Search Documents

By Batric Pesic

Gold dissolution with bromine was studied by using the rotating disc technique. Geobram TM 3400 was used as a source of bromine. The parameters studied were: rotating speed, Geobrom 3400 concentration, pH, temperature, sulfuric and hydrochloric acid concentration, and the concentration of various cations (copper, iron, zinc, aluminum, manganese, potassium and sodium) and anions (chloride, bromide, sulfate, nitrate, and iodide) According to the Levich plot and activation energy, gold dissolution was controlled by a chemical reaction rate. Copper, iron, and manganese in their highest oxidation states, aluminum, zinc, sodium and potassium did not have any effect on gold dissolution rate. The presence of manganous ion dramatically decreased the gold dissolution rate. Kinetic performance of bromine, in the form of Geobram TM 3400, was compared with performance of cyanide and thiourea.

Jan 1, 1990

By Rak-Jun Choi

Plasma-induced damage of InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) has been studied in terms of forward turn-on and reverse breakdown voltages, together with etch rate and surface morphology. The physical degradation of sidewall along with rough surface morphology of n-GaN caused by increased ion scattering induced the deterioration of the forward and reverse voltages. It was found that the turn-on voltage is sensitive to the surface roughness of the etched n-GaN and the breakdown voltage is strongly affected by the sidewall contamination. Annealing under nitrogen after the mesa etching improved the electrical properties of the InGaN/GaN MQW LEOs. Efficient blue light-emitting diodes (LEOs) were fabricated using InGaN/GaN triangular MQWs. The LEOs with triangular QWs showed a lower operation voltage and 2.4 times higher light output power than those with the rectangular MQW LEOs at 20 rnA and 20 "C. The intensity of electroluminescence (EL) at 20 mA was almost independent of ambient temperature in the triangular QW LEO, but decreased substantially in the rectangular one.

Jan 1, 2003

By Roderick I. L. Guthrie, Donghui Li, Mihaiela Isac, Luis Calzado

The HSBC is an ideal process for the production of BMG strips. The purpose of the present work was to investigate the casting of Ca-based, bulk amorphous strips. The possibility of casting three Ca-based alloys (60Ca-20Mg-20Al, 60Ca-15Mg-10Al-15Zn and 55Ca-15Mg-10Al-15Zn- 5Cu (at.%).) was investigated, using the HSBC simulator. Numerical simulation and mathematical modeling were used to predict temperature variations and cooling rates, under different interfacial gaseous atmospheres (helium and air) near the meniscus region. Given the critical cooling rates and glass temperatures needed to be reached for the vitrification of the respective alloys, this leads to predictions of the critical thicknesses possible with this novel casting process. To validate our predictions, these alloys were then prepared and cast onto the sand-blasted, solid copper substrate mould of the HSBC simulator. The possibility of producing Ca-based metallic glassy strips via the HSBC processes was confirmed, using optical microscopy, X-ray diffraction and Scanning Electron Microscopy, to characterize the glassy properties of the cast strips. It was found that the HSBC process would be able to provide sufficient cooling to form amorphous strips for the 60CA-15Mg-10Al-15Zn and 55Ca-15Mg- 10Al-15Zn-5Cu alloys, but not the 60Ca-20Mg-20Al alloy.

Jan 1, 2014

By G. Diáz

The PLACID process applied to the recycling of spent lead-acid batteries is being developed by an European Consortium within the Brite-Euram II programme. The status of the project entitled "Lead Recovery from Lead Oxide Secondaries" is described in this paper. The main laboratory and batch experimental results and the preliminary feasibility study are summarised. The description of the demonstration pilot plant and continuous campaigns programme for 1995 are also included. An interesting global approach is proposed, integrating the Placid process in the existing spent battery recycling pyrometallurgical facilities. This yields important improvements in the overall process. Grids would be easily treated by the conventional pyrometallurgical route, obtaining lead alloys,, while battery pastes, slags and fumes would be fed to the Placid process, obtaining pure electrolytic lead (>99.99 %), ideal for battery paste manufacturing. The implementation of the Placid process into the existing battery recycling pyrometallurgical facilities is analyzed from technical, environmental and economical viewpoints. Greater overall lead recovery, lower operating costs, reduced waste production, environmentally safer residues and much better lead product quality are the key advantages. The authors draw the following final conclusion : Integration of the Placid process with conventional pyrometallurgical treatment is a feasible and very attractive alternative route for spent lead-acid battery recycling.

