Search Documents

By Deno M. Pappas

The purpose of this U.S. Bureau of Mines study was to determine the material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining. Photographs of actual mine gob were used to approximate particle size gradations of gob material. The gradation curve was shifted down to a laboratory scale, and 20 uniaxial compression tests were conducted on simulated gob material from 3 different rock types. The study found that the nonlinear stress-strain curves obtained from the three materials were similar, and could be represented in terms of moduli as follows: Es = 2.36s + 1,360 (1) Et = 0.00181s2 + 9.33s + 294 (2) where Es = secant modulus, psi Et = tangent modulus, psi and, s = stress level (due to overburden), psi. These curves correlated well with the theoretical solution curves developed by Salamon. Other effects on gob behavior were attributable to these studied factors including void ratio, thickness-to-width shape ratio, and rock compressive strength. The generated equations should provide numerical modelers with a practical means of estimating gob modulus as a function of stress level.

Jan 1, 1993

By David Hill

Over the last decade, Beltana No.1 Mine has generally been Australia?s most productive longwall operation, with a ROM output of 7.2 Mt in YEJ2007. Characteristically favorable roof conditions and low depths of cover resulted in typically high rates of development drivage and longwall retreat. As a consequence of these high rates of development and extraction, there was a continuing focus on recovering and relocating the longwall face as efficiently as possible to minimize associated production delays and operational costs. This paper presents a comprehensive case study of the conventional longwall recoveries (?take-offs?) at the mine, from Longwall 1 to 14. By examining the take-off monitoring data collected over the life of the mine, the key geotechnical issues are demonstrated, including their relationship to the ground behavior experienced and the issues overcome.

Jan 1, 2011

By Donald P. Richards

West Elk Coal Company operates its Mt. Gunnison No. I mine on the western slope of the Rocky Mountains in Western Colorado. The mine is located along the north fork of the Gunnisson River near Somerset, Colorado as shown in Figure 1. The mine is designed for a sustained production of 1.4 million tons per year out of the "F" coal seam in the Mesa Verde formation. The coal seam is nominally 7 feet in thickness and dips at about 3 ½ degrees to the northeast. Mining of the seam is up dip with the entry portals on the north facing slope of Mount Gunnison. The mine is designed as a five entry system with four entries for ventilation and access and one entry for a coal-handling conveyor. The mine entry layout is shown in Figure 2. Initial mine planning began in 1979, with "permitting" complete and construction starting in the fall of 1981. A "turnkey" contract for design and construction of all five parallel mine entry tunnels was awarded by West Elk Coal Company to a Joint Venture of Jenny Engineering Corporation (design and contract management responsibility) and Affholder, Inc. (construction responsibility). The first entry access into the coal seam was completed in the early spring of 1982. The mine has been operating at full service (all five entries) for nearly 3 years.

Jan 1, 1984

By Thomas R. Scotese

A rock mechanics instrumentation and monitoring program was implemented during pillar extraction at Gulf Mineral Resources' Mt. Taylor Mine, the deepest uranium mine in the U.S. Three types of monitoring were employed: (1) drift convergence around stopes (using a portable tube extensometer), (2) stress changes in pillars (using vibrating wire stressmeters in horizontal boreholes), and (3) load changes in haulage ways under stopes (using vibrating wire load cells in jack stands). Results include convergence-time graphs, convergence contour maps, stress-time graphs, a stress increase contour map, load-time graphs, and abutment load limit maps. Major factors influencing results include (1) size of pillars around the extraction area, and (2) presence and orientation of a major fault adjacent to one extraction area. These factors, combined with pillar extraction, produced evidence of load transfer over 120 m from a stope measuring only 55 m x 45 m. Vertical stress increases of 7 to 17 MPa (1000 to 2500 psi) within 60 m of the stope were obtained using the stress- meter manufacturer's method. The fault apparently prevented load transfer in the down-dip direction but increased load transfer in the up-dip direction. Convergence rates of up to 1.3 cm/day (0.5 in/day) were measured at two stations. Instruments were generally reliable despite adverse underground conditions. The instrumentation and monitoring program at Mt. Taylor provided a warning system against ground control problems and a characterization of ground behavior for future development and extraction of pillars. Recommendations are made for future mining and instrumentation practices.

