Search Documents

By Torben L. Edens

Norddeutsche Affinerie is the largest copper producer in Europe. Two sites are in operation for the production of refined copper: primary copper production is located in Hamburg and secondary copper production in Lünen. A total of just under 560,000 tonnes of copper cathodes is produced annually at the two sites. Primary copper production using the flash smelter furnace has been in operation in Hamburg since 1972. Over the years, the capacity of the flash smelter has been increased in three expansion projects from 120,000 t to almost 500,000 t of anode copper p.a. The anode sector consisting of two anode furnaces and a 24 mould casting wheel still features just about the same equipment as in 1972. The paper describes the most important steps taken to optimise operation which have put NA in a position to cast meanwhile more than 500,000 t of anode copper annually with the two anode furnaces and 24 mould anode casting wheel.

Jan 1, 2006

By Norbert L. Piret

During smelting of copper, arsenic in the feed reports to a large extent to the gas phase and some enters the anode copper. From the gas phase it is transferred during wet gas cleaning directly, or indirectly after dust processing, to aqueous solution. During the electrorefining and anode slimes processing, the anode arsenic content is also transferred to aqueous solution. Technology for the efficient removal of arsenic from process streams and cleaning of aqueous effluents is well established. However, the arsenic-bearing products, which thereby are generated, can vary widely in consistency, quality and quantity, from large amounts of gypsum contaminated with water-soluble arsenic compounds to residues with high arsenic content ' or arsenic products. Arsenic management in a copper smelter not only is involved with the duty of compliance to the gaseous and aqueous emissions standards but also should have as objective the minimization of the generation of arsenic-bearing and, in general, heavy metal-bearing solid waste. The present paper outlines options and the associated economic aspects for minimization of arsenic-bearing solid waste generation, for improvement of the environmental compatibility of the residues to be deposited and for the .production of commerciable arsenic compounds under appropriate market conditions.

Jan 1, 1999

By Osvaldo A. Bascur

Several new hydrometallurgical plants have been built in the past years. They have implemented new processes to treat new type of ores. New technologies have been used to improve metallurgical performance from the start. The cycle times between knowledge generation and innovation are often neglected in the traditional capital expenditures and building of these new process plants. The paper reviews several implementations in which they have started with new ways of using information management from the beginning. The implementation of a real time performance management infrastructure is reviewed to assist in the implementation of mine to product strategies, metallurgical mass balances, solvent extraction composition statistical process control, methods to minimize organic losses, reduce variable costs and to improve metal extraction. Several examples are provided to improve operations by simplifying the access and analysis of information from assets and metallurgical processes. Continuous improvement and innovations have been enabled to minimize start times and for faster troubleshooting and resolution of operational problems.

Jan 1, 2006

By Lucas Lopes da Costa

Bamboo fibers were characterized in terms of diameter distribution and tensile properties. Polyester matrix composites reinforced with these fibers were investigated for their flexural mechanical behavior. Specimens with up to 30% in volume of continuous and aligned bamboo fiber composites were bend-tested until fracture. The results showed an improvement in the composite strength and stiffness with the amount of bamboo fiber. A microstructure analysis by scanning electron microscopy revealed a reasonable adhesion between the fiber and the polyester matrix which justifies the improved mechanical properties of the composites.

Jan 1, 2010

By Cevat Serdar Kucukkaragoz

The kinetics of prereduction of Chromite by carbon was studied under argon atmosphere at temperatures between 1000°C and 1300°C . The compacted and agglomerated specimens were reacted by using a TGA system. The mixing characteristics and the degree of compaction of the chromite and coke particles were the main parameters influencing the reduction kinetics. The reduction rate increased with temperature reaching to 81% reduction at 1300°C. The metallization started as the metallic nucleation around the particles which was first observed at 1100°C. The particles were surrounded by the metallic phase at approximately 40 % reduction obtained at 1200°C. At 1300°C, the reduction proceeded with a high rate during initial stages and with a low rate at final stages. The reduction was found to proceed in the sequence of Fe3+to Fe2+, Fe2+ to Fe(metal) and Cr3+to Cr(metal) with the formation of carbides.

Jan 1, 2006

By Leonard J. Friedman

The contact process for the production of sulfuric acid has been used commercially since before the turn of the century (1880?s), and rapidly replaced the chamber process after the development of vanadium catalysts in the early 1900's (1910's - 1920's). Plant size has increased from a few tons per week to single train units in excess of 4,000 tons per day. Much of the history of the contact process is in the minds of the few remaining early process pioneers that started in the industry in the 1920's and 1930?s, and in sulfuric acid industry books published in 1921, 1925, 1936, and the last Deucker and West in 1959. Since those not familiar with history are doomed to repeat the failures and mistakes of the past, this paper includes a brief history of the contact process along with the history and development of equipment and materials in each equipment area of the process. The main focus of the paper is to present the development and analysis of equipment and materials in the contact section of the sulfuric acid plant - from the dry tower to stack.