Jan 1, 1995

By David E. Hardt

"One of the critical variables to be controlled during arc welding is the size or geometry of the weld pool. The measurement of pool geometry has become an increasingly important problem with the advance of welding automation and control, and this paper addresses that problem. The basic concept of pool size estimation via measurement of pool dynamics is presented. The theory underlying this concept is discussed and is followed by a review of the current work in this area. It is concluded that pool dynamics can be characterized by natural frequencies of oscillation, for stationary welds, and that these can be measured by appropriate signal processing performed on the arc voltage. However, it appears that only full penetration welds show a strong correlation between weld size and natural frequency. Also, the extension of these results to the realistic case of moving welds has yet to be considered in detail. Nonetheless, this method of in-process measurement for real-time weld process control is still quite attractive where applicable since it can be accomplished simply by modifying the arc current schedule and by signal processing of the arc voltage.INTRODUCTUIONThe study of welding process control has been dominated by research into methods of in processing sensing of the weld pool geometry. While it has been shown feasible to measure the topside pool geometry using video methods [1,2], the penetration or backside bead width have remained elusive quantities. This is particularly true if a topside sensor location is required.The concept of using weld pool motion as a pool geometry sensing method was proposed by Hardt et al. [3] and later demonstrated by Hardt and Zacksenhouse [5] and Richardson and Renwick [6]. The concept is based on the fluid dynamics of a pool constrained by a solid container and by significant surface tension forces (i.e. a small shallow pool, not a ""pond"" or ""lake""). Such a pool, if subjected to external forces, will exhibit a surface motion is a function of that force, the properties of the fluid, the surface tension, and the shape of the container. Thus, if this motion can be excited and measured, and the relationship to the pool geometry determined, a means of sensing pool shape will exist."

Jan 1, 1986

By Sergio T. Amancio-Filho

FricRiveting technique is an alternative new spot joining process developed for thermoplastic-lightweight alloy structures. In this technique a cylindrical metallic rivet is used to join one or more thermoplastic / metal components by means of plasticizing and deforming the tip of the rotating rivet through frictional heating. Advantages of this new technique are e.g. short joining cycles, minimal sample preparation, absence of environmental emissions and enhanced mechanical performance in comparison to base materials. Qualitative and quantitative synchrotron X-Ray microtomographic and light optical microscopic analysis of a case-study joint on aircraft materials polyetherimide and aluminum 2024 showed that joint strength is mainly dependent on aspect ratio of the rivet (geometrical dependence) and quality of joint, (microstructural dependence), whereby increasing aspect ratios and lowering the percentage of defects usually yield improved strength.

Jan 1, 2009

By S. J. Gerdemann

The U.S. Bureau of Mines is studying the kinetics of wet oxidation of sphalerite concen- trate (ZnS) as a possible process for a gravity-pressurized reactor (GPR). At tempera- tures in excess of 200' C, a sphalerite water slurry will react with 0, to form zinc sul- fate (ZnSO,). However, the pressure required to keep the water from boiling at these temperatures has kept this reaction from becoming a viable continuous process. The GPR can easily obtain the high pressures required for this reaction. The reaction rate is complicated by the solubility of 0, in water and the further oxidation of ZnSO, to insoluble zinc oxysulfate (Zn4(OH),S04.4H20). The effects of pressure, temperature, and particle size on the rate of reaction were investigated. Reaction rate was found to be limited by the amount of oxygen in solution. However, at 250" C and 1500 psia, over 90 pct of the zinc was solubilized in less than an hour. The conditions for maxi- mizing the Zn++ in solution, while minimizing oxysulfate formation, are discussed.

Jan 1, 1993

By G. A. Brooks

Increasing interfacial area through gas injection is one of the main methods for accelerating reaction between slag, metals, and gases in modern pyrometallurgical reactors. In slag-metal reactors, the generation of a large number of metal droplets into the slag phase through high gas velocity has a much larger effect on the overall kinetics compared to the enhanced mass transfer through mixing. Top blowing technology generates large interfacial areas (>300 m2/tonne) through high impingement gas velocity at short distances between the exit of the injection lance and the metal-slag interface. Phase separation may become a limit at the case of very high interfacial areas, though there is still only limited understanding of the trajectories of metal droplets in slag-metal-gas emulsions.

