Search Documents

By D. W. Brunton

THE maps of our large mines are usually prepared with the greatest care; and it is somewhat singular that, in comparison with the great amount of time and money spent in surveying and platting, so little actual use is made of them. Almost the only purpose for which a completed survey-map is afterwards consulted, is the determination of the relative position of the different workings to each other, and to the boundary-lines of the property. After the completion of such a map, it should be made the beginning of another, and in most cases a far more important, undertaking, namely, its utilization as -a starting-point for a complete inventory of the company's underground possessions. The ordinary mine-survey map, being nothing but a record of what has been done, is, in one sense, only ancient history. To increase its value, such additions should be made as will render it a complete statement of the amount and value of ore in sight at any particular time, and a guide for future develop¬ments. Comparatively little extra labor is involved in this undertaking, since the larger and most expensive part of the work has already been completed when the mine has been surveyed and mapped. The necessary additions consist in working out, and platting on the maps, the geology of the mine as exposed in the workings, in such a manner that the geological survey may be of daily use in the development and operation of the mine. The first step towards the production of a geological map consists in tracing individual level-sheets from the general or composite map. The area to be included, outside of the property in question, will depend very much on local conditions; but, for geological, legal and commercial reasons, it should be extended as far as reasonably practicable. The scale to be

Sep 1, 1905

By E. Siami-Irdemoosa, S. R. Dindarloo

"Pareto analysis was used to investigate the failures database of a Hitachi EX1900 hydraulic shovel over one year of continuous operation. The hydraulic system and hydraulic links, hoses and piping were identified as the most critical system and subsystem, respectively. A three-parameter gamma distribution function was identified as the best fit for a probabilistic modeling of the time between failures (TBFs). This distribution was used in a Monte Carlo reliability analysis of the hydraulic system. Autoregressive integrated moving average (ARIMA), within the context of a time series analysis of the TBFs, was proposed as a viable alternative to the traditional technique of distribution fitting. The mean absolute percentage error (MAPE) metric was used to compare the two models. The MAPE value that resulted from the ARIMA was 66 percent smaller than that from the traditional technique in predicting the TBFs. Resumen ¦ Se usó análisis Pareto para investigar la base de datos de fallas de una pala hidráulica Hitachi EX1900 durante un periodo de un año de operación continua. Se identificó al sistema hidráulico y a los enlaces hidráulicos, mangueras y tuberías como el sistema y subsistema más importantes, respectivamente. Se identificó una función de distribución de tres parámetros gamma como el más apto para un modelado de probabilidades del tiempo transcurrido entre las fallas (Tabes por sus siglas en inglés). Esta distribución fue usada en un análisis de confiabilidad Monte Carlo para un sistema hidráulico. El promedio de movimiento integrado auto-regresivo (ARIMA por sus siglas en inglés), dentro del contexto de análisis de serie temporal de los TBFs, fue propuesto como una alternativa viable a la tradicional técnica de ajuste de distribución. Se usó el porcentaje de la media absoluta de error (MAPE) para comparar los dos modelos. El valor MAPE que resultó de la ARIMA fue 66 por ciento menor que el resultado obtenido con la técnica tradicional de predicción de TBFs."

