Search Documents

By John P. Gooch

The solubility of 1,1,2,2-tetrabromoethane (TBE) in water was determined from 1.0° to 97.0° C. The solubility (S) of TBE in grams of solute per 100 grams water was correlated with [S = 1,920.55 [exp (40292L7 11, T2 10 T 737.577 + 9.923962 ] where T is in degrees Kelvin. A thermodynamic analysis conducted on a system consisting of a TBE phase and a water phase in equilibrium with a vapor phase led to the calculation of the activity coefficient, vapor-liquid equilibrium distribution coefficient, relative volatility, and heat of mixing for saturated solutions of TBE in water. Data required for these calculations were the solubility of TBE in water and the vapor pressures of TBE and water as a function of temperature.

Jan 1, 1972

By Louis W. Cope

Since its discovery, Cuba has been called the “Pearl of the Antilles.” The country remains that, albeit a little tarnished these days. In Havana, many of the buildings are being refurbished, while some new ones are under construction. Since 1991, the laws have been relaxed so that Cuba is developing a mixed economy of central control with free market. Joint venture agreements have been signed with businesses from many countries. This does not include the United States due to its embargo. But even these regulations have been relaxed some.

Jan 1, 2003

After a short theoretical comparison of various typical large bell tops with the bell-less top for segregation and other ,ffects on the material flowing through the equipment proper, a comparative analysis between classical and the new burdening in the furnace is given, showing the theoretical effects of distribution and segregation on the horizontal pressure variations, temperature values and gas composition in the stack. Then some typical theoretical charging patterns of the bell-less top for wall and centre temperature adjusting, pressure drop corrections, dissymmetric local action for blow-in and scaffolding are described. Finally the available practical results on furnaces equipped with the bell-less top are compared with the theoretical statements made before and conclusions indicate that the new approach to burdening blast furnaces is a real improvement.

Jan 1, 1975

By M. Perolo, A. Contini, E. Ramelli, G. Borgonovo, L. Locatelli

This paper presents the ground settlement monitoring system used during the construction of two tunnels bored by two EPB TBMs, beneath the existing and active railway embankment in Bologna (Italy). The tunnels run close to large buildings and beneath bridges and other infrastructure. Data are collected from remote total stations and from electro levels installed directly on the railway tracks. The automated monitoring system acquires and analyses data then sounds an alarm in the event that there is a problem. Alarms are sent out in case of excessive tilt or settlement. Data is provided through a dedicated web application for multiple-party access, to gather, manage and store monitoring data.

Jan 1, 2007

By Barrie Robb

Outline 1. Mackenzie Aboriginal Corporation (MAC) 2. ACR background 3. ?Learning from Experience? project - What - Why - lessons 3. How Industry could contribute to sustainable Aboriginal communities 4. Concluding words What is the Mackenzie Aboriginal Corporation (MAC)? ? Aboriginal owned ? Established construction capabilities ? Commitment to development of northern resources ? Partners have extensive experience

May 1, 2008

By Sergio Neves Monteiro

In the present work, a ceramic foam elaborated with illitic clays was characterized. Properties related to density and compression strength were determined in samples fired at 1300oC, a temperature that permits the clay structure to generate and retain gases that will produce the foamy structure. The microstructure of the ceramic foam was studied by X-ray diffraction, scanning electron microscopy and mercury porosimetry. The results showed that the ceramic foam presents a bulk density of 0.38 g/cm3. The microstructure is formed by large open pores, quartz particles and vitreous phase.

Jan 1, 2006

By C. W. Morris

This Final Report describes the major technical activities that were accomplished to produce a comprehensive continuous miner training system (CMTS) for coal industry utilization. The primary product of this program was a continuous miner part-task trainer. It is composed of an interactive computer graphics system combined with the operating controls of a continuous mining machine mounted in a simulated cab. The cab contains an audio system for reproducing continuous miner operational sounds. The trainer is supplemented with a complete set of cognitive materials that provide instruction in the operation, safety and health of continuous miner operations. A complete summary of the field test and evaluation of the CMTS is provided along with a set of recommendations for further training program refinements, expansions, and utilization.

