Search Documents

By Robert W. Bartlett

Heap biooxidation of sulfidic refractory gold ore requires large amounts of oxygen, as shown in Figure 1. Bacteria, Thiobaci/lus ferrooxidans, are donnant at oxygen concentrations below about 3% in air (1 ppm in aqueous solution) because ofmonod kinet­ics. Hence, the maximum possible utilization is only about 75%, and it may be much less than that due to poor air sweep effi­ciency. At the maximum oxygen utilization, an ore containing two percent pyrite requires nearly 100 cubic meters of air per tonne (4,000 cubic feet per ton). The stoichiometric air require­ment to oxidize arsenopyrite is similar to that of pyrite. While the leaching solution percolating through the heap introduces some dissolved oxygen, the amount is insignificant because of the low solubility of oxygen in water, 7 to 8 ppm at atmospheric saturation. There are only three ways to provide oxygen to the heap: either air flow by natural convection, diffusion of oxygen from the surface (through stagnant air in the air-filled void space in the heap), or forced air ventilation of the heap. Each of these processes will be reviewed.

Jan 1, 1996

By Darrell M. Hladun, Linda M. Dufour

The benefits of computer simulation in the design of a refracto­ry gold autoclave facility is discussed. Three computer simula­tion programs used for autoclave design are briefly described in this paper. 1) METS IM® - A Process Simulation Software Package Developed by Proware: Mass and energy balances are conducted around the auto­clave and its ancillary processes. Results from the process simulation define process equipment requirements and are used for establishing operating costs. The p_rocess model integrates various unit operations including grinding, acidu­lation, pressure oxidation, counter-current-decantation, neutralization, cyanide leaching, and carbon-in-pulp or car­bon-in-leach. 2) ALGOR® - Finite Element Analysis (FEA): A computer software program is used in the design and analysis of brick lined pressure vessels, such as autoclave, heater, and flash vessels. This software creates a steady state thermal model, and accurately predicts temperature distribution throughout the entire vessel, including nozzles, which represent regions of high thermal intensity. 3) Compress©: A software package developed by Codeware used for the sizing of pressure vessel components, includ­ing shells, heads and nozzles, according to ASME Boiler and Pressure Vessel Code, Section VIII, Division 1.

Jan 1, 1996

By W. Dresler

Since 1900, smelters have produced in Canada over 10 million tonnes of iron silicate waste slag containing significant quantities of nickel, cobalt and copper. The slag is reduced with aluminum and calcium oxide additions to produce a copper, nickel, and cobalt enriched alloy and an obsidian slag. It was found that the obsidian slag contained very low copper, nickel, and cobalt contents, indeed below 0.06% of each the base metals. These metals have been collected in a type of ferroalloy with up to 1.6% Cu, 2.1% Ni, and 0.7% Co. These alloys can be recycled according to standard procedures in base metal smelters. Surprisingly, the obsidian slag was found to display good cementitious and pozzolanic properties, which is a requirement for cement production. The strength producing properties of the obsidian slag are considered to be exceptional at the 28 day standard test age. In most cases, the obsidian concrete is characterized by significantly greater strengths than control concrete tests and concrete containing fly ash or blast furnace slag. Compressive strength data at 365 days for the obsidian concrete is impressive.

Jan 1, 2003

By D. Sotiropoulos

In the recent years, the mining sector is looking for specific indices, taking into account economic, environmental and social criteria, in order to meet the sustainable development requirements. In the present study traditional and environmental sustainable indices used in the Agios Dimitrios Power Plant, Northern Greece, are compared to those of ESKOM Company, South Africa, taken as reference. These indices are referred to, a) the solid fuels consumption, such as lignite, and, b) the emissions to the atmosphere, such as SO2, NO2 and dust. Last five years data show a remarkable improvement of all indices in the Agios Dimitrios Power Plant. Although the lignite used in this Power Plant is by far of poorer quality than that used by ESKOM - net calorific value 1272 and 4638 kcal/kg, respectively - dust emissions in both Power Plants are similar (52 and 31 g/kWh, respectively). The SO2 and NO2 emissions are very low in Agios Dimitrios compared to those of South Africa, respectively 1.92 and 7.91, and 1.74 and 3.61 g/kWh. This is mainly due to natural desulfurization (by the lignite?s calcium content) and the low NOx burners.