Jan 1, 2015

By J. B. Gwiazda

S. Budirsky J.B. Gwiazda's article deals with an interesting problem that has not been studied thoroughly up to now. Gwiazda has proposed a technical solution that eliminates horizontal load imposed by the supports on the roof. That load is due to a discrepancy between the trajectories of the canopy and the overlying strata. It is true that the improved lemniscate guidance system proposed by Gwiazda could eliminate the horizontal load but, on the other hand, it would represent a higher cost of the supports, and it would complicate the already complicated mechanism of powered supports. That is why we must be convinced that the proposed improvement is actually needed. From that point of view, the following questions should be elucidated. As shown in Fig. 1, the point 0 travels along the curve a, which produces horizontal load on the roof in the direction of the coal face. As stated by Gwiazda, "such a high load is capable of destroying the roof above the support, causing rock debris to be scattered around the face." The results of our measurements carried out in coal mines of the Czechoslovak part of the Upper Silesian Coal Basin show that the convergence in the modern type of powered supports does not exceed several millimeters (not more than 10) per hour. Similar conclusions were drawn from field measurements performed in the Polish part of the Upper Silesian Coal Basin (see S. Romanowicz and H. Szopka in Proceedings, Scientific and Technical Symposium Simmex'85, Katowice, Poland, pp. 73-83). The small vertical closure of the supports also induces a small horizontal displacement of the canopy. In addition to this, the transmission of forces between the roof and the canopy is influenced by the layer of debris on it, i.e., the canopy slides without imposing a greater horizontal load on the roof. This was deduced from field measurements of Voest-Alpine F 4/4500 powered supports equipped with rams instead of the common front lemniscate links (denoted as 1 in Fig. 5). In these supports, the pressurizing of the space of piston rod (1a in Fig. 5) causes the rams to close, which induces horizontal load on the roof in a direction toward the coal face. After the setting of a support unit, the pressure in the piston rod space was found to drop, frequently to zero, because the small horizontal sliding between the canopy and the debris or inside the debris caused the horizontal reaction from the roof to fall to zero, although the debris were pressurized by vertical setting load. As a consequence, there was no horizontal load imposed by the canopy on the roof. A rise of the horizontal load was recorded only after the passage of the shearer and during lowering of the adjacent units. Thorough information on the results of the aforementioned field measurement is given in the paper, "Analysis of the performance of shield powered supports installed in a thick seam," published in Mechanizacja i automatyzacja gornictwa, 1982, No. 12, pp. 38-46. An English translation of the paper is available from the author. We have deduced from our observations that horizontal load imposed by the canopy on the roof in the direction toward the coal face is useful for roof control because it limits the displacement of the immediate roof toward the gob particularly during the rise working. We came to the conclusion that horizontal load on the roof toward the coal face should be induced on purpose. Could Mr. Gwiazda prove with the results of field measurements his contrary opinion? Has the small horizontal displacement of the canopy toward the face actually had an adverse effect on the roof? As shown in Fig. 2, during the setting of a support unit, the canopy imposes a horizontal load on the roof in the direction of the gob. In this case, I share Gwiazda's opinion that the horizontal load could have an adverse effect on the roof. Nevertheless, two important circumstances were neglected - the horizontal compliance of the supports and the interaction of adjacent units. The question of the compliance was analyzed precisely by I. Krumnacker in Gluckauf-Forschungshefte, 1984, No. 5, pp. 219-223. He found that due to the clearance between the hinge pins and the eyes of the sheild and due to the elasticity of the steel structure,

Jan 1, 1987

By Jorge Navarrete

La Corporación Nacional del Cobre de Chile produce cobre y otros subproductos a través de sus yacimientos y líneas de producción como las pirometalúrgica, hidrometalúrgica y biohidrometalúrgica. En este sentido, el presente texto señala la implantación de un LIMS para la industria minera de cobre. LIMS es una abreviatura genérica para los software de Administración de Información de Laboratorio, cuyo objetivo es relacionar la Informática, Quimiometría y Calidad.De forma que cumpla con los objetivos de adquisición y gestión de la información de pesaje, muestreo y análisis químico producida por diferentes áreas, tanto internos como externos y unidades funcionales.