Jan 1, 2003

By G. A. Brooks

Increasing interfacial area through gas injection is one of the main methods for accelerating reaction between slag, metals, and gases in modern pyrometallurgical reactors. In slag-metal reactors, the generation of a large number of metal droplets into the slag phase through high gas velocity has a much larger effect on the overall kinetics compared to the enhanced mass transfer through mixing. Top blowing technology generates large interfacial areas (>300 m2/tonne) through high impingement gas velocity at short distances between the exit of the injection lance and the metal-slag interface. Phase separation may become a limit at the case of very high interfacial areas, though there is still only limited understanding of the trajectories of metal droplets in slag-metal-gas emulsions.

Jan 1, 2003

By Hiroyuki Matsuura

The effects of P2OS or Na2O addition on the reaction rate of CO2 dissociation on the surface of FexO-base molten oxides was investigated at I 773K by isotope exchange method 1-6. The rate constant decreased with increasing P2Os content of molten oxides and the residual rate constant was observed at high P2OS content. On the other hand, the rate constant increased with increasing Na20 content for FexO-SiO2 melts, The rate constant was evaluated by the composition of oxides and the rate controlling step of CO2 dissociation was discussed.

Jan 1, 2003

By Tetsuya Uda

Our recent achievements of rare earth separation technique[1,2] and new process idea for rare earth magnet recycling[3] are reviewed, (1) Binary chloride mixtures of rare earths were separated by a new selective reduction-vacuum distillation process. According to our experimental results, apparent separation factors were 8.1 for the Pr-Nd chloride mixture and 570 for the Nd-Sm chloride mixture. These values are much higher than conventional solvent extraction methods. (2) A study of recycling process of magnet sludge was carried out. The rare earths in the neodymium magnet sludge were extracted by chlorination with FeCI2, An activated carbon was used as a de-oxidation reagent Metallic iron in the sludge was not chlorinated because the iron monochloride is not stable, The extracted rare earth chlorides were easily separated from Fe-alloy and the excess of FeCh by vacuum distillation, 96 % of neodymium and 94 % of dysprosium in the sludge were extraeted into chloride phase, By the vacuum distillation, a mixture of neodymium and dysprosium trichlorides of 99.2 % purity was recovered, On the other hand, the rare earth chlorides can be converted to the corresponding oxides by a pyrohydrolysis reaction accompanied by a formation of HCl gas, The HCI gas can chlorinate metallic iron to FeCh, Therefore, a new recycling process for rare earth magnet waste can be realized as a chlorine circulation type process. During the process, only carbon and water are consumed and there are no toxic pollutants, Moreover, the obtained rare earth oxide can be directly used as raw material in the conventional oxide electrolysis process,

Jan 1, 2003

By A. K. Kyllo, G. G. Richards

"The formation and control of accretions is an important aspect of process operation for gas injection. The nature of the accretion formed can have a considerable effect on a process, especially on the life of the lance or the refractories in the tuyere region. There are three basic shapes of accretion formed on tuyeres; pipes, hemispheres and hollow-cored hemispheres. However, there are wide variations within these shapes. Generally, the type of accretion formed will depend on the injector design, certain operating parameters and the physical properties of the bath materials. This paper seeks to collect the results of previous and current physical and mathematical modelling together with data gathered from operating furnaces, to obtain a better understanding of the effects of process design and operating variables on accretion formation.IntroductionAn important consideration in the design of a gas injection process is the possible freezing of the bath either around the tuyere or on the lance. With proper design, freezing may be controlled to provide protection of the lance or refractory, and to avoid blockage. Improper design may lead to tuyere blockage and significant refractory or lance erosion. In view of this, a good understanding of the heat transfer in the injection region is essential.While tuyere blockage has been a persistent problem since the inception of submerged gas injection processes, the problem of accretion formation was not studied in detail until the development of the shrouded tuyere by Savard and Lee. A number of studies relating to accretion formation have been carried out since then, but there is still little information available relating the nature of the accretion formed to the design of the injection system.The build up of materials on lances is a similar problem, and may also be either beneficial or detrimental, depending on circumstances. Unfortunately, there is even less information available regarding build up on lances than there is relating to tuyere accretions. While the form of build up on lances is generally a simple coating of the lance, accretions on tuyeres tend to be more complex. Tuyere accretions tend to occur in one of three basic forms: pipe, hemispherical and hollow-cored hemispherical (Figure 1). However, there appears to be a considerable variation within these forms."