Jan 1, 1999

By K. S. Jeong

Since the start-up of the Onsan Smelter in 1979, LS-Nikko Copper has grown into a competitive smelter through continuous development. Several environmental improvements have been carried out, in particular, intensive investments in reducing SOx emissions, such as de-sulfurization plants, fugitive gas capturing and TMS(Tele Metering System). In addition, in recent years LS-Nikko Copper has spent more than 10 million USD every year to improve environmental conditions. In order to be a global leading smelter in every aspect especially environmentally, LS-Nikko Copper plans to inspire environment-friendly minds, co-operate with shareholders, and participate in global conventions. This paper describes the environment improvements carried out at Onsan and briefly introduces a sustainable vision for a green smelter.

Jan 1, 2006

By R. A. Cockerell

This paper is concerned with the application of Advanced Process Control (APC) to copper smelting processes. A number of key issues relating to the application of APC, such as modelling for control, process dynamics and time delays, instrumentation and sampling, are discussed. A general methodology for the application of APC is then presented. Finally, three case studies are presented to demonstrate the benefits and efficacy of applying APC.

Jan 1, 1999

By B. Yalamanchili

Gerdau Ameristeel Beaumont presents its systematic approach for upgrade decisions that has developed over 30 years of ongoing capital projects for quality and cost improvements. This system serves to identify product needs, select process improvement strategies, justify them, and assist multi-department communications and decision-making. This is illustrated with Beaumont mills? last Stelmor upgrade and leads to a discussion of the need to consider Life Cycles of both products and technologies as we move to answer the challenges of the future.

Jan 1, 2006

By Guray Kaya

Boron minerals are widely employed in various fields such as ceramic, glass, cement, metallurgy, etc. Although boron deposits of the world are limited, the production level of boron-based products is continuously increased. Turkiye possesses approximately 73 % of total world boron resources. Etibor Kirka Borax Company of Turkiye produces tincal concentrates and borax pentahydrates. During such productions considerable amounts of concentration and derivation wastes appear. Having considered the increased rate of production it is quite obvious that the level of relevant wastes will also be raised. With this study it was aimed to utilize these wastes in roof tile and brick bodies and to convert them into a form environmentally and human friendly. Newly produced products were undergone to several standard tests for the determination of their shrinkage, water absorption, strength values and coloring parameters. Additionally, micro structural studies were conducted.

Jan 1, 2006

By L. N. Ertzeva

The present work is dedicated to investigation of the sulfidizing process of ore pyrrhotite concentrate with recovery of a sulfide material, enriched with non-ferrous metals, and waste pyrite, with downstream separation by a certain beneficiation method.

Jan 1, 2006

By K. L. Hardee

A recent development has emerged which produces a retrofittable, low cost anode by attaching disposable, electrocatalytically active titanium mesh over the existing lead anodes. The coated titanium mesh anode operates at potentials of several hundred millivolts lower than the lead anode, providing significant power savings. The exposed lead surfaces are stabilized since most of the current flows through the titanium mesh. With the minimal lead corrosion, the sludge formation is virtually eliminated and the purity of the plated copper is greatly enhanced. Further savings may be realized by the elimination of non-essential chemicals such as cobalt. Since the combination anode is stable and uniform, the plated copper is also more uniform with minimal formation of dendrites, reducing the shorting. Full-size anodes have been tested for over 6 months in commercial copper electrowinning cells. The laboratory and field performance of the stabilized lead anode will be reviewed, including the voltage characteristics, the lead stability and the copper cathode purity.

Jan 1, 1999

By M. Sahoo

The development of new alloys containing bismuth and selenium for potable water supplies are reviewed. The new alloys are replacements for the leaded red- and semi-red brasses by the low-lead alloys, SeBiLOYS I and II, for sand casting, and SeBiLOY III replaces the lead containing yellow brass, C85800, for permanent mold casting. As the new alloys use bismuth and selenium, the supply and demand of these elements are discussed. The key casting characteristics discussed are: tendency to dross formation, freezing range (liquidus and solidus temperatures), fluidity, resistance to hot tearing, microstructures, mechanical properties, machinability, grain refinement and corrosion behaviour.

Jan 1, 1999

Bath smelting options for recovering valuable metals from jarositic residues containing 22-28% lead and 16-30% sulphur obtained from pressure leaching zinc-lead-copper bulk concentrates were investigated using thermochemical computations and crucible-scale experiments. Direct fuming of lead and zinc from a slaglmatte bath at 1250-300°C was demonstrated successfully. Up to 93% of the lead was recovered in the fume and steady-state recoveries of zinc were predicted in the range 82-95% under these conditions. The energy required for the fuming reactions was supplied by partial combustion of the fuel, added as char, with air. An important feature of the process is that the recoveries to the fume are not significantly affected by changing: the fuel:air ratio over a wide range. Thermodynamic computations, confirmed by experimental results also showed that the presence of a matte phase is not essential for high recovery of lead and zinc to the fume. Operating conditions which produced a matte ensured that about 70% of the silver and 80-90% of the copper were recovered into that phase. Approximately 98% of the arsenic in the residue was fumed. In the absence of matte the slags contained high arsenic levels (260-330 ppm) but low arsenic (20-60 ppm) levels were achieved when matte was produced.

