Search Documents

By Saurav Kumar, Akshay Kumar, Vinayaka R. Kiragi, M. K. Banerjee, Amar Patnaik, Vinod Kumar

Today’s industrial technology offers to optimize and reutilize the resources available in terms of scum that remains after hot rolling in steel rerolling mills in Rajasthan, India. Vast reserves of low-grade coal exist and tons of mill scale are produced everyday after hot rolling in steel rerolling mills in Rajasthan, India. The present research work aimed to optimize the various parameters of solid-state reduction of mill scale using low-grade coal from Rajasthan, India. This study investigates the effect of reduction temperature (850–950 °C in steps of 50 °C), reduction time (60 to 180 min, in step of 60 min), mill scale size (800– 300 μm), and mill scale to coal ratio (1:1, 1:2 and 1:3) on achievable metallic iron percentage and its metallization. A higher percentage of iron content is obtained at a lower particle size of 300 μm. The structural analysis is carried out on 300 μm mill scales using XRD analysis, which shows the percentage of iron is approximately 63%, and metallization above 80% can be obtained under the reduction temperature at 900 °C for 180 min, for 1:3 ratio (mill scale to coal ratio). The chemical composition of the mill scale is obtained using X-ray fluorescence (XRF), and particle sizes as well as distribution of mill scale are determined by scanning electron microscopy (SEM). The elements present in the mill scale are also verified using EDS, which indicates the presence of a major portion of Fe, followed by Fe2O3, Si, and C, respectively.

Aug 14, 2020

By D. Akers

Many of the trace elements found in coal are associated with mineral matter, making it possible to remove them by physical coal cleaning. As part of work funded by the Electric Power Research Institute, both conventional and advanced coal cleaning processes were found to provide large reductions in the concentration of many trace elements that, if released into the atmosphere, are considered to be potentially toxic or environmentally harmful. Advanced physical cleaning technologies appear to provide greater reductions than conventional technologies. Chemical cleaning processes may also remove many trace elements, possibly including organically-bound elements such as beryllium. Care must be taken in the disposal of coal cleaning plant refuse because oxidation and leaching of this material can create highly acidic leachate and many trace elements are mobile in an acid environment. Laboratory leaching procedures are potentially useful in determining the degree of risk of water contamination by trace elements should an acid environment form.

Jan 1, 1992

By R. Stanevich

Studies by the National Institute for Occupational Safety and Health (NIOSH) and the Bureau of Mines (BOM) have demonstrated that: (1) 90% of diesel particulate is less than one (1) micrometer in aerodynamic diameter; (2) more than 90% of the respirable mass in electric coal mines was greater than one (1) micrometer in aerodynamic diameter; and (3) in coal mines using diesel equipment, average diesel concentrations can represent up to 53% of the MRE respirable coal dust standard. For mines approaching the 2 mg/m3 standard, compliance may be easier to attain by controls directed at diesel exhaust particulate as opposed to coal dust control. First, however, a Simple instrument is needed to measure diesel exhaust particulate concentrations. This paper describes such a sampler, its construction, and use. While results from this sampler are primarily utilized to identify control areas, NIOSH is also using the sampler for estimating worker exposures in epidemiologic studies.

Jan 1, 1988

By N. Ripepi

"The Langmuir model has been widely used for the coal-methane sorption process via an isothermal test. However, even though the temperature-dependent Langmuir model were recognized theoretically and experimentally, the quantitative relationship between the Langmuir’s constants (a & b) and temperature have not been clarified and confirmed by lab test data. This paper collects 158 methane-coal sorption data under different temperatures, which apply the Langmuir model to consider the relationship between Langmuir’s constants (a & b) and temperature (see APPENDIX I). Even though the Langmuir model cannot be used to show the physical state of methane adsorption on coal, it is widely used because of its simplicity and the reasonable explanation of its parameters (a & b). The results from these published isothermal tests confirm that 1) there is no consistent relationship between Langmuir’s constant-a and temperature; 2) the Langmuir model is a temperature-dependent model, and the temperature-dependent feature is mainly shown by the relationship between Langmuir’s constant-b and temperature; 3) The relationship between Langmuir’s constant-b and temperature can be described by both the exponential and linear relationship with dried coal. This paper provides a database for temperature-dependent Langmuir’s model, which can be used for reservoir simulation of coalbed methane reservoir, coal seam degasification modeling for underground coal mines considering the heating effect induced by geotherm and heat injection (via hot water, hot steam, ultrasonic, etc.). INTRODUCTION The isothermal test for gas sorption on coal is one of the fundamental tests in Coalbed Methane (CBM) recovery fields, such as underground coal mine methane degasification, CBM gas-in-place estimation, and carbon dioxide sequestration in un-minable coal seams. Generally, two methods, volumetric and gravimetric, are employed to obtain isothermal data (Bush, A. & Gensterblum, Y., 2012). Based on these two approaches, a series of commercial and self-assembled instruments are built and several calculation methods are used to obtain isothermal data (Bush, A. & Gensterblum, Y., 2012, Gasparik, K., 2014; Goodman, A. L., et al, 2004; Zhang, L., et al, 2013). In the post-processing stage, many models are provided to analyze isothermal data in order to understand the storage mechanism of gas in coal. Common models include the Langmuir model (and its extended forms), the pore-filling model, multilayer adsorption model (BET), and the Gibbs’ model. Among these models, the Langmuir model is the most widely used for its simplicity and functionality. The Langmuir model is expressed as follows:"

