Search Documents

By Shekhar Bhansali, Shyam Aravamudhan

"This paper reports on the design and simulation results of a silicon bulk-micromachined diaphragm-type piezoresistive pressure sensor capable of operating linearly over a wide dynamic range (0-1000 meters of water). The piezoresistor elements of the sensor are arranged in a wheat stone bridge configuration to achieve a higher output response. Simulation results (output voltage and sensitivity analysis) obtained using coupled MemPZR-MemMech module of the CoventorWare2003 Finite Element tool are presented. The effect of diaphragm size, diaphragm thickness and thickness of the piezos on output sensitivity were analyzed and optimized to get a linear response over the wide dynamic range.IntroductionThe physical and biological processes in the ocean are critically influenced by ocean parameters (pressure, salinity and temperature). Thus there is a need to develop inexpensive and reliable sensors to continuously measure large volumes of sea-space over long time spans. A key component in any such system will be a pressure/depth sensor. This sensor is routinely employed in marine applications such as wave and tide gauges, tsunami detection, platform leveling etc. More significantly, pressure measurement is needed for depth determination. Depth sensors are vital for remote operated vehicles (ROVs), profiling instruments and towed arrays.Several techniques have been routinely used in the past to measure pressure in the marine environment [1-3]. In general, the pressure sensor design is based on a flexible membrane as the spring element for the sensing pressure [4]. The deflection of the membrane, induced by the applied pressure, is converted into an electrical output through a component that is sensitive to diaphragm deflection (capacitive coupling) or associated stresses (piezoresistors, strain gauges). The temperature compensated pressure measurement can be readily converted to depth using"

Jan 1, 2004

By Ming-Feng Ye, Jun Wang, Guang-liang Wu

In order to reduce the Al2O3 inclusions in 50Cr5MoV roller steel produced by EBT-LF-VD-VC process in a steelmaking plant, the LF refining slag was optimized and the influence of optimized slags with different w(CaO)/w(Al2O3) ratios on reducing inclusions were investigated in the laboratory. The results showed that, when w(CaO) = 50–55%, w(Al2O3) = 25–30% and w(CaO)/w(Al2O3) = 1.5–2.0, this optimized slag can not only reduce massive Al2O3 come from aluminium deoxidation, but also change the remain into plastic CaO-MgO-Al2O3 spherical compound inclusions with 1–5 lm diameter, the harm on the performance of the steel was minimized.

Mar 1, 2018

By Itsuki Uehara, Hiroyuki T. Takeshita, Tetsuo Sakai, Nobuhiro Kuriyama, Hideaki Tanaka

"AB5 type hydrogen storage alloys (A: rare earths, B: transition metals) are extensively applied to a negative electrode of a nickel metal hydride (Ni-MH) rechargeable battery for portable electric equipments, electric vehicles, hybrid vehicles etc. Performance of a hydrogen storage alloy electrode is affected by various factors, microstructure and surface composition of the alloy and structure of the electrode as well as composition of the alloy. Control of those factors enables us to commercialize the Ni-MH battery in various field.IntroductionA Nickel-metal hydride (Ni-MH) battery has been extensively developed because of (1) good compatibility with a nickel cadmium (Ni-Cd) battery, (2) high energy density (1.5-2 times higher per unit volume than a Ni-Cd battery) and high dischargeability, and (3) low environmental pollution. The charge/ discharge reactions can be written as [l, 2,3]:(+) Ni(OH)2+OH- = NiOOH+H2O+e· (E=+0.490V NHE),(-) l/6LaNi5+H2O+e-· = 1/6LaNi5H6+OH- (E=-0.828V NHE),where E° is a standard potential of an electrode vs. normal hydrogen electrode (NHE). Because of the above advantages of a Ni-MH battery, the battery have been widely used as a power source of portable computers, cellular phones, electric vehicles (Toyota ""LAV4L EV"", Honda ""EV Plus"" etc.) etc. Some hybride vehicles (Toyota ""Prius"" and Honda ""INSIGHT"") and fuel cell vhehicles (Toyota ""FCEV"") are power-assisted by a high-power Ni-MH battery. In 1999, the production of Ni-MH batteries reached 870 million cells in Japan. Most of commercialized NiMH batteries are incorporated with rare-earth-based AB5-type hydrogen storage alloy as a negative_ electrode. The production of rare-earth-based alloy is estimated to be approximately 8000 tons.The battery performances of the Ni-MH battery, for example, capacity, durability (cycle life), dischargeability (kinetics) and selfdischarge, ate closely related to the metal hydride· (MH) electrode, especially, the hydrogen storage alloy in the electrode. Substitution of alloy components, heat treatment, and surface treatment in order to change surface and bulk structure of hydrogen storage alloys have been examined by us and many reseachers in order to improve the performances of MH electrodes. This paper is a review of our and their efforts to improve performances of MH electrodes."

