Search Documents

By M. L. Harris

Explosions in underground mines and surface facilities such as processing plants are caused by confined accumulations of combustible dust and/or flammable gas mixed with air in the presence of an ignition source. Underground explosions can be prevented by minimizing methane concentrations through methane drainage and ventilation, by adding sufficient rock dust to inert the coal dust, and by eliminating ignition sources. The effectiveness of rock dust in arresting explosion propagation was proven by experiment and practice (1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11). The precise mechanism by which rock dust (generally pulverized limestone dust) quenches flame has not been fully explained, but is believed to be absorption of thermal energy from the heated gases and absorption of radiant energy, which reduces the preheating of unburned coal particles ahead of the flame front. One measurable aspect of explosibility is incombustible content. In order to determine whether enough rock dust is applied, 30 CFR1 § 75.403, Maintenance of Incombustible Content of Rock Dust, requires at least 80% incombustible content on the roof, ribs, and floor of underground coal mines. 30 CFR § 75.403-1 further defines the incombustible content as follows: ?Moisture contained in the combined coal dust, rock dust and other dusts shall be considered as a part of the incombustible content of such mixture.? In order to determine the incombustible content of the mine dust, samples of deposited dust from specified areas in a mine must be collected, analyzed, and then compared with the minimum standard of 80%. The traditional low temperature ashing (LTA) approach to determine if a coal and rock dust mixture is compliant with the inerting requirement consumes the coal dust and considers the remaining material to be inert. Compliance with the law is then determined by comparing the measured percentage of inert material of the representative band sample with the pre-established requirement of 80%. The incombustible content of the sample includes rock dust, the amount of moisture as received at the lab, and the inherent ash in the coal. The LTA method is not itself a direct measure of explosibility but is a surrogate that calculates a single parameter associated with large-scale Bruceton Experimental Mine (BEM) explosion test results conducted with dry rock dust. This method assumes a homogenous mixture with no layering of rock dust and coal dust. Float coal dust is a serious explosion hazard if it accumulates on top of the rock dust and is not mixed with the rock dust (12). Mitchell and Nagy (13) studied the effectiveness of water as an inerting agent for the coal dust explosion hazard. The study emphasized that surface water evaporates readily from dusts. Thus, in a passageway where the dust is wet, changes in weather or the ventilation system could dry the dust and make it unsafe in a relatively short period of time. Where adequate rock dust has been applied, this drying effect is not a factor. However, if the mine depends upon the moisture content as part of the incombustible content, fluctuations in the dust surface moisture within a mine can render moisture content an ineffective and inconsistent measure of safety. Additionally, if sufficient moisture is absorbed and subsequently relinquished by rock dust, a cake can form and render the rock dust ineffectual. The trend has long been recognized that mine explosions occur primarily during the winter season when the humidity is low for long periods of time (14, 15, 16). In light of this trend and due to the potential variability of the moisture content of the dust, it may not be prudent to include variable surface moisture in the total incombustible content of the sample. Instead, surface moisture should be viewed as an additional safety measure as long as the rock dust is dispersible. However, moisture limits the ability of the rock dust to disperse and can significantly reduce its capacity to effectively inert propagating explosions (2, 13, 17, 18, 19, 20, 21, 22). Given the methods by which the as-received moisture and incombustible content are determined, dust samples from the 2010 MSHA database were assessed to determine the variability of the moisture content throughout a year and how often the measured as-received moisture might have affected the dust explosibility determination if removed. The findings were then verified by observation in laboratory studies and within the NIOSH OMSHR Safety Research Coal Mine (SRCM).