Jan 1, 1996

By J. W. Holzenthaler

Teams continue to play a major role at the Phelps Dodge Mining Company El Paso Operations, especially during the present time of low copper prices. The El Paso Operations' teams have taken the initiative during this copper market downturn and have helped reduce operating costs significantly. Because of this, Phelps Dodge El Paso Operations has continued to grow within the team process by creating a total, non- exempt salaried workforce. In the last year alone, the El Paso Operations have implemented three major initiatives to accommodate the team process. The first was the creation of "guiding principles", a policies and procedures handbook. Second was the "zero and beyond" safety initiative. Third was team compensation. In addition, the Copper Products Company has now adopted a work-team environment, following the lead of the refinery.

Jan 1, 1999

By Linfeng Zhou, Yuanbo Zhang, Rong Sun, Guanghui Li, Zhiwei Peng

The volatilization behavior of rhenium in the process of oxidative roasting of a molybdenite concentrate with 43.55 wt.% Mo and 321 g/t Re is explored based on identifying the relationship between volatilization of sulfur and rhenium. The results show that rhenium volatizes after sulfur and precise control of operating variables plays an important role in separating rhenium from molybdenite concentrate. When the roasting parameters are optimized as follows: roasting temperature 600 oC, roasting time 2 h, roasting atmosphere air, the volatilization rate of rhenium reaches 89.26%. In the process of solidification roasting, the volatilization rate of rhenium decreased almost to zero when the ratio of slaked lime/molybdenum concentrate was 10% excess to the stoichiometric requirement at 600 oC for 2 h.

Jan 1, 2016

By Roberto Parreiras Tavares, Frederico da Costa Fernandes, Guilherme Antonio Defendi, Vangleik Ferreira da Cruz, Júlio César de Sousa Pena

"Near-net-shape casting is an important area of research in the iron and steel industry today. Among the near-net-shape casting processes, the single-belt caster seems to be the most promising, since it is the only one that can achieve levels of productivity similar to those obtained with conventional continuous casting machines. One of the most important aspects in the single-belt casting is the feeding system used to deliver liquid metal over the belt. This system determines the velocity distribution and the levels of turbulence of the liquid metal and affects the quality of the strips. In the present work, a metal delivery system having a simple geometry was proposed. Using the CFD code CFX 5.6, a mathematical model to simulate three-dimensional turbulent fluid flow and heat transfer in that system has been developed. This model was used to analyze different configurations of the metal delivery system and the free surface shape of the fluid was also determined. A physical model of the feeding system was built and used to validate the predictions of the mathematical model. The fluid flow calculations have been validated by dye injection experiments and laser doppler anemometry. Measurements of the free surface levels have also been performed. These experiments provided supporting evidence for the predictions of the mathematical model.IntroductionTo maintain its competitiveness in the present market, the metallurgical sector, particularly the steelmaking companies, are developing new techniques of production. Some of these new processes are focussed on the strip casting technologies. Among these technologies, the SingleBelt process is considered the most interesting option, reducing the number of rolling steps and, consequently, the final cost of the product, especially the part associated to the energy consumption (fuel and/or electric energy). This process can also reach levels of productivity that can not be matched by other strip casting methods(1). One of the most important aspects concerning these new processes is related to the liquid metal delivery system. This system can have a significant effect on the final quality of the strips, since it determines the velocity distribution and the levels of turbulence of the liquid metal."