Jan 1, 2000

By Jared Ball, Darren Snashall, Paul Telford, Pengfu Tan, Ben Hogg

"The foamed converter charges were up to 3 8 per month in Xstrata Copper Smelter at Mount Isa. The issue of high converter foamover frequency had remained unsolved for many decades in Mount Isa. A thermodynamic model of copper P-S converter and a viscosity model of converter slag have been developed to simulate the slag blow and copper blow, in order to understand the mechanism of converter foamover. The model predicts the chemistry and viscosity of slag during slag blow and copper blow. The effects of oxygen potential, charge of dirty reverts, slag carryover, under-blowing, over-blowing, and temperature on the foamover and viscosity of slag in copper blow have been discussed. A theory has been developed to understand the mechanism of converter foamover. The practical solutions have also been developed and implemented in Mount Isa Copper Smelter. Some improvements of the industrial operations have been presented. After a series of improvements, the number of foamed charges per month in the converter operations has been decreased significantly from 35 in Aug 2008 to only one per month in 2009/2010.1. IntroductionThe Copper Smelter in Mount Isa receives the concentrate containing about 25% copper and produces anode copper that contains about 99% copper. There are several stages in the process. The first stage carries out in the ISASMELT™ furnace. The ISASMELT™ process produces a molten copper matte containing about 60% copper. An iron-silica slag and a sulfur dioxidebearing off-gas are the by-products of the process. The slag is taken to the slag dams for cooling before it is recycled through the Mount Isa Copper Concentrator.The matte is sent to Peirce-Smith converters. The converters further remove iron and sulphur to produce blister copper which contains about 97% copper. The anode furnaces remove any remaining sulphur and oxygen to produce anode copper that is about 99. 7% pure. This is cast into anodes and sent to the Xstrata Copper Refinery in Townsville for final refining.In the copper pyrometallurgical industrials, slag foaming is an important phenomena which occurs when the gas bubbles have stability and not rupture. Foaming greatly increases the interfacial area between matte, slag and gas and is essential for the operation of high intensity smelting processes. However, foaming or foamover is undesirable in P-S converter since it can damage the equipment and injure the operators. Figure 1 shows that the whole process of a foamover development in a converter."

Jan 1, 2011

By J. A. S. Tenorio, K. S. Barros, D. C. R. Espinosa

Considering the risks involving the use of cyanide, other complexing agents have been evaluated for the treatment by electrodialysis of the effluent of brass electrodeposition and among them, EDTA is interesting since it has been already tested for many years to separate ions. The main objective of the present paper was to evaluate the occurrence of fouling and scaling on the surface of the anion-exchange membrane HDX 200 by the construction of chronopotentiometric curves and speciation diagrams in different conditions (pH between 10–12 and proportion of cupric ions of 30%, 50%, 70%). According to the results, the chronopotentiometric curves did not show additional inflexion points typical for the cases which occurs fouling and scaling for the pH values evaluated, which is in accordance with the speciation diagrams of the solutions constructed with the aid of Hydra-Medusa software. Hence, the pH and the proportion of cupric ions did not show influence on the curves behavior.

Mar 1, 2018

By E. G. Noble

The potential for using heterotrophic microorganisms to solubilize manganese from low-grade domestic ores is being assessed at the Reno Research. center, U.S. Bureau of Mines. More than 90 pct of the manganese has been extracted from a variety of oxide ores in shake-flask tests using molasses as a source of .. nutrients for the microorganisms. It has also been demonstrated that high recoveries of manganese can be obtained from a domestic wad ore using column bioleaching. 'l'he isolation and identification of organisms responsible for manganese extraction is discussed, as are the mechanisms responsible for manganese solubilization.

Jan 1, 1991

Halide media are considered as suitable alternatives to cyanide for extracting gold and have received much attention lately. The extraction of gold by iodide-iodine mixture has been patented and briefly studied without much attention given to the fundamental aspects of this process. This paper reports recent studies on the kinetics of gold extraction in iodide media, using hypochlorite, iodine and hydrogen peroxide oxidants. The kinetics of dissolution was found to be dependent on the solution pH, reagent concentration and most importantly the iodide- oxidant molar ratio. Without proper control, the gold surface can be passivated due to the formation of solid products. Thermodynamic modelling was carried out to determine the equilibria governing the dissolution process. The formation of AuI solid was also identified as a possible product during the dissolution.

