Search Documents

By Jack E. Fraley, Robert E. Simpson

INTRODUCTION Spokane Mining Research Center (BuMines) is researching sealants for underground coal mines to: 1. Reduce sloughing of shale roofs. 2. Reduce sloughing of coal ribs. 3. Seal block stoppings against air losses. 4. Construct stoppings by spraying over jute cloth or metal lath. 5. Render incombustible in-place polyurethane foam. Originally the work was directed towards reducing sloughing of shale roofs. Many underground coal mines have shale directly over the coal which weathers severely after exposure to the mine atmosphere. Lab investigations(l, 2, 3, 4) have shown that many shales separate into layers when immersed in water or stored in a high relative humidity environment. Upon drying or after removal from high humidity, the shales continue to separate. Underground coal mines become wet in the warmer months from condensation of the ventilating air. Conversely, the mines become dry in the cooler months from evaporation. The mines experience severe shale break-up during the summer and much less break-up during the winter. Figs. 1, 2 and 3 show weathered shale roofs. in underground coal mines. Fig. 4 shows fallen shale on the entry floor. Sealing the shale reduces this sloughing problem.

Jan 1, 1974

By S. K. Kawatra, A. K. Bakshi

Mineral suspensions in water show Newtonian flow properties at low percent solids. However, this changes to a non-Newtonian regime as the pet-cent solids increases. For Newtonian fluids, viscosity is independent of shear rate, hut, for non-Newtonian fluids, viscosity varies with shear rate. Therefore, if the slurry is non-Newtonian, attempting to measure the viscosity at a shear rate different from the shear rate experienced by the fluid within the process is futile. This is especially true for a hydrocyclone, where the rate of shear is different at different points within the hydrocyclone. In this case, it is very important to determine the flow type of the suspension before attempting to establish any correlation between the viscosity and the process efficiency. A new technique to distinguish such changes inflow type was developed. This involves two viscometers: a coaxial cylinder-type viscometer that measures apparent viscosity at low shear rates and a vibrating sphere-type viscometer that measures the apparent viscosity at high shear rates. For each of these instruments, special precautions were taken to allow, for the measurement of the viscosity of rapidly settling mineral suspensions. Because the vibrating sphere viscometer is operated at a much higher shear rate than the rotating viscometer, the two instruments together could determine the shear-rate dependency of the viscosity. Ground silica (80% passing 65 µm) in water was used to prepare slurries at concentrations ranging from 10% to 70% (by weight) solids. The viscosity of each slurry sample was measured simultaneously by both viscometers, and the results were compared. With this technique, it was found that all of the silica-slurry samples tested were in the Newtonian flow regime for up to 70% (by weight) solids. Methocel and Cellosize polymer solutions showed clear non-Newtonian behavior using this technique. This confirmed that non-Newtonian behavior of the silica slurries, if present, would have been detected by this arrangement.

Jan 1, 1997

By Norm Greenwald

The Environmental Protection Agency ("EPA") has been attempting to develop a federal regulatory program for mine waste under Subtitle D of the Resource Conservation and Recovery Act since 1986. Recent regulatory and legislative events are now bringing this goal closer to reality. This paper discusses the mining industry's perspective on a number of the issues currently being addressed at EPA's Policy Dialogue Committee and in Congressionally-sponsored negotiating sessions.

Jan 1, 1992

By Stanley J. Gasior

Most bituminous coal mined near Eastern industrial areas requiring high Btu pipeline gas is caking and therefore unsuitable for fixed-bed pressure gasification by present techniques. If the caking property of such coal can be destroyed the resulting fuel can be gasified in a fixed bed at pressure with steam and oxygen as a preliminary step in making a high-Btu gas. To find a practical way to convert strongly caking coals of granular or small lump size to noncaking fuel was the object of this study. In previous work strongly caking coals of 1/8- to 1-1/2-inch size was converted to a noncaking coal char by treatment in a static bed in about 3 hours [1/]and coal of 18-100 Tyler mesh in a fluidized bed in about 5 minutes.[2/] An inert gas such as `steam, nitrogen, carbon dioxide, or a mixture of all three with a small amount of oxygen was used in both studies. In our work a strongly caking bituminous coal from the Pittsburgh seam of 4-8 Tyler mesh size was converted to a-noncaking form in free-fall in about 2 seconds by dropping it through a countercurrent flow of steam containing 4 to 7 percent oxygen at 1,150°-1,200° F and 300 psig. This method should also be applicable to smaller-sized material.

