Search Documents

By Bart Blanpain, Muxing Guo, Zhuangzhuang Liu

In order to stabilize free lime in the basic oxygen furnace (BOF) slag to achieve high value products, quartz sand and other additives are injected into slag. However, the current hot stage slag stabilization does not work in case of slag (before treatment) with a liquid fraction lower than 90%, where the slag containing solid particles is too viscous. Therefore, it is essential to understand how solid phases affect the viscosity of the slag system. In this study, the industrial BOF slags were investigated with respect to the correlation between volume fraction of solid phases and its viscosity. Slag viscosity was measured with a rotating type viscometer at temperatures below the liquidus. The volume fraction of solid phases was quantitatively calculated with FactSage. The Einstein-Roscoe equation was employed to predict the viscosity of BOF slag.

Jan 1, 2016

By M. I. Novgorodova

An overview of the systems Au-Ag and Au-Cu is given. The nature and levels of concentration of various elements occurring with native gold is reviewed. The examples cited are mainly from the USSR. The lack of homogeneity within naturally occurring Au-Ag solid solutions is examined.

Jan 1, 1991

A strategy is presented for a relatively. "low-tech" means for decontamination of streams . containing .low concentrations of toxic metals. Metal ion solutions were . circulate through fluidized beds of activated carbon which support bio-films ?of bacteria .that naturally excrete exopolysaccharides. The attached 'biomass is shown to significantly enhance nickel, cadmium and silver extraction from dilute solutions (5- l00mg/l). By heat treating (at 300º C) the metal/biomass/carbon particles, bio-sorbed silver was subsequently fixed to the carbon surface. This approach to metal decontamination may therefore also provide a route for dispersing and fixing catalytic metal particles over an activated carbon surface.

Jan 1, 1991

By C. M. F. Vieira

The main characteristics and physical and mechanical properties of clays from the county of Campos dos Goytacazes, located at the northern part of the State of Rio de Janeiro, Brazil, are presented. The characterization included mineralogical composition, chemical composition and particle size distribution. The properties related to water absorption, linear shrinkage and flexural rupture strength were obtained in samples that were prepared by 20 MPa uniaxial pressing and fired at 950 and 1100oC. The results showed that the clays are predominantly kaolinitic with high percentage of clay minerals. The kaolinitic structure associated with a small amount of fluxes confers a refractory behavior which makes difficult the sinterization and impairs the ceramic consolidation.

Jan 1, 2009

By Takaaki Ishikawa

The distribution equilibria of lead, zinc and copper between CaO-Si02-Ah03 melts and liquid copper were measured at 1623K under a controlled H2-C02 atmosphere. The distribution ratios were plotted against the oxygen partial pressure, and reasonable oxide forms dissolved in the melts were estimated from the slopes of the plots. The activity coefficients of zinc oxide (ZnO), lead oxide (PbO) and cuprous oxide (CuOQs) increased with increasing slag basicity, defined by Xcao /XSiO, The temperature dependence of the activity coefficients was also measured.

Jan 1, 2003

By L. H. Gevantman

A program for the compilation of evaluated physical and chemical numerical properties data is being pursued at the National Bureau of Standards within the Office of Standard Reference Data. This program is being sponsored by the Department of Energy and managed by the Battelle Office of Nuclear Waste Isolation in Columbus, Ohio. The intent is to assemble a reliable body of numerical properties data concerning candidate mineralogical materials in which high-level radioactive wastes are to be buried. The ready accessibility of the data to site designers and the credibility achieved through the evaluative process are designed to help assess and compare the feasibility of each candidate material for use as a disposal site. Both generic and site-specific data are to be assembled. To date, generic rock salt properties have been assembled and published by the NBS as NBS Monograph 167. Details of the effort to produce this book are discussed.

Jan 1, 1982

By Baozhong Ma, Yonglu Zhang, Yongqiang Yang, Chengyan Wang, Yongqiang Chen

During the past decades, slurry electrolysis (SE) has been implemented commercially for the processing of bismuthinite and complex Pb-Cu bearing gold concentrates. Recently, SE was proven effective for the treatment of As-rich antimonic gold concentrates. Laboratory test results suggest over 98% of the antimony was extracted, while the extraction of arsenic and gold was less than 0.5%, and that of iron was less than 6%. Moreover, the cathode antimony contained over 98% antimony and less than 0.3% arsenic. Considering the disadvantages of traditional 3 kA slurry electrolysis baths, such as smaller electrode area, reduced capacity, and greater electrode deterioration, the authors have developed an innovative 12 kA slurry electrolysis bath equipped with mesh and fence type titanium alloy electrodes. Furthermore, the technique was successfully used within a pilot scale plant yielding results similar to those observed in the laboratory. The technique yielded ametallic antimony ingot of 99.9% purity after arsenic removal via the addition of Na2CO3.