Feb 23, 2014

By M. G. Lipsett

"Mining properties are becoming increasingly remote, a challenging situation for operating and maintaining equipment. Logistics of transporting workers and materials can be alleviated by having timely, accurate information of equipment location and operating condition, and by automating some activities. This paper discusses an infrastructure for remote operations, with strategies for communicating different types of data, and a design method so that systems can interact with either an operator or another system. A remotely operated excavator prototype is described, with on-board performance and diagnostic monitoring systems now used on production equipment. IntroductionSyncrude Canada Ltd. operates an openpit oil sands mine near Fort McMurray, Alberta. For twenty years, draglines and bucketwheel reclaimers have fed conveyors that transport dry oil sand to an extraction and upgrading plant. In converting to a truck and shovel operation, Syncrude has developed slurry pipelines and bitumen froth pumping to allow more remote leases to be mined more than 30 km from the base plant.There are organizational and resourcing challenges in operating and maintaining equipment in three nearby, but separate, mines. The logistics of transporting workers and materials to production and support equipment become more difficult, and operations and maintenance personnel and facilities become more distributed. Supervising mine operations will rely even more on having timely, accurate information about equipment location and operational status.Syncrude is typical of an open-pit operation. Voice communications are the preferred way to exchange information for making immediate decisions about operations and maintenance. A large number of narrowband FM broadcast radio channels keep teams of miners working together. Haul truck drivers, shovel operators, and dispatchers talk on one channel while maintainers coordinate activities with the control tower on another. Cellular phones have become popular for supervisors who have to talk with planners and engineers in offices without radios."

Jan 1, 2000

By H. Hoberg, M. Langen, B. Hamacher

Since the term "abandoned hazardous sites" was first coined in the 1978 environmental report of the Council of Environmental Specialists, a number of different types of technology has been developed in the Federal Republic of Germany for the remediation of contaminated soils /l/. At former sites of the mining industry, such as metallurgical and coking plants whose soil has been contaminated by organic and inorganic pollutants over decades of industrial activity, there is an exceeding necessity for soil remediation. Also, many former locations of metal processing works, battery factories or scrap yards have been contaminated in particular by heavy metals. Wet mechanical soil decontamination has proven successful over the past 10-15 years in the purification of these soils The process goal is the enrichment of the pollutants in certain plant products and the separation of a pollutant concentrate from the decontaminated soil. Table 1 lists the steps of the highly advanced wet mechanical soil decontamination process to achieve this process goal. Table 1 lists both the name of each process step and its goal in terms of a direct separation of the pollutant or the preparation of the soil for subsequent separation steps. For the separation of heavy metals, density sorting and separation techniques utilising flotation were specifically used. The use of chemical auxiliaries such as acids and lye is limited to special cases because these in themselves produce additional environmental impact and the economical effficiency of these techniques compared to conventional methods is lowered by supplementary process steps for water purification. The subject of this presentation is to consider how soil decontamination processes can be effectively improved through a description of the material properties of soils contaminated by heavy metals, and through carrying out basic investigations about the adsorption of heavy metals. Soils of different origins, especially those from former mining and metallurgical sites, were used for the experiments.

Jan 1, 1995

By Jeane Hull

Jan 1, 2009

By Northcutt Ely, Charles F. Wheatley

This chapter deals with the systems of laws by which governments regulate the exploration for and production of the minerals within their jurisdictions. It is a summary, restricted by necessary space limitations, of material assembled by the author for a forthcoming publication of the United States Bureau of Mines, "Summary of Mining and Petroleum Laws of the World." (Information Circular, 1959.) The present study is organized in three parts, dealing with (1) the historical background of these legal systems, (2) laws of the United States, and (3) laws of other countries of the world. The reader's attention is invited to the acknowledgments at the end of the chapter, which inadequately express the appreciation due those who have assisted in the collection of this material. Part I. Historical Development of Major Western Systems of Land Tenancy with Respect to the Ownership and Control of Minerals The use of metals in primitive societies was largely confined to the manufacture of weapons for self-preservation. The ruler's control over copper, then brass, then iron, was essential to maintenance of his own ascendancy at home and his group's position against neighbors who had access to similar metals. Ancient societies were thus characterized by the ruling group's ownership of minerals and metals. The Egyptian civilization, which emerged in the fourth millenium B.C. upon the agricultural subjugation of the lower valley of the Nile, was responsible for extensive development of the upper valley as a source of mineral wealth. The production of gold during the height of that civilization has been estimated at $30,000,000 per year, thus equaling the early placers of California and Australia. The mines of Egypt were the property of the Pharaohs and were controlled at their direction. Greek mining developed a different scheme of land tenancy which more closely resembled modem concepts. Development of mineral resources was