Jan 1, 2003

By J. H. Lalor

The Olympic Dam deposit was discovered in July 1975 with the intersection of 38 m (125 ft) of 1.05% copper in diamond drill hole RD 1. A further eight holes were drilled with only marginal encouragement to November 1976 when RD 10 cored 170 m (558 ft) at 2.12% copper and an economic discovery was confirmed. The discovery of Olympic Dam is an excellent example of the application of broad-scale scientifically based conceptual studies to area selection combined with the backing of an exploration management willing to support its exploration scientists in testing their ideas with stratigraphic drilling. It also illustrates the persistence required in mineral exploration. The project began in 1969-1972 with the development of a conceptual model for the formation of sediment-hosted copper deposits. This model suggested that the alteration of continental-type basaltic rocks could release copper into solution from which it could be concentrated in favorable stratigraphic positions. In mid-1972, this concept was applied to a review of the Proterozoic and Lower Paleozoic rocks in South Australia aimed at defining targets for stratigraphic copper deposits.

Jan 1, 1991

By J. G. Groppo, B. K. Parekh

A series of performance studies were conducted using countercurrent column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia using a 150-mm (6-in.) inside diameter column that was 5.8 m (19 ft) high. Both thickener feed and classifying cyclone overflow with a typical size distribution of 150 µm (100 mesh) X 0 were tested. The percent solids of the column flotation feed varied from 1.5% to 15% while the ash content ranged from about 30% to 60%. The concentrates produced contained 2% to 10% ash with Btu recoveries of nearly 90% using 0.12 to 1.25 kg/t (0.25 to 2.5 lbs per st) fuel oil and 0.12 kg/t (0.25 lbs per st) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from seven different seams are discussed as well as scale-up relationships used to design a full-scale installation presently in operation.

Jan 1, 1991

By Robert Stefanko

The widespread and increasing use of electrical power for mechanized power has made a tremendous impact on the coal mining industry. It is probably the single most important factor influencing the productivity of a coal mine. In fact, as a part of a study of 62 coal mines in Pennsylvania and northern West Virginia, plus information that was obtained from other sources, it was possible to show a direct correlation between the rise in the use of electrical power and mine productivity, Figure 1. This increased power demand has not always been achieved through proper planning and a careful evaluation of all design parameters, many of which are not even recognized. The result has been increasing problems in power distribution and utilization establishing the need for scientific studies including considerable underground measurements. Because the cost of power for ton of coal produced is generally a relatively low value, inadequate attention is paid its distribution and utilization. Furthermore, a poor system of records and a lack of adequate measurements add further to a paucity of statistical evidence that would permit a rational analysis of overall power costs. However, the direct cost figure alone is highly deceptive; of much greater value is the indirect costs associated with the use (or misuse) of electrical power underground. Success in highly mechanized mining correlates directly with equipment utilization. Today's machines have tremendous potential capacities but profits are measured in terms of performance and not potential. Thus the reliability of electric motors is an extremely important factor for consideration and the effects of all parameters should be carefully evaluated. Thus while studies are continuing on the evaluation of primary and secondary mine electrical systems with interesting results, this paper will be limited to reporting on the results of a study of a specific motor application.

Jan 1, 1972

By Rolf Christiansson, Daniel Johansson, Urban Åkeson, Henrik Ittner, Mats Olsson

