Search Documents

By Zhong Juya, Wang Yong, Guo Xueyi, Song Yu, Tian qinghua

"In this work, the flow of zinc in China, 2004, was traced within the STAF model, and the situation of production, consumption and recycling of zinc resources in China were introduced. The SFA is performed on zinc flows during its one year life cycle in detail. The result reveals that China produces and utilizes a large amount of zinc, while the efficiency of renewable zinc resources is still relatively lower. As one of the biggest producer and consumer of zinc in the world, China is facing a severe depletion of zinc resources. How to increase the resource efficiency is a significant issue for zinc industry of China. Based on the result, several advices were proposed in the paper, aiming to contribute important reference information for the industrial metabolism and resource management and recycling of zinc industry in China. IntroductionZinc is one of the important metals in national economic development in China; it has good conductivity and corrosion resistance, with high scalability when heated to 100 ~105_. Zinc is mainly used for galvanized zinc industry, as the coating of steel and various parts, and it has also been applied to the manufacture of brass, bronze and corrosion-resistant alloys, which are widely used in machinery manufacturing, printing, national defense and so on. In addition, zinc compounds are utilized in various fields, for example, ZnO is used for infiltration wood, paper, rubber, paints, etc.; ZnSO4 for leather, ceramics, textiles, medicine, etc.; ZnCl2 for infiltration wood; ZnS2O4 and Zn (HSO2 • CH2O) 2 for the paper and textile bleaching, etc. [1]. The extensive use and consumption of zinc in industrial production and social life promot the rapid development of zinc industry, which made zinc the third largest non-ferrous metals in the world."

Jan 1, 2008

By S. Ikenobu

This paper describes a method for processing high-silicate zinc concentrates by hydrometallurgical zinc refining. Silica in concentrates reacts to form zinc silicate during roasting. The zinc silicate readily dissolves and slowly precipitates in sulfuric acid solutions during leaching. However, if proper operating parameters are not maintained, the colloidal silica may form an unfilterable gel. That is, according to the investigation results obtained, the silica concentration in the reactor has to be maintained at 5 g/1 or less (preferably 2 g/1 or less) by promoting the precipitation reaction. The proposed method has made it possible to precipitate silica in a form having excellent solid-liquid separation characteristics, without the need for facilities having a high filtration capacity, and to maintain a low silica concentration in the reactor by feeding a composition containing pre-adjusted silica contents.

Jan 1, 2000

By Fabio J. Esper, Wildor T. Hennies, Guillermo R. Martín-Cortés, Francisco R. Valenzuela-Díaz, Antonio J. Santana de Araujo, Maria G. Silva Valenzuela

Seeking to replace carbon-black as filler of rubber in the production of vulcanized goods, researchers from University of São Paulo have studied different materials types as minerals, vegetal or wastes agricultural and industry. Results of rubber composites filled with MA1 a waste of mineral treatment provided by Esper Industries are presented. MA1 was characterized through X-ray diffraction; Thermal analysis; Scanning Electronic Microscopy; and others laboratory methods. The composite and shaped masses were evaluated by these methods plus their mechanical properties such as tensile strength, elongation at break and hardness. Exceptional results were obtained in the mechanical properties evaluated, better than those obtained with the traditional carbon-black. Seeing the kind of material used as filler, it can conclude that the environmental benefit is present, as well as economic development, giving credibility to the use of these alternative material in replacement carbon black.

Jan 1, 2015

By Qian Li, Haiyan Leng, Kuo-Chih Chou, Haoyuan Xiao, Zhigang Yu

Magnesium borohydride and Magnesium alanate were synthesized by mechanochemical metathesis reaction. The thermal decomposition behaviors of Mg(BH4)2-nMg(AlH4)2(n=0.5,1) systems were investigated as potential hydrogen storage materials. The results showed that the systems started to desorb H2 at 120 ℃ and desorbed 3.9 wt. and 4.9 wt.% H2 below 300 ℃ when n equals 0.5 and 1, respectively, while individual Mg(BH4)2 started to desorb H2 at 250 ℃ and desorbed only 0.82 wt.% H2. Because of the exist of the Mg(AlH4)2, the isothermal desorption kinetics of Mg(BH4)2 in the Mg(BH4)2-0.5Mg(AlH4)2 systems was 50% faster than that of pristine Mg(BH4)2. In addition, the re-hydrogenation rates also increased 49.4% and 37.9%.