Jan 1, 1984

By Alan Bugden

Goedehoop Colliery produces 8 million tonnes of coal a year, principally from room and pillar mining, and is situated in the Witbank Coalfield in the Republic of South Africa. The mine has a long and successful record of producing export quality coal from the 2,4 and 5 seams at depths ranging from 20 to 100 metres using modem mining equipment. Following a number of fatalities caused by large and unexplained roof falls in roadways and intersections of supported ground, a review of the roof control system at Goedehoop was carried out. This led in turn to a programme of underground measurements and surveys. This included detailed investigation of the roof falls, horizontal stress mapping, stress measurement and short encapsulation pull testing on roofbolts. These investigations led to a number of important conclusions in relation to the state of stress in the ground, the roof failure mechanisms, standard of rootbolt installation and performance of the roofbolt system. As a result of the work Goedehoop Colliery has made a number of substantive changes to the roof control management system at the mine. These include: 1. A recognition of the importance of horizontal stress as the main factor responsible for roof falls. 2 The forward planning of roof support based on known features which cause the stresses to be elevated. 3. The introduction of a more effective roofbolt system, which can be more easily installed to a high standard. 4. A response system based on risk assessment and monitoring roof movement on a routine basis. The paper describes the knowledge acquired, the conclusions drawn, the changes made and progress to date.

Jan 1, 2001

By D. W. Evans

Mine subsidence problems due to coal extraction have occurred in a number of areas throughout the United States. Depending on the local geology, the depth of the mined seam, the type of mining method employed for extraction, and other related factors, subsidence can result in anywhere from slight displacements to a total loss of ground. These conditions can have serious consequences on the health and safety of the people living above the mined areas. A number of methods exist to provide support for the ground overlying mines. All of these methods employ some mechanism for providing additional support to either the roof of the mine or the sides of the pillars. Since failure usually occurs due to overburden stresses which are transmitted to the roof and pillars, these methods employ techniques to counteract stresses induced due to the coal extraction. The applicability of any particular method will depend on the availability of backfill material, the areal extent of the affected area, and of course, the cost. The primary use of coal ash for subsidence control has been as a backfill material for the stabilization of large areas. Large scale backfilling projects for subsidence control have been performed in Rock Springs, Wyoming, Wilkes-Barre and Scranton, Pennsylvania, and in Fairmont, West Virginia. Some of these projects have utilized sand, as well as, coal ash as backfill material. Much of the backfilling work performed in the United States has been done in an effort to control mine subsidence in abandoned mines. South Africa, on the other hand, has used backfilling extensively both for ash disposal and to increase extraction in active mines. The utilization of repetitive fill and mine techniques has resulted in extraction increases of as much as eight percent in shallow mines and as much as twelve percent in deep mines.(1) The coal ash injection system which can be used for backfilling depends largely upon whether the mine voids are dry or submerged. For dry mines, hydraulic or pneumatic conveyance systems can be used, while submerged mines are limited to backfilling by hydraulic methods. The use of coal ash as a backfill material has a number of advantages, such as: 1. Coal ash is available in areas throughout the United States and in many instances is conveniently located near areas requiring backfilling. 2. Coal ash is available in significant quantities since many coals when burned will result in about 15 to 30 percent ash by weight. 3. Coal ash as backfill is, in many instances, the most economical alternative fill material. Due to the costs associated with above ground disposal, power companies will often times give the material away to lower their overall operating expenses. 4. Coal ash is usually pozzolanic in nature, that is, this material results in cementitious bonding within the backfilled matrix of material.

