability of a processing plant. Here we will discuss some of the fundamental sampling problems, propagation of errors and a method to estimate what impact this has on an operations Net Smelter Return.INTRODUCTIONIn order to control a mineral processing plant at its best potential, it is necessary to obtain the best possible measurement results of the metal or mineral in question. The sample which is delivered to a measuring instrument, or lab, needs to be of the highest probability to be able to achieve this. This paper will discuss the effects of sampling errors on grade / recovery and grade / Net Smelter Return (NSR) and provide a method to estimate the monetary advantages of using probabilistic sampling in a processing plant.REVIEW OF SAMPLINGSampling, by definition, is the removal of a small representative portion from a total consignment, or flow, for the purpose of accounting or process control.• A sample can only be considered representative, if each and every increment collected, in each of the sampling stages, is representative.• Each particle of the sampling lot must have the same probability of being included in the final sample.• If both of the above conditions are met, then the final sample will be representative of the complete sampling lot.It is commonly known that in order to take truly representative and probabilistic sample, best practices indicate that:• The total stream should be sampled.• The sample cutter should intersect the sample at right angles to the flow.• The sample cutter should travel through the stream at a linear and constant speed and the speed deviations should be less than 5%."

Jan 1, 2016

Enterprise Optimisation is a methodology for increasing the value of mining and mineral processing operations through better long-term planning decisions. It involves a combination of ten mechanisms which deal with decisions at different stages of the value chain. A decision made at any point in the chain potentially affects the decision for all other points in the chain. The key, therefore, is to optimise them simultaneously. The Enterprise Optimisation approach can be shown to produce increases of five per cent to 35 per cent or more in net present value (NPV), even when several optimisation methods have already been applied. This paper steps through an example case study, illustrating the effect of each mechanism and how they can work together to develop greatly improved results. This example results in a series of counter-intuitive outcomes, which challenges conventional management practices and typical organisational objectives based on organisational silos.

Dec 6, 2010

By B Murphy, N Strong, J Albrecht

Rio Tinto’s Argyle Diamond Mine has a history of underperformance with delivery of ore from the underground operation to the surface for processing with no real clarity in sources of loss and value. In order to increase underground production performance, the basic concepts of the Theory of Constraints model were applied to the Argyle underground production system. This prompted a revised view on bottlenecks and contributors to value loss and ultimately leading to record breaking mine performance. System loss reporting to demonstrate the best opportunity to drive value, departmental detail to develop tools to identify improvement opportunities and clarity across the team to ensure alignment and clear lines of communication were critical to the project success.

Mar 15, 2021

Au-Ag Recovery from Complex Ore by Flotation

Sep 13, 2010

By S M. Denn

The Cawse nickel-cobalt operation is situated 50 km NW of Kalgoorlie in Western Australia, at latitude30o22'30'' south and longitude 121o08'30'' east on the Kalgoorlie 1:250 000 geological map sheet (SH 51-9) (see Figure 1). The project is owned and operated by Centaur Nickel Pty Ltd (CTR) and was the first in Australia to commercially produce nickel metal and cobalt sulphide through pressure acid leach (PAL) technology. Cawse has a total resource base (all categories of resources + reserves) of 213 million tonnes Mt at 0.7 per cent Ni and 0.04 per cent Co, comprising 127 Mt at Cawse Central which is 100 per cent owned by CTR and 86 Mt at Cawse Extended where CTR has a 80 per cent equity. Cawse Extended is located immediately to the northwest of the Cawse Central leases. All current reserves (proved and probable) of 30 Mt at 1.0 per cent nickel are contained within Cawse Central. In addition the Siberia project area 20 kilometres to the NW has a resource of 63 Mt at 0.7 per cent Ni. Cawse is a dry laterite deposit, with nickel and cobalt hosted by iron and manganese oxides. Cawse Central mineralisation extends over a ten kilometre strike length, with three pits currently being mined. The Bunyip pit has the premier nickel and cobalt grades within Cawse Central. There are seven dominant lithology types forming mappable units within current pit exposures. Four of these units are host to nickel and cobalt mineralisation. Ore types are defined as Upgrade, Grind and Non-upgrade, depending on their physical characteristics with respect to the treatment route. Mining commenced in February 1998. To the end of calender 1999 the operation has produced 2100 tonnes nickel plate and 470 tonnes of cobalt as a cobalt sulphide product. Future production will target 9000 tonnes per annum Ni metal and up to 2000 tonnes per annum Co, based on processing 500 000 tonnes of ore per annum.

