Search Documents

Site specific geotechnical data, deposit characteristics and method of mining are key factors when assessing an appropriate slope design philosophy. Mining geotechnics should be viewed as an iterative design process linked closely with mine planning, development and operational safety constraints. This case study presents geotechnical investigations for slope design at Macraes Flat Gold Mine using kinematic, probabilistic and economic analyses tempered with knowledge of site specific conditions. The recommended designs not only reduce early waste stripping tonnages but also provide data to optimise final walls.

Jan 1, 1992

By H. R. Appell

The Bureau of Mines is experimentally converting cellulose, the chief constituent of organic solid waste, to a low-sulfur oil, All types of cellulosic wastes, including urban refuse, agricultural wastes, sewage sludge, wood, lignin, and bovine manure, have been converted to oil by reaction with carbon monoxide and water at temperatures of 350° to 400° C and pressures near 4,000 psig, and in the presence of various catalysts and solvents, Cellulose conversions of 90 percent and better (corresponding to oil yields of 40 to 50 percent) have been obtained. A continuous reactor for use at maximum conditions up to 500° C and 5,000 psig has been operated successfully, Using sucrose as a feedstock, operation in this system has permitted a simplified and preliminary chemical study of the conversion process. Oil yields of over 30 percent have been obtained with this unit.

Jan 1, 1971

By M. P. Brungs, S. Haji Amini

Static dissolution of CaO into a CaO-SiO2-Al2O3slag and slags with additional fluxing agents (fluorspar, nepheline syenite and ilmenite) was studied. The slag was packed into dense CaO crucibles and heated to 1500ºC /1600ºC. After reaction, the crucible was air cooled and cross-sectioned. The development of the Ca2SiO4 phase and concentration profiles of various cations across the reaction zone were examined by Electron Probe Micro Analysis. At 1500ºC, a Ca2SiO4layer was found to form at the CaO/slag interface. No such layer was evident at 1600ºC. Ilmenite and nepheline syenite were found to be effective substitutes for fluorspar, increasing the rate of CaO dissolution.

Jan 1, 2004

By R. Rampersadh

Paper written on project work carried out in partial fulfilment of B Eng (Metallurgical Engineering) degree Steel was sampled after calcium treatment, to follow changes in inclusion composition during the processing of alumium-killed steel into continuously-cast billets, at Mittal Vereeniging. There is some shift in the distribution of inclusion compositions towards alumina, as the liquid steel moves from the ladle to the tundish. This shift may reflect some reoxidation. However, the effect on inclusion modification is small, since only a small fraction of the tundish oxide inclusions is fully solid?which agrees with the plant observation that these heats cast without clogging. Magnesium oxide in the inclusions contributes to liquid formation, substantially increasing the range of lime: alumina ratios over which the inclusions are partially or fully liquid.

Jan 1, 2006

By D. Y. Wang, G. Y. Sha, X. L. Shen, D. R. Gu

The study of the volatilization kinetics of zinc and lead in pellets made of zinc-leadbearing dust mixed with coal powder, in a nitrogen atmosphere and at a temperature range between 1100 °C and 1300 °C, shows that the reduction temperature has a significant effect on the volatilization rates of zinc and lead, and that both the particle size of the coal powder and the extra carbon content has no effect on the volatilization rates. The obtained activation energies for the volatilization of zinc and lead are 79.42kJ/mol and 88.74kJ/mol respectively. The volatilization rate of zinc is controlled by the reaction between the zinc oxide and carbon monoxide while that of lead is controlled by the lead evaporation reaction, and the diffusion of gaseous lead through the gas boundary layer covering the surface of the reduced liquid lead.

Jan 1, 2000

By G. S. Littlejohn

In anticipation of the flooding of an adjacent dolomitic groundwater compartment, five rough parallel sided boundary plugs at 58 and 50levels have been designed to resist safely hydrostatic heads of 1500and 1250 metres, respectively, over a service life of 100 years. Following a description of the engineering properties of the surrounding rocks, the paper details the design considerations relating to structural length and strength, hydraulic gradient, rock mass watertightness, constituent materials of mortar intruded concrete, pregrouting of permeable discontinuities within the surrounding rock mass, a bentonite barrier to resist aggressive mine water, plug tightening and design performance requirements. Routine quality control tests include permeability of the rock mass, fluidity, bleed and strength development of the intruded mortar, and temperature of the intruded concrete during curing. A special test programme includes determination of strength and stiffness of cored concrete and rock samples, shear strength of the rock/plug interface and associated in situ contact stress in order toe stimate the load safety factor against plug failure by shear.

