Search Documents

By G. R. Fitterer, C. H. Herty

"INTRODUCTION Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis in easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot—top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel.For a large tonnage of steels which go into articles manufactured by deep—drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low—carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, — that is to say, deoxidized with manganese and perhaps a small amount of aluminum, — the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper—central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low—carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel. These defects would be minimized by clean killed steel."

Feb 1, 1931

By Gamal Rashed, Zorica Radakovic-Guzina, Khaled Mohamed

"Underground coal mines use mechanical bolts in addition to other types of bolts to control the rib deformation and to stabilize the yielded coal ribs. Limited research has been conducted to understand the performance of the mechanical bolts in coal ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted this work to understand the loading characteristics of mechanical bolts (stiffness and capacity) installed in coal ribs at five underground coal mines. Standard pull-out tests were performed in this study to define the loading characteristics of mechanical rib bolts. Different installation torques were applied to the tested bolts based on the strength of the coal seam. A typical tri-linear load-deformation response for mechanical bolts was obtained from these tests. It was found that the anchorage capacity depends mainly on the coal strength. Guidelines for modeling mechanical bolts have been developed using the tri-linear load-deformation response. The outcome of this research provides essential data for rib support design.INTRODUCTIONThe design of rib bolting in U.S. coal mines is based on a trial-and-error process, which is insufficient to eliminate injuries and fatalities caused by rib falls. In the last 10 years, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States (MSHA, 2018). Recently, NIOSH researchers surveyed 90 sites in 14 underground coal mines in the Eastern United States and found that 11 mines are bolting coal ribs, with 4 of those mines using the conventional mechanical bolts and the others using fully-grouted bolts. NIOSH researchers are developing an engineering design procedure for rib support. Pull-out test programs for mechanical and grouted rib bolts were conducted to understand the rib control mechanisms of rib bolts. Only the test results of mechanical bolts are presented in this paper.Mechanical bolt (or point-anchored bolt) is a tensioned bolt anchored down the borehole with a mechanical expansion shell or a resin-grouted medium (Peng and Tang, 1984). The mechanical anchor bolt consists of a plug, a shell anchor, a headed bar with the top end threaded, a bearing plate, a hardened washer, and occasionally a friction-reducing washer. The shell anchor can be either standard or bail type (Figure 1). The standard type shell is held in place by a nut, while the bail anchor uses a strap to hold the shell in place (Peng, 2008). The diameter of the bar is generally 16 mm (? in) for the #5 bolt or 19 mm (6/8 in) for the #6 bolt. The diameter of the hole that the bolt is inserted into must be carefully controlled, since an oversized hole can result in poor anchorage (Moss, 1971). The anchorage is obtained by applying torque to the bolt head, which in turn pulls the plug down in the shell and expands the serrated leaves against the sides of the hole-wall. In the resin-grouted anchor, the resin replaces the mechanical expansion shell at the end of the hole. The anchorage is achieved by bonding between the resin, bolt, and the hole-wall."

Jan 1, 2019

By H. Meseck

Dynamic pile test methods to establish the bearing capacity of driven piles were developed in the USA more than 20 years ago. In the Federal Republic of Germany, the first dynamic pile tests were carried out at the end of the 70's. Today dynamic pile tests are successfully used to establish the integrity and bearing capacity of driven and bored piles. The Institute of Foundation Engineering and Soil Mechanics at the Technical University of Braunschweig has developed its own method of measuring and evaluation for the execution of dynamic pile tests. The principles of the dynamic pile tests, the measuring and evaluation plant as well as the experience gained with it in the examination of cast-in-place piles are presented in this contribution.

Jan 1, 2010

By D. F. Boyd

On April 10, 1958 a new 7500 long ton/day iron ore beneficiation plant went on stream producing an average of 3000 long-tons of high quality concentrate a day. Plant operates on two, 12-hour shifts is six days per week, The new mill end crust ink plant were built adjacent to the company's open pit dining operate on at Bomi Hills, Liberia. The mall is essentially a gravity concentrator employing crushing, and grinding to liberate the mineral values, followed by concentration in Humphreys spirals. The cleaner spiral tailings are re-ground and tabled to recover additional iron values. Ire addition to. this mills the company operates a crushing and screening plant for the high grade direct shipping ores

