Search Documents

By Ronald C. Severson

Crystals of native gold occur in placer-type deposits. Gold, as a pure metal, is the most malleable metal known; therefore, delicate gold crystal forms should not survive mechanical transport and concentration processes involved in placer formation. To test the hypothesis that the crystalline gold is currently forming in place, two active gold-placer operations and an unmineralized background area in Alaska were examined. At these sites, rock outcrops, soil profiles, and native vegetation were sampled. At one sampling site, the soil was panned and yielded crystalline gold, as well as the more common rounded nuggets. The plants and soils were analyzed for their major, minor, and trace-element contents, especially gold. Two procedures, one a simple demineralized water leach and the other a partial digestion with acetic acid and hydrogen peroxide, were also used to extract gold and various anions from soils. The water-extractable gold ranged from <0.02 to 15.0 ppb Au in the extracting solution. This represents as much as a 104 enrichment in gold over average river water. This extractable gold is probably available to the native vegetation. Gold concentrations in the unashed dry plants from the two placer sites ranged between 0.4 and 106 ppb compared to a background range of <1 to <4 ppb Au. The presence of dissolved organic matter in the soils is thought to be responsible for the dissolution, transportation, and precipitation of gold in these placer soils, and this process is presently active in these soil profiles.

Jan 1, 2013

By Robert M. Lewis

Chemically, mica is a complex silicate of sodium, potassium and aluminum. There are no important uses of mica where the chemical analysis is important, except that in some uses of ground mica, the content of iron oxide present as an impurity must be kept to a very low limit. Muscovite mica is frequently found containing black and red "stain" as a homogeneous part of the books or sheets. In most cases this stain or impurity is magnetite or hematite. Some mica contains impurities deposited by infiltration. This is commonly a red stain, less often brown or white. The best mica is free from all such impurities, and the greater their content, the less value does the mica have.(1) It is because of these undesirable impurities that a large segment of the fine ground mica industry relies on weathered pegmatites and alaskite ores as a source of raw material. The mica concentrates obtained from these ores are relatively clean and require moderate beneficiation to meet color and density specifications. One need only to observe the stained and decrepitated condition of the mica recovered from mica schist to appreciate the challenge that processing this material presents. Despite these adversities there are several advantages to be gained by mining and processing mica schist ores. The mica content of these ores are considerably higher than the pegmatites and alaskite ores now being mined, often containing in excess of forty percent mica. This-higher grade mica feed should promote a lower mining and milling cost with its resulting competative advantage. With more rigid government

Jan 1, 1969

By J. P. P. Silva

Sodium silicate (water glass) is a modifier reagent widely used in flotation with the function of a depressant or dispersant. The interaction between sodium silicate and mineral surfaces is still not well understood. This investigation aimed to illuminate the sodium silicate action mechanism as a depressant in the flotation of the minerals quartz and calcite. The experiments were done with high-purity mineral samples in the particle size range below 147 µm. The microflotation tests in a modified Hallimond tube showed that, in all systems tested, the efficiency of sodium silicate increased with the concentration. At concentrations above 1,500 g/t, almost total depression (96% for calcite and 97% for quartz) was achieved. The variation of sodium silicate modulus did not alter the quartz flotation performance in the presence of amine (150 g/t). The most efficient depression pH range was observed between 5 and 8. Above pH 10, the depressant action of sodium silicate was negligible. The infrared spectra obtained at pH 7 after silicate contact showed the presence of the groups OH and Si-OH, both suggesting that the adsorption of the neutral species Si(OH)4, as well as siloxane groups (Si-O-Si), attributed to adsorption of polymeric species. Sharing electron pairs is the proposed adsorption mechanism between Si(OH)4 and polymeric species and the surface sites (Si-O on quartz and Ca-O on calcite). At pH 11, the electrostatic repulsion prevents the species adsorption, impairing the sodium silicate action.