Jan 1, 2015

By R. Escalera-Lozano, M. Herrera-Trejo, M. A. Pech-Canul, J. López-Cuevas, A. L. Leal-Cruz, M. I. Pech-Canul

"The use fly-ash (FA) and rice-hull-ash (RHA) offers the potential for the manufacture of hybrid Al/SiCp/spinel composites via reactive infiltration, both with recycled aluminum. The main reason behind this statement is the beneficial role that both waste materials play in preventing the degradation of SiCp reinforcements when the composites are processed with aluminum in molten state. Experimentally, MgAl2O4 is formed in situ during the infiltration of SiCp-preforms in the temperature range 1050-1150 oC for 50-70 min in argon atmosphere at a pressure slightly above to that of the atmospheric pressure. Results reveal that both FA and RHA help in preventing SiCp dissolution and the subsequent formation of the unwanted Al4C3; and although FA-composites still might be susceptible to corrosion via Al4C3 -by the interaction of native carbon in FA with liquid aluminum- a proper FA treatment significantly mitigates its deleterious effect. Primary corrosion mechanisms and strategies to overcome the potential degradation effects are outlined.IntroductionOwing to inherent materials characteristics and post-processing complications –such as corrosion damage- development of metal matrix composites (MMCs) from recycling/waste sources might be a challenging task. Fly-ash (FA) and rice-hull-ash (RHA) are two primary waste materials that offer excellent opportunities for the development of Al matrix composites. Due to its singular hollow-spherical shape and low density, FA has attracted the attention of many researchers. For this reason, most of the efforts to develop Al-based composites from waste materials have been centered on the use of fly ash. Extensive research efforts in the use of FA for Al-based composites have been undertaken by Rohatgi and coworkers [1-4]. In addition to lowering costs, incorporation of fly ash into aluminum has been proved to decrease the materials’ density, increase their hardness, abrasion resistance and stiffness [1]. One of the major outcomes from the mechanical evaluation of aluminum composites prepared with fly ash is that related to their compression characteristics. Typical compressive stress-strain curves form A356/hollow fly ash composites show a linear elastic region followed by a plateau (associated to the collapse of the hollow particles), and then an increase in stress, representing densification of the foam. The crushing of the cenospheres in the composites has been related to an enhancement in the energy absorption capabilities of the material and to a better damage tolerance [4]."

Jan 1, 2008

By M. M. Sadawy

"The increased rate of exploitation of iron ores has resulted in a rapid depletion of high-grade iron ore deposits in Egypt. New iron reserves have to be discovered to secure the iron ore for steel production. This paper aims to study the characterization and magnetic separation of low grade Aswan iron ore. The results showed that Aswan iron ore is composed of oolitic hematite, goethite, quartz and kaolinite. The screen analysis indicated that Aswan iron ore had a uniform distribution of iron and silica in the different particle size fractions and there is no any particle size has high amount of iron or low content of silica. On the other hand the results of dry high intensity magnetic separation illustrated that this technique is not suitable for upgrading this ore.IntroductionIron is one of the common metals used in industry, as well as being the fundamental raw material used in iron-steel industry; products are wide spread even in daily uses. The total iron ore reserves of the world have been estimated as 3 70 billion tones; 160 billion tones is classified as economical, while 210 billion tones as potentially economical [1]. An estimated 98% of the iron ore exploited in the world is used in the manufacture of pig iron and steel, which are non-substitutable backbones of modem society. The rapid increase of world steel production over the last few years have required an equal increase in iron ore production, from 876.8 Mt in 2006 to 948.1 Mt in 2007 [2]. The increased rate of exploitation of iron ores has resulted in a rapid depletion of known high-grade iron ore deposits. This, in turn, has led to a dramatic increase of prices. In the absence of any major new discoveries of high-grade iron ore deposits, mining companies have turned to lower-grade materials to assess their beneficiation potential to expand their production base and beneficiation capacity, in order to satisfy future demand. Egypt is going to face shortage in iron production, consequently new iron reserves have to be discovered to secure the iron needed for the country [3]. Exploitation of low grade ores requires special equipments and techniques for recovery of minerals values. High gradient magnetic separators offer promise and great potential of application both technologically and economically in the processing of fine particles containing weakly or feebly paramagnetic components [4-6]. Within this existing framework, this research was initiated to assess the beneficiation potential of low-grade Aswan iron ore by high intensity magnetic separation."