Jan 1, 2004

By Mao Chen, Tim Evans, Zhixing Zhao, Weidong Zhang, Baojun Zhao, Dongqing Wang

High temperature softening behaviours of iron blast furnace feeds (sinter, lump and pellet) have been determined under conditions simulated to the blast furnace. The industrial samples were packed with sandwich structure (coke / ore / coke) in graphite crucibles and 30 CO / 70 Ar gas mixture was blowing directly through the bottom of the crucibles. The displacement and temperature were continuously recorded simultaneously to construct the softening curves. Separated quenching experiments were also carried out at selected temperatures under the same gas atmosphere. The temperatures were selected corresponding to the turning points of the softening curves. The phase assemblages and composition of each phase in quenched samples were analysed by Electron Probe X-ray Microanalysis (EPMA). The proportion of the liquid formed at temperature was obtained from the backscattered electron images. The deformation characteristics of these complex multi-phase materials are shown to be related directly to the phase assemblages of the samples and the microstructures. FactSage was also used to assist the predictions of liquid / solid fractions and their compositions.

Jan 1, 2015

By Peng ZANG, Qihang Liu

Experimental work was conducted to determine the relationships of coal char conversion with temperature and heat absorption. The results show that at an earlier stage of the coke forming process, lump coal would absorb large amounts of heat but the increase of high temperature strength of lump coal was not significant. Contrarily, the lump coal’s high temperature strength was greatly improved at later stage of coke forming process. A number of residual coal was found in most tuyere coke samples illustrating that the lump coals added in the melter gasifier were not completely transformed into coke when they arrived at the tuyere region. The results indicate that the improvement of lump coal’s high temperature performance is limited in the melting gasifier by the low coke forming rate which could become the core factor of fines generation of lump coal in the melting gasifier.

Jan 1, 2016

By T. Wang, R. G. Reddy

"A new eutectic of LiNO3-NaNO3-KNO3 ternary system was calculated by using thermodynamic modeling and the eutectic temperature was predicted to be 389.15K. The melting point was determined using Differential Scanning Calorimetry (DSC). On repeated measurements, it was found that the melting point of the eutectic composition showed excellent reproducibility with the predicted value. The heat capacity was also measured using DSC and the data as function of temperature were fit to polynomial functions. Subsequently, the thermodynamic properties such as enthalpy, entropy and Gibbs energies of this novel ternary eutectic salt mixture were deduced as function of temperature.IntroductionIn these days, the provision of the large amount of energy required in the peak period relies more and more on the parabolic trough solar power plant and it works by utilizing the thermal transfer fluid. Consequently, the development of inoovative thermal transfer fluid with higher energy storage density is paramount to lower the expense for generating energy [1-4]."

Jan 1, 2013

By Rak-lun Choi

Plasma-induced damage of InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) has been studied in terms of forward turn-on and reverse breakdown voltages, together with etch rate and surface morphology. The physical degradation of sidewall along with rough surface morphology of n-GaN caused by increased ion scattering induced the deterioration of the forward and reverse voltages. It was found that the turn-on voltage is sensitive to the surface roughness of the etched n-GaN and the breakdown voltage is strongly affected by the sidewall contamination. Annealing under nitrogen after the mesa etching improved the electrical properties of the InGaN/GaN MQW LEDs. Efficient blue light-emitting diodes (LEDs) were fabricated using InGaN/GaN triangular MQWs. The LEDs with triangular QWs showed a lower operation voltage and 2.4 times higher light output power than those with the rectangular MQW LEDs at 20 mA and 20 °C. The intensity of electroluminescence (EL) at 20 mA was almost independent of ambient temperature in the triangular QW LED, but decreased substantially in the rectangular one.

Jan 1, 2003

By Christopher R. Casias

A basic methodology is presented (employing both standard and theoretical assessment, analysis. and data interpretation techniques) for classifying waste containing trace levels of radionuclldes. Despite increased regulatory requirements for handling. transporting. and disposing of such waste: (I) no formal characterization methodology has yet been Implemented. and (2) no limits have been set to define the point at which a waste material is considered to be low-level and below which it Is "below regulatory concern" (BRC) or can be considered to contain no more than a diminimus level of radioactivity (i.e . is nonradioactive). 'I1le concept of diminimus limits specific to waste streams and waste forms is introduced. and a mechanism fur evaluating waste In relation to BRC and diminimus limits is outlined. This methodology can be used to perform a complete and adequate characterization of waste for classification according to its level of radioactivity.

Jan 1, 1992