By Peiwei Xiao, Xiang Li, Biao Li, Haoyu Mao, Nuwen Xu

As an advanced method of rock engineering construction safety monitoring, microseismic monitoring technology can monitor the micro-fracture of rock masses within an effective range, and then perform forecast analysis of rockburst, cracking, falling blocks and other disasters. Although the application of microseismic monitoring technology has become more mature, how to improve its application efficiency remains to be further studied. At present, artificial intelligence has been extensively developed, and the use of intelligent algorithms to improve the efficiency of rockburst forecast can provide a valuable reference for the safe construction of underground engineering. To this end, this paper proposes a microseismic multi-parameter rockburst early warning model based on dynamic Bayesian networks. First, the sensitivity of microseismic source parameters to rockburst forecast is analyzed based on microseismic monitoring data and actual rockburst information of a hydropower station. Second, the main seismic source parameters and their data are selected and imported into a dynamic Bayesian network for learning to obtain the rockburst forecast model. The model is confirmed in its self-validation and K times cross-validation, and the receiver operating characteristic curve of the model is also analyzed, it is found that the area under the curve is close to 1, indicating that the model has good accuracy. Finally, the analysis of the influence strength of the parent and child nodes in the model reveals that the moment magnitude and source scale are the most sensitive parameters, which can be used as an important reference for rockburst forecast.

Apr 26, 2022

By George E. Peacock

Campbell Red Lake Mine is situated at Balmertown, in the Red Lake District of Northwestern Ontario, Canada. This area is some 120 miles north of the Trans Canada Highway and is some 160 miles Northeast of Winnipeg, Manitoba. The majority of our 300 employees live in Balmertown, which is a community of some 1,200 people, situated adjacent to the mine proper. The mine is serviced by a single shaft 4,300 feet deep. There are 27 levels at 150 ft. intervals. Stoping is being carried out down to the 20th level with only preliminary development having been done on the bottom 6 levels. The majority of our mill feed of 825 tons per calendar day comes from above the 10th level. Gold occurs as specks and streaks in bluish-grey to white quartz carbonate veins. It is extremely fine grained and most is invisible to the unaided eye. In addition to Gold the veins carry varying amounts of sulphides such as, Arsenopyrite, Stibnite, Pyrite, Pyrrhotite and Sphalerite. A minor amount of silver occurs as an impurity in the gold. Arsenopyrite is a marker for the gold ore at Campbell. The average grade of the mill feed is 0.7 oz. of gold per ton. The ore is dumped into an underground ore pass that feeds to a jaw crusher on the 20th level that reduces the rock to a maximum size of 4". This material is hoisted by skips to an ore bin in the head frame.

Jan 1, 1975

By Pierre Ollivier, Dominique Morin

A general study of gold refractory arsenopyrite pyrite concentrate bioleaching has been carried out including two continuous bioleach testworks at different sizes, namely one at a laboratory scale with a 100 1 unit at a 2 kg/d dry solid flowrate and the other at a pilot scale at a 100 kg/d dry solid flowrate. Both tests show a 80% bioleaching of arsenopyrite in about four days of treatment and with the same kinetic. Pyrrhotite is attacked at the earlier stage of the bioleaching but pyrite remains unaffected. The weak potential of oxidation associated with the decomposition of arsenopyrite and the abundance of arsenite leads to a high grade of elemental sulfur in the bioresidue which consumes the major part of the cyanide during the gold recovery, furthermore, the arsenite and ferrous produced in solution have to he oxidized to obtain a stable precipitate in the waste products and as outlined in previous works of other authors on this subject the addition of iron to obtain a Fe/As molar ratio at least above 3 is necessary. The agitation equipment used in the pilot unit allowed an optimisation study calculation for scaling-up the design and power requirements of an industrial installation, For the pretreatment of a gold refractory As high-graded concentrate the reagent cost has the greatest part in the operating cost of the biooxidation step due to the necessary retreatment of the biosolution, In that conditions the power cost is quite marginal, actually it is significant for the treatment of pure pyrite.

