Search Documents

By A. Bortolussi

The paper discusses the state of the progress reached in the development of the diamond wire tool for cutting hard rocks. To the advances of this relatively new technology a substantial contribution has been provided by the research being carried out at the University of Cagliari on samples of granite rocks from different Sardinian stone quarries. On the basis of field experiments and laboratory test data, the mechanism of diamond wire cutting has been assessed. In particular the influence of the rock features and operational variables an tool performance (cutting rate and bead wear) has been elucidated.

Jan 1, 1992

By Thomas Barczak

Longwall mines typically use some form of standing support for secondary roof support in longwall tailgate entries. Although there have been several new support products developed for this application, there remains no universal design criteria to optimize the application of these support technologies. The requirement for optimization and proper support selection is to understand the degree of control that the support has on the ground behavior. The ground reaction curve and numerical modeling was used to evaluate the impact of standing support on ground behavior. LaModel was used to evaluate the impact of standing support on main roof and floor behavior and pillar yielding. The conclusion drawn from this study was that standing supports do not have sufficient capacity to control main roof or floor loading or prevent the resulting convergence of the tailgate entry. However, it is imperative that this "uncontrollable convergence" be considered in the support design to prevent premature failure of the support. A FLAC model was used to evaluate the near-seam roof and floor behavior in conjunction with the global vertical and horizontal stresses. The model suggests that standing roof supports can have some impact on the ground behavior as the elastic response of the rock is exceeded and rock structure deteriorates from the stress concentrations that develop around the tailgate opening. During this phase, the capacity and stiffhess of the standing support can be critical to the stability of the opening, as eventually the rock mass will be transformed into a partially detached structure whose weight must be supported by the standing support. This work is part of a ground control program of research at the National Institute for Occupational Safety and Health (NIOSH) aimed at improving mine safety by reducing roof fall injuries and fatalities.

Jan 1, 2005

By John J. Bowders

The stability of surface slopes undergoing subsidence due to longwall mining was investigated to examine the effect the subsidence had on the stability of the slopes. Stability analyses were performed on all slopes along both longitudinal and transeverse sections of the longwall panel before and after subsidence. Both finite- and infinite-slope analyses were performed with both drained and undrained cases. The results indicated that the changes in the stability of slopes due to subsidence were insignificant for the cases analyzed. Although significant lateral ground movements were recorded, these were not attributed to slope failure. Explanations for these movements are presented in the paper.

Jan 1, 1988

By W. G. Pariseau

A new approach to the direct inclusion of the effects of joints and geologic structure in rock mechanics analyses is applied to an elastic analysis of stability of a Lucky Friday undercut and 4111 longwall stope (WL) using the finite element method (FW). The approach is base+ on the concept of equivalent properties of a heterogeneous test volume, but does not depend on the assumption that a test volume is a representative volume element. Comparison with conventional FW results show greater variability in fields of stress, strain, displacement, safety factor and energy densities. Stability requires a knowledge of rock mass strengths as well as elastic moduli.

Jan 1, 1989

A high strength steel strand bolt has been developed by Barrett, Fuller & Partners as a replacement for conventional rigid bars for primary roof support in coal mines. It is based on a 23mm diameter multiwire steel strand with a tensile strength of 55 to 60 tonnes, The paper summarizes the development of FLEXIBOLT flexible roof bolts, their reinforcement performance and their potential to provide operators, currently reliant on medium to high density roof bolting systems, with a viable, low density roof bolting system offering high roof reinforcement capacity along with the option of installing bolts longer than headroom, in a single pass at the face.

Jan 1, 1993

By Xianming Zhou

Mining economics is such that too conservative in safety will result in a considerable penalty in mining cost. However, initial planning and design of a mining project often must be done without complete information. The assurance of economical and safe mining is thus difficult. This study is focused on the improvement of the mine design associated with Zhaoyuan Gold Mine in P.R. China as more information becomes available. Attention is given to the selection of backfill structures. Based on a proposed practical finite element model, a design, which is believed to be not only reliable but also cost-effective, is recommended for further mining operations in this mine.