Jan 1, 2014

By Dae Jin Ha

Sticking phenomenon occurring during hot rolling of two STS 430JlL ferritic stainless steels was analyzed by hot-rolling simulation tests. The sticking started from the initial nucleation stage in which the rolled materials were stuck onto the roll specimen surface, proceeded to the growth stage in which stuck fragments grew further, and reached the saturation stage. The modified 430JlL steel had a smaller number of sticking nucleation sites and slower growth rate than the conventional 430JlL steel because of higher high temperature hardness, thereby leading to less serious sticking. When the simulation test was conducted at 1070 °c, Cr oxides were formed on the surface of the rolled materials, and thus the sticking was drastically reduced because of the increased surface hardness of the rolled materials. In order to prevent the sticking, high-temperature properties of the rolled materials should be enhanced when rolled at 900°C or 1000 °C, and rolling conditions and alloying compositions, under which the oxide formation was promoted, were more important than high-temperature properties when rolled at higher temperatures than 1000 oC.

Jan 1, 2008

By Jesus Gonzalez

Peirce-Smith converters (PSC) are long cylindrical chemical reactors where copper matte reacts with air. Traditionally, air is injected laterally through submerged tuyeres at different subsonic velocities. However, the accumulated experience in steelmaking, particularly in the basic oxygen furnace (BOF) process, shows that the gas bottom injection may improve the mixing efficiency of a liquid pool. The aim of bottom injection is to maximize the copper kinetic energy meanwhile avoiding excessive reactor splashing. When gas is injected from a single orifice at the bottom of a liquid pool, two main gas flow regimes can be identified, bubbling and jetting. In this work, a PSC with bottom air injection is studied by means of multiphase 3D CFD numerical simulations considering multiple air velocities. Special attention is paid to the bubbles and jet formation mechanism. The mixing efficiency is measured by calculating the turbulent kinetic energy of the copper matte.

Jan 1, 2008

By Nourreddine Menad

Plastic materials have been associated with electric and electronic applications since the early days of the electrical industry. Plastics can amount to 30 percents of the scrap mass. Generally, they are treated with flame retardants such as halogenated ones and they can result in different toxic chemical compounds. These plastics can be used as combustibles in the recovery of copper and precious metals. However, during their combustion, halogenated flame retardants can produce dibenzo-p-dioxins and dibenzo-furans. The estimated thermodynamic data of several organic compounds resulting from combustion of electric and electronic scrap, have been used in conjunction with the program HSC to calculate the conditions for dioxin and furan formation. The results show that the formation of the dioxins is dependent on the quantities of carbon, hydrogen, chlorine and oxygen reacting in a given system, as well as on parameters such as temperature and pressure.

Jan 1, 1998

By D. de la Villa

From 1989 to 1992 Rio Tinto Minera has developed and implemented a productivity program in its Huelva Plant, including Smelter, Acid Plant and Electrorefinery. This Plan was designed in order to increase productivity, reduce emissions and produce a better quality of cathodes. This paper describes investments and operating improvements involved in this project, focusing on Smelter and Acid Plants, and comments the results obtained so far.

Jan 1, 1993

By R. V. Kumar

"The use of sensors to monitor gaseous species in industrial processes is discussed. All of the existing systems have disadvantages. Sensors, based upon solid electrolytes, which can be placed directly into the gas stream are attractive but many also respond to oxygen, need to be sealed at high temperatures and require a separate reference. This paper describes sensors, usually based upon two electrolytes, which do not respond to oxygen and do not require high temperature gas seals or separate references. The application of these sensors to the measurement of carbon dioxide, sulphur dioxide and trioxide and hydrogen chloride is described. These sensors can be placed directly into the gas stream at elevated temperatures.IntroductionOn-line gas sensing is becoming more important as concerns regarding the environment mount. There are many established techniques for monitoring gases in industrial processes, with applications in safety monitoring, chemical analysis or process and emission control. Flue gas analysis involves the greatest technical complexity, requiring several sophisticated capital-intensive spectroscopic instruments for different species as well as needing highly skilled operators. There are also several instruments, based upon aqueous electrochemistry, which are available for the analysis of the gases S03, S02, N02 but these require that the gases are sampled at high temperature and cooled, prior to analysis. These instruments cannot be considered as giving on-line measurements of the gas composition. Furthermore, the power requirement of these instruments frequently precludes battery operation for field and domestic use."