Jan 1, 1992

By Mariana M. Arantes, F. R. Valenzuela-Díaz, Olgun Guven, Vijay K. Rangari, Julyana Santana, Esperidiana Moura

Nowadays, the development of polymeric materials reinforced with residues of vegetal fibers is becoming popular for application in different segments, from the automotive to the civil construction and furniture industry. Vegetal fiber residues may be used as reinforcement of the recycled polymer materials, for instance, to produce foams to packaging or to thermal and acoustic isolation for green building application. This work is focused on the development and characterization of recycled-HDPE/EVA foam reinforced with fiber residues from babassu coconut epicarp. Firstly, composites based on recycled-HDPE/EVA blend reinforced with babassu coconut fiber were obtained by melting extrusion process. The composites were then extruded in a special single screw for foaming. The foam samples were submitted to mechanical tests, density measurement, DSC, TG, and FE-SEM analysis.

Mar 1, 2018

Proposed by outstanding electrochemist and electrometallurgist Prof. Raphael Agladze (191 1- 1989), process of copper and manganese co-electrowinning was enhanced to the pre- electrowinning stages: low,temperature co-leaching of copper and manganese containing materials, and to high-temperature co-roasting of the same materials with consecutive leaching. The report presents results of experimental investigations of the processes mentioned above, as well as results of thermodynamic investigations of co-roasting processes, and co- leaching processes computer modeling.

Jan 1, 1997

By I. M. Richardson, M. Janssen, I. J. Bennett, V. A. Popovich

The most critical processing step during the manufacture of screen-printed crystalline solar cells is firing aluminium and silver contacts, which generates residual stresses and solar cell bowing. In this paper, an alternative Ag contact formation mechanism is proposed and aspects related to electrical contact properties, residual stresses and layer delamination are investigated. It is found that there are two main processing parameters affecting the uniformity and delamination of the Ag/Si interface, namely the peak firing temperature and the silicon surface roughness. Silicon surface polishing gives a better wetting of the silicon surface by the glass layer, resulting in a good contact and lower incidence of large voids, compared to the case of highly textured surfaces. The non-uniformity in the glass layer and large voids at the Ag/Si interface (in the case of a textured surface) are expected to have a negative effect on the mechanical strength of the solar cell.

Jan 1, 2015

By Rodríguez M. Esperanza

The efficient performance of Pachuca tanks is strongly linked to the suspension of mineral particles, which results from the motion of the liquid caused by injected gas rising, in general, through a central draft tube. This study reports a computational investigation on the effect of operating and design parameters on the suspension of particles. By extending the classical 2-phase drift-flux model to compute the gas hold-up, the three-phase (water-air-particles) system was simulated as consisting of a variable-density liquid plus the solid particles. These two phases were treated as interpenetrated continua using an Eulerian approach to set a turbulent recirculating flow model in 2-D and transient state. The model predicted adequately the measured critical superficial air velocity, uc, needed for maintaining particle suspensions, in pulps with 10-50 wt% solids. Additionally, the model was used to investigate the operation of industrial size reactors, obtaining results that agree well with the general trends reported in the literature, and highlighting important differences with respect to laboratory-scale reactors.

Jan 1, 2009

By Binxu Zeng, Mark Jolly, Xiaojun Dai

"The traditional investment casting foundries use batch melting and chunky running systems to produce casting components. This method leaves the energy saving issue as subsidiary one. In our research project, one of the partners, the AEROMET international PLC provides the thin wall aluminium component ""filter housing"" for test. The AERO MET uses traditional casting route to produce the filter housing, which only gives 5% --10% yield. In this paper, numerical simulation method is used to analyse filling and solidification of the casting running system. The CRIMSON running system of the filter housing is designed by using casting simulation software, MAGMAS and Flow3D. By working with AEROMET, various configurations of the casting running systems were tested and analysed. Using them ultiple life cycle approach, the energy content of new process is compared with traditional one. It indicates that the CRIMSON process only uses 36% of energy consumed by the traditional route.IntroductionThe investrnent casting is a metal for ming process using expendable patterns, which is a standard casting technique and is widely used to produce quality parts. Its accuracy, versatility and integrity tie itself to important and precious engineering components in Aerospace industry. However, traditional investrnent casting process usually uses chunky runner system and gravity filling method. It not only reduces the casting yield of the product but also causes the pouring defect during the casting. As author's previous research showed that gravity filling method pouring basin and down sprue are two main resources of entraimnent defects generation. No matter how good the running system is, entraimnent defects such as double oxide films (DOF) and bubbles will I get into the casting to cause problem."