"This paper presents two recent studies on the extent of blast damage after excavation in crystalline rock. The Swedish Transport Administration and the Swedish Nuclear Fuel and Waste Management Company (SKB) are both under regulations to limit excavation damage during construction of tunnels. SKB is also required to limit the Excavation Damage Zone (EDZ), as this could be a potential flow path for radionuclides in the planned repository for spent nuclear fuel. Presented in this paper are investigations of blast damage from three tunnel sites, a road tunnel, an experimental tunnel in Äspö Hard Rock Laboratory and an underground subway depot. As expected the fractures resulting from the bottom charge are both longer and more frequent then those mapped in the column charge. The results show that the requirement to limit blast damage according to Swedish regulations was fulfilled for the column charge at the three studied sites.1 INTRODUCTION The Swedish Transport Administration (TRV) and The Swedish Nuclear Fuel and Waste Management Company (SKB) have both recently completed studies related the extent of blast damage from modern explosives after excavation. SKB studies focused on blast damage from pumpable emulsion explosives for underground construction (Ittner and Bouvin 2015) and hydraulic connectivity in the EDZ (Ericsson et al. 2015). TRV had a broader focus with different types of explosives including blasting for both road cuts and tunnelling with pumpable emulsion explosives. Investigations by means of geophysics were also conducted (Olsson et al. 2015). High demands on perimeter control and excavation damage is usually required for underground constructions with a long operation time, such as public tunnels for transport or underground repositories for nuclear waste. This paper presents the findings of recent Swedish studies and aims to discuss the topic in a broader context."

Jan 1, 2016

By Ronald E. Yarbrough

As a result of concern for the citizens of the State of Illinois who owned structures above underground mine workings, the Illinois State Legislature passed House Bill 158 in 1978. This bill amends the Illinois lnsurance Code and creates the Mine Subsidence Reinsurance Fund which is an insurance pool that is to receive a state appropriation of $500,000 as "start-up" money. One hundred thousand dollars has been paid to the fund as of October, 1982. The Fund is to return this appropriation to the State and is to remain self-supporting from premiums. The Fund utilized a pre-existing institution, which also was an insurance pool, the "Fair Plan Facility" and its governing Board, consisting primarily of insurance executives, to administer the program. The Mine Subsidence lnsurance Act went into effect October 1, 1979, and the bill provides that property owners in the State of Illinois may purchase up to $50,000 of mine subsidence insurance which is attached to their fire insurance policy. The deductible is normally 2%, but cannot be less than $250 or more than $500. The annual rate structure for residential structures in 1981 for $50,000 coverage is $10 (frame), and $12 (masonry). The rate structure for commercial buildings is based on the value of the building and the rates for $50,000 maximum coverage is adjusted upward. The insurance was mandated by the State Department of lnsurance and rolled onto the insurance policies of the homeowners in 34 counties which had been recognized as having sufficient exposure to subsidence damage to be covered by the Act. One percent or more of the land surface is undermined in each of the 34 counties. In the other counties undermined in the State of Illinois, insurance is available to the homeowner upon request to the private insurance carrier.

Jan 1, 1982

By Dennis Keay, Barbara Schickner, P. L. Longenecker, Glenn J. Philips, Lee Rice, Herman E. Knight, Wayne E. Veneman, B. W. Washington, Robert S. Hess

The outlook for coal continued to improve in 1980, fueling expectations that a long-awaited boom is at hand. The surprising surge in coal exports contributed to the latest wave of optimism. Overseas exports hit 66 Mt in 1980, buoyed by a significant increase in demand for steam coal, up from 1979's 2.3 Mt to 15 Mt in 1980. US coal production rose 6.9% to 750 Mt in 1980 and total coal consumption increased 8.1% to about 725 Mt, due primarily to higher world oil prices and setbacks in the US nuclear power industry. Yet the industry is beset with problems-both internal and external. Although demand for US coal is growing, the industry's excess productive capacity is estimated at over 90 Mt/a. Public utilities, where real increases in coal consumption must come, are still moving slowly, blaming delays on antipollution equipment costs. Coal supplies are uncertain, subject to the vagaries of the UMW. For the sixth time since 1964, the coal industry and UMW failed to renew their labor contract without a national strike, reinforcing the perception held overseas that the US is not a reliable supplier. The expected boom in coal exports will, in part, depend on our ability to assure foreign buyers that US sources are dependable. The US industry is also plagued by inadequate facilities linking mines and consumers: inadequate rail systems, coal ports, and barges, For US producers to be competitive, ports must be expanded, rail lines improved, and harbors dredged to allow 136-kt ships to load coal. The im¬provements will require an enormous commitment and investment. Despite these major problems and unresolved issues, two factors continue to favor an increased reliance on coal as an energy source: abundant US reserves and coal's comparative price advantage. Coal's performance in the 1980s may at last exceed its promise.