Jan 1, 1959

By Liu Liu

In the recent 10 years the rapid development of Chinese steel industry has attracted the attention of the world. The technological progress of converter steelmaking has played an important role in this process. First of all, slag splashing has been extensively adopted by Chinese steel companies in various sizes of converters from largest to smallest ones, and even including those using special hot metal containing V and Ti. Remarkable metallurgical results have been achieved. Up to now the average converter campaign life has reached nearly 10,000 heats, and the longest exceeds 30,000 heats in three melt shops. Based on this process, the long-life combined-blowing converter steelmaking technology has been developed. Slag splashing has been used to form a gas permeable "slag mushroom" on the top of bottom nozzles to protect the nozzles. In order to keep the effective bottom blowing, furnace bottom thickness control technique has been developed to prevent the furnace bottom growth. It makes the service life of bottom nozzle the same as the converter campaign life (average 10,000 heats and longest > 30,000 heats). The complete combined blowing was ensured through out the furnace campaign. Concentration product [C][0] is in the range of 0.0023 ~ 0.0030%, the T.Fe in the slag is lowered by 4 ~ 6%, and the [0] in steel is decreased by 100 ~ 250 ppm.

Jan 1, 2004

By P Mikula, B Darlington, J Graham, P Young

In underground mines experiencing dynamic events, there is an ever-present challenge to design and maintain a capable ground support system. One key component of ground support systems is surface support, which serves the essential roles of retaining failed rock and transferring forces generated by surface displacement to rock bolts or other support elements. Observations underground show that in many instances, standard mesh panels alone do not provide sufficient dynamic support to retain substantial bulking failures imposing displacement onto mesh, and in such cases Mesh straps and W-straps may be employed. Determining the performance of surface support elements proves to be difficult, with a multitude of variables at play in the underground environment. Quite comprehensive work has been completed on laboratory testing of surface support systems; however, very little work has been conducted on in situ dynamic testing of Mesh straps and W-straps. In 2019 in Western Area’s Flying Fox Mine, in situ dynamic testing was conducted on a series of Mesh straps and W-straps using Sandvik’s in situ Dynamic Test Rig (DTR). The testing regime applied impact energies from 5.1 to 15.3 kJ to Mesh straps and W-straps. The performance of the straps that did not fail was a maximum absorbed energy of 9.3 kJ and 14.2 kJ for the Mesh straps and W-straps respectively. The testing successfully demonstrated the ability of Sandvik’s DTR to test not only rock bolts, but also surface support elements, creating new testing and research possibilities. The testing also provided important design guidance data that is not practicable to obtain using laboratory dynamic testing facilities.

Nov 29, 2022

By Thomas C. Denton

The Old Reliable copper mine was first examined by Harlow D. Phelps , an engineer of the Bureau of Mines , in October and November 1942 , in compliance with a request from the War Production Board , which furnished copies of assay maps of the 100- and 200-foot levels and requested that they be check-sampled . The author and R. li. Grantham and W. D. Hughes , engineers of the Bureau , made a second and more detailed examination later , after a number of manways had been opened that were inaccessible when the first examination was made .

Feb 1, 1947

By Weida Guo, Sangsang Liao, Bart Blanpain, Muxing Guo, Qing Liu, Lingling Cao, Keshe Ren, Yannan Wang, Lefei Sun

The interaction between a supersonic oxygen jet and liquid metal is a dominant factor affecting transport phenomena during the converter process. A systematic description of the interaction is of significant importance for a quantitative understanding of the transport phenomena. In this paper, cold model experiments and the corresponding numerical simulations were carried out to investigate the gas-slag-metal interaction inside an 80 t BOF converter. The effects of the operation parameters, such as inlet pressure, slag thickness and slag viscosity on the multiphase interaction have been studied. It has been found that the cavity profile is closely related to the operational conditions. The cavity depth increases with an increase in oxygen inlet pressure, whereas the cavity width is much less affected. The cavity profile is also clearly influenced by the thickness of the slag layer. The influence of slag viscosity on cavity profile is not significant under the present simulation conditions.