Jan 1, 2013

By Javier Antoñanzas, Juan Carlos Múgica, Lourdes Yurramendi

The gasification of wastes containing an organic fraction is usually performed at low-medium temperature using different kind of catalysts. The off gas obtained is a mixture of carbon oxides, mainly carbon monoxide, and hydrogen and can be used for different energetic applications. The main problem is the production of tars in the off gas that has to be separated from the valuable gas flow and, finally, treated separately. An interesting alternative is the partial or total treatment of organics at high temperature. In this case, the off gas contains a higher content of hydrogen and elemental carbon as particulate matter. The energetic source to obtain a temperature in the range of 1,000 - 1,200 ºC is obtained by a plasma torch. In order to make de process attractive, an important issue to be considered is to commercialize the carbon obtained for different industrial applications.

Jan 1, 2008

By Kejun Liu

Platinum and palladium are usually dissolved together and followed by separation. In this study, the selective leaching of platinum and palladium from a secondary resource, such as dental waste, by using chloride solution (hypochlorite and chlorate) has been developed. Results indicate that about 100% of palladium could be initially extracted by the combination of 0.3 mol/L sodium hypochlorite (NaClO) and 0.068 mol/L sodium chloride (NaCl) at pH 1.2 and 298K in 1.5 hours, or the combination of 0.005 mol/L sodium chlorate (NaClO3) and 6 mol/L hydrochloric acid (HCl) at 298K in 0.5 hour. About 100% of platinum could be extracted from the residue by the combination of 0.47 mol/L sodium chlorate (NaClO3) and 12 mol/L hydrochloric acid (HCl) at 298K in 2 hours.

Jan 1, 2003

By Maura Malone, Neil Gao, Daniel Liu

"Corrosion is the primary failure mode for aluminum cathode sheets used in Teck's Trail Operations electrolytic zinc plant. It was observed that the corrosion performance of Al cathodes from different suppliers varied considerably. This suggests that the material properties of Al cathodes have a strong influence on corrosion resistance. In the current study, various types of Al alloys, including 1050, 1060, 1070, HIS and 1090, were characterized through chemical analysis, corrosion testing, mechanical testing and metallography. The results are discussed with a focus on the effects of impurity elements and second phase particles on corrosion resistance. The findings were used to improve the Al cathode sheet specification and to develop a standardized screening procedure which details qualification steps for comprehensive evaluation prior to a plant trial.IntroductionAluminum (Al) cathode replacement is a major operating expense at Teck's Trail Operations zinc electrolytic plant. Currently, approximately 0.5% of daily stripped Al cathodes are removed from service because of failures caused mainly by corrosion. Edge corrosion and acid (solution) line corrosion are the most severe types of corrosion, resulting in more than 50% of cathode failures.Corrosion of Al cathodes has been intensively investigated for over two decades and the origins and mechanisms of Al cathode corrosion are well understood [1-4]. Halide anions contained in the electrolyte are the primary culprits for the corrosion and sticking problems of Al cathodes. Both fluoride (F') and chloride (Cl"") result in localized passivity breakdown on the surface of the Al cathode, causing pitting corrosion. Bouarzaiga investigated the corrosion of Al cathode samples partially immersed in electrolyte and found that the formation of Ch at the electrolyte/air interface was the primary contributor to solution line corrosion [2]. Because of the significant impact of F"" and Cl"" on Al cathode corrosion, it is imperative to maintain these concentrations as low as possible in the electrolyte."