Jan 1, 1982

By W. R. Paterson, W. Morton, D. B. Cameron

The Massbal II computer simulation program has been used to develop a general framework for the building of thermochemical models of metallurgical processes. The framework allows the rapid, simple construction of complex models of process equipment for use in flowsheet design, planning and plant operation. Application of the program to model the iron-making blast furnace and a flash smelting process is described

Apr 1, 1991

By Freeman Bishop

More than a few discussions are taking place these days among management economists seeking a way out of the dilemma of lower productivity vs. higher labor costs. Most suggestions would be illegal under present antitrust laws. Otherwise interindustry cooperation could be used to divide up some of management's tasks. Or price structures might be tuned to the special machinery and skills of some plants. Both remedies would be under attack almost immediately. There is one other remedy that is getting lots of attention: some form of compromise between management and labor to phase out no longer needed work practices that unions insist shall be retained. Railroads are the national industry suffering the most from this disease, still known as "featherbedding," an epithet coined by the railroaders themselves.

Jan 1, 1971

Filtration systems with disposable filter elements (DFEs) are used in the underground coal mining industry to control particulate matter emissions from diesel-powered permissible and nonpermissible coal mining equipment. This study was conducted in underground mine conditions to evaluate three types of high-temperature DFEs used in those filtration systems. The DFEs were evaluated for their effects on the concentrations and size distributions of diesel aerosols and concentrations of nitric oxide (NO) and nitrogen dioxide (NO2). Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. After an initial DFE degreening period, the filtration system with all three DFEs was found to be very effective at reducing total mass concentrations of aerosols in the mine air. The effectiveness of DFEs in filtering aerosol mass was found to be a function of the engine operating conditions. The efficiency of the new DFEs significantly increased with accumulation of operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on performance of the DFE elements. The effectiveness of DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for both DPFs and DFEs when the engine was operated at high-load modes than at low-load modes. Initial heating of certain DFEs resulted in visible white smoke and substantially elevated aerosol number concentrations. The effects of the DFEs on total nitrogen oxides (NOX) concentrations were found to be minor. The NO2 fraction was found to be generally lower for the DFEs than for the muffler. The engine-out NO2 fraction of the total NOX was found to be substantially higher for low-load modes than for high-load modes.

Jan 1, 2011

By J. Tuzo Wilson

"AT ANY TIME, it is a pleasure to me to be invited to address The Canadian Institute of Mining and Metallurgy because it represents an industry and men with whom I have been happily, if peripherally, associated continuously for forty years. This year, it is a particular pleasure because I believe that an important subject has arisen which I propose to discuss.This is a major discovery in the earth sciences, first fully revealed this winter, but already widely accepted. The basis of this revolution, for it is no less, is that measurements of three different features of the earth all change in exactly the same ratios. These ratios are the same in all parts of the world. The results from one set are thus being used to make precise numerical predictions about all the sets in all parts of the world. No such accurate correlations and predictions have ever been found before in geology or areal geophysics. The whole subject of earth science has thereby been radically altered.The first of these measurements is that of the direction of magnetic polarity in lava flows. When piles of young lavas are examined with the aid of a pocket compass, it is noted that some flows are magnetized in the direction of the earth's field and some in the reverse direction (Figure 1). By accurately dating enough flows, a time scale of the dates of reversals has been established. During the past four million years, nine reversals have occurred synchronously all over the world (Cox, Darymple and Doell, 1967, McDougall and Chamalaun, 1966) (Figure 2). It appears that the scale can be extended back to Precambrian times (McMahon and Strangway, 1967). This time scale is the first of the 'three identical ratios."

Jan 1, 1968

By M. Reza Saberi, T. Ted Miyake

Driven piles are a common tool in any engineer’s toolbox for supporting large structures over very soft ground, especially in high seismic risk zones. Challenges include achieving sufficient vertical and lateral load capacities within the constraints of pile spacing and geologic conditions. This was the case for a project in Orange County, California with a state-of-the-art, $180 million plant for biosolids processing, biogas management and energy recovery located in marshland next to an existing waste water treatment plant. The new construction for the Irvine Ranch Water District included a 70-foot (21 m) tall building and three closely spaced, 90-foot (27 m) high, 65-foot (20 m) diameter, egg-shaped steel digester tanks. The lower 35-feet (11 m) of the tanks were constructed below ground level. The site was underlain by up to 45 feet (14 m) of highly compressible peat and organic clays with standard penetration test (SPT) blows as low as 2 blows/ft (30 cm). Some of the peat layers had measured in-situ dry densities of less than 30 pcf (480 kg/m3) with moisture contents of over 250 percent. The soft clays and peat were underlain by a dense layer of sand and gravel at depth. Groundwater was very shallow. While nearby sites were designated by others as seismic site class “D”, this site was clearly class “F” (SF) which required site specific seismic hazard and time history analyses. Six recorded time histories were selected from the 1994 Northridge, 1989 Loma Prieta (California) and 1999 Chi Chi (Taiwan) earthquakes for the ground motion analysis considering the magnitude of the earthquake, distance to the source, characteristics of the earthquake source (i.e. type of fault displacement), peak ground acceleration, local site geology, station type (i.e. free-field or small structure stations), and spectral content that was similar to the period range of interest. Following ASCE’s Guideline Document 7-05, a site-specific horizontal acceleration response spectra (ARS) was developed for the maximum credible earthquake (MCE) associated with the site.