Jan 1, 2006

By Conny Postupack

To make money in mining coal you have to sell it for a lot more than it cost you to get it out of the ground. And yet, every year it cost us more and more to stay inbusiness, while the price we get for coal does not increase at the same rate.

Jan 1, 1990

By M. Zaske, E. R. Mortensen

"As mine operators continuously look for ways to improve functionality and increase the capacity of their facilities, existing process equipment is often pushed to and past its designed limitations. As a result, equipment manufacturers are asked for economical solutions to meet redefined processing needs. Newmont Mining in Nevada was faced with such a need in its carbon-in-leach (CIL) train. In a collaborative effort between Newmont and Derrick Corp., tests were conceived to assess the viability of drop-in replacement screens using a three-dimensional screen panel. The synthetic pyramid screen panel was designed to increase flux while maintaining the existing equipment footprint. The test is the end result of an ongoing research and development project that Derrick undertook in an effort to refine and upgrade its urethane screening media. The application of this new screening media is presented for this CIL application along with future plans to implement the technology in trash, safety, carbon dewatering, carbon sizing and other scalping applications.In spring 2014, Process Machinery Associates (PMA), Derrick’s local area representative, met with Newmont to discuss the operation of the in tank screens in the CIL train at Twin Creeks, near Golconda, NV. The process was originally designed for about 12+ kt/d (13,000+ stpd) but the throughput has been steadily rising since the plant was commissioned. Newmont now requires 14.5 kt/d (16,000 stpd) to be processed. The original screens were running at their maximum capacity, and Newmont required additional screening capacity to continue the upward trend in production.Physical separation by use of screening is one of mineral processing’s oldest methods. Screening media can be prone to blinding and pegging, and the necessary support structures required for finer apertures result in smaller open areas. Therefore, more screening area generally requires larger panels and, thus, larger machines, screening media that does not blind or a combination of both.In an effort to avoid larger machines, Derrick had been working on a revolutionary threedimensional panel that would add nonblinding screen area in the same footprint of an existing machine. Alpha testing of the new screen panels began at Newmont Mill 2/5 in July of 2013. It was still occurring when PMA approached Twin Creeks about beta testing a refined machine and pyramid panel. After presenting the initial results, Twin Creeks determined that an upgraded machine and pyramid panels would be a possible solution to meet production needs. The testing of a machine eliminated the risk of capital costs to Newmont and provided Derrick the opportunity to obtain additional data."

Jan 1, 2015

By Henrique Silva Furtado

Concerning production of low phosphorus steel critical grades at ArcelorMittal Tubarão site, bottom blowing system plays a very important role. For those systems with independently controlled tuyeres, some non-uniform bottom blowing patterns seem to be promising in improving metal-slag mixing; however, based on computational fluid dynamics (CFD) results of ArcelorMittal Tubarão’s post oxygen bottom blowing, this may not be generalized. Also, from industrial trials it became clear that higher the bottom blowing flow rate, the closer were the end point P to the equilibrium. Despite this result an analysis of the apparent mass transfer coefficient has shown a week correlation with the classical power stir correlation suggesting a more complex kinetic limiting step for phosphorus removal.

Jul 30, 2018

AQUILA Mining Systems Ltd., designs, develops and delivers systems for measurement, analysis, simulation, control and automation to the mining, construction and petroleum industries. The objective of current efforts by AQUILA is the continued development and refinement of computerbased systems and techniques to automatically process monitored performance data from surface blasthole drills and mining shovels, and the management and coordination of these pieces of equipment by GPS (Global Positioning Systems).