Jul 17, 2000

By M Logsdon, B Johnson, M Fordham

The underground Neves Corvo copper-tin mine in southern Portugal currently disposes of its tailings in a ætraditionalÆ wet tailings impoundment. With the development of new technologies for preparation and transport of thickened tailings or paste, alternative tailings disposal options have become available that provide a more sustainable water management system and a higher degree of environmental protection. In addition, growing European resistance towards subaqueous disposal may well result in mandatory use of dry disposal methods in the near future. Twenty-four tailings disposal alternatives were evaluated through a cost-effective and easily-implementable bench-scale geochemical screening program conducted at site. Since the tailings are pyrite-rich and highly acid generating, particular emphasis was placed on monitoring likely indicators of sulfide oxidation under the various simulated disposal scenarios. Dependent parameters investigated as part of the program included moisture content, use of alkaline additives (lime, cement), use of a bactericide, and agitation. Response parameters included paste pH, specific conductance, and temperature as indicators of oxidation. The testing was carried out for 30 weeks. Results indicate that a number of relationships between the geochemical stability of the samples (ie sulfide oxidation) and sample characteristics can be readily identified. Based on the results of the screening program, a limited number of tailings mixtures have been selected for further long-term testing in field weathering cells to aid in the identification of the optimal mix design for future tailings disposal at the Neves Corvo Mine. This type of testing provides an inexpensive and reliable methodology for semi-quantitative comparison between tailings disposal alternatives, in particular at locations where more rigorous evaluation through long-term, fully replicated testing is not immediately feasible.

Jan 1, 2003

By E. Pribonic

Failure of a mine material hoist can cause injuries, fatalities and significant infrastructure damage, along with an associated loss of production. Principal causes of hoist accidents are overwind and underwind. Past and present means of arresting hoisting equipment are marginally effective and utilize destructive systems that are not reusable following an arrest. The use of permanent magnet eddy current arrestor technology is proposed; the history and fundamental science of the technology are presented, followed by real world examples and calculations of performance for failsafe, friction-free, instantly reusable eddy current arrestors as applied to stopping a 30-ton ore skip traveling at 16 metres per second. A comparison of existing arrestor types with the eddy current arrestor is included and limitations of the ECA are also discussed.

Jan 1, 2008

By B. J. Moore

This publication contains routine analyses and related source data for 419 natural gas samples from 22 States collected during calendar year 1964 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863/ and 576.4/ Six previous publications have been made to present the results of 6,293 gas analyses made by the Bureau of Mines, Helium Activity, prior to 1964. The first three, Bulletins 486,5/ 576,6/ and 617,7/ contain analyses and related source data on 5,214 gas samples collected from

Jan 1, 1966

By John S. Crout

TWENTY-FIVE years ago the training of an engineer was of interest solely to the educator and to the student entering the field. At that time the engineer's position in society was relatively simple. His training emphasized design and operation and he expected to enter industry to handle the engineering problems of raw materials production, mechanical and product design, and the operation of power plants, factories, transportation and communication systems, and similar phases of industrial activity. He was not concerned with or particularly interested in the problems of management, administration, sales, publicity, industrial relations, or of legislation. To a large degree he was content to leave these matters to self-made businessmen, or men trained in law, finance, or commerce. That period in the evolution of the engineer is now history. It is generally conceded that the modern world is dependent upon engineering technology for its day-to-day survival. The continued operation of facilities on which mankind relies is dependent upon the functioning of mines, utilities, chemical plants, and other factories, all of which require the knowledge and the skills of trained engineers. Thus from a purely mechanical point of view, the engineer has become indispensable to

Jan 1, 1947

By J. W. Paul

[A study of mining methods and underground practices as they influence injury from falls of roof or coal reveals data as to the location in the mine where such injuries occur with the greatest frequency and as to some of the methods and practices which are in use for the prevention of injury. This paper, which presents statistics bearing on the frequency and place of occurrence of accidents and, discusses regulations and practices which have resulted in a low frequency rate from falls of roof and coal in a few representative mines takes its information from mine-accident reports and from the results of studies conducted in a group of 80 mines in the bituminous coal fields of western Pennsylvania, Ohio, and West Virginia. The statistics from this group of mines cover periods of one to four years but average 2 years and 7 months. During this time these mines produced over 110,400,000 tons of coal, equivalent to one-fifth of the annual production of all bituminous mines in the United States. The coal beds of the mines in the group studied are mostly flat, with local pitches of moderate degree. A number of mining plans are in use, each of which follows a general system of multiple entries, cross entries, and rooms. Room and pillar in panels either advancing, retreating, or half advance and half retreat and the block systems are employed. The methods of pillar extraction are by splitting, slabbing, pocket-and-stump, and open end. It is hoped that in presenting some of the details of the methods and practices at particular mines of this group which have commendable records in the prevention of injury some good may accrue to many other bituminous mines which 'nave similar natural conditions.]

