Search Documents

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillars is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to pre-failure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25 to 40 percent higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Pre-failure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to improved designs as mines become deeper.

Jan 1, 2001

By Paul F. Gnirk, Ralph A. Wagner, Joe L. Ratigan

This thermomechanical analysis used the finite element method to investigate the behavior of crushed salt backfill in a waste disposal room situated in a salt dome repository. The first of two objectives was to determine the transient temperature rise and degree of thermomechanical consolidation that occur in the backfill as a function of drillhole depths. The second objective involved the evaluation of closure due to salt creep of unlined emplacement drillholes and the determination of pressure on steel sleeve liners in the drillholes should liners become necessary for canister retrieval. The retrievability period was considered to extend for 25 years after waste emplacement. The canisters were assumed to contain ten-year old high level waste with a thermal output of 4.3 kW at the time of emplacement.

Jan 1, 1981

By Lewis Blanchard Brown

It is my purpose in the following paper to describe the south-central part of Siberia, with special reference to its geology and the mineral deposits. This region is known politically as the Achinsk and Marinsk districts of the Tomsk Government. It is situated among the Altai mountains, in. ]at. 50° to 55O n and long. 87O to 93O E., not far from the northern frontier of Mongolia, and is divided as follows: Mining Districts.—(1) The Tomsk mining district, including the political districts of Altai (belonging to the private crown lands of the Russian Emperor) and Marinsk; (2) the AchinskMinusinsk mining district, including the political districts of Achinsk and Minusinsk; and (3) the North Yenisei mining district, situated in the northern part of the Yenisei political district of the Yenisei Government. Fig. 1 is a map of the Tomsk mining provinces, showing the useful mineral-deposits, excepting those of gold, and giving the routes of the railroads and post-roads connecting the various districts. Political Divisions.—The Tomsk Government is sub-divided into seven " oojesdy " or districts, as follows: Barnaul; Biisk; Kuznetsk; Kainsk; Kolyvan; Marinsk; Narim; and the Altai district (private land, as above). The Yenisei Government is sub-divided into five "oojesdy" or districts, as follows : Erasnojarsk ; Kansk; Yenisei; Achinsk; Minusinsk. Concerning the geology of the region, in addition to the record of my own observations, references will be made to the works of earlier writers. These have been consulted for the purpose of comparison, as regards the districts which I have actually traversed, and for the purpose of completing my account of such portions as I have not been able to visit.

Jan 1, 1904

By Geoffrey G. Huggins

Discussions are presented of the three phases of the noise reduction program on flight-type coal conveyors. The three phases are identification of noise sources, evaluation of potential noise reduction concepts, and implementation of noise reduction which is intended to reduce conveyor noise to less than 90 dB(A) in the underground mining environment. The major noise sources are impacts of the chain on the tail roller and on the top and bottom decks. A total noise reduction of 11 dB(A) was achieved by using techniques which are applicable to retrofit. These are a vibration isolated tail roller and an isolated wear strip on the return deck. A theoretical model of isolation provided by the isolated tail roller is developed. Appendices are presented which contain information on other potential concepts and additional data generated.

Jan 1, 1976

Studies were carried out to examine the effect of introducing varying levels of a pisolitic limonite (Yandi) into an Australian iron ore blend. Compared with other ores in the blend Yandi is more porous. This structure is found to have a considerable effect on the sintering behaviour of the blends. Pilot-scale sintering studies and plant trials showed that sinter plant productivity, sinter reducibility and the low-temperature reduction degradation index altered significantly when the level of Yandi in the ore blend exceeded 15 wt%. The improvement in the reducibility is thought to be a direct result of increased porosity in the sinter and the presence of highly reducible pseudo-relict haematite. Plant trials have also shown that operational changes could be made to the sinter plant to avoid potential deterioration of productivity