Jan 1, 1994

By John J. Henn

Ten proposed processes for the recovery of manganese from domestic resources as a high-grade oxide product are described. Nine of the processes employ sulfur dioxide, sulfuric acid, or a combination of both for leaching. The tenth process utilizes sulfur dioxide to sulfatize the ore at 600° to 850°C before water leaching. In addiction to these ten complete processes, six processes from the patent literature are described. Methods for receovering MnSO4?H2O are also reviewed.

Jan 1, 1968

By Y. C. Liu, G. A. Alers

The anisotropy of Young's modules has been measured in a series of Cu-Zn alloys containing from 1 to 28 wt pct Zn and cold-rolled to 97.5 pct reduction in thickness. These modulus data show a transition in texture as a function of zinc content. In alloys containing 3 pct Zn or less, the texture is essentially that of copper. A transition is clearly seen to develop in 5 and 8 pct Zn alloys, and to have been completed in a 12 pct Zn alloy. Increasing the proportion of zinc to 28 pct does not produce any further changes in texture. The ease and clarity with which this texture transition can be seen in the modulus data is in great contrast with the inccertainty in the visual detertiination of the range of texture transition from a series of pole figures. It is also shown that the rolling texture of the high zinc content alloys cannot be a one-COIIIponenl texture, characterized by the (110)(112) ideal orientations, as usually assumed. A second, quite important component must also be present. Furthermore, the present data are inconsistent with matrix orientations on which the "oriented growth" hypothesis of the Formation of recrystallization textures is based. THE rolling textures of binary fcc alloy systems have generally been considered to lie between two terminal textures. One of these terminal textures is the copper type and the other is the 70:30 brass type. Alloys of intermediate solute content exhibit a texture which is said to be a transition between the two terminal textures. On the basis of efforts to correlate rolling and recrystallization textures, two concepts have been advanced in the literature on the nature of these transition textures. One school1 suggests that the addition of alloying elements, e.g., zinc, causes a gradual rotation about one of the (111) poles from the (358)( 523) ideal orientation of the copper-type rolling texture to the terminal {1 10)( 112) ideal orientation used to describe the rolling texture of 70:30 brass. This concept is depicted in Fig. 1 with the angle of rotation corresponding approximately to the zinc content and is designated here as the "rotational concept", since the ideal orientation of the transition textures varies continuously with alloy content. The other concept,' the "mixture concept", suggests that the copper-type rolling texture is a two-component texture. {358) (523) and {110)(112). The addition of alloying elements affects only quantitatively the relative amounts of these two components—a decrease in the amount of material in the {385}(523) orientation and an increase of that in the {110)(112) orientation with increasing solute content. An experimental distinction between these two concepts is essential to a better understanding of both the mechanism of formation of rolling textures and the subsequent formation of recrystailization textures in fcc metals. Because of the lack of resolution inherent in pole figures, it has not been possible to differentiate between the two concepts on the basis of this data. Both concepts, in fact, make use of the same set of pole figures but interpret them in a manner acco-rding to the view held.'" Experimental results obtained from inverse pole figures or selected-area electron diffraction3j4 simply -yield more refined pole figures but do not eliminate the ambiguity of interpretation. Quantitative measurement of an entirely different, orientation-dependent property must thus be considered

Jan 1, 1967

By P. C. Benedict, J. A. Titcomb

"The following description of the geology of the Northern Empire mine is recorded by the senior author, but is based on the observations and complementary mapping of both authors.The Northern Empire mine is a mile east of Beardmore, and 100 miles northeast of Port Arthur, Thunder Bay district, Ontario.Production started in March, 1934, and terminated in September, 1941. The total number of tons milled was 425,866, from which 153,103 oz. gold was recovered. The lowest level from which ore was mined was the 1,900- foot, but considerable drifting was performed on the 2,075-foot and 800 feet on the 2,415-foot, the deepest level,The vein strikes about N.72°E. and has an average dip of80°S. In stoped sections the quartz averaged about 2 feet wide. On the 1,725-foot level it was drifted on continuously for more than 7,000 feet. In the mine as a whole, practically no commercial ore was found beyond points 1,400 feet west and 1,800 feet east of the shaft. Conspicuous wall-rock alteration extended throughout this section, but not much beyond these limits. There was some splitting of the vein and widening of the alteration halo on the lower levels. The average general colour of the quartz changes with depth .The vein is in 'Keewatin' lava flows, to which it is almost conformable. It lies only a short distance south from the 'Timiskaming-Keewatin' contact ( Fig. 2). This contact is marked by a black graphitic fault. So far as is known the fault is parallel, or nearly parallel, with the flows in strike, but dips at 72°S., which is 5° flatter than the average dip of the overturned flows. A post-vein, almost flat sheet of diabase about 550 feet thick cuts outthe vein from about the 650- to the 1,200-foot level ( Figs . 1 and 3). If it was intruded along a fault, the fault had only minor displacement. A strong alteration halo extends to 200 feet above and below the diabase. The vein was conspicuous but in large part it was below ore grade for 100 feet or more above and below the diabase.-"