Jan 1, 2016

By R. P. Aldis

A wide range of mineral-derived products are required by the electronics industry for it to function. In one form or another, almost all the known elements have been experimented with and tested for various electrical applications. The two major areas for which minerals are used in electronics are as conductors and semiconductors. Conductors provide the means to transport and distribute electricity, while the main application of semiconductors has been to manipulate electricity. Silicon is the most widely recognized semiconductor material, but gallium, indium, and germanium are rated as the most important metals to the semiconductor industry for future and near future technologies.

Jan 1, 1991

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Shrinkage stope mining can be employed in steeply dipping veins where both the wall and the vein material are sufficiently strong to stand with only minimal ground support. Shrinkage stope mining takes advantage of the swell in volume produced in breaking in-place ore. This expanded volume of ore is allowed to occupy part of the mined-out vein, and in so doing provides ground sup¬port and a working surface for the miners. Only enough of the ore is drawn after each stoping cut to allow work¬ing room. Not until the entire mining block has been broken is the full amount of broken ore drawn from the stope. DEVELOPMENT PRACTICES FOR SHRINKAGE STOPING The vein is developed into stoping blocks, each of which is 76 to 91 m (250 to 300 ft) in length and 61 m (200 ft) between levels. Level development, described later, is either on the vein or parallel to it with crosscuts periodically driven over to the vein. There are usually two exits from each stope. The first entry is a raise at one end driven either conventionally by raise climber, or by a raised borehole. Present practice is that this raise, put in from level to level, is either a 2.1- x 2.1-m (7- x 7-ft) Alimak raise or a 1.2- to 1.8-m (4- to 6-ft) diam borehole. Either raise system will require pro¬visions for an ore chute carried with the stope to the haulage level or the scram drift. At 9- to 12-m (30- to 40-ft) vertical intervals, dogholes are developed from the raise so that when stoping breaks back into these dogholes, timber or steel sets and necessary service facilities can be installed. The second entry to the stope may be either a similar raise at the stope endline, or more economically, a cribbed raise carried with the stope. As previously stated, development of the ore block is achieved by either drifting on the vein or by paralleling the vein with a footwall lateral and then crosscutting over to the vein at specified intervals. In the following discussion, three basic cases are illustrated in Figs. 1, 2, and 3. In Fig. 1, development is in the footwall by a 3- x 3-m (10- x 10-ft) trackless lateral. A heading is also driven on the ore and taken either full width or driven a standard size and slabbed to the vein width. Approxi¬mately 9-m (30-ft) long crosscuts on 7.6-m (25-ft) cen¬ters are driven from the lateral to the vein. For ease in muck handling they are usually put in on a slant rather than at right angles. A single orepass, located off the lateral and in the center of one stope block, can serve not only that stope, but also one on either side, up to a tramming distance of not more than 137 m (450 ft). Raises are put at the stope endlines on 91-m (300-ft) centers. The back of the vein is shot down and just enough broken material is drawn off to permit access for men to work off the broken ore. Development in Fig. 2 progresses by driving a 3- x 3-m (10- x 10-ft) trackless heading on the footwall side of the vein. The ore block is delineated by raises on 91-m (300-ft) centers. Crosscuts are again driven on 7.6-m (25-ft) centers over to the vein. Approximately four rounds are then taken up to the vein and each round is successively belled out so that all the crosscuts (pockets, in this case) connect. In this development, as opposed to that in Fig. 1 where there were no belled