Jan 1, 1962

By J. P. Messervey

Dr. K. A. Clark: No one will doubt the statement of fact that, during drilling operations through the bituminous sand beds in the Mildred-Ruth Lakes area, the core-barrel was found to contain bitumen with minor amounts of sand instead of bituminous sand. But many will doubt the interpretation of this fact as meaning that beds of bitumen occur interstratified with the bituminous sand beds. They will prefer to hold faith in the laws of physics, which deny that sand will float on oil or that fluid under pressure will not flow away through a permeable medium, until it is proved that the appearance of the oil in the core-barrel was not due to circumstances surrounding the drilling of the bituminous sand beds. The implication of the interpretation that sand is floating on oil is clear and it is unacceptable. Bituminous sand is unconsolidated sand more' or less saturated with a viscous oil. It is as difficult to conceive of bituminous sand lying on top of a body of the viscous oil as it is to conceive of unconsolidated sand more or less saturated with water lying on top of a body of water. The only difference between the two concepts is that the oil is viscous whereas the water is fluid. Oil-soaked sand placed on viscous oil would, when released, sink through the oil slowly, whereas water-soaked sand would sink through the water quickly.

Jan 1, 1947

By A. W. Deurbrouck

This report describes the preparation characteristics of the significant coalbeds from which samples could be obtained in Webster County, W. Va. In 1964, approximately 825,000 tons of coal was produced in the county, of which 732,000 tons was mechanically cleaned in three preparation plants. The Sewell coal bed accounted for 94 percent of the coal produced. Twelve samples were collected from five coalbeds. Four of the samples would require upgrading to meet metallurgical requirements; two others of just over 8.0 percent ash would require some upgrading. In general the coalbed samples collected in the county were of medium-sulfur and medium-to low-ash content as received or after removal of the sink 1.58-specific-gravity material.

Jan 1, 1966

By D. R. Walker, M. C. Shaw

Dimitri Kececioglu (Allis-Chalmers Manufacturing Co., Milwaukee)—The idea of applying metal cutting theory to comminution and vice versa is very impressive. Among others, the demarcation of wheel-grinding data into two regions, namely Kick's and Rittinger's, draws attention here. A study of Figs. 6 to 9 shows the following: In Fig. 6, 1 point out of 8; in Fig. 7, 4 points out of 26; in Fig. 8 only 1 point out of 13; and in Fig. 9 practically none out of 13 points fall out of curve No. 2. Also when grinding particles smaller than 5x10." in. it is difficult to measure very accurately the grinding forces, chip geometry, and particle size. In view of the above it would be difficult to make a positive and distinct demarcation of the Wheel-grinding data into two regions, namely, Kick's and Rittinger's. The idea of using machine grinding to determine the comminution properties of materials is indeed unique. The following cautions come to mind, however, regarding applicability of machine grinding data to comminution: 1—Grinding gives uniform particle size, whereas comminution gives a variety of particle sizes in the same process. The fact that grinding gives uniform particle size is not necessarily an advantage because in comminution the overall energy under actual comminution is desired and comminution invariably results in the production of a variety of particle sizes. 2—In grinding, a small particle is ground off a comparatively large surface. In comminution small bodies are broken down to smaller bodies. This makes it difficult to establish a concept of reduction ratio in machine grinding. 3—The mechanics of machine grinding involve direct shearing action under very high strain and comparatively high compression at the shear zone, whereas: comminution involves direct dynamic compression and surface friction with comparatively little strain and shear. Consequently the mechanics of machine grinding appear to be different from those involved in comminution. Hence one might arrive at erroneous con- clusions when comminution characteristics are eval-uated from machine grinding results. It is noticed also that functions other 'than Eq. 16 which do not involve the concept of direct proportionality of useful energy input to new surface area created (Eq. 2 and particularly Eq. 12) may be derived to fit the, data of curve No. 2. One such relationship may be u = ct-", where c is a positive constant and n is a positive constant less than unity. This, of course, is made possible because data of a very small range. of particle size are being fitted by the curves of No. 2 and the hereby suggested relationship. A sound comminution theory should be applicable to a relatively large range of particle size. George B. Clark (Department of Mining Engineering, University of Illinois)—While the experimental work of Walker and Shawin this article is of intrinsic value in revealing certain fundamental aspects of machine grinding, milling, and related processes and in adding to the store of information concerning the comminution of solid materials by this particular process, it appears doubtful that the results of their research can be employed to verify either Kick's or Rittinger's theories. Both these laws were originally developed and proposed on the basis of very simple, idealized hypotheses. The creation of parallel idealized physical laboratory conditions which would be required for either their proof or disproof appear to be well beyond the scope of human ingenuity, at least at present. One great weakness of the imputed verification is that the spread of the points plotted on the graphs is not sufficient to permit accurate 'curve fitting. The range of particle sizes included in the belt and wheel grinding is not extensive enough to show any general trends, particularly for the horizontal portion of the curves, said to represent Kick's laws. That the milling; grinding, and turning data obtained by Walker and Shaw for both metals and minerals happen to comply with. certain interpretations of these two theories under certain specialized conditions