Jan 1, 2012

By Robert Kozicki, Eric Graham, George Wrightson

"IntroductionThe manufacture of Ferro Chromium involves the smelting of various ores and fluxes to produce the metallic product.Slag is inherent in the process. It has a much lower density than the metallic FeCr. Some chrome may be trapped in the slag as either FeCr or Cr203.Previous methods to estimate the slag in the FeCr have revolved around separating the slag and metallic portions by exploiting the differences in density. The downside with that procedure is that material will often contain pieces that are adhered FeCr and slag. The Metallic FeCr may also be completely encapsulated in the slag.An alternative and more precise method involves calculating the slag content based on chemical analysis of Mg and Al. The Mg and Al will be at relatively low levels (less than 0.1 % ) in the Metallic FeCr pieces and considerably higher in the slag (3% or greater). The overall sample will have a proportional amount and is calculated using simultaneous equations with the assumption there is only one kind of slag and one kind ofFeCr present. ""Pure"" slag and ""pure"" FeCr are needed in order to determine the Mg and Al in each. The detemlination of the Mg and Al in the overall sample would then be used to calculate the amount of slag.When the particle size is small, it is difficult to sample and get ""pure"" pieces of the slag and FeCr of sufficient quantity to perform a proper analysis. Often, historic data is used but that is dependent on the source of the FeCr and the materials used in its production. Mg and Al levels in slag can vary between 3% and 20% in different FeCr slags depending on their origin."

Jan 1, 2013

By Samir N. Shoukry, Mourad Y. Riad, Gergis W. William

"Setting of concrete material is defined as the transitional period between states of true fluidity and true rigidity. Initial and final setting times are measured in the laboratory on the mortar sieved from the mix in a controlled environment where temperature and moisture values are constant. On the other hand, field applications are held in outdoor environments where environmental variations have direct impact on setting time values. In this study, initial setting time of class K concrete, usually used for bridge decks and concrete pavements, are investigated highlighting discrepancies between laboratory and field measurements. 72 mixes have been cast in variable environments and collected data from concrete mixes and the ambient conditions are reported. In light of the collected data, the effects of variable setting times on early age cracking of concrete material are studied and means to minimize such cracks are presented.BackgroundSetting of concrete material is defined as the transitional period between states of true fluidity and true rigidity [1]. Continuous hydration of the cement within the matrix transfers the mix from a state of setting to hardening. Initial and final Setting times are measured in a laboratory setting following ASTM C 403 specifications. Initial setting approximates the time at which the cement paste can no longer be plastic under compaction (or can be handled in a proper fashion), while the final setting approximates the time at which hardening occurs. The standard test described in ASTM C 403 is conducted on the mortar sieved from the mix (paste passing from 4.75 mm sieve opening). Initial and final settings are described as the elapsed time after the initial contact of water and cement till the mortar reaches a penetration resistances of 3.5 MPa (500 psi), and 27.6 MPa (4000 psi) respectively."

Jan 1, 2012

By Kazuki Morita

Dissolution mechanism and solubility of chlorine in the oxide melts, such as CaO-SiO2-Al2O3 (-Na2O), Na2O-SiO2-Al2O3 and CaO-SiO2-FeO systems, have been equilibrium technique was employed with controlled Po2 and PCl2, (Po2 = 10-6 -10 19 atm, PCl2 10-6 -10-13 atm at 1673-1748 K). The solubility of chlorine in the 40mass%CaO-40mass%SiO2- 20mass%Al2O3, slag was found to vary in proportion to Pb2/ w and pc/z/p' which proved that chlorine dissolved in the melts as C1 anion. Hence, the chloride capacity (CCI-), indicating the ability of molten oxide to absorb chlorine, has been defined as; The Ccl value was observed to increase with increasing slag basicity and temperature, and showed a reasonable relationship with that Of CS2-. Based on the result obtained in the present study, chlorine distribution during incineration with slags was predicted quantitatively.