Jan 1, 2013

By Pamela Bogust, York R. Smith

Photovoltaic (PV) modules are becoming an ever increasingly larger part of our energy portfolio. As more and more PV modules are installed and come on-line, management of end-of-life (EOL) modules becomes an important issue. Currently, management of overburden EOL PV modules is not an issue, but is anticipated to be by 2030. Recovery and recycling of valuable metals in PV modules presents several environmental and economic advantages. In this brief review, we will describe processes for refurbishing and recycling of PV silicon. These processes involve some combination of mechanical, thermal, and chemical processing, all of which all have their oPV) modules have become wn respective challenges. Also, projections of PV module material streams are also highlighted.

Mar 1, 2018

By Kazuteru Tozawa

Surface tension, density and viscosity coefficient of acidic copper sulfate solutions simulating electrolyte solution for electrolytic production of copper have been measured and are summarized as a function of the solution composition and temperature. Nickel sulfatc is taken to be a representative coexisting sulfate that affects the physical properties of the copper sulfate electrolyte solution. The sulfates in the solutions, including sulfuric acid, increase the physical properties under consideration. Gelatin, representing organic additives for electrolyte solution, was found to sensitively affect the surface tension of the solution at low concentration of up to 200mgIL. The surface tension was markedly lowered by the addition of gelatin and the increasing concentration of gelatin led to a more pronounced decrease in the observed values. The surface tension gradually increases with time after addition of gelatin and the increase is enhanced by higher acid concentration and higher temperature. The observed change in the surface tension is considered to reflect the preferential adsorption of gelatin to the bubble-solution interface and the decomposition of gelatin due to hydrolysis to form various molecules having smaller molecular weights.

Jan 1, 2003

By D. Donald Downey

Pilot Testing Ion Exchange Resin (IEX) can go from very simple beaker testing to complicated column testing. Space velocities, regenerant quantities, loading capacities, ion leakage, are all terms that get accumulated together to prove or disprove a resin’s (or resins’) ability to load a single ion (or specific set of ions). Not getting all the resin’s operating parameters correct will disqualify (or at least skew) the results. Laboratory tests for capacity, moisture content, bead size, metals fouling, etc.—what does it all mean? At last count, there were over twenty-five separate ion exchange resin tests (analyses) that were available to end users. Standard testing procedures identify the resin properties but more specific procedures can be used to identify problems with equipment operation. Then, there are the costs to consider; simple cation resin testing (moisture content, total capacity and bead integrity) is in the $200/sample range. However, add to this Chatillon, Russian Ball Mill Test, HIAC particle size, metals and % regeneration test procedures and the lab work can increase to over $1000/sample. In this paper, the author will explain the “must-do” pilot and test procedures and why they are important and the key to understanding how resin performs ion exchange.

By Shu-cai Zhou

"To understand the solidification behavior of austenitic heat-resistant stainless steel (TP34 7) in rotary electromagnetic-field, the influence of electromagnetic stirring in mold (M-EMS) on solidification structure of TP34 7 heat resistant steel in a round billet continuous casting was investigated based on industrial experiments. The results indicate that the excellent billet solidification structure of TP34 7 heat resistant steel can be obtained with appropriate electromagnetic stirring parameters. The solidification structure of TP34 7 heat resistant steel can be remarkably refmed, central porosity and shrinkage cavity can be remarkably decreased and equiaxed grains zone widens was enlarged. The industrial trials verify that the stirring intensity of TP34 7 heat resistant austenitic stainless steel should be higher comparing with plain carbon steel. Due to a higher viscosity, rotating speed of molten stainless steel was 20-30% lower than that of molten carbon steel in the same magnetic flux density.IntroductionIn recent years, the development of ultra super critical (USC) plants is accelerated by the demands of environment protection and energy saving, and USC plants with steam temperature and pressure conditions in excess of 593°C and 24.lMPa respectively were constructed. To achieve the goal, it is important to develop new materials with excellent high temperature strength, superior resistance to oxidation and corrosion at high temperature. Besides, their cost must be low enough to meet the requirement of plants [ 1]. TP34 7H steel is promising austenitic heat-resistant steel, which is used as superheater/reheater tube material and is extensively used for high temperature components and fossil-fired power plants, and suitable to be used in USC boilers plant. This kind steel contains with about 0. 7%Nb and it keeps higher allowable stress and creep rupture strength than TP304 and TP321H [1-2]. TP347H has conventionally been produced by ingot casting followed by forging and rolling. Recently, in order to decrease the production cost, challenging trials to produce these types of alloys by a continuous casting (CC) process have been attempted. However, the solidification structure of austenitic stainless steel is one of the key issues that attract more attention. Due to the low thermal conductivity of TP347H heat resistant stainless steel (much smaller than that of plain carbon steel), pronounced defects during continuous casting of austenitic heat-resistant steel such as coarse columnar, center porosity and coarse bridging, greatly influence mechanical properties of fmished products.A widely used technique in metallurgy is the inductive drive of molten metals using rotational or traveling magnetic fields. Recently, rotary electromagnetic stirring (EMS) has been applied to reducing various defects and improving increase the solidification structure of the metals in the continuous casting of steel, Al-based alloys and Mg-based alloys [3-8]. Electromagnetic stirring of plain carbon and low alloy steel in the continuous casting bloom and slab is well established for improving the quality of cast products [9-11] and is widely used in industry. However, very few literatures on electromagnetic casting of heat resistant stainless steel have reported. In this work, an industrial plant trial was performed to clarify the effect ofM-EMS on the macroscopic quality ofTP347heat resistant steel billet, in which the regularity and mechanism of the influence of EMS on solidification casting billet were discussed."