Dec 1, 1991

By Manish Kumar Jain

The mineral industry in India is an important contributor to the country?s GDP and foreign trade, and also a significant source of employment generation. The industry is distributed almost all across the country and has operations in some of the remotest areas, where it has also served as a sole source of infrastructure development. India produces 89 minerals, out of which four are fuel minerals, 11 metallic, 52 non-metallic and 22 minor minerals. The mining leases are occupying about 0.21% of the total land mass of the country. Indian mining industry is characterized by a large number of small operational mines (approx 3000 mines). Appropriate systems have been put in place to ensure sustainable growth of the sector, which include formulation of procedures for scientific prospecting and mining and development of a mechanism of prior environmental and forest clearances for mining projects. Main emphasis is to protect the health and safety of mine workers, as well as to safeguard the interests of indigenous people through rehabilitation and resettlement packages. Efforts are under way to mainstream the artisanal and small-scale mining sector in order to promote equity in the mining industry. The issue of scientific closure and reclamation of the abandoned mine sites poses a major challenge. Present paper illustrated several initiatives have been taken in this direction along with case studies, which could be replicated in other parts of the country.

Aug 1, 2013

By Schlanger H. P

A theoretical model for gas outbursts in underground coal mines is as follows. An outburst is the structural failure ofcoal due to excess stress resulting from body forces caused by gas pressure gradients. These body forces influence the stability of a mine face in the same manner that gravitational body forces affect the stability of the roof of a mine. The magnitude ofthese body forces can be appreciated when it is realized that for an average density coal, the gravitational body force is equal in magnitude to the force from a gas flow with a pressure gradient of 14 kPa m-I. Gas pressure gradients and the resultant stresses within a seam can be calculated with numerical methods. Thus, providing the necessary parameters can be measured or estimated, in principle the theory can be applied to compare the outburst risk of various mining arrangements.

Jan 1, 1985

By K Kermanshahi, J Allen, MáHilden, M Powell, S Mwansa, S Palaniandy

Approximately 420 VertiMills« (VTM) have been installed in mineral processing plants throughout the world, mainly in tertiary and regrind applications plus several in secondary grinding duties. Metso Minerals (Metso) and the Julius Kruttschnitt Mineral Research Centre (JKMRC) have commenced a collaborative research program in stirred milling technology focusing on mill performance evaluation, model development and scale-up methodology. Industrial VTMs are being assessed using a consistent circuit survey protocol to evaluate the performance of VTMs in comminution circuits. The survey protocol includes identification and modification of sampling points, appropriate sampling techniques, controlled circuit stability, and best sample analysis practice. To initiate this study four surveys were conducted in the tertiary grind circuit in the Ridgeway Concentrator at Cadia Valley Operations (CVO) that treats the full circuit throughput of over 800 tph. To deal with the high feed rate the site opted to lead the world in the application of stirred mills by installing the largest VTM, at 3000 hp (2240kW) in closed circuit with a hydrocyclone bank. On average the operating work index was 13.1 kWh/t, reducing the secondary grind product by 40 - 50 ¦m to the required 80 to 100 ¦m range. The applied specific energy is relatively low in these low-intensity stirred media mills at 2.7 kWh/t. The size specific energy was 24.2 kWh/t-75¦m. Based on the survey and operating data the VTM circuit is performing well in this high-throughput tertiary grinding application, producing a sub-100¦m product.CITATION:Palaniandy, S, Powell, M, Hilden, M, Kermanshahi, K, Allen, J and Mwansa, S, 2013. VertiMill« - Development of circuit survey and performance evaluation protocols, in Proceedings MetPlant 2013 , pp 162-175 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Gray Mullins

This paper presents experimental results from a study to assess the interface bond between a cast-in-place concrete seal slab and prestressed concrete piles in cofferdams. Three different seal slab placement conditions - fresh water, salt water and bentonite slurry - were evaluated and the results compared against controls where no fluid had to be displaced by the concrete. Normal pile surfaces were investigated. Additionally, the situation of ?soil caked? piles was also investigated. Both model and full-scale tests were conducted. In the model tests, twenty eight 15 cm square prestressed sections were used with the embedment depth varied between d-2d, where d is the width of the pile. In the full-scale tests, 16 specimens were tested. The prestressed piles were 36 cm square with the embedment varied between 0.5d-2d. Four of the sixteen piles were cast with embedded gages located at the top, middle and bottom of the interface region. The results showed that loads were transferred to the piles over an effective area, not the entire embedded depth. Significant bond stresses developed even for the worst placement condition. Recommendations are made for revising current values in specifications.