Jan 1, 1982

By Peng Zhang

In previous research, the laminated overburden model from the LaModel program was effectively integrated with Analysis of Retreat Mining Pillar Stability (ARMPS) through ARMPS-like input to create a laboratory version of the new ?ARMPS-LAM? program. This program takes the basic ARMPS geometric input for defining the mining plan and loading condition, and then automatically develops, grids, runs, and analyzes a full LaModel analysis of the mining geometry to output the section stability factor (SF), all without further user input. The initial ARMPS-LAM results were encouraging with a case history classification accuracy of 55% to 71%; however, a few of the input variables that were nominally included in the SF calculation showed independent significance in the classification accuracy. Therefore, in order to further improve the accuracy of the ARMPS-LAM program, an investigation of the SFs calculated by the new ARMPS-LAM program and the ARMPS program is detailed in this paper. The initial results of a linear correlation between the ARMPS-LAM SF and the ARMPS SF showed a strong correlation (R2 = 0.88), with the ARMPS-LAM SF averaging about 8% higher. The difference in SFs between the programs were further investigated, and, ultimately, the results indicated that the laminated overburden model as implemented in ARMPS-LAM distributes relatively more load on the section pillars for depths less than about 1,000 ft and less load for depths more than 1,000 ft. The results of this research highlight the potential for improving the ARMPS-LAM program in the future by implementing a more accurate loading calculation on the section pillars.

Jan 1, 2014

By M Nombe

Based on the analysis of a case study at POWELTON No.2 MINE, it was determined that mine stability problems had occurred due to floor softening. A fireclay (underclay) layer in the immediate floor was softening after coal extraction and failing under pillars load. The thickness of soft floor was considered as the governing factor in the determination of the magnitude of floor displacement. The effect of floor thickness on floor displacement was evaluated by creating seven models that were input into the LAMODEL program. The properties of the soft floor were determined from a bearing capacity test performed in the Mains close to the area where mine stability problems had occurred. Moisture increase was considered in the reduction of floor bearing strength. Various strain-softening properties were allocated to the materials representing the soft floor. The LOW GAP POWELTON No.2 MINE was modeled and LAMODEL program was used to determine stress and convergence on both the coal seam and the fireclay seam. The results of critical stress and convergence obtained from modeling were compared with the actual floor failure area in the mine.

Jan 1, 2002

By I. L. Follington

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.1 Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production, Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required. A mechanism has been postulated for the deformation behaviour of the roof and pillars in a mechanised pillar extraction operation from the continuously monitored data, observational data and results of previous studies. The 7 m wide fenders were observed to yield under abutment stresses before lifting commenced. The stability of these fenders throughout the lifting sequence was considered to be dependant upon the magnitude of their post peak load carrying capability. This is influenced by the post peak stiffness and the extent of roof lowering in the vicinity of the fender. Difficulties with fender extraction occurred where remnant coal left standing in the goaf caused uncaved goat to bridge to the mined fender. Difficulties were also experienced where sub-vertical jointing occurred in the roof of the split reducing it's ability to bridge effectively. Despite the relatively short monitoring period, the potential role and application of continuous monitoring in advancing understanding of the rock mass response to mechanised pillar extraction operations has been demonstrated. This understanding now requires enhancement and shows great potential for aiding the optimisation of mechanised pillar extraction operations.

Jan 1, 1992

By Xicai Gao

With the intensification and expansion of deep coal mining, the surrounding rock stress environment becomes further deteriorated because of the complicated geological environment and powerful mining effect, so the major deformation of roadway appeared frequently. The proportions of floor heave are increasing and , the most serious problem is the floor heave of preparatory workings. The coal seam of Binchang coal area in Shaanxi province is at a depth of 621.6 ~ 817.0 m, the average thickness of the coal seam is 25 m, and the overburden and coal measure strata are the main regional aquifers and are highly permeable. The properties of water-weakening are obvious in the floor strata. The main preparatory workings or chambers were driven in the coal seam. The severe floor heave of the water chamber appeared during early mining and the amount was 180 ~ 910mm, and seriously affected the normal installation and use of the water chamber. Theoretical study and numerical simulation as well as the in-situ measurements were carried out to investigate the deformation and failure characteristic of the surrounding rock with non-support in the floor and the main reasons which caused the floor heave were determined. A new combined support technology was proposed which consists of overcutting, grouting, backfilling and invertedarch and bolt-grouting. The field monitoring showed that the cumulative convergence of the water chamber was 20mm, the maximum convergence speed is 1.2 ~ 2mm/d, the accumulative convergence of two ribs was 36mm and the maximum convergence speed is 2mm/d. The combined support technology will enhance the support intensity between the roof and floor, the two sides of the entry and improve the loading capacity of the floor effectively and the floor heave can be controlled effectively.