Jan 1, 2014

By N. El-Kaddah, A. D. Patel, T. T. Natarajan

The phenomenon of particle migration in a conducting fluid under an applied electromagnetic force field finds its application in selective sorting of minerals and more recently in the removal of inclusion from molten metal. This paper deals with the analysis of the expulsion force and the flow around a spherical particle in crossed uniform electric and magnetic fields in .infinite and in confined medium. Analytical solutions will be presented for the electrk and magnetic fields as well as the induced flow at the limit of zero Hartmann number. The flow around the particle was investigated numerically at low and high values of Hartmann number. It will be shown the magnetic field has almost no effect on the velocity field when Hartmann number is less than 1.0. At higher Hartmann numbers the damping effect of the magnetic field was pronounced in the direction of the applied current. It is concluded that Hartmann number has little effect on the net force on the sphere particle.

Jan 1, 1999

By Harrison Hodge

In the Bayer process for alumina production, between 2–35% Al2O3 is lost with bauxite residue due primarily to incomplete dissolution of aluminiumbearing minerals during caustic leaching or the precipitation of sodium alumino-silicate solids. The recovery of sodium and aluminium from the residue, and particularly from the contained sodium alumino-silicates, is becoming an increasingly critical issue from both an environmental and economic standpoint. Lime-soda residue sintering followed by selective leaching has been proposed as a method to recover sodium and alumina. The factors influencing the sintering mechanisms and kinetics, and the subsequent leaching have not been well described to date. In this study, the physical and chemical changes taking place during isothermal sintering of bauxite residue in air, particularly at short reaction times are investigated using scanning electron microscope (SEM) and X-ray diffraction (XRD). The impacts of these changes on the recovery of valuable materials are reported.

By Zhiqiang Zhou, Libin Zhu, Zizong Zhu, Hao Xiong, Yuchuan Ding

In order to utilize the lean ore resources from XinJiang rationally and optimize mixture, laborarory measurements have been carried out under different basicity, various mixed carbon content as well as the properties (ratio) of fuel particle size by the sintering pot for further microstructure analyses. The results show that sinter strength falls by 5.0%, low temperature reduction disintegration index (RDI) drops off to the lowest in certain ranges. The natural degradation index of sinter is much higher when sinter basicity is between 1.65 and 1.75. The sinter strength increases when sinter basicity is between 1.75 and 2.0. Meanwhile, the sinter strength and RDI +3.15 improve with increasing carbon content. And the sinter strength and RDI+3.15 both decrease with the decrease of the distribution ratio of small fuel particle, thereby decreases the yield of sinter. Microstructural analyses have been investigated to figure out the mechanism of the influence of the three factors on sinter.

Mar 1, 2017

By Wenjun Duan, Zongliang Zuo, Qingbo Yu, Qin Qin, Junxiang Liu

Moving bed has been widely used in the field of heat and mass transfer and reaction between solid particles and gas. In order to enhance the heat exchange coefficient, there will be tube banks inserted in the moving bed. In the process of drying ammoniates particles or heat recovery from high-temperature particles with moving bed, the particles flow behavior around the tube banks is significant. In this paper, the particles flow behavior around the tube banks is investigated, and all the results can provide guidance for the design and operation of a moving bed.

Jan 1, 2016