Jan 1, 1982

By S. Frisch

Selenium (Se) in effluent waters has become a significant challenge for a number of industries. Toxicity studies and new reports of occurrence have certainly caused increased scrutiny and actions in the mining industry today (Sandy, DiSante, 2010). While initial activity in addressing selenium-laden waters were conducted in the coal mining industry, today a much broader range of mine types are beginning to search for solutions to selenium treatment of their mining waters, including both hard rock mining operations (gold, nickel, zinc, etc.) and soft rock mining (phosphate, uranium, etc.) Throughout North America, new regulations covering selenium discharge are either in place or being developed. While a number of physical/chemical approaches show promise in selenium treatment, when considering optimal cost and treatment efficacy issues, biological treatment ? particularly fixed-film biological treatment - is reported to be one of the most promising approaches to managing selenium-containing waters. Among biological treatment options, the fluidized bed reactor (FBR) has undergone extensive pilot testing for Se treatment in the last three years, including eight pilot programs, and the first FBR system is now operating at a coal mining site. In all tests, the FBR has been shown to be a highly cost-effective approach to selenium treatment based on its physical and performance characteristics. This is consistent with its history for reaching low levels of treatment in similar service for other oxyanions including perchlorate, nitrate and various metals. With the results from the most recent testing, the technology has been shown to be adaptable to an ever-broadening range of influent water conditions and flow rates, in varying terrains and weather conditions. Selenium occurs in various valence states from -2 to +6 (Sobolewski, 2005). The speciation of selenium plays a critical role in understanding the effectiveness of any approach for removal, especially to low levels. Elemental selenium is insoluble and has little effect on living organisms. Colloidal fractions are known to occur. In aqueous environments such as coal mining runoff, selenium is most often found as the oxygenated anions of selenite (SeO32-, Se4+) and selenate, (SeO42-, Se6+). Selenium is commonly found in mining waters in concentrations ranging from 3 to >12,000 µg/L. The U.S. National Primary Drinking Water Standard MCL is 50 µg/L for selenium (EU 10 µg/L; WHO 40 µg/L). The National Fresh Water Quality Standard is 5 µg/L for selenium. The U.S. Fish and Wildlife Service has recommended that the National Fresh Water Quality Standard be lowered to 2 µg/L to protect fish, waterfowl, and endangered aquatic species. Several states have followed with enforcement actions at these same low levels. In Canada, permits may require stakeholders to monitor levels in water or biota, or to comply with guidelines, at either the National or Provincial levels, which can be as low as 1 or 2 µg/L in surface waters. Treatment of selenium in all mining waters presents a series of challenges. It can be present in relatively dilute concentrations and in streams with variable and often high flow rates. It can be present in many soluble and particulate forms, which may affect process design and treatability. The conditions of influent selenium-containing waters can vary, with issues such as temperature, pH, total dissolved solids and other contaminants affecting the ability to remove selenium selectively and economically. Treatment of selenium often results in the generation of a concentrated by-product requiring disposal, and re-release from residuals can occur. Beyond these issues, the physical environment of a mining operation can offer challenges such as remoteness and harsh and/or cold weather. Currently available selenium treatment technology (Table 1) includes biological treatment and a number of physical-chemical processes ? such as ion exchange, membrane filtration and adsorption ? that vary widely in efficiency and cost. Most treatment options remain either too costly and/or unproven for selenium-containing streams for reasons that include poor removal efficiency, variability in volume and composition of influents, system sizing and logistics considerations, as well as operating requirements.

Feb 23, 2014

By James P. Connell

The Montana Operations of the Anaconda Company constitute an integrated, though geographically separated, non-ferrous metal production complex. The mines are located at Butte and consist of one large open-pit mine, two small underground mines, a precipitation plant for both underground and pit-dump leach water, and the Weed Copper Concentrator. The smelter, located at Anaconda, Montana 25 miles to the west, processes all Butte copper shipments as well as copper materials from both Anaconda and private mines. Copper and zinc are refined at Great Falls, Montana, 165 miles to the north. Other facilities developed over the years include the Anaconda Forest Products Division, the Butte, Anaconda, and Little. Chicago Water Companies, and the Montana Hardware Company. Data processing for these operations has been performed on an IBM 360 Series, Model 30 computer, utilizing a Disc Operating System. This was replaced in September 1970 with a 360 Series, Model 40 128K unit. In addition, some data processing is also done for Anaconda Company operations located at Britannia Beach, British Columbia; Columbia Falls, Montana; Yerington, Nevada; and Twin Buttes and Tuscon, Arizona. The material under discussion in this paper will be concerned primarily with the mining operations at Butte.

