Search Documents

By Robert L. Lagace

This report presents a mathematical model for the propagation of UHF radio waves in the large cross-section tunnels of a room and pillar limestone mine, and describes the analysis of a small amount of propagation data obtained in a limestone mine. The model and analysis is based on the waveguide mode theory developed earlier for the transmission of UHF waves in coal mine tunnels, with allowance for propagation losses due to refraction into the tunnel walls, to scattering by wall roughness, and to long range random tilt of the walls. Propagation around corners and through pillars is also examined based on a ray theory approach, together with the beneficial effects of placing reflectors at intersections to significantly reduce corner losses. The theory is found to be in fair agreement with the data; however, additional in-mine measurements are needed to provide a more conclusive test of the model.

Jan 1, 1979

By Hannu J. Häkkinen

Metal clusters exhibit unique size-dependent physical and chemical properties that differ from those of bulk materials or large particles. Here we discuss recent theoretical investigations of the catalytic properties of free and MgO-supported gold clusters. The catalytic activity of gold clusters depends sensitively on the environment, charge state, and chemical composition of the catalyst. Relativistic bonding effects stabilize large planar structures for gas-phase gold clusters, and non-compact ?quasiplanar? structures are present as important isomers also for surface-supported clusters. The hybridization of the atomic 5d and 6s states is significantly enhanced by the relativistic effects, and large spatial variations in the nature of the local electronic structure make the low-coordinated gold atoms preferable adsorption sites for oxygen molecules. The adsorbed oxygen molecules are activated to superoxo- and peroxo-states via charge-transfer from gold, and Eley-Rideal and Langmuir-Hinshelwood reactions with CO proceed via low-barrier formation of intermediates, which do not require O-O dissociation as precursors. This facilitates the low-temperature (below 300 K) activity of gold nanocatalysts in CO oxidation. Other gold nanostructures, such as mono-atomic gold nanowires, may also become important prototype systems in chemical sensing and nanocatalysis; here we show that they are active promoters of hydrogen dissociation.

Oct 1, 2003

By B. L. Gibbs

The mining industry is constantly in a state of flux -boom or bust; mine openings and closings. Part of the reason is the nature of ore deposits -they are there or they are not. Once they are mined, they are reclaimed and the move is on to the next deposit. Risks are usually high, and payoffs can be great or not so great. Many factors go into making a property payoff, and mining companies are continually searching for ways to remain profitable as long as possible. Computers and the people who can make them work are one of the ways available to improve productivity and ensure this happens. Computers have been used in the mining industry for the last 30 years (and more in a few cases). During the past 10 years, the explosion of micro-computing has changed how many mining companies do their work.

Jan 1, 1993

By K B. Holm

This paper deals with the advances made at Syferfontein Colliery in the calculation and control of dragline methodology. The high capital outlay and operating cost of a dragline necessitates strict control of all aspects of the dragline operation. Before purchasing a dragline, a complete evaluation of all the parameters that can affect the viability, now and in the future, of the dragline operation needs to be completed. Such parameters as thickness of burden, material properties (swell), “castability”, pit width and pit length, etc. need to be considered.

Jan 1, 1994

By Gregory B. Poole

As part of a $3.5 billion program to improve the antiquated waste water system in the city of Atlanta, the Nancy Creek Tunnel is being constructed across the northwest portion of the city. This tunnel is over eight miles long and is being constructed using Tunnel Boring Machines (TBM) for the majority of the tunnel and conventional drilling and blasting for three shafts, starter and tail tunnels and four connecting tunnels, totaling 2400 feet in length. An extensive public relations program was developed for this project. A group effort by the owner, engineer and contractor produced a public relations program that both informed and educated the public of the anticipated perceptions and effects of the blasting and TBM activities.