Jan 5, 1981

By Gerald L. Finfinger, Michael A. Trevits

Since 1964, the US Bureau of Mines has been conducting a comprehensive program of research on the origin and control of coal bed gas. Several extensive databases have been developed during the work representing information from every major coal producing region in the United States. Gas content measurements have been made on 885 coal samples from 15 states representing 221 coal beds. Records indicate that the range of gas content varies from zero to over 640 ft3 per ton (20 cm3 per gm). During the conduct of the research program, several drilling and completion techniques have been developed or refined to divert and collect coal bed gas before it enters the mine environment. Such techniques include horizontal, cross-measure and vertical boreholes. Samples of gas collected from boreholes drilled under the program indicate that the primary gas constituent is methane which comprises 97 pct, the remaining hydrocarbons make up approximately 0.2 pct. Nitrogen and carbon dioxide account for the majority of the remaining gases at average concentrations of 1 pct each. Surveys have been made on the total daily gas emissions from underground coal mines. In fact, the most recent survey indicates that 180 mines had emissions in excess of 100 Mft3 per day (2.8 Mm3 per day). Furthermore, total mine emissions were in excess of 300 MMft3 per day (8493 Mm3 per day). An analysis of the data showed that there appears to be no relationship between in-place gas content and coal bed gas composition. Furthermore, no correlation was observed between in- place gas content and daily mine emissions. In a general sense, the higher the gas content the higher the relative gas emissions. Perhaps a more direct relationship would be observed if more complete emissions information (including gob gas borehole production) was available.

Jan 1, 1989

By Frank A. Aplan, Barbara J. Arnold

INTRODUCTION Coal flotation is a fine cleaning process usually present in all but the older preparation plants. It is typically used to clean either the -28 mesh (-500 pm) or - 100 mesh (- 150 pm) raw coal fines, and it is the only commonly used preparation method that can effectively recover coal particles finer than, say, -200 mesh (74 pm). To place coal flotation into its proper context, it should be noted that the bulk of the raw coal sent to preparation plants is treated by gravity concentration. On a worldwide basis, from 0 to 40% of the raw feed to a preparation plant is treated by flotation, while in the US only about 10% of the raw coal feed is floated. Roughly, 50% of US preparation plants use flotation to process at least a portion of the raw coal feed, although most of the newer plants incorporate flotation into their flowsheet. Historically, the process has only been used to treat the raw coal fines naturally occurring after mining and a minimal amount of crushing at the preparation plant. This is in sharp contrast to ore flotation where, typically, the entire tonnage is first ground and then floated. As a consequence, of the approximately 500 Mt of raw coal treated by preparation in the US yearly, it is estimated that only about 40 Mt are sent to the flotation circuits (producing -30 Mt of clean product).'O1 This small tonnage compares with about 400 Mt of ores treated annually in the US by flotation. By analogy to ore flotation, where it is an effective, large tonnage, low cost, easy to operate process, its potential in coal preparation should be great. Reasons why it has not achieved a greater potential in coal preparation have been attributed by Aplan 102 to: 1. Indifferent results in removing sulfur and ash. 2. Difficulty in floating low rank and oxidized coals. 3. Inability to make clean separations with the finer sizes. 4.Inability to clean slurries with a high percentage of clay. 5. Problems with water chemistry. 6. Competition with effective, gravity coarse-cleaning methods. 7. Low value of coal historically. 8. Dewatering problems. 9. Transportation and storage problems with coal fines. 10. Marketing problems with coal fines. 11. Inadequate attention to the process in the plant. 12. Inefficient use of capital and operating monies. Inadequate attention to procedures, machines, and processes.

