Search Documents

By J. A. Cole

The mill project at Lone Tree was commissioned in October, 1993, followed by the commissioning of the autoclave pressure oxidation circuit in February, 1994. Discussion of the first year of milling operations at Lone Tree is presented. The mill is currently operating above the design rate of 2,267 mt/d (2,500 st/d). Both phases of the start-up were essentially trouble free. The few problems that were encountered and the respective solutions are addressed.

Jan 1, 1995

By Fred S. Karn

Inhibitors are used in coal mines as a precaution against accidental dust explosions. Although rock dust is the usual inhibitor many others have been tested. To facilitate testing a screening process using laser irradiation was proposed. The procedure includes irradiation of a coal-dust mixture followed by mass-spectrometric analysis of the evolved gases and an evaluation of the flammability characteristics of the gases. Carbonate-type inhibitors decreased the percentage of combustibles in the gases generated and inhibitors like NaCI (thermally stable salts) decreased the total gas generated. A suitable test procedure did not result from the investigation, demonstrating the inadequacy of fast heating, non-combustive techniques in rating inhibitors of coal dust explosions.

Jan 1, 1973

By Thomas M. Barczak

Wood cribs are used extensively to stabilize openings in underground coal mines. This U.S. Bureau of Mines report describes the results of full-scale testing of several multitimbered wood crib configurations. Multitimbered configurations are wood cribs that are constructed with two or more timbers per layer. Nine different crib configurations were evaluated. Configuration parameters under study included the aspect ratio (height-to-width relationship) and the percentage of solid rr:aterial used in crib construction. Test results and generalized wood crib behavior are discussed and recommendations are made concerning crib constructions to maximize strength and stability. Crib performance is enhanced by reducing buckling effects by decreasing the aspect ratio and geometry considerations that increase the moment of inertia. A cost benefit analysis of multitimbered wood crib configurations is made. Generally, increasing the percentage of solid provides more resistance at less unit construction cost. A comparison of laboratory results and underground observations of several wood pack wall supports suggest in situ load capacity is less than that measured in laboratory testing. Reasons for the apparent decrease of in situ load-bearing capability include load rate effects, stiffness of reaction surfaces, and varying boundary conditions that alter the load transfer mechanics of the crib structure.

Jan 1, 1991

By R Durchholz, A-J Heiertz, R Schmitz

Mining of lignite is the largest bulk materials handling activity in Europe. In order to mine this lignite, with an average calorific value of only a third of bituminous coal in an economical way, highly efficient opencast mining technology is mandatory. The total continuous mining of overburden and lignite was introduced more than 60 years ago and was subsequently developed stepwise into the largest mass transport system of the world. In 2011, the Inden Mine, one of three RWE Power mines, stripped 90 Mbcm of overburden to produce 22 Mt of lignite. In total, nearly 100 Mt of Lignite was produced from the three mines of RWE Power in Germany. Beside bucket wheel excavators (BWE), several high-performance in-pit crushing and conveying (IPCC) systems, which allow the adoption of continuous mining systems, even for typical shovel and truck (S&T) operations, are available today. RWE Power assists operators considering a change from the S&T to IPCC technology, both in the planning process involving large-scale belt conveyor systems and later with operational know how transfer. In a number of cases, the challenges associated with this system change have been addressed and solved successfully. One key challenge is managing the development of skills for operating the belt conveyor systems efficiently. This paper compares the effectiveness of S&T to different configurations of continuous mining operation for an up to 170 m deep mine with a total annual output of 117 Mbcm. From the mine operatorÆs point-of-view, the quantity and skill level of staffing required for operation and maintenance are discussed in detail. The main conclusion of this paper is the larger the operation becomes and the longer the mine life is, the earlier fully continuous mining systems should be planned and implemented.CITATION:Schmitz, R, Durchholz, R and Heiertz, A-J, 2012. Change challenges for large open pit mines, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 103-110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By Harry R. Nicholls

Six different chemical explosives were detonated in a test series to com-pare their relative performance in granite. From 5 to 255 feet from the detonation point, strain, acceleration, and particle velocity were recorded and analyzed for amplitude and pulse shape. Strain energy was calculated from strain data, and displacement data were obtained from particle velocity data by integration. The results show that explosives which have a characteristic impedance more closely matching that of the rock generate larger peak amplitudes than explosives with a lower characteristic impedance. The results also show that as the ratio of characteristic impedance of exp1osive-to-rock approaches unity, more rock is crushed and a larger percentage of the avail-able explosive energy is transferred to the rock as seismic energy. The effect of characteristic impedance is shown to be greater than the effect predicted from acoustic theory and is believed to be indicative of shock wave effects at the explosive-rock boundary.