Jan 1, 2005

By N. Yamazaki

The supply of clean copper ores, which have high copper concentration and low impurities like arsenic, has declined year by year. Therefore, both mine and smelter sides have to consider how to remove impurities like arsenic. We focus herein on arsenic as an impurity because it is an extremely important issue from the environmental point of view. Approximately 150,000 t of arsenic is input into the copper industry every year. A small part of it is mainly treated in the smelting side. For instance, Ministro Hales Limited, which is a mining corporation in Chile, has performed the calcination process to remove arsenic from ore with high-arsenic content. In the process, flue gas is washed by water, and the final residue is treated by a hydrometallurgical process. Many processes for arsenic removal in various stages have been proposed, and several bottlenecks exist to achieve it. One of the difficulties encountered is getting an assessment of the process, which depends on the countries and/or areas of operation. The standardization of the assessment procedure will be desired in the near future to keep the same environment standards all over the world, and now is the time to start making discussions on this matter. This will be the first step in making an international assessment procedure for arsenic treatment in the copper industry. INTRODUCTION Using the term “sustainable development” without any scientific basis can give people a false sense of security. Engineers and scientists must analyze the total mass flow of energy and materials and estimate local drain on the environment as well as the global impact of a particular industrial activity to ensure sustainability on this planet. The operations of the mining and smelting industries have a strong effect on the environment even if they provide useful materials for human beings. The copper mining and smelting industries have brought about serious environmental problems in the past. For example, the Ashio mine pollution caused big damage to the agricultural sector near the Ashio area in Japan in the late 19th century. One of the most serious problems at that time was SO2 emission because copper ore is sulfide, and the smelting process basically results to sulfur oxidation. The resource balance from a copper smelter in a year, assuming a total production of 16 million tons, can be summarized as follows: discarded minerals, 30 billion tons; sulfur, 16 million tons; iron oxide, 8 million tons; additional smaller amounts of other metals, electricity, and fuel.

Jan 1, 2019

By J. D. Doll

MSHA has promulgated a rule to limit the exposure of underground metal/nonmetal miners to diesel particulate matter (DPM). In May 2008, the final personal exposure limit will be lowered to 160 µg/m3 total carbon. To comply with this rule, mine operators are implementing a variety of control technologies. In this study two types of control technologies (ventilation and cabs) which are being implemented in limestone mines were investigated. Two stone mines in this study use large diameter propeller fans for main mine ventilation and direct the air to the faces using auxiliary fans, stoppings, and long pillars while bypassing the old mine workings. NIOSH measured for sub-micrometer elemental carbon (EC) using SKC DPM cassettes (analyzed using NIOSH 5040) and a near real time instrument. With the present ventilation and the number and type of vehicles used, the concentration of EC from DPM at the working areas was at or below 400 µg/m3 for both mines and about 166 µg/m3 and 251 µg/m3 at the returns. The real time data showed that the ventilation was reaching the working areas and effectively diluting the DPM. Environmental cabs were also used to reduce DPM exposures in three underground limestone mines. Using NIOSH method 5040 and near real time EC instrumentation, NIOSH sampled inside and outside of a loader cab at one of these limestone mines to determine the effectiveness of the cab. The cab was found to be over 90% effective in removing DPM as long as the cab system was properly maintained, and doors and windows were closed.

Jan 1, 2009

Inefficient conveyors suffer carryback, leading to the build-up of materials on idlers, and other expensive components. They spill and leak material at loading zones and transfer points, causing accumulations that can damage the belt, wear moving components, and increase both cleanup labor and maintenance expense. They wander or mistrack, spilling material and en- dangering personnel and conveyor components, including the belt itself. And through these inefficiencies, they multiply an operation's hidden costs-the dollars lost because of missed production, of increased downtime, of the expense for the replacement of prematurely worn or damaged equipment. In this paper, the author will examine the importance of belt conveyors to mines and process plants He will trace the state-of-the-art in systems for cleaning belts, and controlling the release of fugitive material from conveyor transfer points, by exploring the roots of the problems, and demonstrating solutions that have been proven to be effective. Included in these systems to improve material handling are transfer point stabilization and sealing systems, dual belt cleaning systems, and belt training idlers.

Jan 1, 1991

By Kain Petterson, P D. Katsabanis

Blast fragmentation, determined using image analysis was correlated to drill monitoring parameters in an open pit operation. Average fragment size and 80% passing size showed strong correlation with specific energy of drilling as well as with torque, while the same passing sizes did not correlate well with the rate of penetration. It was also determined that the uniformity of fragmentation decreases with the specific energy of drilling. Thus drilling monitoring parameters appear to be valuable in determining the blastability of the rock mass, enabling adjustment of blast loading to respond to changing conditions in the rock mass.

