Search Documents

By Steve Kral

Reducing the cost per ton and increasing productivity are key factors in a mine’s profitability. Mining companies can do little about commodity prices. So to keep a mine operating at a profit, management must reduce costs and improve worker and equipment productivity in every facet of a mining operation. From mining to crushing to processing, mine management is constantly seeking new methods and technologies to improve the way it mines minerals. And it is willing to borrow techniques used by other operators.

Jan 1, 2002

By Vasilis Androulakis, Caroline Gerwig, Zach Agioutantis

Mining operations that involve caving of the overlying strata are designed so that caving occurs in a controlled manner by progressive overburden failure. However, there are many cases where the overlying strata bridge over the caved area for longer periods than anticipated and desired. As the caved area expands with the advance of the mining panel, excessive amounts of energy accumulate in the roof strata which will be rapidly released when the overburden eventually fails.

By M. Rafieazad, P. Fathi, M. Mohammadi, A. M. Nasiri

This study examines the impact of low-temperature heat-treatment cycles on microstructure and corrosion performance of Direct Metal Laser Sintered (DMLS) AlSi10Mg_200C alloy. It is known that the morphology and the size of eutectic silicon are the two most critical factors affecting mechanical properties of the AlSi10Mg alloy. Although high-temperature heat-treatment cycles are common practice for the strengthening of the cast Al-Si-Mg alloys, in the case of DMLS fabricated AlSi10Mg alloy, high-temperature solutionizing and low temperature annealing cycles result in mechanical properties degradation primarily due to a dramatic decrease in the solubility of Si in the super-saturated a-Al matrix of the as-printed alloy. In this study, low-temperature heat-treatment cycles that only promote precipitation of Mg2Si accompanied by the interruption of the silicon network were investigated. SEM and XRD analysis were utilized to observe the evolution of microstructure after different annealing heat-treatments at 200, 250, 300, and 350°C for 3 h. Increasing the heat-treatment temperature contributed to the Si networks interruption and an increased precipitation of Mg2Si phase. Low-temperature annealing from 200 to 350°C was found to promote the homogeneity of the microstructure characterized by a uniform distribution of eutectic Si in ??-Al matrix. Additionally, in order to investigate the impact of different heat-treatment cycles on corrosion resistivity of DMLS-AlSi10Mg_200C, the potentiodynamic polarization testing and electrochemical impedance spectroscopy were performed in a 3.5 wt.% NaCl solution. The results revealed more uniformly distributed pitting attack on the corroded surface by further increase in the annealing temperature, which was attributed to the uniformity of Si dispersion. In comparison, low temperature annealing at 200°C led to a penetrating selective corrosion attack along the melt pool boundaries, resulting in a higher corrosion rate associated with the lower absolute value of impedance of the protective passive film on the surface.

Jan 1, 2018

Vertical retreat open stoping (VROS) is a variation of sublevel open stoping (SLOS) that has been introduced at Cannington to minimise the influence of subvertical geological structures during stope extraction. The first application of VROS is described, where structures within the stope resulted in a change in firing sequence and the extraction of two complete sublevels in a single blast. The use of electronic detonators is critical to the success of VROS and their application is described. Numerous benefits of using VROS have been identified and are described. To date, eight stopes have been successfully mined using VROS. In addition to the first application of VROS, two further case studies are described.

Jan 1, 2005

Cessation of mining on the Bendigo goldfield makes it evident that, as the older generation fades away, knowledge of the famous Bendigo saddle reefs will be limited in the future by their written records. It is important therefore that the summarised account by D. E. Thomas (1953) in the Geology of Australian Ore Deposits should not be misleading. Fig. 6 in this article is stated to portray a cross section and longitudinal section through a series of gold shoots in the Garden Gully 300 ft. reef. The gold shoot along the capof the saddle reef is represented as extending down the east leg in a series of prongs, with the tips of the prongs about 50 ft. apart. It is the purpose of this note to indicate that this illustration can be suspected to be a diagram of the old stopes instead of a diagram of the distribution of gold in the quartz.The original sketches of Figs. 6 and 7 in Thomas' account were extracted, I believe, from the field note books of H. S. Whitelaw, years after his death in the late twenties. Whitelaw was stationed in the Bendigo office of the Geological Survey of Victoria, carrying out geological surveys of the Bendigo mines. He was there for many years before the Gold Research committee started its investigations in 1916 and he was acutely aware of the problem attached to the distribution of gold in the reefs. He had felt concern that manyauriferous reefs were being mined without adequate study and record and he decided, as he expressed it to me, to pick up what he could as he went along. There can be little doubt that the diagrams of Figs. 6 and 7 are products of this resolve.Opportunities to investigate gold occurrences at Bendigo were limited before 1916 because the field was operated by Manuscript received at The Institute 18th November, 1960.

