Search Documents

By Ragnhild Aune

In fire refining of copper, the affinities of various impurity elements on dissolved oxygen is of great significance. Further, in the design of oxygen probes in liquid copper, the influence of solute interactions on the activity of oxygen need to be considered in order to evaluate the oxygen concentration in molten copper. The present paper presents a series of measurements of the activities of oxygen in liquid Cu-M-o alloys (where M stands for Mn, Zn, As, Se or Te) carned out by the present group employing the solid electrolyte galvanic cell technique. Extreme care was taken to control the oxygen potentials in the inert gas atmosphere, and to keep the oxygen levels very low in the molten metal. The oxygen content was determined by analysis of the samples taken out from the melt. The results obtained showed that Mn has a strong negative influence on the activity coefficient of oxygen in liquid copper. A similar, but less prominent effect was observed in the case of Zn. Arsenic had no influence on the activity of oxygen in Cu (liq.). Se and Te had slight negative effect on oxygen activities in copper at XQ >10-5, while at lower oxygen levels the interaction coefficients were found to be positive. The results obtained were compared with empirical models for the calculation of interaction coefficients available in literature.

Jan 1, 2003

By A. I. Okunev

The investigation results are submitted on separation into layers in the systems Cu (Ni) - Fe - Ca - 0 - S - (Si), as well as on physico-chemical properties of oxide - ferrite, oxide-sulfide melts (density, surface tention, viscosity, electric conductivity), on kinetics and oxidation macromechanism of iron and sulfur in the oxide-silicate, oxide-ferrite and oxide-sulfide melts, kinetics of reduction of oxide-silicate and oxide-ferrite systems. Conditions are discussed for copper, nickel and zinc recovery from oxide-silicate and oxide-ferrite slag in liquid and solid states. Some promising technique is the technique of future, as is considered.

Jan 1, 1988

By B. Willit, J. Martin

"Continued emphasis on water and energy conservation with less operator attention has created a need for more sophisticated cooling tower controls. A joint Betz/ASARCO project has produced a computerized water parameter controller and automated pumpless feed unit. Interfacing the unit via radio modem to the operator control room computer allows real time system status monitoring. Incorporating SPC principles to monitor and regulate all pertinent parameters yielded enhanced water control. This paper described the system design and present the results of a six month trial.BackgroundReducing operating costs and better manpower utilization are two of the largest concerns confronting maintenance managers today. At the ASARCO plant in Amarillo, a trial has been initiated to prove that it is possible to accomplish both of these objectives by using automated cooling tower control. The system is being adapted from a unit that was designed for continuously operating cooling towers in refineries and power plants by Betz Equipment Systems Division, a subsidiary of Betz Laboratories, Inc. The System l3000™ is designed to continually monitor conditions in the cooling system and to provide adjustments to the chemical balance for corrosion and deposition control. At Asarco, the unit was installed on the Rodline cooling system which operates on an intermittent basis.The primary justification for this project is to reduce costs of the five cooling systems in the plant. Current procedures require an operator to make visual checks every two hours on the five cooling towers as well as run lab tests on the water to insure proper treatment levels. This manpower can be better utilized by controlling the towers and collecting all the data available at one central location, in this case, the boiler house."

Jan 1, 1989

By Zuomei Jin

A laboratory study was conducted on the separation of Zn, Pb, Cu and Ag from a finely dissem-inated interlocked silver-rich multimetal sulphidc ore. These are often difficult to separate from each other by flotation. The thermodynamic calculations of Zn-S-O, Cu-S-O systems at different tem¬peratures were presented on predominance diagrams. Based on these diagrams the optimum temperature and gas composition were selected for roasting. The results of separating Zn, Cu from calcine by neutral leaching and acid leaching were found to be satisfactory. The distribution of silver in the roasting and leaching processes were tested. A flow sheet was proposed.

Jan 1, 1993

By P. Stantke

In recent years the CollaMat process has been used successfully worldwide in a number of copper electrorefining tankhouses as an instrument for measuring the glue concentration and optimizing cathode quality. Owing to its measuring principles the CollaMat can be used not just for measuring the concentration of active glue but also the activity of other substances, which have an impact similar to glue on the copper deposition. In SX-EW plants guar is frequently used instead of glue as a levelling additive. In our laboratory the effect (activity) and the decomposition rate of guar in copper electrolyte was examined. As expected, the results show that guar has an effect similar to glue on the copper deposition. However, at the same temperature, a greater quantity of guar is required to achieve the same results. As with glue, the decomposition rate (due to hydrolysis) of guar is strongly dependent on the temperature. Therefore, in practice, its on-line monitoring is necessary to guarantee the same guar activity at any time.