Jan 1, 2013

By Albert Ruiz

South Coast Water District (District) operates the Beach Interceptor Sewer Tunnel (BIST) in South Laguna, Orange County, California between Mon-arch Beach and Aliso Beach (Figure 1). The 10,424-foot long BIST houses a 24-inch Techite gravity sewer pipeline critical to the District Sanitary Sewer Collection System that conveys 1 MGD of raw sewage to a wastewater treatment plant. The original tunnel was constructed in 1954 and the sewer line replaced in 1974. Periodic inspections by sewer pipeline maintenance crews have documented deterioration of specific intervals of the tunnel within the past few years (Sancon 2003). Rotting timber supports and rock falls in the tunnel as a result of the deterioration were endangering the sewer pipeline. A 50-foot section of the tunnel was determined to be in need of immediate repairs, which were carried out from January to August in 2007. This section was enlarged to a horseshoe shape and lined with shotcrete. The pipe was encased in concrete in the invert of the new enlarged cross section. Hatch Mott Mac-Donald (HMM) designed the emergency repairs, carried out an assessment of the rest of the tunnel alignment, and is currently developing a work plan for rehabilitating the entire tunnel.

Jan 1, 2008

By R. H. Adams, A. M. Khan

The Huntington Beach oil field is on the Pacific Coast, southeast of the City of Los Angeles (Fig. 1). It lies both onshore and offshore. Most of the onshore section is operated by Standard Oil Co. of California, WOI. The Tar reservoir is of upper Pliocene age, about 200 ft thick, and consists principally of fine-grained, unconsolidated, somewhat shaly sand, with thin inter-bedded shale stringers throughout (Fig. 2). The reservoir is a broad, highly faulted, elongated anticline, with an areal extent of about 370 acres. Most of the faults bisecting the structure are normal, trend north-south, and are the main cause of reservoir discontinuity (Figs. 3 and 4). From 1964 to Dec., 1967, 259 steam stimulations were performed on a total of 125 Tar sand wells. Eighty-six new wells were drilled and steam stimulated. Of the total, 96 have been stimulated twice, 34 three times and 3 four times. During this same period, a two-injector steam drive pilot has been in progress. The response obtained from this project has been compared with the response to cyclic stimulation. This paper presents an analysis of the field observations for the two methods of thermal recovery. History of Development Drilling to the Tar pool commenced in 1924 with an initial well production of 40 to 50 B/D of 12o API gravity oil. Complete primary development of the pool has been spread over several years. Approxi- mately 40 wells were drilled during the first phase of development, which was completed in 1945. The subsequent primary development started in 1960 with initial well productions of 30 to 40 B/D oil. Thirty-seven wells were completed in the Tar pool during this phase. For the most part, slotted, gravel flow packed liners have been used in the wells in this pool. A cyclic steam stimulation pilot was initiated in March, 1964. Based on the very successful stimulation in the pilot area, the cyclic stimulation project was expanded to include all of the Tar pool wells producing at the end of 1965 (Fig. 5). Also, a development drilling program was begun at this time. To date, 86 new wells have been drilled under this program. The number of wells drilled each year in this secondary phase of development is also shown in Fig. 5. New Well Completion Practices Most of the new wells have been completed to produce from both the Upper and Lower Tar zones. Generally, a casing stub is cemented from the top of Lower Tar to the base of clean Upper Tar sands to exclude intermediate water-bearing sands. The water string is then cemented from the top of Upper Tar to about 1,500 ft with neat cement and 30 percent silica flour. The annulus from 1,500 ft to surface is then filled with a petroleum-based gel through a high-temperature port collar. Once again, a history of sand-free production dictated the use of 60-mesh gravel flow packed liners. The Upper and Lower Tar

Jan 1, 1970

By D Reid, J Vinod, M Rahman, A Fourie, T Vo, J Ayala, A Russell

This paper reports on an industry and Australian Research Council funded research project, TAILLIQ, that is a joint initiative between four Australian Universities. The paper discusses the accuracy with which the critical void ratio can be determined for a given tailings; it does this by presenting the results from a ‘round robin’ study in which 18 geotechnical laboratories around the world participated, testing the same tailings (sampled from a gold mine in Western Australia). The results were variable, although a reasonable number were very similar, as described in the paper. The paper provides additional test data for sandy silt gold tailings recovered from a sponsor’s site in Australia, including preliminary calibration chamber test data, results from direct simple shear tests and characterisation tests to determine unsaturated geotechnical properties.