Jan 1, 1990

By Brenda B. Mehnert

Long-term monitoring is necessary to successfully develop predictive subsidence models. Thus, the Illinois Mine Subsidence Research Program (IMSRP) has documented subsidence over a longwall mine in south-central Illinois throughout a 3-year period. No monitoring results of this duration have been previously published for longwall mining in Illinois. To study the effects of surface subsidence and the rate of subsidence, precise level surveying was conducted at the site two or three times a year. Level surveys were conducted at approximately the same time of year using a WILD NA-2 level with a micrometer. Second-Order, Class-I, closure errors were obtained in each survey. Survey monuments were designed to minimize frost-induced movements. At this particular site in southern Illinois, subsidence over chain pillars and the panel centerline continued 3 years after mining. Since mining in 1988, 6.67 feet of subsidence or 70% of the extracted height has been documented over the panel centerline, with almost 0.30 feet in the last two years. The area over the chain pillars has subsided a total of 1.44 feet, with 0.44 feet occurring within the last 2 years. Monitoring over the chain pillars and at the centerline shows the residual subsidence to be fairly uniform. Monitoring is continuing over both of these areas. Long-term monitoring data can be used to improve evaluation of subsidence effects on land and structures. However, coal companies will time mitigation activities depending on other factors including the threshold of structural damage, type of repair needed, and maintenance of landowner and company relations.

Jan 1, 1986

By A. Bumanis, K. S. Bawa

INTRODUCTION A rail rapid transit system called the "Metro" system is presently under construction in the Nation&apos;s Capital area. The agency responsible for the design and construction of the Metro system is the Washington Metropolitan Area Transit Authority, an independent tristate organization set up under an Act of Congress and financed by federal, state, and local public funds supplemented by revenue bonds. When completed, the Metro system will comprise nearly 100 route miles. About fifteen percent of this mileage is now under construction, while designs for the-remainder are in progress. The system is scheduled for completion in about eight years at a cost of approximately 3 billion dollars. The Metro system will involve nearly all types of construction generally used for rapid rail transit projects. About half of the mileage will be underground, comprising approximately 16 miles of rock tunnels, 10 miles of earth tunnels, and nearly 21 miles of cut-and-cover construction in earth (see Figure 1.). The remaining 51 miles of the system is planned to be constructed on the surface as at-grade or elevated structures. The system includes 86 passenger stations, 53 of which will be underground structures. Twelve of the underground stations will be large size chambers in rock while other underground stations will be constructed in earth as cut-and-cover structures. Thus, about one-fifth of the system will be designed as underground structures, namely tunnels and stations, in rock. Such designs in rock resulted from the existence of bedrock (schistose gneiss) at reasonable depths generally in the north and northwest

Jan 1, 1997

By Gregg Sherry, Bob Gordan

INTRODUCTION This paper report presents the general case history for the construction of the North Outfall Replacement Sewer (NORS) project. A 1982 City of Los Angeles Wastewater Facilities Plan recognized that a 19.3 km (12¬mile) section of the North Outfall Sewer (NOS), from Culver City to the Hyperion Treatment Plant, was deteriorating and had insufficient capacity. Built in the 1920s of unreinforced concrete and lined with vitreous clay tiles, the originally unventilated NOS suffered considerable corrosion by H2S gas. This caused roof tile and concrete to fall to the bottom of the pipe, which, over the years, reduced the 11.9 M3/S (420 cubic feet per second (cfs)) design capacity of the NOS to a current level of approximately 8.5 M3/S (300 cfs). This worsening condition, thereby contributing to the polluting of Santa Monica Bay. This situation culminated in the State of California Regional Water Quality Control Board, Los Angeles Region, issuing a Cease and Desist Order on January 27, 1986, which required the City of Los Angeles to eliminate such dry weather overflows through a number of prescribed actions. One of these was to construct the North Outfall Replacement Sewer (NORS) by April 1, 1993. PROJECT DESCRIPTION The NORS Project involved the construction of over eight miles of tunnel and related structures. It consisted of a main tunnel conduit to convey sewage to the Hyperion Treatment Plant and four diversion lines connecting the main tunnel to major existing