Jan 1, 2000

By James J. Kabat, James A. McDonald

Impregilo/SA Healy JV recently completed this Project using the first slurry shield TBM’s in the United States. The Project used two TBM’s to mine 18,000 feet in sands, gravels, and silty alluvial materials under the Willamette River and downtown Portland, Oregon. This paper discusses alignment and geological conditions, equipment selection and plant setup, and tunnel excavation means and methods, parameters, and results. Extensive hyperbaric operations were required and will also be discussed.

Jan 1, 2007

By Dewey W. Geary, Rachael V. Bisnett, R. Michael Bivens, Thomas G. Andrews

"The powerhouse for the Red Rock Hydroelectric Project is being constructed at the toe of the existing U.S. Army Corps of Engineers’ Red Rock Dam immediately adjacent to the existing stilling basin retaining wall. The powerhouse excavation extends though overburden and 40 feet into rock. Prior to rock excavation, a grouting was performed around the excavation for the purpose of increasing the strength of zones of fractured rock. For the majority of the perimeter, the rock was fairly tight and grout takes were relatively low. However, for a 160 foot extent along the landside of the excavation, extensive grouting was required to treat a two to five foot thick zone characterized by artesian flows from grout holes on the order of 20 gallons per minute (gpm) or higher from a voided zone in rock that was partially filled with sand, clay, and rock fragments. This paper discusses the treatment measures used to fill and improve the strength of this zone, which ultimately entailed a combination of thick cement grout and polyurethane grout, holes spaced as close as 18 inches on-center, and two additional rows of grout holes.IntroductionThe Red Rock Hydroelectric Project (Project) is currently under construction at the existing U.S. Army Corps of Engineers’ (USACE) Red Rock Dam on the Des Moines River near Pella, Iowa. At peak generation, the Project will generate up to 55 MW with an average annual energy output of 178 gigawatt-hours.The powerhouse for the Project will be located at the toe of the existing dam immediately adjacent to the existing stilling basin retaining wall. The powerhouse excavation extends up to a depth of 40 feet into rock through the St. Louis Limestone and terminates in the Warsaw Limestone. Prior to rock excavation, grouting was performed around the excavation for the purpose of improving the strength of zones of fractured rock. An auxiliary benefit of the grouting was reducing seepage into the excavation. Grouting began on July 20, 2015 and ultimately concluded on September 26, 2015.Drilling and grouting occurred as planned on the riverside (southwest) of the excavation along the cellular cofferdam and stilling basin wall (grout holes P-1 through S-13) and on the upstream (northwest) side of the excavation along the secant pile excavation support wall (grout holes P-14 through S-19) (refer to Fig. 1). The rock in these areas was generally tight with relatively low grout takes. However, on the landside (northeast) of the excavation (grout holes P-20 through P-28), partially infilled voids and artesian flows were encountered during drilling generally between depths of about 28 to 40 feet."

Jan 1, 2016

By E. Zucker

In this paper, as in the 1960 CIM paper of the same name, s1gmf1cant new developments in electrical-mechanical mining equipment are briefly described. These include static thyristor-supplied D.C. drives for mine hoists, load-haul-dump systems, process controls with small and medium-size computers, and several other new items of equipment and Concepts. All the new hardware descriptions are given in the context of over-all process integration. This means the actual mechanical linking together of two or more processes and the preliminary step in the development of production-line mining.

Jan 1, 1969