Jul 1, 2021

By Vilkul Yuri

Operation of the iron ore deposits of Krivbass which has been going for 130 years, has led to serious problems related to reaching great depths in open pit and underground mining. Extraction of the huge volume of rock mass (about 9 billion m3) resulted in mass violations of the natural state of the subsurface. At present most mining operations are carried out either by combined open pit and underground mining or by open pits in areas underworked by underground mining. Now the process of movement of the strata underworked by underground mines is not completed ? work fronts of open pits approach the areas of possible funnel, terrace and fissure formation, movement continue to develop. With deepening mining operations the remaining reserves are worked off under layers of incumbent rocks of > 900 m. Significant underground voids arise from mining "blind" deposits at large depths. Heaving of voids over the mined area lasts for decades; it may result in not only unpredictable time of funnel emerging and area development of movement synclines, but also the threat of air blows in mines. Forced caving of incumbent rocks as a way of controllable backfilling is difficult to achieve for economic and technical reasons. This is much more expensive and dangerous than stoping. Furthermore, the mining practice does not know examples of enormous volume backfilling under a km thick rock layer. Currently, RMI "KNU" is conducting research and pre-design work directed at creating a specialized pilot Geoinformation System (GIS) of continuous remote monitoring of rock mass in areas of underground voids influence in Krivbass area. Implementation of this system will enable to determine promptly in time and space the areas of the beyond cut off stress condition, to inform about possible occurrence of events that may result in accidents and to improve safety of mining along with other systems of forecasting and controlling the stress condition in rock mass. RMI "KNU", with a large number of professionals from many Ukraine?s leading mining research centers, has developed a research and design work program that includes the following principal stages: 1. Analyzing geomechanical conditions of combined mining of magnetite quartzite and rich ore deposits; determining mechanisms of moving of rock strata underworked by underground mining and places of hazardous area monitoring. 2. Investigating anthropogenic factor influence on the safe state level of rock strata underworked by underground mining (laboratory studies). 3. Developing processing techniques for continuous remote monitoring of rock mass in areas of underground cavity influence. 4. Modeling the state of rock mass based on results of pilot GIS hardware measurements. 5. Developing an expert diagnostics system for rock mass state in areas underground void influence. 6. Experimental investigation and testing the GIS, its improving for efficient application. After testing the pilot GIS it is supposed to be implemented at all mining enterprises as an integral part of iron ore mining and processing technology in the Krivbass area.

Aug 1, 2013

By R. Boom, K. C. Mills, S. Riaz

This paper details the recent trends in slag-related research from 1999 to 2003. The trends in thefollowing are outlined: • Annual publication rate • Geographical origin of the work • Nature of the research (e.g. thermodynamics, kinetics) • Nature of the slag studied. This study has revealed that slag research in the USA and Europe has decreased to about a half over the last 20 years and that there has been a significant decrease in Japanese research in this area in recent years. However, these decreases have been offset by significant increases in Chinese and Korean research activity. There has been a significant increase in the amount of work carried out on the recycling and environmental aspects of slags in recent years.

Jan 1, 2004

By Christiaan Zeilstra, Jan van der Stel, Koen Meijer, Gerard Louwerse, Tim Peeters

The steel industry is producing about 5% of the world wide CO2 emission. Therefore the European steel industry has defined a research program to reduce the CO2 emission by 50% per ton: ULCOS. Since its start in 2004 ULCOS has identified four technologies for further development. Two of these technologies which produce liquid hot metal are discussed. The ULCOS blast furnace is based on recycling of decarbonated topgas and the capture and storage of CO2. The concept has been demonstrated during three campaigns at LKAB EBF in Luleå, Sweden. The smelting reduction process HIsarna is a combination of the cyclone-technology and Hismelt. The process has been demonstrated successfully in four campaigns at a pilot installation on the IJmuiden steelmaking site.

Jan 1, 2015

By Harold P. Rue

The problem of removing hydrogen sulphide from natural gas has become within the last few years one of major importance to the natural gas and petroleum industry. Several gas fields in the United States produce natural gas containing hydrogen sulphide, and a number of oil fields produce gas which contains hydrogen sulphide. 3 The percentage of hydrogen sulphide in natural gas produced in these fields varies from a fraction of 1 per cent to as high as 20.5 per cent by volume. Hydrogen sulphide is probably the most toxic gas associated with natural gas, and from the standpoint of health and safety it is important that the hydrogen sulphide be removed if the gas is to be used for domestic purposes. Hydrogen sulphide, besides being toxic and therefore a hazard to animal life, is under certain conditions an active corrosive agent and very destructive to equipment. The annual loss caused by the corrosive action of hydrogen sulphide on equipment amounts to hundreds of thousands, perhaps millions, of dollars. The largest percentage of natural gas produced in the United States comes from wells which also produce oil. This associated gas invariably carries with it light fractions of petroleum, which when separated from the gas, condense to the liquid form at ordinary temperatures and pressure. Commercial application is made of this natural condition, and "wet gas" is processed to obtain so-called natural gasoline by employing the principles of absorption, adsorption, or compression and subsequent expansion accompanied by cooling. In the manufacture of natural gasoline from wet gas which contains hydrogen sulphj.de, if this contaminating gas is not first removed, some of the hydrogen sulphide may oxidize to form free sulphur and water. The free sulphur will dissolve in the gasoline produced by any of the aforementioned methods and cause the product to be positive to the corrosion test and there-fore unsuitable for commercial use in that condition. The objectionable sulphur compounds can be removed by washing the gasoline with a solution of caustic soda or other chemicals, but this treatment is expensive. It is advantageous therefore to remove the hydrogen sulphide from the gas before it is processed in a natural-gasoline plant.