Jan 1, 2013

By Lorraine Kent

Mine tunnel support using rockbolts was introduced in UK coal mines over the period 1987- 1992 and is now used in over 70% of all mine tunnels. In every case the reinforcement design has been based on the observational approach. After the initial reinforcement design has been established appropriate action levels are defined for predetermined amounts of movement indicating the onset of instability. If the action levels are exceeded appropriate remedial action is taken usually in the form of additional support or reinforcement to maintain stability. This paper outlines the observational design method as used in UK coal mine tunnels. It discusses the low cost instrumentation which has been developed to monitor roof deformation, dual height telltales, how action levels are defined based on the geotechnical environment and the types of remedial measures typically taken. An alternative approach for dealing with areas of increased deformation involves reacting to early roof movement trends and modifying the support installed at the face of the development accordingly. Installation of additional support at the face of the heading improves ground control in poor geotechnical conditions and has the advantage of potentially reducing later additional support costs. A case study is described to illustrate how 'early' action levels can be incorporated into a roof support plan enabling a flexible roof support strategy. Such a system will be site specific and continued analysis of monitored information will be required to confirm the action levels or to adjust them according to any change in geotechnical environment. More accurate roof deformation monitoring systems, such as the Remote Reading Telltale system recently developed by Rock Mechanics Technology Ltd. (RMT) and currently undergoing Mines Safety and Health Administration (MSHA) approval, are ideally suited to this application. The Remote Reading Telltale system provides accurate mine wide monitoring of roof condition on a surface PC.

Jan 1, 1999

By John Stankus

Seam interaction in multiple seam mining has significant effect on entry stability. The remaining pillar in an old working usually creates a high stress concentration zone while the gob creates a stress release zone. A good panel layout should take advantage of the stress release effect created by old workings. This paper presents two case studies of multiple seam mining. The Jennmar Finite Element Analysis System (JFEA) is utilized to analyze the seam interaction effect and identify the mess concentration and relief zones Panel layouts are designed bad on the results of the finite element analysis Appropriate roof support system are also designed for different seam interaction areas.

Jan 1, 1999

By Murali Gadde

Among different types of ground control problems associated with underground coal mining, those related to in situ stresses are the most common ones affecting the safety and economy of a mining operation. As a result, this has been the focus of many ground control research works done in the last three decades. This paper summarizes a recent work done on in situ stress related ground control issues of underground coal mine development workings. The approach used in this study was three¬-dimensional finite element modeling by an implicit code, ABAQUS/Standard. In the models, roof stability evaluations were made using Hoek-Brown rock mass failure criterion. Influence of the in situ maximum horizontal stress angle on the stability of both entry and intersection was examined to help determine the best development layout orientation. Also, the effect of in situ stress ratios on the stability of development openings was studied. To make the work more general, both 'low' and 'high' in situ stress fields were considered In general, the modeling results indicated that entries oriented in the direction of maximum horizontal stress were in the best condition while those oriented at 90° had the least stability. For intersections, the maximum and the minimum stability were seen at 0°/90° and 45°, respectively. However, under some combinations of input conditions, the best or the worst conditions were noticed at same other orientations as well. Based on these findings, layout design charts were prepared for both entries and intersections. It was also found that the change in ground conditions with change in layout orientation was more significant for 'low' in situ stress fields than for the higher ones. Change in the average safety factor with change in the ratio of in situ maximum horizontal to vertical stress resembled a lognormal distribution curve. However, the effect of the ratio of in situ maximum to minimum horizontal stress lacked such a clear trend for different input combinations considered.