Jan 1, 1993

By R. A. Pond

Two 6.17 m (20 ft 3 in.) diameter raises, concrete-lined to 5.49 m (18 ft) inside diameter, were completed in 1978 at the Monterey Coal Company Number One Mine near Carlinville, Illinois, by Frontier-Kemper Constructors. These two raises are the largest in cross-section yet completed by full-face upreaming, and the success of this project is expected to increase the application of raise-boring to coal mine shaft construction. WHY 6.17 M (20 FT) DIAMETER ? Raise boring is well accepted in the metal mining industry for a variety of applications, and is gaining in acceptance in the civil works construction industry. The use of raise boring to construct vertical openings for coal mines has not been as widely accepted, even though coal mining requires, per mine, the greatest number of openings to the surface of any underground activity. Several factors have influenced the low utilization of raise boring in coal mining: 1. Coal mine shafts must often be of large diameter to pass the required high volumes of ventilation air at acceptably low water gage pressures. Cross-sectional areas of finished shafts exceeding 23.23 sq m (250 sq ft) are common. 2. The life of ventilation shafts is comparatively long, and the typical sedimentary strata overlying coal seams normally require that the shafts be lined. Shafts on the intake ventilation circuit must have permanent water-tight linings. 3. Unconsolidated overburden at the surface is often thick, and as reaming cannot be safely utilized in unconsolidated material,

Jan 1, 1979

By C. E. Roessler

Uranium and its decay series are associated with phosphate deposits of marine origin. Uranium concentrations are on the order of 100 to 200 ppm in matrix from the Bone Valley formation of Central Florida and about 25% this value in matrix mined from the Hawthorne formation in North Florida. Occupational radiation exposure due to this source has been under study in Florida since the mid 1970&apos;s (Windham, Partridge, Horton 1976; Roessler and Prince 1978). This report is based on findings of an industry-wide scoping survey conducted by the University of Florida during March 1976 through May 1977 and subsequent studies in selected individual facilities. PHOSPHATE MINING OPERATIONS Mining and beneficiation operations are diagramed in Figure 1. At the excavation site, electric powered draglines remove the overburden and expose the phosphate matrix (ore) which is then slurried and pumped to the beneficiation site. At the washer stage of the beneficiation plant, the matrix is subjected to washing and screening. A coarse product, "pebble" is produced and sent to storage piles while the fine fraction is passed through a series of cyclones to remove the clays. The generated clay suspension is sent to settling ponds while the remaining sand-sized fraction is sent to the flotation plant. At the flotation plant, phosphate particles are recovered from the fine sand particles of similar size through several stages of treatment with reagents, agitation and separation of floating and sinking fractions. The high grade concentrate produced is transferred to storage while the sand tailings are discarded. [ ]

Jan 1, 1981

By Lynda T. Holden, Philip L. LeHoux

Barneys Canyon Mine is a 1.8 million t.p.y. gold heap leach operation near Salt Lake City, Utah. The gold recovery plant has been operating since September of 1989. Carbon elution is done at atmospheric pressure with a high temperature caustic solution. No cyanide is used in the process. Operating experience is discussed.

Jan 1, 1990

By John C. Balla

The Spar Lake deposit is located in northwestern Montana, approximately 27 km (17 miles) south of Troy, MT, under Mt. Vernon. The deposit is a stratiform, stratabound copper-silver deposit occurring in the Revett Formation of the Proterozoic Belt Supergroup. Distribution of known sandstone-type deposits in the Revett Formation is shown in Fig. 1.