Jan 1, 1955

By W Valery, S Morrell

In the mining industry blasts are usually designed to fracture the in situ rock mass and prepare it for excavation and subsequent transport. The run of mine (ROM) fragmentation is considered good when it is fine enough and loose enough to ensure efficient digging and loading operations. Mining optimisation strategy is hence usually focussed on minimising total mining costs and maintaining these ROM fragmentation characteristics. Although this approach ensures an efficient mining operation it ignores the potential impact on crushing and grinding. Investigations by several researchers have shown that designing blasts to produce ROM fragmentation to optimise crushing and grinding performance enhances the overall efficiency and profitability (Eloranta, 1995; Kojovic et al, 1995; Bulow et al, 1998; Kanchibotla et al, 1998; Scott et al, 1998; Simkus and Dance, 1998). Field experimentation in this area is often found to be difficult because of high implementation costs and insufficient understanding about the effect of fragmentation at different stages in a comminution circuit. Modelling and simulation of blasting and comminution processes provide a more economic alternative to explore the impact of blast design changes on the down stream operations (Kanchibotla et al, 1998; Kojovic et al, 1998; Adam and Siddall, 1998; Bulow et al, 1998). However, the reliability of such simulations depends on:the ability of the models to reproduce the physical processes that take place; characterisation of rock mass in terms of its blastability and comminution characteristics; and in the case of blast modelling the ability to predict fines (-10 mm) has been found to be particularly important as this fraction has a significant effect on mill throughput.

Jan 1, 1999

By Marcos Villegas

El presente texto describe el desarrollo del sistema de gestión de riesgos en la reingeniería de procesos, justificando la inversión en gestión de riesgos de la concentradora Atacocha donde se protege a las personas, activos e ingresos, minimizando el potencial de pérdida de los riesgos y así proveer fondos para recuperar las posibles perdidas y soportar el sistema en salud, seguridad, medio ambiente y Calidad (SSMAC).

Sep 9, 2007

By A. W. Deurbrouck

The Bureau of Mines analyzed 13 samples collected from three Randolph County coalbeds. The Peerless and Sewell bed samples were generally of metallurgical quality as received from the mines or could be easily upgraded. How-ever, the Lower Kittanning coa1bed samples proved to be quite inimical to upgrading to metallurgical quality.

Jan 1, 1966

By Gilbert A. Bonforte, Hugh P. Caspe, Tracy K. Lundin

The Narragansett Bay Commission (NBC) Combined Sewer Overflow Abatement Program is a major effort to address and mitigate discharges from combined sewer overflows in the Providence, Rhode Island area. The proposed system consists of three deep rock tunnel segments totaling 17.8 km (11.1 miles) in length that will provide 860,000 cu m (227 million gal) of storage at depths up to 99m (325 ft). This paper discusses 13.5 km (8.4 miles) of 6.64m (21.8 ft) finished diameter tunnel, four construction shafts, 19 dropshafts and one large diameter pump station shaft tapered from 1 5.2m (50 ft) at the surface to 27.4m (90 ft) at depth. All facilities are in preliminary design.