Jan 1, 2004

By Anton Sroka, Antoni Tajdus, Axel Preusse, Krzysztof Tajdus

"In Europe, the magnitude and range of mining deformation predicted on the surface have been, in most cases, determined using methods based on Gauss' influence function (e.g., Knothe's theory, Ruhrkohle method, Stochastic method). The increase in the application of numerical methods (finite element method FEM, finite difference method FDM, etc.) provides an opportunity to offer a different approach in describing mining deformations. However, this phenomenon is very complex, and due to numerical limitations, a two dimensional analysis was made (in plane strain) in most cases. Such 2D models could not accurately describe the mining geometry and geological conditions. The authors of this paper carried out the calculations in 3D models which describe a mining situation and the character of the strata in one Upper Silesian Polish mine. Furthermore, the authors include some tips for three-dimensional modeling.INTRODUCTIONThrough the years, many numerical models have been used to describe a phenomenon of underground mining exploitation influence on the ground surface. However, such rock masses are highly disturbed (cracks, fractures, changes in water conditions, etc.), and it is very difficult to suitably describe, in a mathematical manner, such materials. Therefore, many of the numerical models created have been corrected in various degrees.At first, models widely used to describe the behavior of strata in the region of exploitation appeared as elastic models, where scientests assumed that a whole strata behaved in a linearly elastic manner, according to Hook's law. Those models have been modifed to received suitable VALUES (of settlement and range of subsidence troughs. Scientests created this amongst others: elastic models with contact between the rocks layers (Shippam, 1975; Salamon, Chugh and Yang, 1993), elastic models with no tension (Chrzanowska-Szostak, 1988), and elastic models with a contact on the subsidence limit plane (Tajdus K., Tajdus A., 2005). However, in most cases, those models did not bring the expected results and the differences between shapes of measured and the calculated subsidence trough were substantial."

Jan 1, 2010

By Denise Y. Dixon

The objectives of this study were to (1) document the hydrologic impacts of longwall mining on ground water, (2) identify the factors which affect the extent of dewatering, and (3) develop empirical trends to predict the extent of dewatering and recovery in advance of mining. The study was confined to three mine sites in north-central West Virginia. At each site, available ground water supplies were identified and monitored for dewatering effects and recovery. Mine A, located in Upshur County, West Virginia, has relatively thin overburden (approximately 715-280 feet). At this site domestic water supplies and specially constructed monitoring wells were monitored, continuing with an earlier study done by Cifelli arid Rauch. Most such supplies were completely dewatered over the longwall panel. Some of these wells have shown significant recovery, especially near a stream. Extensive monitoring of two nested piezometer wells revealed that dewatering generally started in advance of undermining in the lowermost monitored overburden zones first and then progressed upwards. Most dewatered wells completed in bedrock have shown no recovery, except. for valley drilled wells located within 100 feet of a Stream. Affected dug wells completed in valley alluvium rend located within 200 feet. of the nearest stream have shown significant recovery. Some wells have partially collapsed following mine subsidence. Mine B, having relatively thick overburden (approximately 585 to 900 feet), is located in Monongalia County, West Virginia. Ground water supply surveys have been conducted there in an attempt to study past dewatering effects. Owners reported Chat several wells were dewatered by longwall mining arid vertical air shafts that preceded longwall mining. Dewatered wells over longwall panels hove shown some recovery within 3 ½ years of mining. Mine C also has relatively thick overburden (approximately 585-900 feet), and is located mostly in Greene County, Pennsylvania. In addition to a survey of domestic water supplies at this site, five specially constructed monitoring wells were tested. The shallow monitoring wells suffered drops in water level due to mining but totally recovered within one day to three weeks after dewatering occurred. However, they did occasionally exhibit partial collapse during mine subsidence. Subsidence fracturing was beneficial in increasing the lateral hydraulic conductivity by a factor of about S to 22 for rock strata located within 124 feet of the surface, indicating enhanced shallow aquifer potential. One deep well suffered both partial dewatering and structural damage, with the state of water recovery bring uncertain. Also, two shallow domestic supplies out of five located over the mine were reportedly dewatered, but this claim could not, be substantiated.