Jan 1, 1961

By F. D. Cannon

"In metal and nonmetallic mineral mines during the 15-year period 1911 to 1925, 30.17 per cent of all fatalities and 16.57 per cent of all injuries were caused by falls of rock or ore from the back or roof or from the wail; 1.24 per cent of the fatalities and 11.05 per cent of the injuries were caused by rock or ore while loading at the working face; 6.66 per cent of the .fatalities and 2.49 per cent of the injuries resulted from men falling down 3 chute, winze, raise, or stope; and run of ore from chute or pocket caused 1.48 per cent of the fatalities and 1.93 per cent of the injuries.3 Hence, accidents due to falls of men and material caused. 39.55 per cent of the fatalities and 34.05 per cent of the injuries in these mines. Accident prevention can best be assisted by each company's preserving complete records of accidents classified according to cause and rate per thousand or 10,000 shifts. A systematic method of recording accidents and the employment of graphs or charts will be helpful to the company safety department in analyzing the cruses of accidents. The purpose of this publication is to analyze data on accidents caused by falls of men and material in metal -mines of the United States, and to suggest methods of preventing or reducing such accidents."

Jun 1, 1929

By Jizeng Zhao, Li Liu, Weiqing Chen, Jinxia Meng

This paper discusses the utilization of chromium slag, which presently has no useful application in China, as a resource. The following research has been done in this paper: (1) After determining the composition and properties of chro- miumresiduewedecidedtotesttheideaofusingchromiumslagasacomponentin synthetic MgAl O spinel material. (2) Through experiments on sintering and 2 4 electric melting of refractory materials we determined the best conditions for a practical process. (3) We compared the performance of the refractory material obtained with traditional spinel refractory materials and confirmed the excellent performance ofoursystem. The results show thefeasibilityofpreparing MgAl O 2 4 spinel material from chromium slag by electric melting. (cid:1) (cid:1)

Mar 1, 2018

By K. C. Dunham, M. Solomon, T. A. Rafter

Sulphur isotope ratios have been determined for 81 sulphides and S and O isotope ratios for 26 barites from the Alston Block in the northern Pennine ore field. In addition, both isotope ratios have been determined for 29 evaporitic anhydrites of various ages from European and Australian localities. The consistency of the sulphate isotope ratios over a wide area of the northern Pennines, and their similarity to values for Lower Carboniferous evaporites, suggests that the sulphate originated from Lower Carboniferous connate waters. It is suggested that these mingled with warm brines rising through granitic plutons beneath Tynehead and Upper Weardale, the aqueous sulphide ion in these brines having a delta34S value of approximately +10 per mille. The delta34S values for the sulphides range from +15.0 to -5.9 per mille and show an outward zoning with higher values in the central fluorite zones and mainly negative values in the outer barite zones. The wide range of delta34S values for the sulphide S is not characteristic of magmatic S and there is no adequate local source in the Carboniferous sediments. It is suggested that formation waters, probably mainly of connate origin, sank down sufficiently deep to become heated above 200°C before rising through Caledonian granite plutons into the Carboniferous sediments, where they spread laterally to mingle with cooler sulphatic connate water. The rising fluids were hypersaline brines carrying F, Ba, Pb, Zn, Cu and S. Temperatures of deposition calculated from galena-sphalerite isotope fractionation are similar to temperatures previously determined from fluid inclusion studies.