Jan 1, 1954

By B. Das

he flotation studies on hematite were carried out using di (2-ethylhexyl) Phosphoric acid (D2EHPA) as the collector. The possible mineral reagent interaction was studied through electrokinetic and dissolution studies. The shift in zeta potential (PZC) and decrease in dissolution of iron in the presence of D2EHPA indicated that D2EHPA was specifically adsorbed on hematite surface. The adsorption imparted necessary hydrophobicity for flotation of hematite. Hematite could be floated selectively from hematite and quartz synthetic mixture. Key words: Hematite, D2EHPA, flotation, electrokinetics, dissolution.

Jan 1, 2003

By Benito Barbabela e Silva

O pelotamento é a mais complexa etapa de aglomeração de finos de minério de ferro. Sua resposta é naturalmente oscilante, sendo bastante influenciada pelas características físicas obtidas nos processos de beneficiamento mineral que a precedem e tem papel crucial para a etapa de tratamento térmico de sinterização à jusante. O presente trabalho aborda o processo de classificação de pelotas verdes, sólidos singulares de aspecto deformável e pegajoso, em peneiras de rolos por modelamento por aplicação de Método dos Elementos Discretos. Esta técnica mostra-se como uma importante ferramenta pois supera as limitações impostas na modelagem física (quantificação e identificação de fluxos por ausência de instrumentação em escala industrial, amostragem sem representatividade) ao reproduzir de forma verossímil as repostas do sistema para importantes variáveis de controle: comprimento de gap, umidade, dispersão de tamanhos e resistência das pelotas.

Oct 30, 2017

By A. Duerksen

"Surface coal mining in West Virginia has supplied energy to the eastern coast of the United States for over a century. Over the years, the coal mining industry has been forced to adapt as societal demands regarding health, safety, and environmental impacts have changed. More recent pressure has called for another iteration of change: long-term post-mining sustainability. The research discussed in this paper investigates one potential solution - or component of a solution - to improve the sustainability of surface coal mining in West Virginia: post-mining wind power. The paper begins with an introduction to the Appalachian region of the U.S. and the role that mining has played in its history, followed by a discussion of the need for sustainable mining and how post-mining wind power may help fulfill it. Data processing methodology of field data from monitoring locations is then explained. The results are then used to estimate the electrical output of a wind turbine. This data is then utilized in a case study discussion of one of the monitored sites. The paper concludes with an analysis of the broader implications of the research and a discussion of future work."

Jan 1, 2011

By AIME AIME

A. A. Holland, Consulting Engineer, Toronto, Ont.-I noticed in this discussion of locations in which radium is found, no mention is made of the recent deposits discovered in Ontario. While radium is not a subject with which I am very familiar, I took an interest in this deposit on account of its novel occurrence. It is found in Haliburton County, near Wilberforce, Ontario, associated with a quartz free pegmatite, in a "break" that I understand can be traced for two miles. This "break" marks the contact between the limestone and syenite and contains numerous cavities or vugs. The gangue, on account of its deep purple, appears to :be amethyst.