Jan 1, 1965

By Rajiv Kalra

This paper reviews the following aspects of the world?s largest manufactured Grinding Mill?s in terms of diameter and power, along with the world?s biggest shop assembly and trial run of the mills delivered to Sino Iron Magnetite Project in Australia. 1. An overview of the basic flow sheet of the Sino Iron (Magnetite) Project located in Australia 2. An overview of in-house designed CITIC Heavy Industries 12.2 m (40ft) F x 11 m(36ft) LG ? 28MW AG mills including FEA and major components 3. In-house manufacturing at CITIC-HIC work in Luoyang China of all major components for 6 off Ø12.2 m(40ft) AG mills and 6 off Ø7.9 m(26ft) x 13.6 m(44.6ft) LG-2 x 7.8 MW Ball Mills 4. Major aspects of design and preparation of the biggest shop trial run of Ø7.9 m(26ft) x 13.6 m(44.6ft) LG Ball Mill witnessed by international EPCM?s and clients in July 2009. 5. Major aspects of one piece assembly of 1300 tonne rotating element of the Ø12.2 m(40ft) x 11 m(36ft) LG AG Mill and Ø7.9 m F (26) x 13.6 m(44.6ft) LG Ball Mill at the port of the export China and transport to Australian Port and then to site. 6. An insight to unique installation methods used for Ø12.2 m(40ft) and Ø7.9 m(26ft) rotating element lifting on the mill foundation in one piece assemblies. 7. CITIC Heavy Industries present capability for in house design and manufacture of Grinding Mills up to Ø13.7 m (45 ft) with 35 MW Gearless drives and Ø12.2 m(40ft) with 2 x 10 MW Geared Mill drives

Jan 1, 2012

By F. T. Cawood

One of the consequences of globalizing mine finance is a necessity to apply uniform accountancy and valuation standards that are clearly understood and consistently applied by the global investment community. However, each country has unique circumstances, which sometimes make it difficult to align domestic practice with international requirements. South Africa is no exception and issues such as its political history, a taxation regime enforcing different rules on different mineral producers and a unique mineral rights ownership distribution, are barriers to internationalization. The economy is in a transitional phase as a result of the many and diverse policy documents following the change in political dispensation in 1994. Many of these documents have recently been implemented through new legislation and, in the case of mining, negotiations are continuing in order to ensure an acceptable outcome. This paper discusses the challenges that the South African minerals industry faces in the field of mineral property valuation. It draws on international experience and includes a discussion on the unique considerations that the South African mineral property market must take into account in establishing a code for this purpose, as such a code could later be aligned with international practice.

Jan 1, 2004

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes are diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favors a different flotation environment. An improvement in the kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferential recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rpm, rotor size/type) at the beginning of the row, where flotation is typically froth phase limited and operational, and set-up parameters have a limited influence on the recovery. ? Higher-powered flotation machines (high rpm, high power rotor size/type) at the end of the row to improve fine particle recovery. ? Lower-powered flotation machines (low rpm, low power rotor size/type) to enhance coarse particle recovery. In evaluating the effect of turbulent kinetic energy on flotation performance, the spatial distribution and its effect on size denominated recovery needs to be evaluated. The mean energy dissipation rate is a measure of the bulk energy input, but CFD-based models offer a more introspective view of flotation sub-processes. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced air and naturally aspirated machines. Keywords: CFD-based model, attachment, detachment, energy dissipation, hybrid energy flotation?, forced air, naturally aspirated