Jan 1, 1991

By B. F. Buie

In South Carolina and Georgia an area about 20 miles wide situated near the inner margin of the Coastal Plain and extending from the vicinity of Columbia, S.C. southwestward about 180 miles to the vicinity of Macon, Georgia is the principal kaolin-producing area of the world. It is especially important as the world's major source of clay used for paper coating. Essentially all of the land known or likely to be productive of quality kaolin in this area is now owned or controlled by producing companies. The least-fully developed portion is that in the vicinity of Wrens, Georgia which has been explored and developed since 1961. For the two decades following the end of world war II, demand for kaolin increased at approximately twice the rate for other industrial minerals. From 1945 to 1965 production increased four-fold. Since 1965 the rate of increase has been less, but the outlook now is that production and demand will double at least once again before the year 2000. A substantial part of this increased demand has come, and will continue to come, from industrial development, especially in the paper industry, outside the United States. The general effect, in addition to a continuing increase in production in the U.S., will be to cause: 1. Intensive research for development of more effective and more economical methods of beneficiation; 2. Concerted research effort to find an economical way of modifying high-viscosity kaolin so that it can be used for paper coating; 3. More active exploration in the U.S. and overseas, especially for deposits to supply the foreign markets; 4. More intensive study of the geological factors responsible for the accumulation of commercial deposits of kaolin; 5. Some modest rise in price, relative to the cost of other industrial minerals. The effect on kaolin producing region of Georgia and South Carolina will be to cause: 1. Working of progressively lower-grade deposits; 2. An increase in the acceptable thickness of overburden; 3. Mining of deposits farther down-dip, the use of which is now inhibited by large volumes of groundwater; 4. Increased threat of invasion of the kaolin in industry's market by substitute materials; 5. A substantial increase in concern over environmental factors; 6. More attention to be paid to the large opportunity offered for mining of silica sand and other co-products.

Jan 1, 1972

By S. G. Malghan, W. H. Moyer

In reference to the section "Excess pyrite," the author discusses difficulties in separating chalcopyrite from pyrite. A technique does exist, and has been used commercially, for the flotation, separation, and recovery, if desired, of both chalcopyrite and pyrite. The method was described in Mining Engineering, March 1966, "An Improved Flotation Method for Cornwall Sulfides." While it was not used on a porphyry copper ore, it was used on a chalcopyrite- pyrite-containing ore and might well have application. Both sulfides, chalcopyrite and pyrite, were floated simultaneously using xanthate as a collector and MIBC frother to produce a cleaned sulfide product. This concentrate was then thickened and conditioned at high solids with aeration and lime to a pH above 12.0 for a period of 1.5 to 2 hr. A supplemental suppressant, such as cyanide, could be used if necessary to sharpen the subsequent separation; however, it was not required at Cornwall. The conditioned sulfides were floated with two stages of cleaning to produce a high- grade chalcopyrite froth product and a pyrite sink product barren in copper. The separation at Cornwall gave a 28.6% Cu grade chalcopyrite product and a pyrite analyzing 0.06% Cu. A desliming step on the raw ore initially used at Cornwall for a period of time was later discontinued. Advantages to be found in using a strong sulfide collector, such as a xanthate, is the rapid flotation it induces and, generally, an ability to float at a coarser grind. A following regrind circuit could be used to give maximum liberation and produce a clean sulfide concentration. The "differential" separation is concerned primarily with grade and with assuring a barren pyrite for maximum recovery.

Jan 1, 1987

By John F. Shea

When tunnel boring machines were first developed, the J. F. Shea Company elected not to use them until some of the bugs were worked out. When we did take the plunge, we learned a great many lessons in tunneling; amongst others, that tunneling with a TBM is more an art than a science. One of the most important factors that contributes to a successful TBM tunnel is the geology. A machine can be designed to handle almost any type of ground; however, if the ground is not uniform, compromises in design must be made to enable the machine to handle the various ground conditions. Even when the geologic formations are well defined, it is still impossible to predict how the formations will react when it is penetrated by a tunnel. This is where the design and performance of a tunnel boring machine runs into trouble. When the reactions are adverse, the contractor is left with three alternatives; park or pull the machine and drive conventional, fight through the formation with no changes, or modify the machine. We have made all three of these choices. The first, on the Tonner Tunnel in Southern California, we encountered an extremely tough sandstone where progress was measured in inches per day. Ultimately, we pulled the machine and drove conventional tunnel. The second, on the Vat Tunnel in Central Utah, another element was added to the geology - water, which we encountered in excess of 1,000 gpm at the heading. It was impossible to adapt the machine to handle this much water, so we have been carrying out a program of grouting ahead of the machine and then driving tunnel with the tunnel boring machine.