Jan 1, 1989

By Hani S. Mitri

The behaviour of grouted cable bolts used for rock reinforcement as a means of ground control in hard rock mining is investigated. The study utilizes an analytical model which is based on the variational principle to calculate the shear bond stress distribution along the embedded length of cable bolt. In this paper, a comprehensive parametric study which covers both geometric and mechanical design parameters involved is presented. Special emphasis is placed on studying the characteristics of the grout model represented by Winkler springs. This involved varying the maximum shear strength of the grout, its residual strength and the slip occurring between the cable and the borehole wall.

Jan 1, 1990

By Rossen A. Halatchev

This study introduces a new probabilistic approach to seismic stability analysis of embankments and slopes. The approach is based on Sarma's solution, which is modified through presentation of the seismic force by its horizontal and vertical components; i.e. the force may have an arbitrary inclination. The probabilistic modelling includes Monte Carlo simulation of the shear strength parameters of the soil mass, which are assumed to have a normal distribution. The probability of failure is determined based on the seismic co-efficient, which is treated as a random quantity. The probabilistic approach is illustrated through a solution of a numerical example from an opencast coal mine.

Jan 1, 1992

By Kenny D. Basnett

An analysis of the Roof Falls Data Base (RFDB) for underground coal mines in Illinois for the period 2004?2008 indicated that about 80% of the roof falls occur at intersections and are associated with geologic anomalies or a rapidly changing geologic environment. Most falls are associated with anomalies such as clay dikes, differential compaction faults, shear zones, joints and fractures, and geologic structure. Therefore, a better analysis of the geology with emphasis on mapping anomalies such as joints and fractures and their application is necessary to improve ground conditions and safety. Such studies within Illinois Coal Basin are limited. This paper presents a mapping study of the joint orientations with documentation of dip of the several lithological units that lie directly above the Herrin No. 6 Coal seam around southern Illinois. These units include the Energy Shale, Anna Shale, and Brereton Limestone. The mapping was done in three mines and the data were plotted on a stereographic projection to determine the average characteristics of joint planes. The study mines included two deep underground mines and one shallow highwall mine. This study has helped identify favorable mining and support orientations in areas of highly variable geology. These are currently under review by the cooperating coal company for experimental roof control studies.

Jan 1, 2011

By Mao Bai

Mining in situations where there exists a potential hazard from inundation has always existed in coal mining, and often reserves were left unmined in favor of reserves with no such hazard. However, increased pressure on expanding the minable reserves and on producing low-sulfur coal, has made mining under water hazards necessary in many parts of the world. Recent joint efforts by the authors to develop case-history data bases of mining under water hazards has allowed the bringing together of Chinese and United States experience and guidelines for such mining. In China, mining under water hazards has been successfully accomplished for a number of years, allowing the development of a good data base from which to draw guidelines. In the United States, much more limited experience, and the longer delay in adopting longwall mining compared to the rest of the world, has forced reliance on a more limited data base and European experience. In the United States (and Canada), the data base is continuing to increase as more operations start-up. Developing a generally-applicable set of guidelines for international use, based upon extensive Chinese and other experience, appears feasible. The Chinese and United States experiences are detailed by case histories.

Jan 1, 1995

The purpose and current practice of cable trusses in underground coal mines is briefly outlined and details of various cable truss designs are presented. The main part of the paper describes the in-situ performance of cable trusses installed as secondary supports in gateroads and recovery roads of longwall coalfaces. The performance analysis is based on the results of in-situ monitoring carried out at a number of sites at two underground coal mines within Australia. Truss performance has been assessed as load developed in relation to roof convergence, face position and time. Additionally, the influence of strata conditions, installation pattern/density, roadway layout and geometry have been taken into account. An analytical model has been developed to predict truss loads. The principal variables are listed and the basis of the model is described. Based upon behaviour observed in the field the model has been progressively upgraded and validated against measured performance. Guidelines on truss performance and factors which influence it are presented and the implications of these to the use of cable trusses is discussed. Possible methods for improving truss performance in certain strata conditions are outlined and some comments are made on the value of cable trussing compared to cable bolting in these situations,