Sep 1, 2012

By V

"Recent regulations, as well as a general aversion to central dust collectors within the Powder River Basin Coal user’s community, have created a need for an alternate method for eliminating airborne dust. This paper addresses the capital expenditure as well as the cost of ownership of an integrated point source air cleaning system in comparison to a central collection system. This assessment was conducted by comparing the cost to purchase and operate a central dust collection system and integrated air cleaner system on a typical multiple transfer point application. The central dust collector consists of a negative pressure blower, a series of filter bags, a collection hopper, a screw conveyor to place collected material back into the material stream, and a series of ducts to pull air and dust from individual pickup points. The point specific integrated air cleaners consists of a negative pressure blower to pull dust and air from an application point through a bag-less filter media located at the application point. The agglomerated material is then redeposited into the material stream at point of use without the need for ducting or a central material hopper. The assessment yielded a 54% reduction in capital expenditure and a 26% reduction in operating costs for the same application when using individual dust filters as opposed to a central system. In addition to the lowered cost, there are reductions in risk associated with the elimination of ductwork and the central containment enclosure for collected explosive dust. By the conclusion of this paper, the reader will have a better understanding of the quantifiable differences between a central dust collection system and a set integrated air cleaner systems. BACKGROUND Spillage has always been a problem in the bulk solids handling industry. As long as there have been conveyors, there has been spillage. Spillage is material that falls off a conveyor belt and creates a hazard in the environment around a conveyor belt."

Jan 1, 2016

By T. W. Johnson

The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past-several years the flow of natural bas through high--pressure pipe lines.4 This report deals with that part of the study involving the design of pipe-line, systems consisting of lines laid parallel to each other. The lines are deferred to as the original line and the parallel line. The paralleling line may or may not extend the entire length of the original line; however, the parallel line is, connected at its two ends to the original line. As a result of the large expansion of the natural-gas industry almost all markets within economic distance from the developed gas fields have at least one pipe line supplying them with natural gas. Small increases in the consumers' demand for natural gas can be met usually by increasing operating pressures, but any marked increase in demand necessitates paralleling sections of the existing systems. It is believed that to a large extent future

Jan 1, 1934

By Michael Cooper, Eric Konigsmann, A. Moerman

"A paste backfill plant and underground piping distribution system was commissioned at the Brunswick Mine in June, 1998. Concentrator tailings, composed mainly of pyrite and lesser amounts of silicate minerals with a P80 of 37um (45 YO-20 pm), are pumped to the backfill plant. The backfill plant uses conventional thickening and disc filtering to dewater the solids, which are then mixed with binder in twin screw mixers. The paste is discharged through a gob hopper and one of three boreholes by gravity. Approximately 65% of the concentrator tailings will be placed underground at full production. The remaining thickened tailings will be pumped to an existing impoundment area. Application of paste technology will completely replace the use of cemented rock fill in the mine by the end of 1998.The design capacity of the paste backfill plant is a total of 360 dmtph of cemented paste through two parallel production lines. The plant is highly instrumented and controlled via a hybrid Programmable Logic Controller (PLC-5) and Fisher ProVox Distributed Control System that is in communication with the property information highway. Video and audio signals from the underground system are carried to the surface plant via a leaky feeder communications/fiber optic system.The underground distribution system consists of a network of 200mm diameter boreholes and piping. There are approximately 3.5km of boreholes and 5.5km of piping in the system. To minimize pressures, the greatest piping length from any borehole is approximately 400m with all piping being open-ended. There are no valves in the entire paste distribution system.Construction of the plant, including installation of piping to and from the plant and preparation of the underground distribution system, was completed in less than one year from the time of management approval for the $M 22.3 project."

Jan 1, 1999

By T. Khumalo, L. P. Coetzer

This paper addresses the impact of the variable speed drive on the particle size distribution in the product of a fully autogenous UG2 grinding circuit. It further discusses the impact of a varying particle size distribution in the product of the mill on the downstream classification and milling circuits. An industrial case study was used and data is presented to illustrate the techniques applied to identify the root cause of the shift in operational efficiency. The results achieved from both the investigation into the shift in plant efficiency and the sub-sequent corrective action taken illustrate that the root-cause methodology used in advance control can be effectively applied on production sites to both detect the shift and identify probable root-causes. The industrial example used confirms that the variable speed drive in a UG2 autogenous milling operation is a critical control parameter to ensure that the plant operates to design specifications.

Jan 1, 2006

By Fábio de Oliveira Braga

Atualmente, tecidos de fibras sintéticas como a aramida (Kevlar®) e o polietileno (Dyneema®) têm sido os preferidos para proteção balística contra munições leves, e para integrar sistemas de proteção contra calibres superiores, como o 7,62 mm. Porém, por apelos econômicos, ambientais e da disponibilidade limitada destes produtos, materiais alternativos têm sido testados. Neste cenário, destacam-se os compósitos reforçados com fibras naturais, que têm demonstrado bom desempenho balístico. Assim, o objetivo deste trabalho é avaliar o desempenho individual de compósitos reforçados com fibras naturais de curauá, quando submetidos ao impacto balístico com munição 7,62 mm. Foram executados ensaios balísticos, medindo-se a energia do projétil absorvida pelos materais, e os resultados tratados estatisticamente por Anova e teste de Tukey. Mostrou-se que estes compósitos têm potencial para substituir as fibras sintéticas em sistemas de blindagem para proteção pessoal, com a vantagem de serem materiais leves, de baixo custo, nacionais, de ampla disponibilidade e ambientalmente corretos.