Jan 1, 2018

By AIME AIME

LOCAL COMMITTEES. EXECUTIVE.-W. A. Lathrop, Chairman; R. V. Norris, Secretary; S. D. Warriner, Treasurer; Irving A.. Stearns, W. J. Richards, H. S. Drinker, C. D. Simpson. GENERAL RECEPTION.-Irving A. Stearns, Chairman. Archibald, James, Jr., Pottsville. Lawall, E. H., Wilkes-Barre. Ashley, H. H., Wilkes-Barre. Lentz, W. 0., Mauch Chunk. Ayres, WV. S., Hazleton. Lewis, Albert, Bear Creek. Beard, J. T., Scranton. Loomis, W. H., Jeddo. Bridgman, J. C., Wilkes-Barre. Markle, Alvan, Hazleton. Bunting, Douglas, Wilkes-Barre. Markle, John, Jeddo. Chase, F. M., Wilkes-Barre. Neale, J. B., Minersville. Coroner, Eli T., Scranton. Norris, R. V., Wilkes-Barre. Cote, E. B., Jr., Drifton. Oliver, Paul A., Oliver's Mills. Davies, W. H., Hazleton. Owens, W. D., Pittston. Davis, H. G., Dorranceton. Pardee, 1. P., Hazleton. Dodge, W. F., Wilkes-Barre. Quin, R. A., Wilkes-Barre.

Jul 1, 1911

By John B. Goddard

In-situ leaching of uranium by aqueous ammonium carbonate containing oxygen or hydrogen peroxide as oxidant results in the partial dissolution of sulfides. While some of the sulfide sulfur is oxidized to sulfate, a considerable portion is oxidized only to thiosulfate and polythionates. Polythionates poison the anion exchange resin used to extract uranium. At the Palangana operation in southeast Texas, the trithionate ion (S3062-) was found by infrared spectrometry to be the major resin poison. Treatment of ion exchange feed solutions with hydrogen peroxide only resulted in partial conversion of reduced sulfur species to sulfate, and trithionate conversion was particularly slow. Poisoning of the resin also occurred from the ammonium chloride eluant, which built up trithionate because of recycling. This was essentially eliminated by chlorinating the eluant prior to yellow cake precipitation.

Jan 1, 1984

By D. B. Dreisinger

The zinc pressure leach process developed by Sherritt Gordon, Ltd. permits the direct leaching of sulphide concentrates according to the overall reaction, ZnS +H,zS04 +402.+ZnS04+H20 +S0 The kinetics of the leach are affected by three rate controlling steps; ( l) oxygen mass transfer from the gas to the leach solution, (2) homogeneous oxidation of ferric ion to ferric ion by dissolved 011.ygen and (3) ferric ion leaching of zinc sulphide in the presence of a sulphur dispersing detergent (lignin sulphonic acid). Fundamental studies have been conducted to identify the factors that influence the kinetics of each individual rate controlling step. Oxygen mass transfer studies have been directed toward optimization of the agitator configuration for solids mixing and gas pumping from the atmosphere above the leach slurry. The rate of ferrous oxidation by molecular oxygen and the rate of zinc sulphide leaching by ferric ion have been studied over a wide range of temperature and solution compositions. The study of zinc sulphide leaching by ferric ion was supplemented by a series of interfacial tension measurements in the liquid sulphur - zinc sulphate solution system. The various kinetic studies have been summarized in terms of the importance of each rate to the performance of the process.

Jan 1, 1990

By Wolfgang Linden

The emerging demands on higher steel grades call for improvements in the operation of production units and a corresponding increase in automated processes, and therefore international steel producers require viable functions. The avoidance of slag carry-over to secondary metallurgy processes is essential for achieving steel grade qualities and reducing alloys in order to compensate slag residues in the downstream unit. The automatic tapping procedure in BOF converters will be supported by the implementation of reliable measurements used in high-end steel plants. Automatic tapping will help to achieve the following: Reduced slag carry-over, improved yield, increased reproducibility, improved working environment and safety and operation with minimum possible crew. The automatic tapping procedure is capable of being implemented in new or retrofitted installations.