Jan 1, 2003

By Steven C. Torma

The present article reviews some of the technologies available for recycling high-energy yield explosives loaded projectiles. These activities lead to reduction of military ammunition stockpiles and their conversion into commercial and industrial applications. The recycling technologies involve dismantling and separation of ammunition components into recyclable metals, plastics, paper and explosive materials. The metal 1 ic components will be sent to smelters, where they will be converted to products that can be used in a variety of industries, such as construction, automotive, housing and so on. Plastics and paper will be recycled and reused. Explosives will be recycled to be used for industrial purposes in the mining industry. Propellants (ammonium nitrate and ammonium perchlorate) can be ground to small particle size and treated to be used in the agricultural industry as fertilizer. In addition, some of the excess explosive material recovered in the demilitarization process may be incinerated to produce energy for steam production for heating purposes, or for production of electricity. Furthermore, this article reviews the developments in the bioremediation of explosive contaminated soils and industrial effluents.

Jan 1, 1994

By R. C. Hubli

Copper (II) chloride has proven to be an efficient lixiviant for copper sulphide ores and secondary sources of copper such as scrap. Nickel sulphides are generally associated with copper ores and copper-nickel matte is an intermediate product of processing mixed sulphides. While the copper species in aqueous chloride media are present as chlorocomplexes, the presence of nickel as Ni++ offers effective separation between the two by solvent extraction techniques. Oxidation of millerite by cupric chloride in sodium chloride solutions has been studied as a function of rate of agitation, leaching time, temperature, acid concentration and total initial cupric concentration. The reaction has a 1/2 order of dependence on initial cupric concentration in the range of 0.0 to 0.5M. The activation energy for the temperature range 333 -363 K has been found to be 59.2 kJ/mol with chemical reaction at the unreacted mineral surface as the rate controlling step. The rate expression, according to the shrinking-core model, for initial cupric concentrations between 0.0 to O.5M, is evaluated as

Jan 1, 1996

By Steven E. Follin

In-situ leaching is commonly used to recover uranium from low-grade deposits in sandstone formations. Acceptable recovery rates can only be obtained if the formation retains its permeability during leaching. Field experiences indicate that microbial growth, stimulated by the leaching pro- cess, can cause plugging problems. To investigate this hypothesis, leach solution and solid samples from well casings and submersible pumps were obtained from four in-situ mining sites. Chemical and microbiological analyses were performed. Bacillus species, Micrococcus species, pseudomonads, and xanthomonads were isolated from these samples. A mixed culture of these organisms was inoculated into a uranium core that was being leached in the laboratory. The permeability of this ore sample decreased to one-third its original value after 16 days. The addition of hydrogen peroxide (0.2 g L-1) to the leach solution killed the microbes and restored the permeability to its original value. This suggests that periodic injection of hydrogen peroxide into production wells may reduce microbial plugging in these wells and the immediate surrounding formation.

Jan 1, 1985

By Chen Yongming

In order to eliminate the serious environmental pollution caused by low concentration of sulfur dioxide smoke in antimony smelters, a new smelting process, named as reducing-matting smelting, is proposed in this paper. The effects of technical conditions such as smelting temperature, smelting time, Pyrite cinder addition and the amount of additive on the smelting of stibnite concentrate have been investigated by the method of single-factor experiment. The results show that the optimum conditions are as follow: The amount of pyrite cinder is 1.2 times of its theoretical amount. The addition of soda and sodium sulfate is 15% and 72.6%, respectively, to the amount of stibnite concentrate when the total amount of sodium is 30%. The reducing-matting smelting is conducted at 1100°C for 2h then the smelting temperature is raised to 1200°C for 50min. Under the optimum conditions, the direct and total recovery ratio of antimony can gain 90.99% and 98.87%, respectively, and the fixed ratio of sulfur is higher than 99%.