Dec 1, 1971

By Derek H. C. Wilton, David T. W. Evans

"Abstract - The Midas Pond gold prospect, central Newfoundland, is hosted by sheared and altered felsic and mafic pyroclastic rocks of the Tulks Hill volcanics, Victoria Lake Group, and has been trenched and tested by 19 diamond-drill holes. Gold values are sporadic, with the best diamond-drill intersection assaying 7.3 g/t over 0.9 m, and the highest grade channel sample containing 14.7 g/t over 1.15 m. Alteration and mineralization are confined to a 200 m wide brittle-ductile shear zone. This shear zone formed in response to regional D1 deformation, and the shear zone fabric parallels the regional S1 foliation. D2 deformation resulted in broad Z-shaped flexuring of the shear zone. The deformation was probably related to the ca. 396 Ma to 420 Ma Salinic Orogeny.Advanced argillic alteration and an extensive halo of Fe-carbonate and pyrite surround the gold mineralization. Alteration minerals include pyrophyllite, paragonite, quartz, plagioclase, chlorite, fluorite, Fe-carbonate, and pyrite. As such, the alteration seems to reflect combined epithermal (argillic) and mesothermal (carbonate) mineralizing environments. The argillic alteration and fluorite represent a regional hydrothermal effect on the felsic volcanic rocks; whereas, the Fe-carbonate and pyrite represent a mesothermal alteration associated with auriferous quartz veins. The Au, which is spatially associated with pyrite, occurs in three structurally-controlled vein sets. These veins are confined to the contact between a highly deformed breccia (the banded mafic tuff) and structurally overlying, altered felsic tuffaceous rocks. The vein sets include: V1 boudinage veins that parallel the shear-zone fabric (C-shear veins), and V2 and V3 extensional fracture veins which are controlled by an S2 fracture cleavage. V1 veins are the earliest and contain the lowest concentrations of Au. V2 and V3 veins are concentrated within the hinges of the D2 flexures.Pb isotope data for galena separates indicate that the Pb in the vein systems was probably of local derivation. Sulfur, C, and O isotope data for mineral separates are similar to data for typical mesothermal lode gold deposits. Fluid inclusion data suggest the presence of at least three hydrothermal fluid types in the region, viz., (1) an early saline fluid which produced the argillic alteration, (2) a CO2-bearing fluid directly related to the auriferous mineralization, and (3) H2O-NaCl fluids which flowed through the Midas Pond shear zone at a lateral distance from the zone of mineralization. The mineralizing fluids are interpreted to have been CO3 -2-rich types which originated through metamorphic dehydration and decarbonation of mixed island-arc and continental crustal rocks. Gold precipitation resulted from the reaction of these fluids with the Fe-rich breccia unit. Pre-existing and simultaneously crystallizing pyrite served as loci for Au precipitation."

Jan 1, 2000

By J. M. Goris

The U.S. Bureau of Mines, in a cooperative project with the University of Utah, Salt Lake City, UT, and Homestake Mining Co., Lead, SD, conducted in situ monitoring and numerical modeling of rock masses supported with cable bolts in two mechanized, cut-and-fill stopes and a shaft pillar at the Homestake Mine. Extensometers were used to measure rock displacement, while cable bolt strain gauges were installed to measure loads on both conventional and birdcage cable bolt supports. These instruments provided an assessment of rock mass behavior during mining as well as essential data for verifying results from computer analyses. The numerical modeling program FLAC was used to analyze cable bolt patterns and supports. Results from the evaluation study indicated that cable bolt strain gauges and extensometers were effective instruments for monitoring the behavior of rock masses supported with cable bolts. Also, numerical modeling of the 4S-48N stope using the FIAC code provided displacement values comparable with measurements from field extensometers.

Jan 1, 1993

By Mingfei He, Jianhua Chen, Yingchao Liu, Yuqiong Li

Pyrite is one of the most common sulfide minerals on earth, which is usually grown with chalcopyrite and other sulfide minerals. In flotation practice, pyrite from different mines or different sections in a same mine may have different flotation behaviors. This is because the pyrite crystal contains lattice defect, including ionic vacancy and lattice impurity. The present work investigates the effects of three typical 3d transition metal (Co, Ni, and Fe) on the adsorption of CH3OCS2 −, OH−, and CN− on pyrite surface by density functional theory (DFT) calculations. Calculated results show that Co impurity reduces the adsorption energies of CH3OCS2 − and CN− on the surface of pyrite, while Ni and Cu impurities significantly increase the adsorption energies of CH3OCS2 − and CN− on the surface of pyrite. Co impurity has small influence on the adsorption of OH−, but Ni and Cu impurities significantly increase the adsorption energies. Calculations on Mulliken charge population of Co2+, Ni2+, and Cu2+ indicate that the Mulliken charges of Co2+, Ni2+, and Cu2+ after OH− adsorption are more than those after CN− adsorption. This suggests that the ionic property of the M-OH- coordination bond is greater than that of M-CN- coordination bond, while covalent bonding of M-CN- coordination bond is greater than that of M-OH- coordination bond. The adsorption results are discussed based on coordination field theory (CFT).

Oct 6, 2020

By V. A. Mironenko

The combined study of ground water regime and rock deformations has resulted in the theoretical substantiation of the common principles for analysis of the hydrodynamic and geomechanical processes Within the scope of unique scientific direction -hydrogeomechanics (Mironenko and Shestakov, 1974). The hydrogeomechanical models are widely used now for the analysis and forecasting the extremely important processes connected with the safe and efficient mining operations, as well as with the protection of geological medium. Among these processes are: -deformations of the open-pit slopes and spoil dumps; -consolidation of rocks due to the ground-water pressure drop; -water-end-rock material inrush into mine workings caused by deformations of the undermined rock mass; -geodynamical processes due to the changes in ground water regime; -artificial hydrofracturing in rocks; -transformations of clay linings under the tailing ponds and other technical water basins.