Jan 1, 1932

By H. Ogasawara

To study the preparation process of an earthquake, we should get closer to the hypocentre. In co-operation with ISS International, we had an experimental field (~200 m x~200 m) without dykes and faults in a South African deep gold mine. We have monitored more than 20,000 seismic events (M<2) with borehole tri-axial accelerometers. We used a data acquisition system with 15 kHz sampling and 120-dB dynamic range. In a remnant area at a distance of 100?200 m, an earthquake sequence associated with an M~2 event occurred. Significant changes in seismic parameters such as stress drop, b-value, energy index were observed associated with the sequence. We installed Ishii?s borehole strain meters and could monitor as large a strain change as 10-4associated with mining. However, sampling was only 4 times per hour and 12 bit A/D. A distance from the M2 sequence was ~100 m, being not close enough. Therefore, we found another field with several crosscut tunnels excavated across a fault where an M=2-3 event is expected. We installed the strain meter within several metres of the fault to monitor both shear and normal strains on the fault. The strains are continuously digitized with a 24-bit 25-Hz A/D conversion. The Earth Tide (10-8)is clearly detected. Seismicity induced by longwall mining can be compared to earthquake swarm induced by fluid intrusion to vertical dykes. We also found a decrease in energy index in the source area of M>5events a few days before the major events. Keywords: seismic monitoring, strain monitoring, seismic parameters, preparation process of an earthquake, South African gold mine.

Jan 1, 2002

By M. Lange

The postulation that primary platinum group metal (PGM) matte will chemically react with magnesia-chrome bricks when temperatures exceed 1500°C was tested. Magnesia-chrome brick samples were heated in contact with matte at 1300°C to 1750°C for 30 minutes, after which the refractory samples were analysed using reflected light microscopy and scanning electron microscopy. The samples were all completely penetrated by matte. As the temperature increased the matte also penetrated the fused aggregate grains and disintegrated them. The chromium concentration of the matte inside the refractory samples was found to be slightly higher than that of the bulk matte. At temperatures of 1500°C and higher, MgO, FeO, and magnesium-rich silicate crystals could be identified in the matte directly adjacent to the refractorymatte interface. Phase relations clearly indicated that chemical reactions take place between primary PGM matte and the magnesiachrome refractory material at temperatures above 1500°C, but that these reactions are more complex than expected from FactSAGE® calculations.

Jan 1, 2014

The Bureau of Mines performed cratering experiments in a homogeneous granite to test scaling laws for charge weights of 0.00476, 0.0220, 0.0900, 0.304, and 1.03 lb. Agreement among the data was best when empirical scaling exponents greater than one-third were assumed. Although the analysis showed that the best empirical scaling exponents were 0.37 for crater volume, 0.38 for crater radius, and 0.39 scaling for crater depth, all three crater dimensions could be scaled with a 0.38 scaling exponent.

Jan 1, 1970

By Frances Badelow

This paper describes a design process for piled raft foundations supporting high-rise buildings. The design process comprises an initial stage of geotechnical site characterization using the results of investigation boreholes to prepare a subsurface model and derive geotechnical parameters for raft and pile design from empirical correlations. Following this a preliminary analysis is undertaken using a combination of elastic theory and allowances for non linear behaviour of the piled raft system to assess the viability of such a foundation system and any potential advantages of a piled raft over conventional fully piled foundation systems. Finally, a detailed analysis is undertaken using the GARP8 computer program. Case studies where this design process has been successfully used to design a more efficient piled raft system that has resulted in significant cost and time savings compared to conventional bored pile foundation options are also described.

Jan 1, 2006