Mar 1, 2018

By John W. Buch

In 1947, a Korfmann universal shearing machine was installed in a mine in the Southern field of the Pennsylvania anthracite region. The machine was obtained from Germany by the Bureau of Mines after the close of World War II as a part of a program of experimental work to increase the output and lower the cost of anthracite, which the Bureau of Mines initiated in 1944 when an agreement was made with an anthracite-producing company for use of one of the company's mines as a testing ground for certain mechanical equipment procured or developed by the Bureau. A major objective is to develop a mechanical mining method that will increase the rate of advance and reduce the coat of development of coal gangways in steeply pitching seams. In addition to the time to be saved in driving these openings by machine, it is felt that further economies will be affected by making it possible to concentrate producing sections into smaller compass and that savings will ensue in supervision, maintenance, and time required for mining a section. A higher percentage extraction also is an objective. Test work covered by this report was concentrated on the power characteristics, maneuverability, effectiveness, and general qualities of the Korfmann machine in cutting coal, the cutting tests representing the first use of a machine of this kind in steep-pitch mining in the United States.

Jan 1, 1951

By D. R. Reeves

This paper describes the geophysical Jogging of coal that is being carried out for the National Coal Board in the United Kingdom. An explanation of the technique is given and results are presented showing estimations of seam thickness to within ±0.5 in. and ash content to accuracies of ±2.5 per cent. The basic method of interpretation is outlined and some conclusions regarding the conditions of roof and floor material which may be deduced from the logs are explained. An indication of future developments in this field, including the identification of coal type and moisture content, is given.

Jan 1, 1971

By J. M. Sabio, A. W. Stalberg

Keywords: Pyrometallurgy, furnace, calcium carbide, acetylene, Newcastle The manufacture of calcium carbide in Newcastle, South Africa, was started in the late 1950s by a company called South African Carbide, at the Ballengeich site. In 1978, this operation was bought by the forerunner to the present AECI Ltd, a large producer of commodity chemicals at the time. Production continued at this site until 1992. In the meantime, Karbochem, an operating division of Sentrachem Ltd, was also manufacturing carbide in Newcastle, as a building block for the manufacture of synthetic rubber. In 1990, the Karbochem calcium carbide operation was closed down. In 1992, the AECI carbide business and the Karbochem production facility were amalgamated, and production continued under the Karbochem name. In 1997, the Dow Chemical Company bought the holding company of Karbochem, and the carbide business continued operations until 2003. In June 2003, the business was sold to a management consortium as SA Calcium Carbide (Pty) Ltd. Later, in October 2004, 100% of the shares were acquired by the Andina Group. Today, the Andina Group, consisting of SACC from South Africa, CIL from UK, and ANDINA from Argentina, has become a global leader in the manufacture and supply of calcium carbide and calcium silicon, ferro silicon 75% and derivatives, recarburizers with low nitrogen content, acetylene, carbon black, micro-silica, and silicon metal. The production facilities at Newcastle comprise a 52 MVA submerged arc furnace of a closed design, carbon monoxide gas recovery, recovery of fine raw materials via a hollow electrode system, and an extensive computer-controlled process. These all enable an efficient state-of-the-art operation. The downstream processing facilities consist of screening and drumming facilities, milling facilities, an acetylene generation plant, and an acetylene carbon black plant. Clearly, SA Calcium Carbide (Pty) Ltd has a long history of supplying quality calcium carbide to the industries that it proudly serves.

Jan 1, 2006

By G. Mike Bernard

The Andacollo gold mine is located near the town of Andacollo (population 14,000 people) in Chile’s region four. It is about 56km (35 miles) by paved road from the coastal city of La Serena. Santiago is about480 km (300 miles) south. Site elevation varies between 1,000 and 1,280 m(3,300 and 4,200 ft). The climate at the Andacollo site is moderate but arid. Average annual rainfall is only 130mm (5 in.). Because there is little rain and the temperature varies only a few degrees (14 to 24 C or 57 to 75F), there are no problems with freezing, solution dilution or pad saturation. The climatic conditions are ideal for heap leaching.