Jan 1, 1930

Successful evaluation and exploitation of resources and reserves relies on the collection of high quality sample data. The quality of the sample data must be maintained through the application of a robust quality assurance and quality control (QAQC) program, including documentation of sampling procedures, training of sampling personnel and the regular monitoring of control samples. However, the application of QAQC programs in the minerals industry is often poor and the purpose misunderstood. It is all too common to have good quality control data collected, but no analysis work carried out until after drilling is completed. In a lengthy drill program, this can lead to problems not being discovered and corrected as they happen. Moreover, rectifying problems afterwards will be costly in terms of time and money, if not impossible. The consequences of poor quality sample data are many and include such effects as over- or underestimation of block grades, misclassification of ore and waste, and lower confidence in the resource/reserve models. The purpose of this paper is to highlight, using case studies, the importance of good QAQC practices to monitor the quality of sampling and laboratory sample preparation and analysis.

Mar 1, 2010

By J. W. Halley, T. S. Washburn

RIMMING steels derive their name from their action during solidification in the molds. As a result of incomplete deoxidation, gas is evolved during freezing, and the metal has a characteristic rolling action. The metal rises along the mold walls and descends in the center of the ingot. This action keeps the top of the ingot open and the advancing rim of solid metal can be seen. The rim grows until the rolling action is insufficient to prevent the top of the ingot from freezing or until the action is stopped by capping the ingot with a heavy plate. The violence of the reaction and its characteristics, such as growth or drop in the molds, are determined by the composition, the furnace practice, and the deoxidation in the ladle and in the molds. Though rimming steels represent a large proportion of the amount of plain carbon steel made, they have received comparatively little attention in the technical literature. The manufacture of rimming steels has been described by Hibbard, 1, 2 Fleming,3 Pierce4 and Jackson.5 The reactions occurring during rimming have been considered from the theoretical point of view by Chipman and Samarin.7 The structure of rimmed-steel ingots has been discussed by Nead and one of the present authors.6 Meyer,8 in studying segregation, investigated the distribution of carbon, sulphur and phosphorus in rimmed-steel ingots by analyzing the rim and core of blooms. In their studies of segregation, the Joint Committee of the Iron and Steel Institute and the British Iron and Steel Federations studied distribution in one billet and one ingot of rimmed steel.. A detailed study of the distribution throughout the ingot has not been published. The present investigation was undertaken to determine accurately the distribution of carbon, manganese and sulphur in normal rimmed ingots and the general distribution of other common elements present. The study included some work on the effect of pouring conditions and furnace practice on the distribution, though there is still much to be done in this direction. The structure of a rimmed ingot that has been split by dynamiting and a schematic diagram of the zones in the ingot are illustrated in Fig. 1.

Jan 1, 1938

By J. W. Halley, T. S. Washburn

Rimming steels derive their name from their action during solidification in the molds. As a result of incomplete deoxidation, gas is evolved during freezing, and the metal has a characteristic rolling action. The metal rises along the mold walls and descends in the center of the ingot. This action keeps the top of the ingot open and the advancing rim of solid metal can be seen. The rim grows until the rolling action is insufficient to prevent the top of the ingot from freezing or until the action is stopped by capping the ingot with a heavy plate. The violence of the reaction and its characteristics, such as growth or drop in the molds, are determined by the composition, the furnace practice, and the deoxidation in the ladle and in the molds. Though rimming steels represent a large proportion of the amount of plain carbon steel made, they have received comparatively little attention in the technical literature. The manufacture of rimming steels has been described by Hibbard,1,2 Fleming,3 Pierce4 and Jackson.5 The reactions occurring during rimming have been considered from the theoretical point of view by Chipman and Samarin.? The structure of rimmed-steel ingots has been discussed by Nead and one of the present authors6 Meyer: in studying segregation, investigated the distribution of carbon, sulphur and phosphorus in rimmed-steel ingots by analyzing the rim and core of blooms. In their studies of segregation, the Joint Committee of the Iron and Steel Institute and the British Iron and Steel Federation9 studied distribution in one billet and one ingot of rimmed steel. A detailed study of the distribution throughout the ingot has not been published. The present investigation was undertaken to determine accurately the distribution of carbon, manganese and sulphur in normal rimmed ingots and the general distribution of other common elements present. The study included some work on the effect of pouring conditions and furnace practice on the distribution, though there is still much to be done in this direction. The structure of a rimmed ingot that has been split by dynamiting and a schematic diagram of the zones in the ingot are illustrated in Fig. 1.

Jan 1, 1938