Jan 1, 1999

By Bekir Karasu

Boron raw materials are amongst the most important natural sources for many industrial branches and their values become increasingly raised with the discovery of boron usage in many new technological fields. All the countries in the world are unfortunately not as lucky as Turkiye and USA where major boron deposits are mainly located. It is widely known fact that on one side, boron is very precious component with its technological importance, on the other; only its limited sources are available. Therefore, even its wastes have to be evaluated and regained. In the present work wastes of Etibor Kirka Borax Company of Turkiye were used in the production of opaque frits which was suitable for floor tile glazes. Standard and newly produced frit based glazes were applied on the pre-engobed floor tile bodies and single firing was employed. Final products were examined according to the certain standard tests and their microstructures were also investigated. All the results confirmed the evaluation of boron wastes in opaque floor tile glazes.

Jan 1, 2006

By Khosrow Nikkhah

Increasingly ion exchange systems are being included in design of hydrometallurgical plants for metal extraction or impurity removal. Because such systems operate sequentially and are based on resins that exchange one ion for another, store it temporarily and release it to a regenerating solution, the usual steady state heat and mass balancing tools and spreadsheets cannot be used to design them successfully. This paper outlines the role of dynamic simulation in design of ion exchange systems. Examples are given for use of dynamic simulation in design and investigation of equipment based on consideration of the effect of input criteria such as expected ion loading and elution profiles. The methodology for dynamic modeling using IDEAS in design of multi column ion exchange trains operating in parallel is presented. Results shown include the non-steady state distribution of extracted metal and limitations imposed on operating conditions. These conditions include proposed sequencing of columns for loading and elution cycles, loading, elution and recycle flow rates as well as size and choice of related ion exchange plant equipment.

Jan 1, 2003

By D. Quattrini

The aim of the present work is to present the gas chromatography (GC) as an alternative method of analysis in the thermal decomposition of calcium carbonate. Therefore, a furnace/GC on-line system was employed to study the kinetics of the reaction, measuring the CO2 produced in the decomposition. One of the advantages of the GC method is the possibility to perform an in-situ characterization and quantification of the gaseous products to obtain kinetic parameters, besides the method is simple and shows a good reproducibility. The decomposition of calcium carbonate was carried out in isothermal conditions at temperatures from 655 to 715°C with nitrogen as purge gas. Several gas velocities were used to determine the adequate flow that minimizes the effect of external mass diffusion as rate controlling step. It was made a preliminary analysis of the sample size influence on the reaction rate. The activation energy of the reaction was determined by Flynn method. The value obtained was in a good agreement with other authors. On the other hand, gravimetric measurements were employed for compare GC results.

Jan 1, 2006

By A. V. Tarasov

Technology has been developed for production of elemental sulphur from off-gas from autogenous smelting processes based on reduction of sulphur dioxide with natural gas with subsequent treatment of reduced gas containing hydrogen sulfide by the Klaus method. This technology has been applied on a commercial scale at the copper smelter of the Norilsk Mining and Metallurgical Complex for treatment of off-gas from the Vanyukov smelting process (PV). In the course of further improvement of the technology a catalytic version of the process has been developed based on the use of a catalyst at the reduction stage, which permits a decrease in the natural gas requirement by 25% to 30%.

Jan 1, 2006

By H. Tan

?Preg-robbing? is the active adsorption of gold from cyanide solution by the ore components. The role of carbonaceous coatings on chalcopyrite surfaces in the preg-robbing of chalcopyrite has been investigated by using pure chalcopyrite and a copper concentrate. Activated carbon and graphite were chosen as representative carbonaceous contaminants. It was found that the carbonaceous coatings enhanced the preg-robbing of chalcopyrite. Activated carbon coating increased gold adsorption onto chalcopyrite to a lager extent, in comparison with graphite coating. In the preg-robbing of the copper concentrate, gold adsorption was increased to larger extent at finer particle sizes and at higher contents of activated carbon or graphite. The preg-robbing of chalcopyrite was reduced or eliminated, depending on the concentrations of free cyanide. However, the gold adsorption on the carbon and graphite coated chalcopyrite could not be avoided even at higher cyanide concentrations, and this adsorption was solely attributed to the carbonaceous coatings. Zeta potential studies indicated that the carbonaceous coatings reduced the negativity of the chalcopyrite surface charge. As shown by SEM analysis, gold not only accumulated at the edges and defect sites, but was also spotted on the smooth surfaces of chalcopyrite with carbon or graphite present. XPS results revealed that gold was strongly reduced on chalcopyrite surfaces, with the sulfide ions of the chalcopyrite being oxidized to elemental sulfur. Diagnostic elution indicated three mechanisms contributing to gold take-up by chalcopyrite, i.e. gold reduction, physical adsorption and chemical adsorption.