Aug 17, 2017

By T. Stauffer, B. McGunegle, A. Adu-Acheampong

The Fairmount Minerals, Inc., Maiden Rock underground sand mine historically delivered air to ventilate diesel-powered equipment at its working faces through high-resistance, 15-inch-diameter PVC distribution lines. In support of plans for expanded production, three new, low-resistance ventilation design alternatives were analyzed. The study determined that adequate ventilation for expanded production was possible with various commercially-available, high-volume/low-pressure fans combined with a systematic layout of control structures. The recommended re-design was implemented in 2001, resulting in a significant increase in flow volumes and a noticeable improvement in the mine environment.

Jan 1, 2007

By E. J. KENNEDY

FEBRUARY 15-18 will be the outstanding dates of the month for members of the A. I. M. E., for then the 141st Meeting of the Institute is to be held in the Engineering Societies Building, at New York. What with 41 technical sessions, the Annual Business Meeting at 4 o'clock Tuesday afternoon,, two sessions of the Section and Division delegates, minor committee meetings, and the many luncheons and dinners, the Dinner-Smoker, Informal Dance, President's Reception and the Dinner-Dance, the opportunity will be limited to do- more-than cast sheep's eyes at New York's other multitudinous attrac¬tions until the meeting is over. The technical program is diverse but well organized. The sessions are almost equally divided among the four days, with ten on Monday, Tuesday, and Wednesday, and 11 on Thursday. The meeting opens Monday morning with registration. Be sure to attend to this detail. Failure to do so may have its repercussions at the meeting and throughout the year.

Jan 1, 1932

Development of Grindability Tests Based on Direct Measurement of Energy Nowadays, for the characterisation of the grindability different grindability indices - Bond-work index (Wi), Hardgrove Grindability Index (HGI) or Zeisel specific grindability (Wt) - are used. Generally, the grindability tests are carried out under relatively simplified circumstances, in a special dry batch mill with defined feed size material until prescribed conditions are reached at room temperature. However, in the fine- and ultra fine grinding, which is a frequent task (fly ash, tailings, alumina, etc), a fine material (<50 - 200 ¦m) is usually ground down to the few micrometers. The conventional grindability testing methods and apparatuses (Bond-, Hardgrove-, Zeisel-processes) for their determination, although, are not suitable directly to measure the grindability of such fine materials, since the maximal particle size of the feed material (0.5 - 3 mm) to be tested is much higher. One of the important goals of the research carried out in our Institute was to develop the novel grindability testing methods, which are suitable for the fine and ultra fine grinding, and additionally provide the possibility for the fast determination of the grindability. In order to realise the above aim the conventional Bond- and Hardgrove- mills were modified in order to directly measure the grinding work. In particular, the Hardgrove-mill was equipped with a simple torque-meter (load cell). The Bond-mill was rigged with a digital electric power measurer. The systematic experiments were carried out parallel in both mills using the conventional and the developed methods. Finally the results of both were compared. The measuring results have proved that the Bond-work index can be determined based on the developed methods. The new grindability testing methods were applied successfully in several industrial research tasks for the determination of the specific grinding energy and the Bond-work index. These methods can be also used in the industrial practice for the control of the grinding process.