Jan 1, 1997

By Jin-tao Gao

In order to recover Ti resource from titanium bearing blast furnace slag, a new technology to separate perovskite phase from CaO-TiO2-SiO2-Al2O3-MgO system by supergravity is researched. In the condition of gravity coefficient of 750g, treatment temperature of 1305°C and time of 20min, the significant layers appear in samples which are obtained by means of centrifugal treatment. Along the direction of the supergravity, the volume fraction of perovskite phase increases gradually, and the equivalent diameters of perovskite phase crystals increases with the area approaching to the bottom of the sample. It is indicated that TiO2 is enriched in the bottom of sample as concentrate with a recovery ratio of 74.05% by supergravity treatment.

Jan 1, 2014

By Desmond Cook, Cynthia P. Dogan, Dale Govier, Gary Korth, James C. Rawers

"The microstructural and mechanical properties of iron powders processed in an attrition mill are highly dependent upon the processing environment. Extended high-energy ball milling in argon resulted in nanocrystalline bcc-Fe microstructure, while processing in nitrogen or alloying with carbon resulted in both nanocrystalline bcc-Fe and bct-Fe microstructures. In this U.S. Bureau of Mines study, both X-ray diffraction and Mössbauer analysis were used to show that the infused carbon and nitrogen concentrations were predominantly on the grain boundaries. Explosive consolidation resulted in a fully dense product with microstructure similar to the microstructure of the mechanically processed powder. Hardness values of the compacts correlated highly with grain size, independent of the processing conditions.IntroductionNanocrystalline materials have been theorized and shown to have unique properties that make them interesting for material scientists and promising for material engineering applications. Several conferences have been devoted solely to the techniques of preparing nanostructured materials have been held(l,2,3.). To date, most techniques used to generate nanocrystalline materials produce only a few grams of particles(1). High-energy ball-milling, however, is an efficient and effective technique that can produce substantial quantities of nanocrystalline materials with homogenous chemical composition that cannot be produced by conventional processing techniques(3).Applications and material evaluations of nanocrystalline materials require several grams of solid samples. Because nanocrystalline microstructures' are thermodynamically unstable, producing consolidated macro structures of nanocrystalline material has proved to be very difficult(2,3). In particular, retention of the nanocrystalline microstructure during consolidation of nanocrystalline particles has proven to be a problem. In contrast to many consolidation techniques that require elevated temperatures, explosive compaction uses a shock wave for consolidation( 4,5)."

Jan 1, 1994

By Ximeng Zhu

In the transpassive region, about 0.4 to 0.8 V (SCE), aggressive oxidation of pyrite occurred. The reaction products in this region were Fe(III) oxide, sulfate ion and partially oxidized sulfur intermediates. The growth kinetics of the reaction product film, resulting from transpassive oxidation of pyrite were studied using chronoamperometry measurement with both stationary and rotating disk electrodes. The effect of electrode rotation speed, solution pH and temperature were examined. Potentiostatic measurements were well correlated by a paralinear rate equation, suggesting the formation of an intermediate passive film, associated with the simultaneous dissolution of the outer layer of the film. Activation energies of 66.17 kJ/mole (15.83 kcal/mole) and 38.67 kJ/mole (9.25 kcal/mole) were obtained for associated parabolic and linear rate constants respectively, at an applied potential of 0.6 V.

Jan 1, 1993

By Pinakin C. Chaubal

Today?s steel industry is in a vibrant and resurgent mode. This transformation has been in the making for some time now. Over the last few decades, the industry was steadily transforming itself into becoming a high tech industry. New technology was adopted, efficiencies were enhanced, lean manufacturing concepts were brought in and a strong customer focus was developed. Today?s mills employ sophisticated instrumentation, computerized monitoring, on-line smart systems etc. driving processes that are producing at rates of many tons/minute. All this is not possible without judiciously using the latest available technologies in various fields and developing a more sophisticated work force. Prof. Sohn has been a pioneer in driving the concept of process engineering in process metallurgy. In this paper the focus is on some aspects of process engineering ? primarily process modeling - as applied to iron and steelmaking processes. Examples are shown to demonstrate how problems have been addressed. Some thoughts on future directions are presented.