Jan 1, 2003

By M. Nienoord, O. S. L. Bruinsma, J. A. F. M. Schade Van Westrum, W. H. Sillekens, B. Mehmetaj

Recycling of aluminium is an effective way of enhancing the efficient use of energy and limiting the burden on the environment. Where cascade recycling is an established way of using reclaimed aluminium, closing the recycling chain is currently hampered by the unavailability of suitable techniques for refining contaminated scrap on an industrial scale. To overcome this problem, purification based on fractional crystallisation appears to be a promising option. This implies that the material is to be processed in the semi-solid state; that is, at a temperature where a solid and a liquid phase co-exist. In the current paper, it is shown that zone melting can serve as an indi.cative test for assessing the refining potential of fractional crystallisation processes, since they are both based on the same thermodynamic principle. Next, the results of zone-melting experiments are presented for some representative aluminium model alloys. The BPS-model (developed by Burton, Prim and Stichter) is used to interpret these results, from which it is concluded that the model needs extension to obtain a predictive tool for fractional crystallisation processes.

Jan 1, 2000

By C. Lupi

Zinc chloride electrowinning presents difficulties in obtaining smooth, compact and dendrite free deposits with a high current efficiency due to the presence of undesirable metal ions. However, it is hard to define a level of impurities tolerable in zinc deposition, and despite a lot of research in this field, the reaction mechanisms of the undesired metal ions are still not clearly understood. In this study, the influence of Fe, Cd, Co, Ni and Cu additions were investigated, as well as their synergic effect on the zinc electrodeposition process from chloride electrolytes and on the obtained deposit morphology. The tests were all performed in presence of TBACl which reduces the harmful effect of such impurities on the zinc reduction.

Jan 1, 2003

By Peter Forschner

Classical Mixing Theory is based on applying many fundamental correlations to standard baffled dished bottomed vertical cylindrical vessels with high degrees of symmetry. Horizontal autoclaves operating at elevated temperatures and pressures have been used for more than two decades. All compartments and especially the first and last compartments are asymmetrical. To date no comparison of the effects of the asymmetric geometry on mixing system design and scale-up has been published. The results of investigating solids suspension, mixing time, momentum transfer from the impeller to feed slurry and feed inlet location in the first autoclave compartment are presented as influences on residence time distribution. CFD modeling was developed and verified with the test apparatus.

Jan 1, 2003

By M. A. Gerdel

In carboxylate collector flotation of bastnasite from other semisoluble salt type minerals such as barite various modifiers must be added in order to achieve selective flotation. One such modifier is a lignin sulfonate. It may function in part by acting as a sequestrant for metal ions present, preventing autoactivation in the system by metal ions derived from the minerals themselves. It also functions as a depressant for both bastnasite and barite, chemisorbing on both. However, it is shown that the lignin sulfonate functions as a much stronger depressant for barite than for bastnasite. It is suggested that the; strong depressing action on barite is related to a good fit of the sulfonate into the barite structure.

Jan 1, 1989

By J. P. Rodier

Despite the good years that the non-ferrous business is now enjoying, one should not forget that in this business growth rates are low, fixed assets are high and prices are more cyclical than in other businesses. Increasing environmental concern puts the industry under pressure. Lead and zinc companies are now profitable and profitability in the next ten years will depend on size of units, location, and choice between new technology and upgrading current ones. Implementation of Metaleurope was a strategic move. It produced a company of sufficient size to achieve new steps in cost cutting and yet remain flexible enough to deal with rising variety of primary and secondary raw materials.

Jan 1, 1990

By Jong-Shin Chang

The Onsan smelter has tried to do various activities to decrease operation costs. With several expansion projects, the Onsan smelter has aimed at not only a quantitative growth but also qualitative growth through efforts improving operations equipment and processes. Activities to reduce operation costs have been one of those efforts. In particular, the energy cost of operation has been a main target for reduction. The activities to save energy have been carried out in two ways. One is to recover and utilize waste heat as much as possible and another is to replace existing equipment and processes with more energy-efficient ones. This paper reviews recent improvements and future plans for energy saving activities at the Onsan smelter.