Jan 1, 2013

By W. J. Verner, J. R. Lucas

Billions of tons of bulk solid materials are processed through our industrial plants each year, and the tonnage is steadily rising. It has been estimated that for every dollar spent in industry as a whole, approxinlately 30 cents is consumed in the handling of bulk solid materials. It is in this category that tremendous savings are possible through the use of improved techniques. Since World War 11, the mining, steel, chemical, and grain industries, among others have made use of increased materials-handling automation in order to gain some of these savings. However, in a chain of automatic operations, every link must be completely reliable, for if there is a single failure, the whole system immediately becomes ineffective. Only too often the weak link in the chain proves to be the flow of bulk solids from bins. To contribute to the fundamental knowledge in this area, a research study has been continuing at The Ohio State University. The principal objective of the investigation has been to study the internal stresses existing in confined bulk solids. LITERATURE SURVEY Literature studies have revealed that many outstanding people have made contributions to the field of bulk solids. For instance, C. F. Jenkin,1 suggested: a. The pressure on a bin wall is not directly proportional to the depth beneath the surface of material in the bin. b. The vertical pressure distribution on the base of a bin is not actually uniform but is a variable. c. Arches form in bins as a result of very small deformations of the material in the bin. This deformation causes a series of gaps to appear, and consequently causes the disappearance of diagonal forces that cannot act across these gaps. The removal of the diagonal forces causes horizontal forces to be introduced which seem to be the chief cause of arching. 11. A. Janssen,4 in 1895 in connection with his experiments on bins, derived a differential equation to describe both the lateral and vertical pressure in bins with vertical sides. This represents a significant contribution to bulk solid theory, and thus its solution is reproduced as follows: L = KV = RW/U' [l-e -U'KY/R] I where L is the lateral pressure of the bulk solid in psf., V is the vertical pressure of the bulk solid in psf., K is the ratio of the lateral pressure to the vertical pressure at any point, R is the hydraulic radius of the bin in feet, W is the density of the bulk solid in lbs. per cubic feet, U' is the coefficient of friction between the stored material and the bin wall, and Y is the head of material above the point in question in feet. In 1903, Jamieson,6 in an elaborate series of experiments on full sized bins measured vertical and lateral pressures by hydraulic diaphragms. He determined many values for mediums of corn, wheat, peas, and flaxseed. In 1951, Caughey, Tooles, and scheer3 measured both lateral and vertical pressure in deep bins by using strain guages on steel bands. Values were calculated for cement, gravel, sand, soy beans, shelled corn