Jan 1, 1994

By J. A. Jensen

In-situ composites were produced in both Ti matrix (Ti-20Y) and Mg matrix (Mg-20Ti, Mg- 20Nb, Mg-20Fe, and Mg-8Li) alloys. In Ti-20Y, a < 1010 > fiber texture formed in both the Ti and Y phases, and UTS increased from 240 MPa, (as-cast) to 950 MPa after deformation processing to a true strain of 7.3. Deformation processing produced smaller UTS increases in the Mg-matrix composites, but they showed exceptional resistance to weakening from exposure to elevated temperatures. The Mg-20Fe, Mg-20Nb. and Mg-20Ti composites tolerated 6-hour exposure to 400°C with no reduction in their 250 to 300 MPa room temperature UTS. All composites studied had excellent ductility and machinability.

Jan 1, 1995

By A. R. Laplante

Recent developments in gold metallurgy are used to illustrate how the interface between gravity recovery and hydrometallurgy has evolved in recent years. Of particular interest is the use of gravity recovery to produce high-grade concentrates that can be subjected to intensive cyanidation. It is expected that a growing proportion of gold production, possibly close to 50% in certain countries, will follow this route. Other examples of the interaction between gravity recovery and cyanidation are also provided. Implications for new and renewed research directions are discussed.

Jan 1, 2003

By Lars O. Werme

Already the KBS Project proposed copper as a suitable material for encapsulation of spent nuclear fuel. The basis for this choice was the thermodynamic stability of copper in water and the fact that deep granitic groundwaters in Sweden are oxygen free. With a limited supply of oxidants, a copper canister would have the potential for a very long service life. The research and development work aiming at encapsulating nuclear fuel entered a new phase in 1993, when SKB launched its Encapsulation Plant Project. Within this project, SKB has: ? designed a facility for encapsulation of nuclear fuel, ? laid down the design premises for a canister for disposal of nuclear fuel, ? tested and developed fabrication methods for copper canisters, ? evaluated the long term chemical and mechanical behavior of the canister, ? made preliminary plans for a factory for the production of copper canister, ? constructed a canister laboratory for full scale testing of the key operations in an encapsulation plant. The conclusions of this project were that a canister consisting of an outer layer (50 mm) of copper over an insert of cast nodular iron would provide sufficient corrosion protection and would have sufficient mechanical strength. This canister can be produced by several methods of which forming from rolled plates, hot extrusion, and "pierce and draw" have been tested at full scale. The canister will be sealed by electron beam welding in the encapsulation plant, and the integrity of the weld will be verified by ultrasonic testing and&apos; high-energy radiography. The final development work in this area will be performed in the canister laboratory.

Jan 1, 1999

By Sung-Joo Lee, Gi-Chon Han, Nam-Il Um, Hee-Chan Cho

"In Korea, almost all of bottom ash produced by coal power plants is disposed of in ash ponds. Ash storage areas comprise more than 80% of most coal power plant sites. This disposal method is causing environmental problems and a managerial burden for plant operators. In this study, investigations to develop a beneficiation process for separating coal pond ash into various products were undertaken. To improve efficiency of the separation, coal ash was separated by sizes and each size fraction was subject to various beneficiation processes. The separation process used were flotation (-200 mesh size), hindered settling (16x200) and tabling (16x200 and 8x16 mesh). The results showed that various marketable products, such as lightweight aggregate, sand, high-carbon fuel, could be recovered from coal pond ash using simple physical separation techniques.IntroductionDue to the increased use of coals every year, about fifty million ton of coals were used in 2007 alone. As a result, about 6 million tons of coal ash were generated. In Korea, the coal bottom ash is classified as a general industrial waste and is usually disposed of in ash ponds. The costs for this disposal method continue to increase due to rising costs of site management and development and more strict environmental regulation. Therefore, utilities are constantly looking for ways to increase utilization of coal ash. In this study, various beneficiation processes were evaluated to examine the possibility of separating coal pond ash into various products which can be used as aggregates and high-carbon fuel."

Jan 1, 2008

By Pinakin Chaubal

An analysis of the blast furnace and the low-pressure shaft DR furnace is carried out by redefining the reaction zones. The concept of a characteristic reaction gas temperature (CRGT) is introduced and the two reactors are compared and contrasted using some recent process developments with an aim to develop a platform for further synergistic innovations.

Jan 1, 2006

By Michael J. Virnig

The formation of crud is a normal part of operating a solvent extraction circuit for the recovery of copper. It periodically must be removed from the circuit. This results in significant costs in terms of manpower, downtime, and loss of circuit organic. Field studies have been carried out that show that the presence of a thermodynamic modifier in the organic phase contributes to crud formation. In an effort to better understand what factors contribute to crud formation, laboratory studies involving competitive adsorption studies with model solids have been carried out. The results of these laboratory studies will be integrated with the results of the field studies to present a better understanding of crud formation.

Jan 1, 1999