Jan 1, 1990

By Kan Song, Lin Liu, Hengzhi Fu, Jun Zhang, Haijun Su, Xiaojiao Jia

"Al2O3/YAG/ZrO2 eutectic in situ composite has been regarded as new generation of high temperature structural material due to its excellent performance even close to its melting point. The directionally solidified Al2O3/YAG/ZrO2 eutectic ceramics are prepared by recently developed Laser Floating Zone Melting (LFZM) apparatus in which a splitter mirror is used to obtain two beams with the same quality from one CO2 laser. With the two laser beams irradiate the sample from opposite directions, the sample is zone melted. The apparatus configuration and the solidification processing are described in detail. The solid/liquid interface morphology is studied and the mechanism of microstructure formation especially the characteristic of eutectic cellular is discussed. It is shown that YAG and ZrO2 phases play a leading role during the ternary eutectic growth. Meanwhile, the relationship between the solidification microstructure and the processing parameters are investigated.IntroductionAl2O3/YAG/ZrO2 ternary eutectic in situ composite, due to its excellent high temperature mechanical properties, is now considered to be a promising candidate material as a replacement of nickel based super alloy for new generation aero space engine turbine blade [1]. They exhibit flexural strength of 360-500 MPa from room temperature to 2073K in air atmosphere [2]. The compression creep strength at 1873K is 433MPa with the strain rate of 104/s [3]. However, because of the high melting point and complex physical properties, there remain still many difficulties for its application. One of the bottlenecks is the poor understanding of the relationship between microstructure and solidification conditions."

Jan 1, 2012

By C. Han

The analytical results of Dagushan grinding workshop primary grinding operation product show that the size fraction of -0.079mm is 32.88%, the size fraction of -0.01mm is 9.97%, the rate of -0.01mm size fraction and -0.079mm size fraction is 30.32%. It means that there is too much -0.01mm size fraction in primary grinding operation product and fall out that there will not be a better result in following operations. Several tests have been carried out to control the size distributing of the primary grinding operation product according to confirm the appropriate conditions of grinding operation. Integrate with theoretic count, grinding property tests show that the appropriate rev ratio of ball mill should be between 85% and 90% so as to get better size distributing. Based on the results of grinding property tests, the shocking property tests simulated the momentum of different diameter steel balls in the ball mill have been carried out. It showed that if want to get better size distributing the appropriate diameter of steel ball should be 110mm. The tests result shows that regulate diameter of steel ball and rev ratio of ball mill could control the size distributing. Contrast to the technical parameters of ball mill in grinding operation now, there are some significant advices are given for practice and industrial tests.

Jan 1, 2014

By Richard P. Cislo

The evaluation of the effectiveness of the time domain Coal Interface Detector developed by the General Electric Company under contract H0155120 is the subject of this report. The sensor utilizes differences in the time characteristics of shearer vibrations as sensed by an accelerometer mounted on the ranging arm to discriminate the cutting of coal and rock. Pour identical time domain sensors were supplied by the Bureau for field evaluation. The performance of the time domain sensor was evaluated by an extensive field test and data collection program that included four longwall mines and a total of nine mine visits. The intent was to determine the sensor's applicability to a wide range of mining conditions and to document its limitations. Results of the extensive field tests indicate that shearer vibration data processed by GE's time domain signal processing algorithm cannot be used to reliably detect when the cutting drum crossed the coal/rock interface.

Jan 1, 1987

By John F. MacDonald

From 19BS thru the present, Guy F. Atkinson Construction Company has been involved in several transportation construction projects in the Seattle area. Two of these contracts, the Mt. Baker Ridge Tunnel, and The Seattle Bus Tunnel, had unique foundation features. MT. BAKER RIDGE TUNNEL ACCESS PITS The Mt. Baker Ridge Tunnel is part of the general upgrading of the I-90 freeway between I-405 and I-5 (see Fig. 1). It is located on the western shore of Lake Washington and consists of a 1300 foot long large diameter tunnel thru Mt. Baker Ridge. The ridge consists of over consolidated silts and clays overlain by a loose to medium dense silty fine sand. The water table is perched in this upper layer of material. The clays of Seattle have a history of being very sensitive to excavation. The hills are marginally stable and numerous landslides have occurred recently in the area of the tunnel. [ ]

Jan 1, 1990

By JOHN R. SUMAN

IT appears now that the conflict with the totalitarian states will be a long-drawn-out struggle. The course of this war up to now indicates that this may well be the first major conflict where man power has not been the vital and determining factor. Mechanized warfare has made it possible for relatively small, well-equipped groups to outmaneuver and defeat large armies which lack the necessary modern equipment. Under these circumstances, ultimate victory becomes a matter of resources and productive ability. The important question is not how many soldiers can he put into the field, but the volume and speed in producing the armaments essential to ensure a victory. The resources available to the opposing nations and the efficiency of their systems of enterprise and production will be primary factors in determining the ultimate outcome. Germany had a head start of eight years in the armament race, and it is not easy to overcome such an advantage overnight.