Jan 1, 1961

By Helene Kennedy, Josef Macsik, Yvonne Rogbeck, Gregory Makusa, Göran Holm

"Constructions activities in cities often imply large volumes of surplus material which could be treated by stabilization for re-use in new geotechnical constructions. Modification of dredged sediments by e.g. stabilization/solidification (s/s) is an example of sustainable handling option implying dredged contaminated sediments to become a potential resource for civil engineering constructions. The SMOCS project (Sustainable Management of Contaminated Sediments) within the Baltic Sea Region Programme 2007-2013 has developed a guideline based on a sustainability approach free to download at www.smocs.eu. The paper presents key issues in the guideline and highlights the importance of performing a field test as part of the design process. Two field tests with s/s-treated dredged sediments for new port areas are presented. Strength, permeability and leakage properties of s/s-treated contaminated sediments make beneficial use in geo-constructions possible. The influence of possible physical/chemical deterioration processes on the durability has been studied showing that freeze/thaw cycles might degrade the monolith of s/s-treated sediments. Consequently s/s-constructions shall be below freezing depth. Other deterioration processes such as salt and sulfate penetration were found of minor importance. Research is on-going to study the influence of and how to cope with freeze/thaw cycles on the long-term properties.BACKGROUNDConstructions activities in cities often imply large volumes of surplus material which could be treated by stabilization for re-use in new geotechnical constructions. The mechanical and environmental properties of the contaminated sediments could be modified through the stabilization/solidification method (s/s method) and provide a potential resource for civil engineering constructions. The SMOCS project (Sustainable Management of Contaminated Sediments) within the Baltic Sea Region Programme 2007-2013 has developed a guideline on management of contaminated sediments based on a sustainability approach. A field test on the application of the stabilization/solidification method for treatment of dredged soft contaminated sediments was implemented in the Port of Gävle, Sweden. The treated sediments were beneficially used as fill material in the new port area replacing ending natural resources."

Jan 1, 2015

By Daniel G. DiCanio

This report describes a computer-based model for estimating the tangible costs of injuries and deaths from work-related accidents in underground coal mines. The study undertook to identify and quantify the elements of accident costs, including field visits to coal mines, insurance carriers, and public agencies. The mathematical models developed for each tangible element of accident cost are presented in Volume I of the report. A listing of the computer programs which comprise the model and instructions for using the programs are presented in Volume II. Statistical distributions of mining family characteristics, data on 95 miners killed in underground accidents, and other basic data used to develop the model are presented in Volume III. Application of the model to a data base of 9,286 accidents which occured in underground bituminous coal mines during 1974 yielded a total of $56,900,000 in tangible costs to industry, mining families, and public agencies. Loss of income to the families of miners injured or killed in these accidents accounted for 47 percent of the total.

Jan 1, 1976

By Paloma Lazaro, Moe Momayez

Heat-related illnesses (HRI) are relatively common in both hot surface and underground mining operations. When workers are exposed to extreme heat or strenuous work in a hot environment, they become prone to heat stress. Heat strain is the result of the body’s response to external and internal heat stress. It is therefore vital for the conditions leading to heat strain be detected and treated in a timely manner. Heat-related illnesses are manifested by exhaustion and heat stroke. The predicted heat strain (PHS) [ISO 7933 (2004)] model has been developed to predict the health condition of the worker in terms of core body temperature and water loss. The PHS model tested in this study is based on eight physical parameters that are measured at different intervals during a work shift. They include air temperature, humidity, radiation, air velocity, metabolic rate, clothing insulation, posture, and acclimatization. The model predictions are then compared with a direct physiological measurement, such as core body temperature. We present the results of an extensive study that monitored and predicted body’s response to heat stress under different environmental and working conditions. The PHS model provided reliable results in most instances in comparison with other prediction methods currently in use in the field.

GENTLEMEN, lt is with much pleasure I meet you tonight at this the second meeting of the Australasian Institute of Mining Engineers, held in Western Australia, and I sincerely thank you for the honour you have conferred upon me in electing me as your President. I greatly appreciate the distinction, and will endeavour to fulfil the duties of the office to the best of my ability, and hope to prove a worthy successor to those gentlemen who have held the position before me. On behalf of the local members of the Institute, I extend a hearty welcome to the members from the other States of the Commonwealth, who have come so far to attend this meeting, and also to the non-members whom we have invited this evening. We are especially pleased to have Mr. Gregory, our Minister of Mines and Railways, and the Government and School of Mines officials with us; and I take this opportunity to thank the Premier, Mr. Gregory, and the Government officials for the assistance given us, and for doing so much to make the visit of our members from the other States so pleasant and instructive. I have also to thank the Mayor and Councillors of Kalgoorlie for the courtesy and hospitality given to our members, which is much appreciated.I assume you want me to follow the time-honoured custom of giving a Presidential address...