Jan 1, 1992

By Francis Kendorski

One of the most dangerous events in underground coal mining is unexpectedly encountering water inrushes from undetected abandoned mines in the same seam. The surest and most confident method is probe drilling either from the mine or from the surface. However, drilling is expensive and may even miss the suspected mine voids entirely by drilling through pillars. Many operators rely upon one or more of several remote sensing techniques for detecting mine voids. However, mine "voids" often are not air- or water-filled open cavities, but are collapsed, rubble-filled chimneyed columns in the strata. Geophysical techniques, such as seismic reflection and refraction, electrical resistivity, magnetics, ground-penetrating radar, and others, often assume a continuous or fractured rock mass that has varying properties which provide the signatures that allow discrimination of one strata from another, or of strata from voids. However, a rubble-filled cavity has rock block-to-rock block contact throughout its volume and can still respond as a continuous rock mass with the rock blocks allowing signal transmission or mass detection, rather than a void space. Hydraulically, a rubble-filled cavity is essentially as transmissive to water as an open mine void. Thus, the problem of detecting a mine void with confidence is significantly compounded.

Jan 1, 2004

By S. Mehrdad Heidari

The concentrator plant is located near a very high (105m), large (- 500m) and steep (a, > 45' ) wall. Geologically, the wall was composed of very complicated formations and broad range of soils and rocks type in which a variety of local typical failures models have been occurred on different soil and rocks formations. The construction of concentrator plant structure and other activities have been overshadowed by these local failures. Safety and risk of huge failures were serious concern. For distinguishing the wall conditions a broad campaign of slope stability investigation with detailed geotechnical drilling on berms of wall have been done and the structure of slope was fully identified and further Lab tests and slope simulation models done. Slope stability of the wall was analyzed and the effects of instability factors were described in short term (for construction phase) and long term (for production phase).The results indicated, if a well-appointed drainage system is implemented, the overall stability of the wall in short term will not cause any particular problem but about long term stability, the wall must be supported by rock bolting, consolidation grouting, shotcrete reinforced with fibers. The results have been confirmed by passing one year after this investigation.

Jan 1, 2005

By Hanjie Chen

Mining experiences have shown that in a pitching seam, roof behavior is significantly different from a flat seam. Uphill mining usually experiences more roof problems than downhill mining. Based on a case study at RAG American Coal Company, Willow Creek Mine, this paper presents the roof control problems experienced in a high pitching seam. Then, finite element modeling is conducted to analyze the roof stress distribution for an entry developed in different directions relative to the seam strike. The results shows that seam inclination has a significant effect on roof stability in terms of tensile stress. Uphill mining experiences higher tensile stress than downhill mining. The modeling technique utilized in this analysis presents a first of kind methodology.