Jan 1, 1988

By K. F. Unrug

A new testing technique for the determination of the rock strength from portable rock tester is proposed. It is a quick and economical method that can determine the rock strength with reasonable accuracy in different conditions. This method is based on the application of portable rock tester working at the principle of forcing steel ball into the rock surface. The correlation between laboratory measured compressive and/or tensile strength and rack tester reading has been determined in terms of the three-controlling parameters: (1). diameter of indentation &'the testing sample, (2). diameter of indentation-on the reference bar, (3). Brine11 hardness number of reference bar.

Jan 1, 1990

By Erdal Unal

In underground mining today, safety and economical aspects demand a better understanding of the rock-mass conditions, particularly for design of underground mine openings excavated in weak and stratified rock mass. The rock mass classification systems, in essence, are empirical approaches utilized during preliminary design stage. These systems have been developed for specific purposes and rock mass types, therefore, direct utilization of the classification systems in their original form, for characterization of complex rock-mass conditions is not always possible. This is probably one of the main reasons why designers continue to originate new systems, or modify and extend the ones already existing. RMR and Q systems, for example, although widely used in mining and tunnelling, can not fully describe the specifications of the weak, stratified and flay bearing rock mass. Consequently, the engineering applications that would be carried out based on original RMR and Q ratings could be inadequate for making design decisions even during the preliminary design stage.

Jan 1, 1990

By Thomas M. Barczak

The decade of the 90's brought an unprecedented increase in the development of innovative technologies to provide more effective and easier to install roof support in underground mines. To facilitate the application of these technologies to improve mine safety. National Institute for Occupational Safety and Health (NIOSH) developed the Support Technology Optimization Program (STOP). STOP is a windows based software program that provides mine operators with a simple and practical tool to make engineering decisions regarding the selection and placement strategy of these various standing roof support technologies. This program includes a complete data base of the support characteristics and loading profiles obtained through safety performance testing of these supports at the NIOSH Safety Structures Testing Laboratory. Support design criteria in the form of the required support load density at a specified convergence can he established from four options: ( 1 ) a data base of measured ground reaction data from various mines or ground behavior information inputted by the user. (2) determination of loading requirements based on a detached roof block or rock failure height. or (3) criteria based on the current roof support system, and (4) arbitrary criteria set the by user. Using these design criteria, the program will determine the installation requirements for a particular support technology that will provide the necessary support load density and convergence control. Optimization routines are also available to determine the most efficient support design for a user specified support installation- In addition to these performance measures. STOP can be used to compare material handling requirements and installation costs. Comparisons among the various support technologies are easily made including graphical analysis of relevant support parameters. This paper describes the STOP and its application to optimize standing secondary roof support systems.

Jan 1, 2000

By Rocky Wu

Rock bursts are one of the greatest challenges to ground control in the mining industry. With increasing mining depth and mining scale, there are more and more industry requirements on yielding rock support. Since 2008, Jennmar has been conducting large scale research and development works to develop a technically reliable and cost-effective yielding rock bolt. This paper introduces a new yielding rock support: the Yield-Lok bolt. The bolt is characterized by the designed yielding ability to produce 150?250 mm (6?10 in) of deflection at 8?10 metric tons (MT) (7.9?9.8 t) loads for every 16.4kJ (12,096 ft lb) energy input. The bolt?s performance characteristics are consistent through multiple and varying amplitude of impacts. In this paper, the design criteria of the bolt and the principle of performance are described; the dynamic testing results are discussed; and the features and application of the bolt are presented.

Jan 1, 2011

By André Vervoort

In coal room and pillar, and pillar extraction panels, the sidewall conditions were investigated based on underground measurements and numerical simulations. Three-dimensional linear elastic models provided a useful and quick prediction of the amount of sidewall spalling. However, more complex constitutive models were required to simulate more accurately the extent of fracturing and its effect on the stress re-distribution. The input parameters of a Mohr-Coulomb model were determined by back-analysis of underground measurements, and the effect of the depth of the workings and the time dependent occcurrence of coal pillar fracturing were analyzed.

Jan 1, 1992