Jan 1, 1965

By J. Cassells, N. Chrisman, R. Arnold, P. Rusin, L. Quintana

Toxic substances in On solutions can retard biological leaching of sulfide dump ores. On solutions were ana1yzed for metals, organics and chloride and showed inhibitory concentrations of aluminum, manganese and chloride. Inhibition of bacterial activity by the solid fraction of On solution with and without the organic constituents, was evaluated. Bacterial toxicity was evaluated by monitoring bacterial numbers, pH, Eh, and rates of iron oxidation. The On solution solids were toxic at 50% to 60% of their field concentration. Most of the toxicity of the On solution was due to the organic fraction. Different solvent extraction (SX) reagents show varying degrees of inhibition of T. ferrooxidans. Bacterial inhibitory effects of carriers and lixiviants used in the SX plant should be determined so that entrained SX reagents do not retard biological dump leach systems. The reagents used should be the most cost-effective and the least toxic.

Jan 1, 1996

By P. Zhang, D. W. H. Su, M. Van Dyke, H. Dougherty

To provide critical scientific data and engineering guidelines to federal and state regulatory agencies as well as the coal and gas industries, the National Institute for Occupational Safety and Health (NIOSH) initiated a Gas Well Stability Research Program in 2016. This paper summarizes the critical scientific data acquisition, interpretation, and modeling by NIOSH regarding the stability of unconventional shale gas wells influenced by longwall mining. Currently, NIOSH is the only organization in the U.S. conducting such fundamental and impactoriented research, which receives input and collaborations from MSHA, PADEP, WVDMS, OHDNR, the coal industry, and the gas industry. Results from the NIOSH field instrumentation programs—which include surface, subsurface, and underground instrumentation—and the parallel three-dimensional numerical modeling programs indicate that, under shallow and medium covers, the measured horizontal displacements within the abutment pillar are one order of magnitude higher than those measured under deep cover. Casing couplers are found to play an important role in longwall-induced casing deformations. Cementing alternatives are found to have significant impact on longwall-induced casing stresses and deformations. Measured 60-arm caliper logging results are in good agreement with three-dimensional computer simulation results. Engineering guidelines on longwall-induced deformations, casing and cementing alternatives, gas well setback distances, as well as risk assessment strategy are proposed.

Mar 2, 2022

By Charles W. Daugherty, Robert Nyren

The replacement of Boston’s elevated Highway I-93 running north to south through the heart of the city with 8-lane tunneled roadways, coupled with the underground extension of Highway I-90 eastward to Logan Airport, has earned the Central Artery/Tunnel (CA/T) Project the position of the largest infrastructure project in the U.S. today. The gigantic interchange featuring numerous ramps where these two main branches of the Artery intersect required the construction of three huge jacked tunnel boxes that were pushed beneath eight active Amtrak and commuter rail tracks that had to remain undisturbed in spite of poor geology and a minimum of cover between the track beds and the tunnel crowns. Ground freezing was chosen as the method of stabilizing the soil over the tunnels, and it was extended in one area to stabilize the ground at the intersection between the tunnels and an abutting deep cut-and-cover excavation. Because many standard geotechnical instruments consist basically of open standpipes filled with water, it was a major challenge to keep them de-iced and in a condition to provide data on vertical and lateral ground movements. The efforts to do so are herein described.

Jan 1, 2003

By A. D. S. Gillies, Hsin Wei Wu

An evaluation of the use of air cooling power as an index of the thermal environment is discussed. A body temperature prediction -. model based on body temperature tests, a concept linked to a maximum safe body temperature and the predicted fourth hour body temperature which depends on the rate of heat accumulation (heat storage) within the body has been developed and tested. This has led to the conceptual development of a personal response heat stress meter calibrated to the physiology of the personnel within the workplace. The proposed heat stress meter will be able to measure workplace environmental parameters such as air temperature, humidity and air velocity and the user can either select or manually enter other heat stress parameters such as work rate, clothing type and subject's personal response to heat. With a built-in computer program, the meter will calculate the ACP of the workplace, the fourth hour body core temperature expected and the maximum safe working time allowed for a pre- defined limiting body temperature. A brief description of the work required for developing the meter is included. The potential benefits of such instrument to the mining industry are also evaluated.