Jan 1, 1933

By D. D. Munro

Finsch Mine is a Kimberlite diamond mine located at Lime Acres in the Northern Cape of South Africa. The mine was founded in 1961 and started surface-mining in 1964. Underground production commenced in 1990 using a Modified Blast Hole Open Stoping method for the mining of Blocks 1,2 and 3. Block 4 is currently being mined as a Block Cave. The process of identifying and optimizing a mining method to mine the Block 5 ore body started in 1991 and in 2006 Inclined Caving was identified as being a technically feasible method. This report aims to document the process employed in developing this method by the Block 5 Pre-Feasibility Team as well as discussing the technical challenges encountered during this process.

Jan 1, 2010

By D. C. Lynch

While silica ores are generally considered to have little value, those with exceptionally low B and P content have, potentially, significant worth if processed for use in photovoltaics. The sales value of a cubic meter of ?run of the mill? silica sand is $42 per cubic meter (retail and delivered). If the silica sand can be used to produce solar silicon, its value after processing is $34,000 per cubic meter. Factors that impact the suitability of silica for direct processing in production of photovoltaics are examined.

Jan 1, 2010

By W. R. Huff

This report describes the development and operation by the Bureau of Mines of a pilot plant designed for using high-volatile A bituminous coal-in-water suspensions as a source of preheated coal and superheated steam in the pressure gasification of coal with oxygen. Figure 1 on page 2 is a block diagram of the integrated gasification process, in which a total of 70 tons of coal was fed from slurry and gasified. The present work included (1) development of equipment and methods both for mixing pulverized coal and water to produce slurry and for pumping and metering the slurry at gasification pressure; (2) development of equipment for heating the flowing slurry and, because slurry that can be pumped produces more steam than is necessary as a gasification reactant, developing equipment for removing and metering the excess steam; and (3) demonstration of the process under actual gasifier operating conditions, at a coal rate of about 800 pounds per hour and gasification pressures in the range 100 to 300 pounds per square inch gage. By using the forced-convection principle, a flow of slurry made from a caking, high-volatile A bituminous coal can be continuously heated to 600° F. in a coil-type heater. The flow rate and concentration of the slurry and the temperature gradient along the length of the heating coil must be closely controlled. In a radiant-type heater, involuntary reductions in flow rate, even momentary, can lead to coking and plugging of the heater coil.

Jan 1, 1961

By A. R. Harrington

BEFORE discussing some of the technical aspects of the steam generating plants of Nova Scotia Light and Power Company, Limited, it might be of interest to go back through history and see the development of steam generation in this public utility. Back around 1902 Nova Scotia Light and Power Company, Limited, had three slide-valve engines in-stalled at its Water Street, Halifax, generating station for a total capacity of 1,800 kilowatts. The plant remained at about this size until 1910 and in 1911 a 2,000 kilowatt steam turbine was installed to raise the total capacity of the plant to 3,800 kilowatts. In 1916, a 3,000 kilowatt turbine was installed and one of the slide-valve engines was removed to make a total plant capacity of 6,200 kilowatts. The total demand in the Company's service 8rea was at that time 4,000 kilo-watts.