Jan 1, 1991

By Hisakazu Matsushita, Yoshio Yamaguchi

INTRODUCTION Shinkansen, operating 1,176km between Tokyo and Hakata, transports 340,000 passengers a day. Presently, the 466km Tohoku Shinkansen linking Tokyo and Morioka and the 270km Jyoetsu Shinkansen linking Omiya and Niigata are under construction. It is progressing smoothly and 95% of the civil and architectural construction has already been completed.

Jan 1, 1981

By Peter Kolitsch, Galyn Rippentrop

INTRODUCTION On April 14, 1994, the joint venture of Kiewit Construction Company and Kenny Construction Company was awarded a 76 million dollar contract for the construction of the New Hampshire Avenue Tunnels in Washington D.C. The Notice to Proceed was given on May16, 1994 and scheduled completion is September 1997. This project is one of five contracts for the Mid-City E Line as part of the Washington Metropolitan Area Transit Authority (WMATA)Greenbelt Route. Once completed, the Mid-City E Line subway tunnels will connect service between the U Street-Cardozo and Fort Totten stations (See Figure 1). The New Hampshire Avenue Tunnels project consists of approximately 6800 feet of twin single track subway tunnels, three vertical shafts, associated utility work and comprehensive restoration work. Section E4b involved two methods of tunneling along the project alignment. The first method consisted of the well known soft ground open face shield driven tunnel and the second method consisted of tunnels driven using the New Austrian Tunneling Method (NATM) . The NATM section of twin tunnels begins at the Buchanan Vent Shaft and proceeds approximately 2630 feet under Rock Creek Cemetery, including the Farragut Emergency Access Shaft and connects approximately 390 feet beyond to the existing Fort Totten running tunnels (See Figure 2). Special considerations had to be given to the portion of the tunnel alignment which passed beneath Rock Creek Cemetery. The analyses and subsequent selection of the tunnel support system were based on anticipated geological conditions and the sensitive tunnel alignment. The New Hampshire Avenue Tunnels project was the second soft ground NATM project in Washington D.C. The first, by no coincidence, was completed at the adjacent Fort Totten Station and Running Tunnels Project by Mergentime/Hochtief, AJV. Currently, on a nearby WMATA jobsite, the J.F. Shea Construction Company has started a third NATM soft ground tunnel. Tunnel support systems were studied with respect to three tunneling methods: •A one-pass system consisting of a bolted precast concrete segmental lining •A two-pass system consisting of an unbolted precast concrete segmen

Jan 1, 1997

By Andrew S. Lain

Before you begin mining aggregates in Oklahoma, you must first look at the market and ask these questions: (1) Is there a need for additional aggregate production? (2) Can we produce the aggregate efficiently enough to compete? (3) Is the deposit close enough to the market? If you can answer "yes" to each of these three questions, then you are ready to start the process for mining aggregates in Oklahoma. The first consideration to be made is whether the aggregates produced will need to meet state specifications. If you do not want to meet state durability standards, there are numerous formations you can mine and produce aggregates. We will deal only with the formations that will meet state durability standards. These formations are located in the southern half of Oklahoma and in the Tulsa area. Some of the formations that contain limestone, dolomite, and sandstone that will meet state durability tests are West Springs Creek, Kindblade, McKenzie Hill, Butterly-Royer, and Rush Springs Formations. Granite and rhyolite also are found in Oklahoma and can be used as construction aggregates. Once an area has been identified as having durable material, and drilling has verified its properties, a permit must be secured from the Oklahoma Department of Mines, Oklahoma Department of Environmental Quality, and any other applicable agency before construction of a plant occurs. There are many different brands of crushers available, but all work on one of two crushing principles-either compression breakage or impact breakage. Each type has its application in different industrial-mineral types and the desired end product. A typical small crushing plant would start with a jaw crusher for primary reduction, and then employ one standard cone and one shorthead cone for secondary reduction. One grizzly would be in the circuit with one finished-product screen and three to four finished-product stackers. Natural sands and gravels are found in rivers and old river channels. These too need to be tested to see if spec product can be produced. All of our sand operations have very little gravel; thus, we do not process the gravel. The sand is processed through classifying tanks for gradation.