Jan 1, 1997

By R. G. Bradburn

The events which led to computer control of the grinding circuit at Brenda Mines are described, beginning with mill operating philosophy. High production rates are encouraged so that, despite severe upstream disturbances, a manual control method to meet this philosophy had developed. Unfortunately, due to the time interval between manual control adjustments, losses in production resulted. An analog control method was devised and, although superior to manual control in some situations, was found to suffer from several practical limitations. The data logging capabilities of a control computer seemed warranted. Circuit test- work combined with an analysis of operating data showed that (1) metallurgical personnel, at times could increase production rates by as much as 10 percent over that achieved by grinding operators, (2) the chosen data base required an increase of 2 percent or more to be statistically significant and (3) for a 2 percent increase there would be a significant rate of return of investment in a computer installation, Consequently one grinding circuit was fully instrumented, and a rented control computer was installed by Brenda personnel. Prior to installation, Brenda metallurgical and instrumentation personnel were trained in the use of the computer. An experimental program was devised with short and long term objectives. The short term objective was to develop a practical control strategy which would yield immediate production improvement. This goal has been met as described in this paper. Statistically significant increases in excess of 2 percent have been established. Work is being completed for the permanent installation of computer control on all four grinding circuits at the present time. Long term objectives are (1) off line analysis of the circuit using mathematical models of process units, (2) on line experiments to study alternative contol tactics, and (3) possible expansion of computer facilities to the crushing plant.

Jan 1, 1976

By V. Rajaram

The Parachute Creek Member of the Green River Formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential. A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch Joint Venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 1, 1977

By H. Zhu

Qualitative and interpretative information as obtained from geological and/or geophysical studies, in addition to precise measurement, is incorporated into the estimation process through an indicator variable. The indicator conditioned estimator is formulated as a cokriging and its expression is data value dependent as opposed to that of the traditional kriging estimators. The solution of the dual cokriging system pro-vides simultaneously an estimate of the unknown and an estimate of the conditional probability that the unknown belongs to a specific population or class. Being an unbiased and minimum-error-variance estimator by construction, the indicator conditioned estimator is better in the least square sense than the ordinary kriging estimator because it uses additional information carried by the indicator data.

Jan 1, 1989

By V. G. Medina

The 15 000 t/d La Coipa mine initiated operation in July of 1991. The complex consists of a conventional, open-pit mining operation and a mill employing cyanide leaching with Merrill-Crowe gold and silver recovery. The process plant includes a primary crushing circuit, a 15,000 t (live) covered stockpile, a semi-autogenous mill/ball mill/crusher or SABC grinding circuit, a leach circuit, a belt filtration/washing circuit, a zinc precipitation circuit and a "dry" tailing disposal system. The process plant is described in detail with major design considerations used in the selection of the processes and equipment. The unique methodology employed in the disposal of the filtered tailings is also described.

Jan 1, 1992

By A. J. Jeffery

Heat transfer to a fluid flowing through a rough duct has been shown by many researchers to be a function of surface roughness. The effect of roughness asperities on the duct surface is to turbulate the fluid as it flows through the duct, increasing frictional pressure losses and convective heat transfer rates, and also increasing the surface area per unit length available for heat transfer. These factors combine to increase the total costs to the mine in terms of refrigeration and fan power requirements. A measurement system designed to automate the collection of tunnel roughness information and based on an infra-red timed pulse laser has been developed at the Royal School of Mines in London. The system allows accurate, high resolution digital recordings of tunnel surfaces to be made in two or three dimensions. Software for analysing the data has been written, and the description of a complex surface via single numerical term has been explored. A relationship between the numerically measured surface roughness and the pressure loss of the ventilating air is being investigated with a view to establishing an alternative method of describing tunnel roughness. The paper describes the roughness measuring technique developed and the analytical techniques explored so far.

Jan 1, 1993

By A. M. Johnson, M. A. Cornachione

The west central Upper Peninsula of Michigan contains a large resource of graphitic slate. The slate has potential industrial use as a substitute for shale currently used in the production of portland cement. Some of the unweathered slate, however, has a high concentration of pyritic sulfur that can create emission problems when processed in a kiln. A low-cost method to reduce the sulfur content of the slate through the optimization of pyrite oxidation in a bio-heap leaching operation was investigated. In this study, optimal conditions for the bacterium Thiobacillus ferrooxidans were created to promote pyrite oxidation and, therefore, sulfur removal from the slate. Preliminary lab scale flask tests using crushed and sized slate (-40 + 100 mesh) and T. ferrooxidans bacteria in a sulfuric acid medium resulted in 70% oxidation of pyrite over a one-month period. Subsequent column leaching tests on coarser materials (-3/8+1/4 in.) operated for six months resulted in a maximum reduction of total sum of 75%. These data suggest that bio-heap leaching to remove sulfur from the slate for use as a kiln feed material is viable.