Jan 1, 1970

By John D. Nelson

Unprotected uranium mill tailings impoundments can pose a significant risk to nearby inhabitants and the surrounding environment in the event of a prolonged or catastrophic release of contaminants contained in the tailings. As a result of this potential, reclamation plans for such facilities must include engineering designs to protect against disruption of the tailings and the potential release of radioactive materials. The goals for such engineering designs should be to provide overall site stability for long-term periods with no need for planned ongoing maintenance and to provide a repository for the tailings that will not place a burden on future generations. Although the goal is to provide a maintenance-free system that does not require monitoring, it must be recognized that some period of surveillance would be reasonable. The surveillance period could be relatively short and only needs to assure with reasonable confidence that the reclamation scheme that was implemented is functioning adequately. An investigation was conducted by Nelson, Volpe, Wardwell, Schumm and Staub (1983) entitled Design Considerations for Long-Term Stabilization of Uranium Mill Tailings Impoundments (NUREG/CR-3397). This report assesses the degree of confidence with which long-term reclamation plans can be expected to remain effective over specific periods of time, and to assess the additional effort required to extend the design period from one long-term period to a longer one. This paper presents a summary of that investigation and discusses some of the important conclusions.

Jan 1, 1984

By M. A. Bartkoski

Today?s surviving companies are being pushed to a heightened level of excellence due to market changes. Therefore, new business strategies must be explored. This paper offers a sequenced plan to retool, empower, and organize the entire team for a common goal. Integrity Process is an operating system that is very comprehensive and is integrated in every part of the business. It relies on a detailed prevention concept intertwined with accountability that produces individual efficiencies and team effectiveness. Integrity Process focuses on the importance between working from commitment motives versus compliance fears. The results are balanced in priority and truly yield a win-win for the owners, management, workforce, and the community. Integrity Process can and is being used in any industry that is challenged to optimize the relationship between people and process.

Feb 23, 2014

By A. Almeida, D. Castro, K. Ingmarsson, D. Ferreira, R. Tamir

Mine-to-mill improvements can be initiated at any stage, but it is our assertion that drilling accuracy is a practical anchor in any operating mine or quarry for a structured continuous improvement process. This paper will: 1. Define deviations from plan and provide some best practices for maintaining drilling accuracy. 2. Introduce tools and methods to monitor and calculate consequences of accurate versus inaccurate drilling. 3. Demonstrate the use of these tools and methods and their impact on one cost item, the mitigation of oversized material by a hydraulic hammer. 4. Provide recommendations for implementing improvements.