Sep 13, 2010

By H. C. Miller

The success of any project in which gas is injected into oil-producing sands to increase the current rate or the economic ultimate production of oil or in which surplus gas from oil producing operations is stored temporarily in reservoir sands that have been wholly or partly depleted of their producible oil depends mainly upon an understanding of the underground movements of oil, water, and injected gas and the ability to control their speed and direction of migration through the reservoir sands. Many operators believe that injected gas always travels up the structure and drives oil to wells structurally higher than the injection wells, because the specific gravity of the injected gas is less than that of the fluid substances in the formation. Consequently, many injection wells are located on the flanks of oil-bearing structures with the idea of utilizing the energy of the injected gas to drive the oil to producing wells higher on the structure. It is true, under certain conditions of pressure and fluid depletion of the reservoir sands, that injected gas will move in an up-structure direction, but the theory that injected gas always moves up the structure is based on an erroneous conception of the laws that pertain to the expansion of gases. By definition, "a gas is distinguished by its property of infinite expansion and is limited in volume only by the walls of the vessel which contains it."3 The expansion of gas that is injected into reservoir sands also is limited by "walls" that surround the space influenced by the injected gas. The walls of the majority of undrilled or virgin oil-bearing reservoirs in California are the impervious shales overlying and underlying the productive strata and the "dams" or effective barriers of edge water around the rims of the reservoirs. When gas is injected into the sands of a producing reservoir, regardless of the location of the injection well on the structure or the degree of depletion of oil from the sands, one of the walls which confine the gas in the structure about the injection well is fluid. This wall will be edge water in a nearly depleted reservoir, where the drainage cones or regions of reduced pressure about injection and producing wells intersect; and, where there is no interference of drainage cones and the injection well is structurally above the edge water, the wall will be oil. In some producing reservoirs bottom water may be the lower wall of the space that confines the gas about injection wells, but the effect of bottom water on limiting the expansion of gas is the same as if the water was not present and impervious formation separated the producing from the underlying nonproducing strata. Therefore, since compressed gas always seeks regions of reduced pressure and its final volume is limited only by formation and fluid barriers and since the force exerted by the gas under pressure is equal in all directions, the course of migration of injected gas in reservoir sands in California and the

Jan 1, 1932

By R. V. Ramani

This volume is the second of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume I: Ore Reserve Estimation, Volume III: Mine Coordinate Generator System, and Volume IV: User's Manual for OPMHS/2. The dragline model described in this report simulates the movement of the dragline bucket across the digging face, the swing load, the dump, and swing back. It is programmed to handle chopdown, key cut, main cut, and rehandling operations. Provisions have been made for simulating equipment and mining delays. Any mining method can be specified in terms of numbered blocks, the dragline positions for the mining block and the dumping location for the block. Accounting procedures permit the calculation of production rates, rehandle volume, dig and delay times. The model can be used to study the effects of varying mining conditions, cut width, and spoiling sequence with special reference to toxic spoil, overburden and bench removal procedures. The basic input data for the model include machine parameters, the geology and material characteristics, the mining parameter, and the delay characteristics of the equipment.

Jan 1, 1985

By Brenda Myers-Bohlke, Tor L. Brekke

INTRODUCTION In recent years several cities in the Eastern United States have constructed subway systems in deeply weathered igneous and metamorphic rocks. Portions of these transit tunnels and shafts have penetrated zones of saprolite. The purpose of this paper is to define saprolite and discuss saprolite behavior in terms of construction and design of tunnels and shafts. Saprolites are products of in situ weathering of rock, with properties intermediate between those of soil and rock. A well-developed weathering profile can be divided into zones of residual soil, saprolite, transition zone materials, weathered rock, and fresh rock. Saprolites are distinguished by a high degree of weathering and by retention of parent rock textures and discontinuities. These structures persist as relict features because of iso-volumetric weathering (Cleaves, 1974) and formation of intergranular bonds that give cohesion to the saprolitic material. As saprolite continues to weather, the bonds are broken, causing the saprolite to decompose and disintegrate into a true residual soil mass without relict structure. Saprolites may form from igneous, metamorphic or sedimentary rocks, but are most easily recognized when derived from igneous and metamorphic rocks because of their inherent structures. The physical characteristics and properties of residual material vary as a function of mineralogic composition, structure, and discontinuities of its parent rock.

Jan 1, 1985

By Ralph B. S

Bacterial leaching of low grade quartz felspar porphyry copper ore was studied in large-scale laboratory percolation leaching columns.Limitations in the release of soluble copper showed up before fifty per cent recovery, due to occluding precipitates of iron oxides and hydroxides. Precipitates were removed by increasing the acidity of irrigation feed four-fold with respect to sulphuric acid. However, irrigation at low pH (pH 1.5) inhibited copper leaching. Resumption of bacterial leaching at pH2 was achieved by introducing a period of non-irrigation. The results suggest a 'direct' attack by bacteria on the chalcopyrite substrate rather than an 'indirect' ferric-leach mechanism.

Jan 1, 1981