Jan 1, 1995

By W. J. Aitken

The pneumatic conveying of relatively large abrasive materials by dilute-phase conveying techniques has been applied in the underground mining industry for many years especially for backfilling mines and the hoisting of ore, coal, or rock out of the mines. The technique was extensively used in Europe, especially Germany and Britain for backfilling coal mines with rejects from the coal cleaning plants which not only helped to reduce environmental problems on the surface, but offered support to the overlaying strata in the deep underground mines, Similar techniques are being employed in the U.S.A. especially in uranium mines for the disposal of tailings, the main purpose being to extract a larger percentage of the ore from the pillars especially under weak roof conditions. Other than for the backfilling of abandoned mine entries, pneumatic conveying has not been applied in the mining industry in surface applications. In this paper, some consideration is given to three applications for open pit mining which may prove beneficial, namely hoisting coal up the high wall, sealing off auger holes, and stabilizing the high wall when being undercut by a longwall system.

Jan 1, 1981

By Steven McCutcheon

As most of us have learned through prior and often frustrating experience, anyone proposing to construct a new or expanded mining-ore processing facility must first contend with a rather complex array of environmental laws and permitting regulations administered by a number of different Federal, State and local agencies. At our lost count, there were about 55 federal enactments affecting base and precious metals projects. Applicable State and local laws will usually increase that number significantly. The time and costs associated with complying with all these various regulatory programs usually constitutes one of the major areas of uncertainty in the development of a proposed project. There are many in the mining industry who firmly believe that these environmental regulation and permit programs necessarily causes significant delays and increased costs in the development of a project. This belief, unfortunately, is probably a result of a basic misunderstanding of how the environmental permitting and regulatory system actually works.

Jan 1, 1984

By Cal D. Iles

Decreasing ore grades and increasing labor and material costs have seriously eroded the economic vitality of many mining operations. Coupled with global economic stagnation and recession in the early 1980's, these conditions have forced reevaluation of operating strategies and methodologies with the objective of remaining competitive in a world marketplace. A concept offering large potential benefits is hardrock portable crushing and conveying. Implementation of this system at Duval Corporation's Sierrita open pit copper-molybdenum mine (Figure 1) has significantly reduced mining costs, becoming a major part of Sierrita's cost reduction strategy. Located 48 km south of Tucson, Arizona, the 209 000 t/d property has one portable 60x89 gyratory ore-crusher in operation with tentative plans for two additional units.

Jan 1, 1985

By P. A. S. Manning

Eastern Jamaica consists predominantly of non-carbonate rocks reaching elevations of over 2200 m. The area is drained by a well established river network which supplies close to 30% of the sand and gravel used by the building and construction sector. Present high extraction rates and slow rates of replenishment will result in early exhaustion of this source of aggregate. A number of volcanic and carbonate rocks are being examined as a possible source of high quality aggregate which meet the requirements for all types of construction. Preliminary evaluations show a dacitic deposit to be the most suitable source for aggregate use.

Jan 1, 1998

By B. Denby, D. J. McMlarnon

During the ongoing research into the possible applications of Virtual Reality in underground operations, the AIMS Research Unit has developed a user-interface driven program which enables a user to input the geometry of underground mines, and add equipment and working processes in order to produce an accurate simulation of their operation. This paper describes the main features of this system (VR-MINE). Virtual Reality is a field which has grown out of three dimensional computer graphics techniques, and allows a user to move freely around a model held within the computer's memory. Movement around this model is carried out by the use of intuitive peripherals such as joysticks, with the user's view from their position within the model being produced in real time on a computer monitor or other device (such as a headset). This enables a user to interact with any three dimensional model and see the results of their actions immediately. VR-MINE is broken into two separate programs, both running under Microsoft Windows 3.1 or above. The first, the editor, allows the user to develop the mine layout and add equipment and personnel. The mine geometry is considered to be made up of various types of objects, for example a straight roadway segment which can be inclined, a junction roadway segment, and a turning segment. The geometry can then saved into a file to be loaded in by the second program of VR-MINE, the viewer. This generates a real- istic representation of the mine, with undulating floors and walls. It also has the ability to display multiple windows on the mine at the same time, which are arranged interactively. The simulation occurs within this program, with the user traversing the model in real time to examine possible areas of improvement in operations. This paper gives a number of examples of how the AIMS Re- search Unit has applied this technology to a range of underground mining scenarios to improve the safety of workers in the under- ground environment. The application discussed include computer graphics and Virtual Reality systems to training, risk analysis, visualisation, simulation, accident investigation and major hazard planning.

Jan 1, 1996

By R. F. Korcak

There exists a wide array of industrial by-products that can be shown to produce beneficial responses in the soil/plant environment. These materials range from clean coal technology residues produced in the generation of electric power, particularly those high in gypsum, to mineral 'fines' produced by the aggregates and crushed stone industries. A number of these materials will be examined in relation to potential nutritional interactions in soils and crops with emphasis on trace elements. The significance of utilizing these materials in agriculture as a component of sustainable agricultural systems will be discussed.

Jan 1, 1995