Jan 1, 2006

By Pekka Hanniala

The falling real price level of copper metal and changes in the treatment and refining charges has been characteristic to the copper industry during the last few decades. Outokumpu's continuous development of the Flash Smelting Technology and increased productivity of the smelters based on these improvements may be one of the basic reasons that have influenced to these trends. From the early beginning of the Flash Smelting Technology, it has been characterized by low operation costs and low emissions, and the vision has been to develop the technology towards Direct Blister Flash Smelting. In Direct Blister Flash Smelting, both smelting and converting are carried out in one furnace making it possible to reduce the number of unit operation steps and thus lower both operation and investment costs. The merger of large copper production companies taken place during the last few years is a sign of a new age in copper production business. Now, the aim is to increase the productivity of copper production not just by utilizing the economy of scale but also by increasing integration and optimization of the whole production chain from mine to refinery. This also means increasing win- win based cooperation between companies. A Production Network concept based on the Flash Converting process enables existing smelters to decrease the operating costs and expand the smelting capacity with minimum investment and at the same time to decrease the emissions of the smelters. The new structure in ownership and partnership between copper production companies makes it easier to adopt the Production Network concept to both new and existing plants, where there exists a lot of built-in capacity. The paper presents Outokumpu's prediction on how the new options for the smelters will contribute to further changes in the structure of copper production. These visions are illustrated by giving examples on how the combination of matte production, Flash Converting, and Direct-to-Blister Flash Smelting could be adapted in existing and new smelters.

Jan 1, 2002

By Wenshan Zhang

This paper described the present status of China electrolytic manganese industrial production. Electrochemical reactions on cathode and anode, the major technological process, technical requirements on the production and technical index and quality control of the products and the ways of increasing current efficiency during Manganese electrolytic process have been expatiated.

Jan 1, 2006

By Dachun Liu, Yifu Li, Baoqiang Xu, Yongnian Dai, Bin Yang

"The removal of impurity arsenic from crude tin is one of the major problems in the process of tin refining. Through a thermodynamic analysis on vacuum refining process of crude tin, the vapor pressure of impurity arsenic under different temperatures can be obtained, which demonstrates that it is possible to separate tin and arsenic by the vacuum refining process. This paper attempts to verify the behaviors of impurity arsenic. The experiment result shows that through vacuum distillation, crude tin with 0.16% arsenic can be refined from crude tin with 0.96% arsenic, and about 50% impurity arsenic can be collected in the form of metallic arsenic.PrefaceThe crude tin obtained by the reduction process is insufficiently pure for most applications, even smelting from tin concentrate. Arsenic is a common impurity in crude tin and also one of the predominant elements to affect tin performance. Arsenic is a poisonous metal that has long been linked to an increased risk of cancers, diabetes, thickening of the skin, diseases of the liver and digestive complications, so there is a mandatory limit on the amount of arsenic (<0.015%) in tinfoil wrapper and tin layers for food packaging. Arsenic causes a poor appearance and plasticity, and increases viscosity. The impurities content of crude tin fluctuate over a wide range; a lot depends on composition of tin ore concentrate, treatment method and technological process before reduction smelting. And the content range of arsenic is usually 0.5~4%, but it is higher in some factories."

Jan 1, 2012

By B. C. Tripathy

The effects of alkali metal ions Li+, Na+, K+and transition metal ions Cr3+ and Mo6+ on the cathodic current efficiency, deposit quality, crystallographic orientations, deposit morphology and polarisation behaviour of the cathode during nickel electrocrystallisation on stainless steel substrate from aqueous sulphate solutions containing boric acid were investigated. The alkali metal ions had virtually no effect on the cathodic current efficiency, deposit quality, crystallographic orientations, deposit morphology and cathodic polarisation. On the other hand, there were significant variations in the current efficiency and deposit characteristics when Cr3+or Mo6+ were present in the electrolyte. Current efficiency decreased by more than 10% even at lower concentrations (> 100 mg/L). Similarly purity of the deposits was affected by the presence of either of the metal ions. In the presence of Cr3+, there was progressive shifting of the nucleation potential of nickel towards more negative values, whereas, in the case of Mo6+the nucleation potential shifted initially towards positive values in the concentration range 2-40 mg/L, but then towards negative values when its concentration exceeded 40 mg/L.

Jan 1, 2003