Jan 1, 1958

By T. S. Golosinski

Introduction Typical dragline rigging includes several sets of ropes: hoist ropes, drag ropes, dump ropes and boom suspension ropes. The drag and hoist ropes contribute most to the dragline operating cost. Both work in very difficult conditions and wear out rapidly. As a result, frequent rope changes are required resulting in substantial cost and productive time loss. Although performance of rigging has a profound impact on dragline efficiency, there are no common, industry accepted standards related to its selection, operation and maintenance. Little information on the subject is available and the practice differs widely throughout the industry. The performance of drag and hoist ropes depends on: •rope construction that should closely match requirements of the specific application, rope operating conditions and its maintenance and • correct definition and application of the rope discard criteria so that full advantage of the rope can be taken without endangering safety of its operation. This paper reviews the present practice related to all these factors. Its findings are based on the wide survey of the present industrial practice. Field survey In total, 33 North American dragline applications were surveyed of which 17 were Bucyrus-Erie machines, 10 were Marion and six were Page (now P&H). Most of the draglines were stripping overburden in coal mines, but the survey also included some unique applications such as phosphate mining in Florida and oil sand mining in Alberta. Hoist drive power of the surveyed machines varied from 300 to 7775 kW (400 to 10,400 hp). Drag drives varied from 300 to 5815 kW (400 to 7800 hp). Boom lengths varied from 37 to 110 m (120 to 360 ft). Bucket sizes varied from 5 to 96 m3 (6 to 115 cu yd). The hoist and drag ropes installed on the surveyed machines were supplied by 10 rope manufacturers and differed widely in type and construction. Most common rope strand constructions included standard strands, Seale, Warrington, Warrington-Seale and Filler-Seale. Results of the survey [ ] Working conditions Working conditions of hoist and drag ropes are quite different. The first cope primarily with bending on rope drums, point sheaves and deflection sheaves, and with tension force imposed by the bucket and its load. The drag ropes are exposed to severe abrasion at the pit crest, and to severe bending and crushing at fairleads, all while coping with tension forces imposed by resistance of the bucket to dragging. Bending of drag ropes at house rollers and at rope drums is of minor importance for their performance. Differences in working conditions result in different wear patterns, which make it feasible to install discarded hoist ropes to further serve as drag ropes. The hoist ropes wear primarily due to fatigue breaks of wires, while the drag ropes are subject to severe abrasion of outside wires, rope deformation and internal wire-strand breaking. The last is often indicated by the reduction of rope diameter. The summary of working conditions for the surveyed draglines is shown in Table 1. For simplicity, Table 1 does not include the data on rope bending at the fairleads, nor at the deflection rollers and house rollers. Similarly, Table 1 does not include the data on drag rope bending (other than that on the rope drum), as its influence on rope life is insignificant in view of severe abrasion and internal wear taking place elsewhere. The following abbreviations are used in Table 1: [D - diameter of rope drum. DP - diameter of boom point sheaves. d - rope diameter x - mean value of the measured parameter. s - standard deviation of x B/d - average bending ratio of ropes B/d =(D+ DP)/2d n - operational safety factor of the rope (rope stength) x (number of ropes) n(bucket load + bucket weight)] In terms of D/d ratio, the working conditions of hoist and drag ropes are similar to that in other related industrial applications. However, the safety factors of the dragline ropes are lower, which requires them to carry relatively large tension forces. The last explains the fact that the life of dragline ropes is low when compared to other industrial rope