Jan 1, 1995

Held at San Francisco, Cal., Thursday to Sunday, Sept. 16 to 19, 1915 COMMITTEES Arrangements CHARLES W. MERRILL, Chairman EDWARD H. BENJAMIIN H. C. HOOVER FRED `V. BRADLEY W. C. RALSTON ABBOT A. HANKS G. H. CLEVENGER Excursion and Accommodations ABBOT A. HANKS, Chairman E. T. BLAKE R. H. BEDFORD C. G. DENNIS FREDERICK BRADSHAW C. E. GRUNSKY, JR. EDMUND JUESSEN ARTHUR B. FOOTE F. A. KEITH GEORGE 0. BRADLEY CHARLES JANIN E. N. ENGELHARDT R. S. HASELTINE N. CLEAVELAND

Jan 12, 1915

By Feria Bengoa

El creciente interés del público sobre los problemas ambientales, la satisfacción de los clientes y la seguridad minera, ha generado un alza de leyes en el sector minero e industrial, nuevas ONG y la búsqueda de productos, materiales y procesos compatibles con la preservación de los recursos naturales y cada vez más seguros. En ese sentido, el presente trabajo muestra la estructura del SIG basada en el ciclo conocido de Shewhart (PDCA), y que constituye la espiral de mejora continua de las normas internacionales ISO 9001, ISO 14001 y OHSAS 18001. La base comprende 17 procesos que conforman el SIG según la filosofía del PDCA, los que han sido agrupados como: Política, Planificación, Implementación, Evaluación, Mejora y Revisión de la Alta Dirección. La implementación del SIG que se está realizando en la Fundición de Cobre, asegura la calidad del proceso productivo, estandarizar las mejores prácticas operativas a través de instrucciones de trabajo y procedimientos, motiva y forma a todo el personal de la empresa, cumple con la legislación y mejora la seguridad y salud ocupacional de todo el personal.

Sep 12, 2005

By F. K. McIntosh, L. A. Dahmers

"INTRODUCTION North Carolina has been the leading producer of mica in the United States, accounting for roughly 50 percent of the Nation's output. The producing area is a belt some 100 miles in width lying in the Mountain and Piedmont sections in the western part of the State. Ashe, Watauga, Avery, Mitchell, Yancey, Buncombe, Haywood, Jackson, Macon, Transylvania, Rutherford, Cleveland, and Lincoln Counties supply the bulk of production, while small amounts have been produced in Gaston, Catawba, Burke, Wilkes, Yadkin, Stokes, and Person Counties.To assist the operators and expedite the production of mica during the recent emergency, the Bureau of Mines drilled four of the more promising mica properties in this State. The results of this exploratory program are recorded in this report.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, L. B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and makes beneficiation tests."

Apr 1, 1948

By J. Roth

The increasing demand of the filler industry regarding fineness and better delaminated products led to the development of a series of different grinding machines, which differentiate basically by the grinding mechanism as well as the kind of classification. Spiral jetmills grind, as it is well known preferably by delamination, therefore a spiral jetmill with integrated dynamic classifier has been developed. Especially the enhancement of the functional properties of the used industrial mineral fillers is a factor of highly increasing importance. These properties are very often bound to the platy shape of the minerals expressed by the aspect ratio. The developed Spiral Jetmill shows sufficient ability for such delamination and therefore increases in aspect ratio. In a series of comparative tests the suitability and advantages of this system regarding achievable fineness down to the submicron range as well as the conservation or even improvement of the aspect ratio of different minerals has been studied. As an emphasis on the results application tests with certain materials in the plastics field have been conducted. Due to the fact that in this range the required specific energy for achieving the necessary fineness increases exponentially another target is to optimize the grinding efficiency. A special feed control system provides on one hand a sufficient load inside the mill to obtain maximum utilization of the applied energy and on the other hand to prevent the mill from overfilling and coming with this a poor classification. The integrated classifier is a combination of a high speed motor with directly attached classifier wheels. This unit on one hand grants the necessary high circumferential speed of up to 190 m/s for providing an exact top cut of the ultrafine products and on the other hand gives the required operational reliability for continuous operation. Hard grindable impurities, which enrich inside the mill chamber, can be rejected from the process leading to an even cleaner product. Comparative tests on a talc product with certain free quartz impurities showed a significant improvement of the final product with respectively low loss on rejected material. This effect again had a beneficiary impact on the suitability of the final product when used in plastics application.