Jan 1, 1999

By A. Hayatdavoudi, E. Apande

Introduction Troublesome shales have plagued the petroleum industry for more than 50 years. Unstable boreholes have been experienced when drilled into shale formations; sane have been studied almost at the beginning of rotary drilling. A little progress has been made since then, but much is still to be learned. No simple solution exists so far, but good drilling practices combined with good mud practices have been helpful. It is well known that shales in general have a strong affinity for water, and when water is adsorbed, the stability of the shale section of a well is reduced; cohesive strength will be re- bed, properties will be altered and shale will generally expand and/or crumble. The amount of water a shale will adsorb depends on the characteristics of its clay mineral and the ionic concentration of surrounding fluid. Fluid loss and the resulting hydration of an unstable formation can lead to serious downhole problems. The rate of fluid loss depends greatly on the permeability of the deposited cake. In impermeable formations, however, there is no loss of fluid into the formation. As such, shale, because of its very low porosity and almost no permeability, could be termed impermeable. Yet there is strong evidence that shale surfaces are wetted by an invasion of fluid into the formation through microfractures and jointed planes. It is this wetting that causes the shales to swell and slough into the hole, resulting in problems such as increased mud volume and treating costs, bridges and fill-up, stuck pipe, overgauge hole, poor cement jobs and increased cement requirements, and logging and completion difficulties. Drilling operations have been defeated by severe shale problems, resulting in & hole being plugged and abandoned after several weeks of drilling. Shales are we1l known as being difficult and costly to drill. Numerous fishing jobs have plagued drilling operations, and the cost of reaming tight holes ad weighting up the drilling mud to control shale sloughing has been high. The concept of controlling water loss to stop sloughing was introduced in the 1920&apos;s. It was known-then that calcium in fresh water re- strains clay £ran excessive swelling (theory of osmosis) . This reinforced the belief that calcium-based muds such as lime, gypsum and calcium chloride should minimize hydration of clays. Lime muds were then introduced for this purpose and others in the 1930-1940 decade1. They were used for shale inhibition but were not effective. In an attempt to improve them, a special calcium-type mud beam popular during the 1950&apos;s. Hole enlargement continued and they too were considered ineffective. During & early 1960qs, papers were published claiming that shale swelling could be prevented by using high concentrations of chemical thinner called Chrane Lignosulfonate1. This began the era of highly treated lignosulfote muds. Unfortunately, the hole enlargement problem continued. During & mid-1960’s, oil based muds were used for the purpose of inhibition of shales. Not until 1966 did Mondshine2 suggest that the water phase be saturated with calcium chloride. The cost of using oil based mud was considered by most operators not worth the additional hole stability. The potassium chloride-polymer muds were also used in many fields in the United States and western Canada. The use of these muds has been claimed to prevent clay swelling by inhibition and encapsulation in sane areas of western Canada. They are also expensive and their ueneral application is still experimental. To reduce filtrate loss when sloughing shale becomes a problem during drilling is a reasonable practice. This study will investigate the use of cationic organic additives to mud to form a protective barrier between the shale - which are primarily composed of clays - and water that will keep water from entering the microfractures and will also prevent them from hydrating. In so doing, an understanding of modern clay chemistry and & dispersive properties of cationic additives in water based systems will be our most valuable tools. This study will also present and solve a mathematical model for simulating cation transport phenomena in fractured shales using the Framdlich equilibrium adsorption isotherm. The studies will analyze wellbore failure and stability as affected by cationic organic material.