Jan 1, 1996

By Paul L. Broughton

"IntroductionThe coal deposits, all of lignite rank, of economic interest in Saskatchewan are associated with the Ravenscrag Formation (Paleocene). Several Cretaceous formations have less significant lignite accumulations (Broughton, Irvine and W'hitaker, 1974). The Swan River Group (lower Cretaceous) and Judith River Formation (upper Cretaceous) have the only coalbearing strata in the shallow subsurface of central Saskatchewan. The Swan River Group coalfield is relatively small and underlies only 15 sq km of the surface approximately 40 km south of La Ronge, Saskatchewan. An estimated 36 billion short tons are within 45 m of the surface. No reserve estimates are known to have been calculated for the coal-bearing Judith River Formation exposed at the surface in the vicinity of the South Saskatchewan River valley in west-central Saskatchewan. Although no coalfields have been delineated, lignite beds up to 1.8 m thick have been intersected in test holes. The coal-bearing upper Cretaceous and lower Tertiary strata of the northern Williston Basin extends the full width of southern Saskatchewan for 650 km, and from the United States border 120 km north to 50° latitude (Fig. 1). Only the coalfields of the Ravenscrag Formation, because of their economic interest, will be considered further. There are four major coalfields. They are, from east to west: Estevan, Willow Bunch, Wood Mountain and Shaunavon (Cypress) coalfields. Cumulative lignite seam thickness for each basin is 10 -15 m (Figs. 2 and 3). The origin of each coal basin, resource calculations, seam stratigraphy, and mining activity are discussed. Regional Setting The Williston Basin is an ellipsoidal depression in the Precambrian basement, centered in western North Dakota and marginal to the exposed craton of northern Saskatchewan and central Manitoba (Fig. 1). The sediments of the basin range from Cambrian to Pleistocene in age and have a maximum known thickness of 4614 min western North Dakota. A maximum of 3200 m is recorded in southern Saskatchewan. Most structural deformation is late Cretaceous to early Tertiary (Paleocene) in age, coinciding with the Laramide Orogeny. The pre-Laramide Williston Basin, with a depocenter near Williston, North Dakota, began developing during the middle Ordovician, or possibly earlier."

Jan 1, 1985

By A H. Gray

Gekko Systems Pty Ltd engaged in the test work, design, manufacturing and commissioning of the pre-concentration plant at Silver Standard Resources Inc’s Pirquitas mine in the north western Jujuy province of Argentina. Testing of the ore at coarse feeds of between 2 and 12mm returned probable recoveries of up to a total of 95% silver into 50% of the mass fed to the InLine Pressure Jigs (IPJ’s). The plant has been designed and built based on the test results to include a preparation screen to bypass the fines that are naturally higher in grade and repulping of the coarse which is then pumped to three parallel trains of 2-stage IPJ roughing-scavenging. The target 50% yield to concentrate passes over a dewatering screen and the solids are returned back to the mill feed conveyor. The IPJ tails are transferred to a dewatering screen and solid rejects are stockpiled off the end of a transfer conveyor. All dewatered underflow products are processed via hydrocyclones to recover dirty water for use back into the IPJ circuit and return entrained fines to the fines bypass line.With the sulphide orebody being processed, the results from operations to date have shown that plant performance is matching the original laboratory sulphide ore testwork data. The objective of the pre-concentration step is to both reject gangue and achieve grades between 300-400g/t Ag to the float circuit as flotation recoveries are maximised within this range. The plant currently achieves overall upgrades of approximately 150% of feed grade with the IPJ only circuit producing an average 180% increase from calculated feed grade.

Aug 8, 2011

"The Detour Lake Mine is located in northeastern, Ontario, approximately 300 kilometres northest of Timmins and 185 kilometres by road northeast of Cochrane. The mill processes a free milling gold ore using both gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 55,000 mtpd at 95 microns with the addition of pre-crushing upstream of the SAG mill.The present paper will describe the methodology used to successfully prove that gold of the Detour Lake Mine ore is mostly concentrated into the fine size fraction of the blasted rocks. It will describe the various options possible to create value from this ore property.IntroductionThe purpose of this test work was to determine the grade of the pebbles and consider if there was value into discarding the pebbles and replacing the material by fresh feed.1. Pebble samplingThe pebbles were sampled and assayed for grade every day for 3 months. After 3 months of sampling, the results showed that the pebbles only carried 28% of the fresh feed grade. This phenomenon can possibly be explained by the fact the gold is located into area of fracture in the rocks.January-March 2014 – Pebble assay average• Line #1 = 0.222 g. Au/t• Line#2 = 0.275 g. Au/t• Head grade = 0.88 g. Au/t2. Crushing and grinding circuit surveysWith the above information, a grinding circuit survey was planned. The purpose of the survey was to build a JKSIMMET model of the grinding circuit for mill optimization but also to understand the deportment of gold into various size fractions that may explain why there is so little gold in the pebbles. All streams and size fractions was analysed for particle size analysis and for gold.Since Detour has dual grinding lines, both circuits were sample at the end of May. Two supplemental survey of the secondary crushers were also done and a survey of the gyratory crusher."