Jan 1, 1942

By Gennadiy M. Poletayev, Mikhail D. Starostenkov, Alexandra S. Starostenkova

"The process of the combustion synthesis was modeled by computer simulation using the molecular dynamics method. The set of the critical parameters regulating the velocity of the reaction was found from these computer experiments. It was established that the character of structure-energetical transformations at the combustion synthesis in the systems Ni-Al and TiAl depended on the type of boundaries used for the phases delimitation in the bimetal thin films.IntroductionProducing new materials and products, based on the combustion synthesis (CS), is the objective of scientific investigations as one of the most perspective one for industrial applications. But there are several problems connected with theory and experiment. It allows us to forecast the properties of materials. First of all, the main problems are stipulated by structure-energetical transformations taking place at high velocities of the reaction and at high temperatures. It prevents the analyzing of the transformation mechanisms in materials, taking place at microscopic, atomic levels in details.It is evident, that computer simulation allows to decide some problems and to approach to more exact theoretical presentation of structure-energetical reactions taking place at CS. It is known, that the most typical systems, where CS is observed, are bimetals Ni-Al and Ti-Al. The investigation of interphase boundary stability in the systems of Ni-Al and Ni-Fe was made by the method of molecular dynamics in [1]. The bimetal thin film was presented by the packing of atoms in the plane (111) of FCC lattice. It was found that the discrepancy in the sizes of atoms A and B of bimetal was compensated by the formation of 60° top dislocations, set against interphase boundary in the absence of point defects and free volume. The density of top dislocations was proportional to the factor of size discrepancy of atomic components of the bimetal. Diffusional reconstruction of the interphase boundary and areas, situated near it, was observed only at definite concentration of point defects - vacancies, inculcated in the structure of the bimetal at the definite temperature. The atoms of the bimetal component of less size penetrated in the area of the second component with higher velocity. The clusters of intermetallic germs began to form. It led to the growth of the system temperature and acceleration of the process of the diffusional reconstruction of thin film. The following transformations were found: top dislocations splitted into single ones, which climbed from interphase boundary into the zone of more plastic component; the formation of sub grain structures took place."

Jan 1, 2001

By A. Idegami, M. Imamura, S. Heguri, Y. Ozaki

"Nickel powder can be produced by the reduction of a nickel ammine complex solution by hydrogen at high temperature and pressure. To minimize the deposition of fine nickel on the surface of the reactor and other equipment, seed crystals are added to the initial solution to promote nucleation of the nickel powder. Such seed crystals catalyze the precipitation of the nickel particles on the surface of the seed and enhance grain growth. In this study, nickel nuclei were precipitated by the addition of a polymer to the nickel ammine complex solution, resulting in the production of nickel powder. Thus, we herein propose a model that explains the effect of the polymer in the precipitation of nickel nuclei.INTRODUCTIONNickel powder is commonly produced via a hydrometallurgical process from the hydrogen reduction of a solution containing a nickel ammine complex at high temperatures and pressures, and this process was commercialized in the 1950s by Sherritt Gordon (Sherritt International, Canada, Benson & Colvin,1973; The Staff, Research and Development Division, Sherritt Gordon Mines, Ltd., 1958).In the above transformation, upon the injection of hydrogen gas into the solution, nickel is reduced as outlined in Equation(1), ultimately resulting in the production of nickel powder.Ni(NH3)nSO4+ H2?Ni+ (NH4)2SO4+ (n-2)NH3(n:2–6)(1)In this process, seed crystals are added to the reactor to suppress the precipitation of fine nickel (scaling) and to enhance nickel reduction (Benson & Colvin, 1973; Mackiw, Lin & Kunda, 1957). More specifically, iron sulfate and a small amount of dispersant polymer are added, which leads to the formation of nuclei. Upon subsequent hydrogen reduction, the reduced nickel can then be deposited on the nuclei, allowing nickel particle growth to take place. However, this results in iron contamination in the final nickel product, and so the use of pure nickel as a seed crystal is desirable to produce high quality nickel powders."

Jan 1, 2017