Jan 1, 2014

By R. Gensemer

A number of state and federal agencies are calling for development of aquatic life criteria for conductivity. These aquatic life criteria or ?benchmarks? are based on observed correlations between conductivity and benthic macroinvertebrate community composition, generally measured by composite metrics or indices. However, development of an aquatic life criterion for a composite variable like conductivity is made difficult by a number of factors. Based on a database from West Virginia, observed patterns of invertebrate community composition versus conductivity may instead be related to a combination of abiotic (e.g., ionic composition, habitat) and biotic (e.g., life history, colonization potential) factors. Many benthic invertebrate taxa also do not respond to increasing conductivity in a consistent relationship. Many states have determined that a composite variable, like conductivity or TDS, is not appropriate for criteria development, as many studies have shown that toxicity varies as a function of ion composition and can be mitigated by elevated hardness. We conclude that the relationships between conductivity and changes in benthic macroinvertebrate community composition are neither strong nor reliable enough to warrant derivation of a criterion based solely on conductivity.

Jan 1, 2011

By Erie C. Donaldson

Gas-displacement tests were made in Berea Sandstone and Arbuckle Lime-stone cores to determine the relative permeabilities to gas, oil, and water for two-and three-phase dynamic systems. Three-phase relative permeabilities were obtained by displacing oil and water from the core with gas and measuring the flow rates of the three fluids simultaneously. It was found that relative permeabilities to fluids in a porous medium are affected by the saturation distributions of other fluids in the medium as well as by their own saturation distributions.

Jan 1, 1966

By Andy Fortin, Jeet Basi, Simon Hille

Goldcorp’s Eleonore mine is situated in Ell Lake area in the northeastern part of the Opinaca reservoir in the James Bay region of Quebec. The design of the 7000 t/d process plant includes crushing, grinding, bulk sulphide flotation, separate concentrate and tails leaching and detoxification circuits and residue handling. Detoxified flotation tails are thickened and filtered. A portion of the filtered tails are blended with the thickened detoxified sulphide concentration for paste backfill. The remaining filtered tails are trucked to the waste management facility. This presentation will describe the challenges faced with the commissioning and subsequent ramp-up of the flotation tails filter plant and the successes achieved by the multi-discipline team at Eleonore.

Jan 1, 2016

By C. M. Diaz, S. W. Marcuson

In the late 19th century, the discovery of rich nickel-copper sulfide ore bodies in Sudbury and the need for tonnage quantities of the metal to be used in nickel steel armor provided the foundation for establishing the Canadian nickel industry. For almost 50 years, International Nickel was the key player. In 1930, Falconbridge Nickel entered the field. These two companies remain the key Canadian nickel producers. This paper discusses the factors that have influenced the evolution of nickel smelting processes. The initial Sudbury ore smelting and nickel copper separation technologies were imported from abroad. It was only in 1937 that International Nickel established a process research laboratory in Copper Cliff The explosive post WW II industrial development created a strong demand for a broader variety of nickel products. For both International Nickel and Falconbridge, R&D became an essential business tool to succeed in the new market scenery. In the last few decades, new technologies were developed and commercialized to respond to the raising cost of energy, society pressing environmental concerns, the advent of nickel laterites as an important source of new metal, the incorporation of new nickel producers to the market, and, therefore, the need to increase productivity. Canada thus became an important exporter of technology. In this paper, the authors review this history with the objective of highlighting the forces that have triggered the most important changes in Canadian nickel smelting.

Jan 1, 2005

By P. Pal Roy, R. B. Singh

"This paper focuses on a number of interesting results to establish the theory and principle of air-deck blasting. It also gives the mechanism of breakage that takes place in air-deck blasting under varying charge load conditions. With these aspects in mind, the mine management can implement this up-coming technology to enhance safety and higher productivity. IntroductionThe method of air-decking has become an increasingly popular technique in production and presplit blasting. In the blasthole, an explosive column is combined with an airchamber. The main aim of the technique is to control breakage through effective distribution of explosive energy and thereby enhance uniform rock fragmentation. An air column lowers the initial pressure of the explosive products and simultaneously increases the time of interaction for the detonation front with the surrounding rock, which enhances rock breakage.To study air-deck blasting, CMRI initially conducted experiments using indigenously developed, low-cost wooden spacers of different sizes and strengths. Air-deck blasting was first tried using these spacers in 1993 at Jambad OCP, ECL and Chasnalla OCP, IISCO. The experiments were extended in 1994 at Bermo Mine, DVC. The results were subsequently published by Pal Roy et al., in 1995. It is worth mentioning that the performance of air-deck blasting during this period was only compared with conventional blasting practices without going into detail of the theory behind the process."

Jan 1, 2001