Jan 1, 1995

By J. L. Bowlby

Introduction In the following discussion, boiler-feed and mine waters will be considered from the point of view of the problems arising from the chemical nature of the mineral and gaseous impurities they contain. The theories underlying some of these problems will be reviewed for the purpose of getting a clearer concept of the problems themselves. Certain terms of a chemical nature, necessary to the discussion, will be explained on the assumption that they are not generally familiar to mining engineers. Finally, an attempt will be made to correlate theory and practice, with the abject of establishing certain limits to factors relevant to the problems, and to show that these limits are justified by practical experience. The general problems occasioned by the presence of mineral and gaseous impurities in boiler-feed and mine waters are: (1) Scale formation and corrosion in boiler systems. (2) Corrosion of mine pumps and pump fittings. These will be discussed separately. Boiler Scale Typical analyses of waters available for use in steam power-plants are given in the accompanying Table (Table I). All analytical data are expressed in grains per Imperial gallon. The bicarbonates of calcium and magnesium in the raw waters are shown as normal carbonates in the Table. Substances in the first five rows constitute the encrusting solids. All the waters listed in Table I would be classified as 'very good' in the schedule of classification for boiler waters adopted by the American Association of Railway Chemists in 1887. In spite of this classification, however, the waters contain sufficient encrusting solids to cause serious scale trouble after prolonged evaporation.

Jan 1, 1934

By R. S. Handy

THE properties of the Patiño Mines and Enterprises Consolidated, Inc., a New York corporation, are near Llallagua in the department of Chayanta in the west central part of Bolivia, South America, about 80 miles southeast of Oruro and 250 miles southeast of La Paz, the largest city in Bolivia and its virtual capital. The properties are accessible by railroad from three points on the west coast-from Mollendo, Peru, across Lake Titicaca, from Arica by way of La Paz, and from Antofagasta, Chile. The latter route, although the longest, is recommended by the companies as affording a more gradual introduction to the high altitudes; the mine being 13,000 ft. above sea level. The company operates its own railroad from its properties at Uncia to Machacamarca on the Chile & Bolivia R. R., a distance of 60 miles. This railroad is well equipped and well operated, and its location among the mountains surrounding Uncia represents excellent engineering skill. In fact all of the railroads, although they are of only a meter gage, are remarkable for the excellence of their construction, the arrangement of their dining and sleeping cars and the precision of their operation. There is only one drawback to rail- road and hotel accommodations and that is the absence of heating facilities, which does not seem to affect the natives but keeps a tenderfoot's teeth chattering continually. The company is a consolidation of the Patiño company, owning properties at Uncia, with the Compafiia Estanfera de Llallagua, a' Chilean corporation owning contiguous properties at Llallagua. Before the consolidation these companies were deadly enemies, and there still remain at the surface plant at Uncia the fortifications and underground defences provided during the warfare between the two factions. Also, in the Azul, or "Blue" tunnel at the junction line between the two properties is a strong steel barricade still bearing marks of the bullets fired during the various armed tilts between the workmen of the two companies. The headquarters for the mining operations and the milling plant have been moved since the consolidation from the original location at Uncia to the Llallagua side of the mountain, where the Chilean company's operations were carried on. The historic old town of Uncia, with its massive stone buildings of Spanish design, is a wreck, while the Llallagua side is being rapidly built up with modern structures.

Jan 1, 1929

By L. D. Smith

"This paper examines the impact of the various assumptions that go into an economic evaluation, and shows how these can be combined to show an exciting result that may not really exist. An example of an embellished case (the kind that one frequently sees when projects are being promoted) is developed and the cumulative impact is analyzed to show the actual project underneath. The paper also points out some areas to watch for overly optimistic assumptions such as prices, inflation, and debt. The concept of a “bare bones” base case is proposed (constant metal prices, constant dollars, no inflation, no debt, no interest, on a project basis, after tax) as a common reference point.As well, the discount rate is examined as one of the fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk."