Jan 1, 2006

By Xiaojie Gao, Jingshe Li, Chengsong Liu, Haiyan Tang

In order to clarify the reaction between MnO-SiO2 oxides with low FeO content and Fe-Mn-Si alloy, two diffusion couples were produced by the new method using confocal scanning laser microscopy (CSLM). The interface of the alloy and oxide, content of Mn and Si in the alloy near the interface, size distribution and composition of the particles which precipitated in the alloy were observed and analyzed using the electron probe microanalysis (EPMA). Results show that though the FeO content in the oxides decrease to 1% which is lower than the equilibrium with the molten steel at 1873K, the diffusion of oxygen from oxide to alloy still exists during the heat treatment at 1473K and causes shorter Particle Precipitated Zone (PPZ) and Manganese Depleted Zone (MDZ) normally for the reduction of diffusion flux of oxygen.

Jan 1, 2015

By R. M. Reynolds

Engitec Impianti, S?.p.A. of Milan, Italy has successfully designed, constructed and has in operation state-of-the-art battery breaker systems at two European locations. A third facility i:s partially completed in Toronto, Ontario, Canada. The CX system crushes whole batteries, separates the various components and desulfurizes the battery paste. The system also produces sodium sulfate from the sulfuric acid and lead sulfate contained in the batteries. Actual plant operating data indicates that the desulfurized paste contains less than 0. 6 percent sulfur and less than 0. 5 percent antimony. The CX system utilizes mechanical screening and an up-flow hydrodynamic separator to accomplish the component separation. Sodiwn hydroxide or sodium carbonate is used for desulfurization. The sodium sulfate brine is evaporated and crystallized to produce clean anhydrous sodium sulfate suitable for use by detergent or glass manufacturers. Plant data also indicates that an increase in furnace productivity of about 25 to 30 percent is achieved using feed from the CX system. The desulfurized paste is very suitable for electrolytic processing as an alternative to pyrometallurqical processing.

Jan 1, 1990

By Charles A. Sorrell

Two red muds, two fly ashes, and several aluminosilicate minerals were subjected to direct treatment with concentrated H2SO4 at temperatures of 175°C and below. X-ray analysis showed that virtually all the sulfate reaction products remained in the solid residue because of their low solubilities in x SO Substantial portions of the Al2O3 Fe2O3TiO2, Na2O, and K2O components of the materials reacted to form water soluble sulfates, which were then removed by H2O leaching at 55°C. The solid residue after water leaching consisted largely of amorphous silica and, in lime bearing compounds, CaSO4, The reaction and leaching processes were effective in removing all or nearly all the Al2O3. Fe2O3, TiO2, Na2O, and in lime components in the fly ashes, red muds, china clay, bentonites, the nephelioe fraction of nepheline syenite, and a plaster insulating brick composed of anorthite and mullite. Reaction with potassium feldspar and petalite took place, with formation of alkali aluminum sulfates, but the reaction rates and yields were extremely low. Potassium feldspar can be heated with Na2O and x O in air at 700°C for 24 hours, or with CaO at 1000°C for 24 hours, after which the reaction product kaliophilite, nepheline, and leucite-like phases, prove to be very susceptible to H2SO4, reaction and H2O leaching, providing yields near 100% of the Al2O2 content. An alternative method of H SO treatment consists of heating the sample in a silica tube and passing H2SO4 vapor over it. Preliminary results indicate that this method can be effective in enhancing the kinetics of reaction with the Al O component of potassium feldspar and offer the possibility that formation of Al2 (SO ) Fe2(SO4)3 and TiOSO4 can be accomplished selectively by taking advantage of the fact that the upper stability limits of the respective sulfates in the presence of H2SO4 vapor will be different.

Jan 1, 1982

By Takaaki Ishikawa

The distribution equilibria of lead, zinc and copper between CaO-Si02-Ah03 melts and liquid copper were measured at 1623K under a controlled H2-C02 atmosphere. The distribution ratios were plotted against the oxygen partial pressure, and reasonable oxide forms dissolved in the melts were estimated from the slopes of the plots. The activity coefficients of zinc oxide (ZnO), lead oxide (PbO) and cuprous oxide (CuO0.5) increased with increasing slag basicity, defined by XCao/Xsio2 The temperature dependence of the activity coefficients was also measured.

Jan 1, 2003