Jan 1, 2016

By Shigeomi Nishigaki

This paper presents quantitative indexes to evaluate operator?s bearing, difficulty in a task, and machine operability when an operator remotely controls a backhoe, and reports the use cases. The quantitative indexes would give her/him the opportunity to reflect on her/his works, and enable us to gain in-depth insight into the teleoperation, and furthermore give us with promising hints to improve it.

Aug 1, 2013

By Peter Kowalczyk

Magnetic surveying and map production is well established in land based mineral exploration. Magnetic data are routinely used to map geology in covered terrains, to estimate the depth to basement in overburden covered areas, and to identify altered zones, mineralization, bedding attitudes, and fault networks both regionally in map view, and through interpretation to depth in 3D. Best practices for magnetic survey methods and magnetic interpretation exist in all areas of land based geophysical survey methodology - mineral exploration, hydrocarbon exploration, geological mapping, archeological mapping, and in military applications. At sea, and particularly under the sea, sophisticated magnetic surveys are being done, but it can be argued that these are primarily in niche applications, for example in naval mine-hunting and UXO applications. Magnetic data is not normally collected on AUVs and ROVs conducting mapping and hydrographic survey operations. OFG has developed physical and mathematical calibration routines so that magnetometers can be mounted directly onto AUV and ROV bodies where significant heading errors and magnetic gradients exist. This simplifies the routine deployment of magnetometers on AUVs and ROVs for mineral exploration and other magnetic survey applications without the need for towed bodies, ungainly mounting frames, or degaussing of the survey equipment. Our experience shows that magnetometers can be operated routinely on AUVs and ROVs and that with careful processing useful maps can be produced routinely at low cost.

Sep 1, 2014

This paper on the relation of Granite and Sedimentary Contacts to Victorian Mining will, it is hoped, be of interest to members of the Institute.The broad fact that gold often occurs' at or near the junction of granite with sedimentary silurian or metamorphic rocks has been noted by some Victorian geologists, miners, and prospectors; but the fuq practical value -of the fact does not seem to have been fully realised by prospectors. Glancing at the Geological" Map of Victoria, one can see that many of our goldfields 'are situated at or near the junction of granite with Palceozoic sedimentary formations, and that some of our alluvial fields are on granite. Many prospectors are possessed of this knowledge but when prospecting a contact locality, they would be just as likely to confine their search for auriferous matrices to spots a quarter of a mile on the sedimentary side, as on the actual contact line of two formations.

By R. W. Raymond

(Chattanooga Meeting, October, 1908.) THE immense commercial value of the Gayley dry-blast process has been established beyond controversy. The testimony of practical blast-furnace managers, on both sides of the Atlantic, agrees that it reduces the cost of pig-iron about $1 per ton; but from the same testimony it appears that this direct economy does not by any means cover its commercial advantages-in fact, that under conditions frequently encountered in practice, it presents other benefits of even greater immediate financial importance. To this point I shall recur in a later part of the present paper. The history of the reception given to this invention, especially on the other side of the Atlantic, has repeated an experience familiar to American engineers. First, the reports of our practice were rejected as theoretically impossible, according to generally accepted notions and formulas; then the figures were reluctantly accepted ; and finally the attempt has been made to explain how they could have been obtained. As to the Gayley dry blast, we Americans have been for several years in the last stage of the discussion, and the rest of the professional world is rapidly coming to it. Meanwhile, the remark has been repeatedly made that, whatever Mr. Gayley's process may turn out to be worth, it was not an invention on his part, but simply the energetic and persevering execution of a procedure already proposed by others. This question I wish to discuss first in the present paper. I. WHAT DID MR. GAYLEY INVENT Realizing that this is not the place for detailed argument on an issue of patent law, I shall not undertake to quote and criticise the publications prior to Mr. Gayley's first patents. It may be admitted, without such critical analysis, that the possi-

Jan 1, 1909