Aug 17, 2017

By Nikolas K. Sokol

Underground construction often requires working within a very congested urban environment, including excavating shafts adjacent to highly sensitive and multistoried structures, sometimes even within such structures. Shafts adjacent to heavily loaded column footings are often required due to space constraints. Invariably, footing surcharges must be considered during the design of shaft rock reinforcement. Rockwedge stability evaluation reveals that column surcharges can greatly impact the ability to meet the desired factor of safety. Design methodologies and examples to deal with these special circumstances are presented.

Jan 1, 2008

By A. Broussaud

The paper describes the advanced grinding control system implemented at Newmont Ahafo gold mine, Ghana in 2009 and 2010. It shows how the different components of the Advanced Process Control (APC) system cooperate for increasing plant performance. The SABC circuit processes hard rock from different pits mixed with a variable proportion of oxides. The control strategy is designed to address specific disturbances, including start/stops of pebble crushers, unavailability of oxides, changes in rock size distribution resulting from segregation in the stockpile, and changes in ore type and hardness. The system consists of an expert system per se with extensive use of fuzzy logic, supplemented by an online dynamic model of the process used as a soft sensor, a VisioRock? rock size measurement system over SAG mill feed before addition of recycled pebbles, and an AudioMill? system to analyze the SAG mill sound and detect impacts on liners. All these components are embedded in the same OCS© software platform, which, among other benefits, makes it easy to support the entire system remotely. The paper details the physical constraints and the variables that are manipulated. It describes the control strategy and the contribution of each component of the system. It also describes the project implementation and the performance of the system. In addition to a strong involvement and support of management, the very good acceptance of the operators has been facilitated by the remote access system that made it possible to immediately modify the system each time it was needed during the baby sitting phase. The system made it possible to increase gold production significantly through increases in tonnage and recovery thanks to a better control of the grind size through a stabilization of the secondary ball milling circuit and an improvement of the operating conditions of the classifying cyclones.

Jan 1, 2012

By C. C. Merrill

Studies were made to determine the amenability of yttrium to fused-salt electrorefining in a controlled atmosphere. Tests were conducted in a LiCl- YCl3 electrolyte system at 710° C. The major variables studied were the YCl3 content of the electrolyte, from l.7 to 13.4 mol percent, and the initial cathode current density, from 410 to 1,630 amperes per square foot. Vacuum distillation was employed to remove salt from the deposited metal. Metallic impurities, except for lithium, could be reduced to near or below their lower analytical limits, ranging from 10 ppm for Cu to 300 ppm for Ta; reduction of oxygen content, however, was accomplished only in metal produced from electrolytes with 5.4 mol percent YCl3 or less. Initial cathode current density had little effect on the purity of the product.

Jan 1, 1967

By W. A. Padgham, H. Helmstaedt

Field evidence for current hypothe e about age and kinematic ignificance of gold-bearing hear zones in the Archean Yellowkni fe greenstone belt is reviewed , and it is concluded that major disagreements between previous workers are a direct result of differences in stratigraphic and tructural in terpretations of the Yellowknife Supergroup. Although goldbearing hear zone appear to be confined to the mafic volcanic pile of the Kam Group. it can be shown that shearing affected all supracru tal rocks, including the Jackson Lake Formation. now con idered to represent the youngest unit of the Yellowknife Supergroup. tructural ob ervations are incompatible with the hypothe is that the hear zones represent loci of ynvolcanic gravity sliding but are consistent with earlier conclu ions that shear zone development commenced with rotation of the volcanic pile and continued as re ult of lateral shortening broadly overlapping with the emplacement of granitoid batholiths. Shear Zones are common throughout the entire green tone belt. yet productive zone are confined to the Yellowknife Bay Formation of the Kam Group and localized where flow abut with a high angle again t the contact of the We tern Plutonic complex. However. no obvious tructural and lithological features have been recognized that are more favorable for gold deposition and distinguish the shear zones and flows of the area around the mines from those of other parts of the greenstone belt. The model that gold wa transported by metamorphic solutions and that hear zones were the firs t-order control for gold deposition provides no explanation for the trong localization of the depo it . As porphyries with elevated gold contents are present in and near ome of the mines. the possibility that gold was deposited from hydrothermal system around fel ic intrusion representing early phases of the Western Plutonic complex should be given erious consideration.

Jan 1, 1986