Jan 1, 2006

By L. Béjar-Gómez

The aim of this research work is to study and characterize the precipitates in structural microalloyed steel by transmission electron microscopy and analysis by low resolution. Microalloyed steel with niobium was produced by casting in an electrical induction oven of 25 Kg capacity. Carbon content in steel was less than 0.1 % and 0.036% of niobium. Steel was processed thermomechanically; reheated to 1250 °C and hot rolled on a laboratory mill to a 13.0 mm thick plate with a finish rolling temperature of 900ºC and a thickness reduction of 80% . This work shows what precipitates are present in steel, the type of precipitates and their morphology. Analysis by transmission electron microscopy of low resolution was applied to obtain the chemical analysis of precipitates and the matrix. Spectroscopy of dispersive energy (STEM - EDS) was applied to obtain the element profile of precipitates. Particles of precipitates of NbC were found; with cubic morphology and size from 70 to 130 nm, circular morphology and size from 10 to 70 nm, polygonal morphology and size from 10 to 80 nm.

Jan 1, 2006

By Joo Hyun Park, Kyu Yeol Ko

The viscosity of the CaO-SiO2-xMnO-yCaF2 slags (C/S=1.0; x=10, 40%; y=0 to 15%) was measured to clarify the effect of CaF2 on the viscous flow of molten slags at high temperatures. Furthermore, the Raman spectra of the quenched glass samples were quantitatively analyzed to investigate the structural role of CaF2 in a depolymerization of silicate networks. The critical temperature of the slags abruptly increased at 15%CaF2, which was confirmed to originate from a crystallization of cuspidine using XRD analysis. The viscosity of the slags continuously decreased by CaF2 addition in the 10%MnO system, whereas the viscosity of the 40%MnO system was not significantly affected by CaF2 addition. The effect of CaF2 on the viscosity of the slags was quantitatively analyzed using micro-Raman spectra of quenched glass samples accompanying with a concept of silicate polymerization index, Q3/Q2 ratio. A polymerization index continuously decreased with increasing content of CaF2 in the 10%MnO system, whereas it was not affected by CaF2 in the 40%MnO system. Consequently, the bulk thermophysical property of the CaO-SiO2-MnO-CaF2 slags was quantitatively correlated to the structural information.

Jan 1, 2014

By S. F. Cheng

Among the many extraordinary features of the rare earths are their magnetic and magnetoelastic properties. The rare earths, e.g. Tb, Dy, Nd, Sm, are known worldwide for their large magnetocrystalline anisotropy and magnetization, which has led to the importance of magnetic rare earths as vital ingredients of modem permanent magnets. In this paper, we focus on the strain dependence of these giant effects which gives rise to huge magnetostrictions, magnetomechanical couplings, and ?E effects. Magnetostrictions greater than 10-3 have been measured at temperatures as high as 500 K. At low temperatures magnetostrictions reaches -1%. ?E effects - 10. No other solid state material has matched these values. A proper balance of magnetic anisotropy and magnetostriction, plus a proper choice of crystal axes lead to alloys which can switch large quantities of energy between the internal (magnetic) and external (mechanical) states with the application of small triggering magnetic fields. In addition to the traditional use of these materials in transduction, they are particularly valuable for smart systems where reliability and robustness are needed such as active structure stiffening and active vibration control.

Jan 1, 1997

By R. Togashi, S. Kuramochi, T. Yamada

In 1972, the Akita Zinc Co., Ltd. commenced operations with an annual capacity of 86,000 tonnes of electrolytic zinc, and it has operated with an annual capacity of 156,000 t-Zn since 1974. The business surroundings for non-ferrous metals production have become more severe with the high Yen rate for the dollar and low domestic demand in the last few years. Consequently, the company tried to survive with some improvements and succeeded to reduce operating costs and to improve profitability as follows: 1) expansion of its production capacity to. 196,000 t-Zn annually, 2) saving man-power by the introduction of fully-automated machines for cathode handling in the cellhouse, 3) improvement of the hematite process by means of the recovery of rare-metals. These improvements made Akita Zinc a competitive refinery in the modern world. We have been trying to improve the operations more and more. One of the challenges is to purify the iron oxide made in the hematite process by applying an As removal process, which is coming into operation in the near future.

Jan 1, 2000