Jan 1, 1981

By Eugene A. Lang, William R. Archibald

Early in 1972, Rocky Mountain Energy Company approached MARCONAFLO with a unique request for assistance. They controlled a series of scattered ore deposits in a remote section of Wyoming which had become increasingly valuable despite their relatively small size, great depth and low grade. At the time, MARCONAFLO was in the process of developing a tailings reclaim system which was based on the use of submersible capsules. It appeared that this basic concept might be adapted to slurry uranium ores and pump them to the surface through a bored hole. This presentation will review for you the development of this unique and potentially very important application of MARCONAFLO technology. This first slide (SLIDE 1) depicts the total mining concept envisioned by MARCONAFLO and Rocky Mountain Energy Company. A series of six self-contained mining units would be positioned through boreholes into the ore strata. An oscillating MARCONAJET would direct a high pressure jet stream into the orebody and put it into a slurry which would flow back to a slurry pump. The slurry would then be pumped to the surface and to a collection tank from which it would be transferred to processing. Both the MARCONAJET and the slurry pump would be actuated and controlled by means of a hydraulic power console mounted on the trailer behind the service tower. By means of a high pressure water pump also mounted on the trailer, return water from processing would be delivered to the MARCONAJET to slurry the ore. Tailings would be returned to a backfill unit for redepositing in the mined-out cavities. A drill rig would precede the mining, and it was estimated that this configuration would represent an optimum system for most effective equipment utilization.

Jan 1, 1976

By T. H. Udayashankara

Soil pollution, a very serious environmental problem, has been attracting considerable attention in recent years. It is now generally recognized that land as a component of the environment deserves the same attention and protection as water and air. This recognition has arisen perhaps because of increased incidents of land pollution, the scarcity of land, and increased awareness and concern about long-term effects of land pollution on terrestrial and aquatic eco-systems and on ground water quality. Contamination of land results from a wide range of human activities, including industrial discharge process, disposal of wastewater and agriculture. The environmental impact of exploration, production and refining of crude oil is a major concern in developed and developing countries. Because of the known adverse effects of petroleum hydrocarbons on soil ecology and fertility there has been growing interest in the development of efficient technologies for the remediation of contaminated land, with a view toward making it available for further use. Crude oil is a natural product and as such is susceptible to degradation by naturally occurring micro flora. Bioremediation has become an important method for the restoration of oil-polluted environments. A bench scale study was conducted to evaluate the bioremediation technique in treating soil contaminated with transformer oil. The steps involved in this study are: (1) Preparation of contaminated soil, (2) Extraction of PAHs and PCBs from contaminated soil, (3) Treatment of contaminated soil in slurry batch reactor, and (4) Analysis of PAHs and PCBs by gas chromatography technique. The performance of reactor was assessed by measuring parameters like COD, PAHs and PCBs. The study was con-ducted for six different pulp densities ranging from 20% to 40%. The maximum removal of PAHs and PCBs was observed for 20% pulp density.