Jan 1, 2002

Newcrest Mining is one of the leading independent gold producers in Australia thanks in large part to its Cadia Valley operations. It is the largest gold and copper producer in New South Wales and one of the largest in Australia. This year Newcrest will expand its operations with a A$545-million expansion in the area. The Cadia Valley is approximately 250 km (155 miles) west of Sydney. The province presently includes the Cadia Hill opencut mine and the Ridgeway underground mine. With a significant mineralized system to the east of Cadia Hill and a mineral resource below Ridgeway, Cadia Valley has the potential to underpin Newcrest?s production for up to 30 years. In 2007, total gold production for the company in-creased to more than 50 t (1.6 million oz) and cash flow increased by 47 percent, according to the company?s annual report. The history of mining in the area dates back to 1851, but Newcrest?s history is young. In 1990, Newcrest commenced activities in the Cadia Valley. In 1992, Cadia Hill was discovered, with the discovery of Cadia East (1995) and Ridgeway (1996) following close behind. In 1998, the Cadia Hill openpit mine was commissioned. In 2002, the Ridgeway underground mine was commissioned and in 2007 the company?s board of directors approved an A$545 million development of the Ridgeway Deeps. The Ridgeway underground mine is located adjacent to Cadia Hill. The Ridgeway orebody has no surface expression but lies approximately 500 m (1,640 ft) below the surface and resembles an inverted teardrop. It measures approximately 450 m (1,476 ft) by 250 m (820 ft) and extends in excess of 850 m (2,788 ft) in depth. Ridgeway is a sublevel caving operation. Crushed ore from underground is delivered by conveyor to a surface stockpile, adjacent to the Ridgeway concentrator. Using similar processes to the adjacent Cadia Hill concentrator, gold and copper are recovered in a conventional flotation circuit to produce a copper concentrate containing elevated gold levels. Ridgeway concentrate is combined with the Cadia Hill concentrate before it is pumped to the filtration plant in

Jan 1, 2008

By F. W. Wessel

This report summarizes Bureau of Mines laboratory tests of four tungsten¬-bearing materials of various grades, The test work has demonstrated that the dry reaction between sodium carbonate and scheelite is best conducted at 900° C. or a few degrees less. The sodium carbonate requirement, in addition to the stoichiometric equivalent of the scheelite, is in some inverse relationship to the grade of tungsten in the ore. Residence time and particle size exert a definite but minor control on the reaction. Pressure-digestion tests on an impure concentrate indicate the technical feasibility of extraction by this process. INTRDUCTION Over 100 years ago Oxland discovered that tungstic oxide could be removed from wolframite and converted to a soluble form by reacting the mineral with a soluble alkaline salt at elevated temperatures. He patented this discovery, and this patent 4/ since has been the basis for most tungsten extraction. Much literature exists on this process and its modifications, and the characteristics and possibilities of the reaction are quite well defined.

Jan 1, 1956

By Matthew John M. Krane

"The macrosegregation patterns and convective behavior of a Pb-5wt%Sb-35wt%Sn alloy are studied using new numerical treatments of solid particle motion and of transport phenomena occurring during the solidification of ternary metal systems. At this composition, the solidification which occurs while the local liquid composition is in the (Pb)-(SbSn) binary eutectic trough has a significant effect on these phenomena. The effects of this solidification path on fluid flow and macrosegregation are compared to the more familiar binary alloy patterns and the effect of solid particle transport is evaluated. The final predictions of macrosegregation are compared to measured composition profiles. IntroductionThe macroscopic maldistribution of alloy constituents during solidification, commonly called macrosegregation, is a defect which occurs in real metal processing systems. This nonuniformity of species distribution, especially when it forms a high composition gradient or a poor distribution of secondary phases, can lead to areas of high stress concentration, which contribute to cracking during extrusion or forging of wrought alloys or when an as-cast piece is severely loaded in service [1, 2]. Macrosegregation studies in binary systems have become quite common since the introduction of single-domain numerical models which feature one set of conservation equations and boundary conditions for an entire, fixed computational domain containing solid, liquid and multiphase regions. A complete review up to 1995 has been presented by Prescott and Incropera [3]. However, most commercial alloys generally have more than two species in amounts significant enough to affect the convective flows which lead to macrosegregation and other defects. The formation of secondary solid phases, including eutectic and peritectic reactions, also may occur in commercial metal alloys and should be treated using appropriate thermodynamic models."

Jan 1, 1999