Jan 1, 1986

By G. Swartz, R. J. Brison, R. A. Wyman, J. P. Vandenhoeck, S. E. Khalafalla

Magnetic fluids are commonly composed of ultrafine submicron particles of magnetite (Fe3O4) dispersed in either a kerosene or a water carrier medium with oleic acid as a protective colloid. The unique property of these fluids is that when the magnetic particles are attracted to a magnet the carrier medium moves along with the particles so that the liquid also appears magnetic. The availability of a fluid whose gross behavior changes sharply in a magnetic field without affecting its rheologic characteristics is becoming critical for many technologic applications. About two gener¬ations ago suspensions of relatively large, micron-sized ferromagnetic particles in oil proved useful in clutches, brakes, and dashpots. These were called magnetic clutch materials, and their viscosities were highly dependent upon the applied magnetic field, in contrast to true mag¬netic fluids which retain their fluidic characteristics under all applied fields and field gradients. While the term "ferrofluid" was used by Rosensweig and Kaiser&apos; to designate a magnetic colloid composed of a dispersed magnetic ferrous material, the more general term, "mag¬netic fluid," is preferred. This is because these fluids may contain ferro- or ferrimagnetic substances, such as cobalt, nickel, gadolinium, dysprosium, or magnetic ferrites in carrier liquids, such as hydrocar¬bons (kerosene), silicones, water, fluorocarbons, etc. Preparation of Magnetic Fluids Magnetic fluids were first prepared by Papell and Faber, at the NASA Lewis Research Center, Cleveland, Ohio, by tumbling ferrite materials for several weeks in a carrier medium (such as kerosene) and a dispersing agent (such as oleic acid) with steel balls. Rosensweig et al.1 compared the stability of their ferrofluids obtained from both metallic iron and the magnetic oxides of iron, Fe3O4 and yFe2O3. They found that, although the saturation magnetization of iron is 3.5 times greater than that of magnetite, its colloidal solutions deterio¬rated much more rapidly. The iron particles were undoubtedly rapidly oxidized to a nonmagnetic state due to the enormous surface area of these colloidal particles. Because the properties of these fluids are highly dependent on particle size and may acquire opposite characteristics by small incre¬ments in that size, more controllable methods of preparation have been developed recently by Khalafalla and Reimers.6 In one method metastabilized pyrophoric wiistite is ground to colloidal size in a kerosene oleic acid mixture, and then it is disproportionated to colloi¬dal magnetite and iron at temperatures just below the eutectoidal temperature of wüstite stability (570°C); thus, t < 570°C 4 FeO t > 570°C Fe + Fe30, (1) Because of its antiferromagnetic characteristics, the precursor wüstite is much easier to grind than magnetite. Another method3 avoids grinding entirely and utilizes a peptiza¬tion technique from ferrous materials in the molecular state of aggrega¬tion. This latter procedure has resulted in preparation of strong fluids at considerable savings in cost.