Jan 1, 2008

By Igor V. Nazarov

INTRODUCTION Tens of deposits in' coal basins of Western and Eastern Siberia are being open-mined with the technology of overburden rehandling into the mined out space of pits by excavators - draglines. This technology is preferred due to the high productive Russian equipment, comparatively low cost, and relatively small Influence exerted on the environment. The basic tendency of the last decades is the aspiration for enlarging the sphere of the' technology application for development of gentle and steeply dipping seams with the use of blast destruction of overburden and with combined winning of loose alluviums and rock partings. Complex technological schemes with multiple rehandling are widely used. In addition to it, stripping workings, intermediate storage of mineral resources, placing of transport dumps, and engineering construction can be realized with the use of draglines. More than ten of dragline faces are simultaneously exploited in some pits, and the rehandling coefficient ranks from 0.1 to 8. Here, conditions of winning and placing (position of a face and existing dump) are varying in space and time; this leads to the necessity of reconsidering the order for conduction of works (schemes) within the current designing. By now, in order to this, it is required to realize complex engineering calculations by graph-analytical methods and definite experience. The need is available for automatization of this process by creation of the corresponding software. The software is to: • Orient on the active pits and use information on the existing geology, equipment, and situation in mine. • Calculate the existing schemes more operative and on a higher qualitative level to model their development in a pit space with parameter optimization. • Predict situations demanding to change the existing technology for mining operations and recommend optimal technological schemes. METHODOLOGICAL FOUNDATIONS FOR MODELING The problem is not new, it has more than fifty year-old history of creating mathematical models algorithms, and programs in Russia, Ukraine, USA, Canada. Australia and other countries with the developed mining branch. Conventionally, all population of programs can be divided into three groups depending on goal and interval of prediction: • Long-term programs used in designing and intended for substantiation of the nine capacity, selection of mining system, establishment of limits for applying the technology of overburden rehandling. Mid-term programs used in current planning for calculation of technological schemes and certificates of face in active mines.INTRODUCTION Tens of deposits in' coal basins of Western and Eastern Siberia are being open-mined with the technology of overburden rehandling into the mined out space of pits by excavators - draglines. This technology is preferred due to the high productive Russian equipment, comparatively low cost, and relatively small Influence exerted on the environment. The basic tendency of the last decades is the aspiration for enlarging the sphere of the' technology application for development of gentle and steeply dipping seams with the use of blast destruction of overburden and with combined winning of loose alluviums and rock partings. Complex technological schemes with multiple rehandling are widely used. In addition to it, stripping workings, intermediate storage of mineral resources, placing of transport dumps, and engineering construction can be realized with the use of draglines. More than ten of dragline faces are simultaneously exploited in some pits, and the rehandling coefficient ranks from 0.1 to 8. Here, conditions of winning and placing (position of a face and existing dump) are varying in space and time; this leads to the necessity of reconsidering the order for conduction of works (schemes) within the current designing. By now, in order to this, it is required to realize complex engineering calculations by graph-analytical methods and definite experience. The need is available for automatization of this process by creation of the corresponding software. The software is to: • Orient on the active pits and use information on the existing geology, equipment, and situation in mine. • Calculate the existing schemes more operative and on a higher qualitative level to model their development in a pit space with parameter optimization. • Predict situations demanding to change the existing technology for mining operations and recommend optimal technological schemes. METHODOLOGICAL FOUNDATIONS FOR MODELING The problem is not new, it has more than fifty year-old history of creating mathematical models algorithms, and programs in Russia, Ukraine, USA, Canada. Australia and other countries with the developed mining branch. Conventionally, all population of programs can be divided into three groups depending on goal and interval of prediction: • Long-term programs used in designing and intended for substantiation of the nine capacity, selection of mining system, establishment of limits for applying the technology of overburden rehandling. • Mid-term programs used in current planning for calculation of technological schemes and certificates of face in active mines.

Jan 1, 2002

By Walter Keune

Object Modeling Technique. This formal descriptive language makes it possible to formulate requirements in the real world in such a way that they can be implemented in the form of entities (cf. Entity Relationship Model[Che83]) and methods (see Figure 1). The object {Roadway} is graphically depicted by means of the Polygon method.

Jan 1, 1996

In parallel work, the cyanide/silver impregnated activated carbon system was studied for the purpose of developing an alternate cyanide removal system. It was found that free cyanide can be reduced from 20 ppm to below 10 ppb with a fixed bed of silver impregnated activated carbon, since such cyanide removal might be applicable to gold mill effluents, the investigation was extended to the cyanide/gold impregnated activated carbon (GIAC) system. Batch tests were conducted varying the gold content of activated carbon, carbon/CN ratio, stirring speed, pH of the initial solution, and the reaction temperature. The adsorption isotherm of cyanide/gold impregnated activated carbon system was also studied. The results of these batch tests show that the behaviour of the cyanide/GIAC system is very similar to the cyanide/silver impregnated activated carbon system variation of the gold content of the impregnated activated carbon has some influence on the cyanide adsorption rate. The latter is mainly increased, however, by increasing the GIAC/CN ratio. The activation energy was determined to be 3.12 kca1/mole (13.08 kj/mole) and the Au(CN)2 saturation at 194 µ M/g NORIT ROX O.B. The experimental results of reaction temperature and stirring speed show that the adsorption of free cyanide on such activated carbon is controlled by pore diffusion inside the activated carbon particle or by surface reaction. The adsorption isotherm follows the linear model and it is favourable for the cyanide/gold impregnated activated carbon system.

Jan 1, 1994