Jan 1, 2000

By C. J. H. Brest van Kempen

The techniques developed should provide a useful tool, not only during the initial formulation of a suitable bolting plan for a new section, but also for periodic check¬ing on the utilization factor of hardware installed in the roof. Indications are that with present practice, utilization seldom exceeds 507.. Retro-fittable bolter equipment now available (FCBS?) allows doubling of the utilization factor in many cases. We are also introducing a computer pro¬gram based on the material outlined in this paper. This program can save a great deal of time in examining the real effect of implementing alternate bolting plans or using different installation techniques. It allows fine-tuning of bolt lengths, spacing and installation tension to mini¬mize roof support cost, while maximizing safe life of the mine opening. We have developed a procedure which allows easy, site-specific quantification of the need for reinforcement of a mine roof. The concept is based on the forma¬tion of a direct link between theory and empirical data to custom-fit each mine section. In its simplest form, the proce¬dure requires only recording of roof bolt torques in a sample working place (16 to 25 bolts) several times during the first week or so after initial bolting. The way in which the torque pattern changes during this time can reveal whether or not the bolts carry enough tension to maintain stability in that specific roof. From the same data, the nature of the anchorage horizon is derived. Specifically, shale or limestone can be distinguished from sandstone. If the procedure is repeated a few times (within the same mine section) with different bolt installation tensions, we can numerically characterize the roof in terms of one single value: an "effective angle of internal friction". This number can then serve to calculate trade-offs in bolting plan design, such as bolt length, bolt spacing and optimum bolt tension. Additional refinement is possible if a sagmeter is installed in the sample work¬ing place being monitored and if bolt anchorage capacity is determined. The lat¬ter can be done automatically on each bolt as it is being installed, using a system we developed and patented. Alternately, a number of pull tests could be performed. Using the sagmeter, bolt torque and anchor¬age data, it is possible to project the safe life of the supported opening. The details of the procedures described apply specifically to tensioned roof bolting, but a brief discussion paints the way for a similar analysis of full-column resin bolting also.

Jan 1, 1986

By Jeffrey K. Whyatt

Estimation of the initial vertical stress carried in a coal seam is an important first step in virtually all methods of evaluating the required size of pillars in coal mines. Such estimates are a trivial exercise in coal fields overlain by gently undulating topography. The LaModel program is easily and routinely applied in such cases to efficiently estimate mining-induced stresses throughout the coal seam. However, application of LaModel to coal mines operating under rugged topography and/or in tectonically disturbed regions is more difficult. LaModel estimates stresses in a twostep process. Topographic and multi-seam mining effects on insitu stresses are estimated in an initial step, and then mininginduced stresses are estimated in an independent second step. A LaModel program function has recently been introduced that decouples these two steps, allowing in-situ stresses to be directly entered from a file rather than calculated. One application of this function is to streamline sensitivity studies by avoiding repeated recalculation of in-situ stress. The function also allows importation of in-situ stress estimates developed by other means. There are no constraints on the imported stress field, which may include significant stress perturbations due to topography, faults, etc. Hence, the range of geologic environments that can be examined by LaModel is significantly increased. This study uses the new decoupling function in an exploration of in-situ stress estimation in mountainous terrain. One option is to use the topographic stress estimation feature included within the LaModel program, and the influence of important parameters in this routine is explored. Another option explored is importation of results from a detailed volume element model. Results of this study suggest that the method used to estimate in-situ stress, and the details of its execution, can have a significant impact for mines in mountainous terrain with strong overburden. More generally, decoupling is an efficient and flexible function that should be considered for most design studies.

Jan 1, 2011

By Al Campoli

One of the critical variables affecting resin bolt performance is the size of the resin annulus, defined as the difference between the hole and bolt radius. The vast majority of the millions of resin roof bolts installed each year in the United States employ an annulus between 0.125 and 0.188 inch. As the annulus size decreases the resin flow around the bolt becomes more difficult, increasing the resin pressure induced by bolt insertion. As the resin pressure increases the loss of resin into bedding planes and vertical fractures in the rock increases. As the annulus size increases the mixing of the resin paste and mastic becomes less efficient. Thus, the lower and upper limits of the optimum annulus size is determined by insertion pressure and mixing considerations, respectively. Previous U.S. Bureau of Mines researchers have concluded that a 0 125 inch annulus is optimal. However, others have recently reported that a 0.095 inch annulus with special rolled deformation (SRO) bolts provide superior anchorage to standard rebar with a very large 0.250 inch annulus, attributing SRD resin loss in weak ground to oversized holes. The effect of annulus size on unit length pull strength and resin loss to fractured rock was investigated. Short encapsulation pull tests with resin annuluses of 0.125 and 0.095 inch resisted an average of 2.25 tons per grouted inch, with no significant variation. However, annulus size has shown a dramatic effect on the magnitude of resin lost to simulated rock fractures. No. 5 standard . No. 6 standard, and No 7 J-Bar rebar were inserted into two different viscosity resin cartridges designed for 4 foot boll encapsulation into a one inch inside diameter metal tube, To simulate a rock fracture, a 0.250 inch diameter orifice was located near the capped end of the tube Resin loses increased as annulus size decreased, with a minimum loss of 35% and a maximum loss of 60% associated with 0.125 and 0.095 inch annuluses, respectively.