Jan 1, 1985

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

6.1 INTRODUCTION A surface structure will suffer damage when the additional stresses induced by ground deformations associated with surface subsidence, plus the original stress introduced by construction de¬sign, exceed the strength of the structural elements. In this con¬text, there are two methods available for preventing and control¬ling surface structural damage: one is to strengthen the structure and the other is to design the mining operations such that ground deformations at the structure site can be reduced to an acceptable level. Mining operations include panel layout and mining tech¬niques. These methods are detailed in this chapter. It must be noted that most prevention/control methods men¬tioned in this chapter are used in the countries where the reference papers are cited. In the United States, the coal operators are not required to take those measures mentioned in this chapter. Some of the methods described in this chapter cannot be implemented with¬out changes in the current mining practice as permitted by laws. In addition cost of implementing those methods are not considered here. 6.2 PANEL LAYOUT As shown in Figs. 2.9, 2.10, and 2.11, permanent ground deformations in a subsidence basin mainly concentrate near the edges of the underground opening, and can be divided into four zones. A structure located in different zones will be subjected to different types and magnitudes of ground deformations. In laying out the panels, Table 5.1 and Figs. 2.9, 2.10, and 2.11 could be taken into consideration. Attempts could be made to avoid placing the structure on a location where the ground deformation to which that structure is sensitive is at its maximum. Therefore rational design of the panel is the simplest way to reduce structural defor¬mations. Panel design involves the determination of panel dimension, panel edge location, direction of face advance, and use of yield chain pillars. A. Panel Dimension Since longwalls in the US employ a multiple-entry system, where rows of chain pillars are left unmined, subsidence over those chain pillars is usually smaller. Therefore, whenever possi¬ble, the panel dimension could be designed such that a major structure or structures are over those unmined chain pillars, be¬tween adjacent panels, or some distance beyond both ends of the panels. At the center of the supercritical final subsidence basin, a structure will not be subjected to any final or permanent ground deformations. In order to create such a condition, the panel width must be such that the structure will be located beyond the major influence zone of the final subsidence basin, the minimum dimen¬sion of which must be: [ ] where L is the width or length of the final mined out gob, t is the width or length of the structure to be protected, h is mining depth and [ ] s is the angle of full subsidence. B. Panel Edge Location Wherever there is a permanent panel edge, there are large ground deformations induced on the surface on both sides of the permanent panel edge. Therefore whenever possible the panel di¬mension should be designed such that the permanent panel edges could be located in the areas with the least impacts. In terms of permanent edge location, it is best to eliminate any permanent panel edge under a structure or groups of structures. If this cannot be done, the panel should be lengthened to reduce the number of permanent panel edges, or narrower multiple panels advancing in the same direction in a staggered manner could be employed. If the structures are located in Zones II and III, the longer dimension of the structure must be parallel to the nearest perma¬nent edge (Fig. 6.1). But in Zone IV, the longer dimension should be tangential to the corner of the permanent panel edge. If the structure is inclined to the permanent panel edge, it will be sub¬jected to twisting and shearing. C. Direction of Face Advance The direction of face advance should be parallel to the long axis of the structure. But if the structure is to be located at or close to the center of the final subsidence basin, the direction of face advance should be perpendicular to the long axis of the structure. Careful choice of the direction of multiple face advance is the most effective way to reduce structural deformation and thus dam¬age. This applies the principle of overlapping and cancellations of ground deformations, due to multiple face advance, at the right time and at the right intensity, e.g., opposing tilts, concave and convex curvatures, tensile and compressive strains are induced simultaneously on the structure to be protected by two or more faces. D. Use of Yield Chain Pillars In US longwall panels there are generally two or three rows of stiff chain pillars between the panels. The combined width of the chain pillars ranges from 100 to 350 ft(30 to 107m). depending on mining depth. In general, surface movement above the chain pil¬lars after the panels on both sides have been extracted is much smaller, as compared to that in panel center. Thus in order to create critical or supercritical width of opening and eliminate sur¬face bumps over the chain pillars, yield chain pillars may be em¬ployed (Jarosz and Karmis, 1986). However if yield pillars are to be used, it must be designed such that it yields totally right after the panels on both sides have been extracted. Unfortunately cur¬rent yield pillar design techniques cannot predict when and how much it will yield. In summary, whenever possible attempts could be made to lay out the panel in such a way that surface structures are located above chain pillars between panels or above solid coal beyond both ends of the panels. In those areas the surface structures will most likely be unaffected, or if affected, the damage is so minor that no remedial measures are necessary. 6.3 CONTROLLED MINING TECHNIQUES Several mining techniques are available for reducing the sur¬face ground deformations of specific types. Regardless of tech-

Jan 1, 1992

By John O. Marsden

Process selection is the systematic development of the optun.m metal extraction route for a particular feed matenal and has two main objectives: (1) to optimize project economics, principally a function of gold recovery, throughput rate and processing costs, and to develop a process that satisfies all of the proct requirements including, for example, political and environmental considerations.

Jan 1, 1992