Jan 1, 1909

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

By D. W. Smith, Robert F. Mehl

It has been shown by numerous studies that the orientations of new metal crystals are determined by the orientations of the crystals in the original matrix, whether these new crystals are formed by recrystalliza-tion, by precipitation from solid solutions, or by transitions in the solid state. The orientations of crystals formed by recrystallization of cold-worked metals that bear preferred orientations are occasionally simply related to the initial preferred orientation; often, however, the relationship is not simple, but complicated and obscure in origin.1 The orientations of crystals formed by precipitation from solid solutions have been shown by many studies in this and other countries to be determined by the orientation of the crystals of the solid solution stable at the higher temperatures, though here again complicated cases have been found and no general theory is available.2 Related to this latter class are the relationships found in crystals formed by suppressed transforma-

Jan 1, 1935

By John Wilson

This report describes the performance of Phase I of a project to design, analyze, and demonstrate a multilift longwall mining method applicable to mining coal seams twelve (12) feet or more in thickness. A non-simultaneous multilift operation is the most viable thick seam mining technique for introduction to the United States coal industry. In the case of the proposed site at Emery, Utah it will result in an increase in coal extraction from 30% with present methods to at least 50% and possibly more. The major technological advance involved in this project is mining a lower lift under a previously mined upper lift. To accomplish this, entries must be developed and maintained beneath the upper lift gob. This will necessitate the use of steel supports at frequent intervals throughout the lower lift' entry system. This has not been done in the U.S. to date. An economic analysis of the project indicates that, while this method will result in a higher than average cost per ton for coal mined, the coal would be competitive with current-operation in the area.

Jan 1, 1976

By C. M. McKinney

The Bureau of Mines analyzed 626 crude oils from 546 oilfields in the United States that produced 2,500 BOPD or more during at least 1 of the last 3 years. Included also are crude oil analyses from eight fields that produced less but which were located in areas having few or no fields that produced 2,500 BOPD. The tables show the geographical and geological source, general characteristics. and determined and computed analytical data for each sample. The analyses were made according to the Bureau of Mines routine method and are directly comparable to other previously published analyses.

Jan 1, 1966

By P. N. Anyalebechi

The effects of solidification rate on the cast microstructures of aluminum alloys 6009 and 6016 have been investigated with directionally cooled laboratory-size ingots, at 0.2-10.1 K/s and 0.4- 23.1 K/s, respectively. These ranges of solidification rate are within those observed in commercial-size ingots. In both alloys, the average dendrite cell size and second phase particle size decreased with increase in average solidification rate and with a decrease in average local solidification time. However, at comparable solidification rates, the dendrite cells and second phase particles are finer in the shorter freezing range alloy 6009 than in the longer freezing range alloy 6016. This is provisionally attributed to the earlier formation of second phase intermetallics at higher temperatures during solidification and to the formation of greater amount of the relatively coarse plate-like ß -phase (Al9Fe2Si4) phases in alloy 6016. In general, in both alloys, the types and relative amounts of the second phase particles in both alloys are independent of solidification rate.

Jan 1, 2006

By Sam Tour

WHAT is a die-casting and what is the die-casting industry? From the literal translation of the words "die" and "casting"' one concludes that a die-casting is a casting made in a die. The casting may be of any metal or alloy or, for that matter, may be of some nonmetallic material capable of being cast, such as plaster of paris or glass. The die may be of any material that will take successive casts so it need not necessarily be metallic in nature. The term "die-casting," therefore, is indeed broad, though in practical usage it has come to mean the casting of metals and their alloys in metallic molds or dies. Even this limitation of the term leaves -a broad field, for castings may be made in a number of different ways. For example, the molten metal may be allowed to run into the die by gravity it may be sucked into the cavity of the die, it may be forced to take the contour of the cavity in the die by centrifiugal force, or it may be forced into the cavity under hydrostatic pressure. In England, castings made by practically all of these

Jan 1, 1935