Jan 1, 1999

By Vladimir I. Klishin

Complex method of ruling of rock pressure is considered in conditions of rapid roof subsidence. The purpose of this method is elaboration of emergency devices into hydraulic props. Also method of unloading of solid roofs is worked out. An analysis of means of protecting hydraulic props of powered supports 6om dynamic loads made it possible to divide them into four classes according to principle of operation: emergency, operating hm an increase of pressure; emergency damping; emergency, operating according to the "plastic element" principle; inertial emergency, operating hm dynarmc loads. It was established that the overwhelming 'majority of designs of the first three classes of emergency devices (EDs) are based on !mditional approaches, which exhausted their possibiiities of high-speed response. Delay on their opening is caused mainly by inertia of the moving locking parts. In our opinion, the most prospective are EDs using the inertia of the moving locking parts for depressurizing the piston cavity of the hydraulic prop with a minimum delay (inertial EDs). The essence of the designs of EDs having an inertial principle of action is that into the hydraulic prop containing movable and immovable elements is additionally introduced a spring-operated contracting support, which is installed on the movable element. Under dynamic loading of such a hydraulic prop hm the roof, the support moves relative to the movable element, performing the role of an inertial mass, which leads to instantaneous depresswization of the piston cavity of the hydraulic prop. Technological measures for unloading of solid roofs consists in creating of long oriented cracks in rock massif. Description of method for creating cracks, demanding equipment and means for cone01 the progress of splits are included. Also technological schemes for realization of the method of saving underground mines and rock mass are included. The results of experimental realization of this method on the Kuzbass and Poland coal mines are also included.

Jan 1, 1997

By Douglas Morrison

Hardrock mines in Ontario generally operate at between 3,000 and 7,500 ft below surface and generally experience significant rockburst activity below 5,000 ft. Since the introduction of bulk mining techniques around 1980, the safety record of Canadian hardrock mines has improved dramatically. However, the process of improvement was not a smooth one and, in the early years, the number of accidents and fatalities actually increased. One incident in 1984 that resulted in 4 fatalities in Ontario initiated a complete re-examination of mining practice and by the mid 1980s many changes had been introduced, driven by new non-prescriptive mining legislation. These changes affected not only the technical discipline of mining engineering but also the management of operational procedures and, together, they resulted in the significant improvements that have continued to this day. The analysis of the rock-fall related fatalities showed 5 major causes (loose, scaling, installing support, collapse and rockburst) and by the mid 1990s fatalities in all of these categories, except rockbursting, had been eliminated and even then, all these rockburst fatalities occurred in one mine which was closed shortly afterward. This paper discusses both the technical and social reasons for the initial failure and the ultimate success in improving the safety of these mines, with implications for mines in other major mining jurisdictions.

Jan 1, 2003

By André Vervoort

To learn more about the fundamental roof behaviour in South African coal mines, accurate underground measurements of roof deflection were conducted in bord and pillar panels during development and pillar extraction. To conduct these measurements a survey levelling technique was adapted. The overall system reading accuracy was established as being within 0,4 mm on a 15 m sighting distance. The underground sites were modelled and, for a roadway development, similar symmetrical curvatures were calculated by a linear elastic model, as were measured underground. In a pillar extraction panel, a significant amount of bed separation was measured and the roof underwent an a-symmetric movement due to the close presence of the mined out area at one side of the roadway.

Jan 1, 1992