Feb 1, 2023

By T. J. Jr. DeMull, F. G. Miller, J. P. Matoney

For some time a need had existed in the minerals processing field for a relatively efficient separator that would treat high tonnages of particles in the intermediate size range, i.e., those particles too large for froth flotation and too small for conventional gravity-type separa¬tors. Among those devices developed to meet this need are the centrifu¬gal specific gravity separators. These devices employ centrifugal acceleration to assist gravitational acceleration in separating light¬density minerals from heavy-density minerals. In the category of centrifugal specific gravity separators are the heavy-media centrifugal separator and the water-only cyclone. The two major centrifugal heavy-media separators, i.e., the heavy-media cyclone and the DynaWhirlpool, as well as the water-only cyclone, are discussed in terms of: design features, operating variables, operat¬ing data, and flowsheet design criteria. Examples of plant applications are given in the field of coal processing as well as the processing of other minerals such as iron ores, potash, and tin. Finally, the subject of the staging of centrifugal separators and their use in combination with other separators is discussed. PRINCIPLES For coarse sizes of minerals, efficient specific gravity separations have been possible for many years with open-bath vessels using the natural settling velocity or buoyancy of the particles. These bath ves¬sels process ore by utilizing micron-size solid particles suspended in the slurry fed to the separator. The inclusion of these particles in the slurry increases the effective density of the separating fluid to allow particle separations to be made at densities greater than that of water. However, if vessel size is to remain within economical limits, the particles processed in the bath vessel must have high settling rates in a IG gravitational field. Because of this requirement, heavy¬medium bath vessels are usually restricted to processing +V4-in. sizes. To extend efficient specific gravity separation to smaller sizes, the gravitational acceleration of particles is replaced by centrifugal acceleration. The settling of a small particle in a fluid in a centrifugal force field is similar to that found in a static bath except that the acceleration due to gravity, g, is replaced by a centrifugal acceleration where v, is the tangential velocity at radius r: V=kdm(P-P,), V'. (J) µ In more practical terms where the particles settle in a suspension of finer particles comprising the heavy media and with an effective suspension density p" V = kdm' (P P ) . v'. (2) U r To date the most effective use of this principle has been obtained with devices that rotate a liquid or suspension within a stationary enclosure in order to create centrifugal force. Cyclones are the most common devices used for this purpose, because they generate centrifu¬gal forces far greater than the force of gravity and therefore not only have high capacities but can treat finer sizes than bath-type vessels can. The two main types of cyclones used by industry are the heavy-media cyclone and the water-only cyclone. Also quite widely used is the DynaWhirlpool, which, though based on the same princi¬ple, differs in design from the conventional cyclone. HEAVY-MEDIA CENTRIFUGAL SEPARATORS Like the bath vessels, the heavy-media centrifugal separators em¬ploy media composed of micron-size particles suspended in water. However, the centrifugal force generated in these separators accentu¬ates the difference in settling rate between particles of different density and thus makes possible separations of finer size particles than can be treated in bath vessels. The two most common heavy-media centri¬fugal separators are the heavy-media cyclone and the DynaWhirlpool. Heavy-Media Cyclone Although cyclones were originally developed for use as classifiers or thickeners, it was later found that they could also effectively serve as heavy-media separators.63. 64, Design Features Fig. I I is a schematic of a typical cyclone developed to serve for any one of the following purposes: as a classifier, thickener, or specific gravity separator. The cyclone consists of a cylindrical section joined to a conical section, usually having an included angle of between 14° and 25°. Feed enters the cyclone tangentially through an orifice attached to the cylindrical section. The overflow orifice is located in the base plate of the cylindrical section. The vortex finder, a tube attached to the overflow orifice, extends into the cyclone from the base plate of the cylindrical section. The underflow orifice is located at the apex of the conical section. As some medium together with mineral particles is fed through the feed orifice, a vortex with a hollow air core extending from the overflow to the underflow orifice forms in the cyclone while hollow spray discharges form at each of these orifices. Under the influence of the centrifugal force, high specific-gravity particles move through the medium to the wall of the cyclone and descend in a spiral flow pattern to the underflow orifice. Those particles in the feed stream, lower in specific gravity than the feed medium, follow the major portion of the flow to the center of the core where they are caught in the high-velocity upward central current and are carried out through the overflow orifice. Fig. 12 shows a family of curves that illustrates how materials of varying specific gravity are recovered by a cyclone. Since the specific gravity of the medium is 1.40, the particles of 1.40 sp gr actually act as part of the medium and, regardless of the particle size, split between the underflow and overflow of the cyclone in proportion to the volume split of the medium. Particles higher in specific gravity than 1.40 are recovered in the underflow of the cyclone at increasing rates as the difference in specific gravity increases and the particle size increases. Particles lower than 1.40 in specific gravity are dis¬charged through the overflow orifice at increasing rates as the specific¬gravity difference increases and the particle size increases. However, all the curves originate at the fluid-flow ratio point for the finest particles of any gravity. The fluid-flow ratio is defined as the ratio of the rate of fluid flowing from the underflow to the rate of fluid

Jan 1, 1985

By Carl Heising

Longwall workings in the Federal Republic of Germany are situated in deep depths. Coal deposits are characterized by a sequence of many seams and manifold geological disturbances. Hence result special requirements on the layout of workings, the methods of coal getting, supports, mine ventilation and dust control. As for the application of dust control the large quantities of fresh air and, this, the high air velocity and the limited water contents in the run-of--mine coal must be taken into consideration. The principle of our methods of dust control is to avoid, if at all possible, the development of dust and, if this is not possible, to suppress the dust even during its development. In nearly all coal faces, the method of water infusion prescribed by our Mines Inspectorates is applied. Continuous water in- fusion is preferred. For water infusion in the coal face, intensive developments as to the process and as to the tools and apparates to be applied were done. The German coal mining industry differs between cutting coal getting and stripping coal getting. Water spraying to the tracks of coal ploughs as well as internal and external water feed to the loader required special activities of further development in past years. There are possibilities to still improve such methods in future. A new important field of applying dust control developed from the application of powered supports. In this field, water spraying prevails. Wet methods of dust control are prefered also in the conveying and loading of coal and at through-flow crushers, however, as far as possible, combined with a covering of the working points where dust develops. Devices for the collection and sedimentation of dust, so-called dust exhausters, are used also with crushers In advanced headings, dust control is performed solely by water. Gateroads kept on or behind the coal face line call for new methods of dust control which are at present under development.

Jan 1, 1980

By Andrew P. Gize

A petrographic approach to studying the organic matter in ore deposits is advantageous in that direct observation of sample heterogeneity can be made, organic constituents (macerals) can be identified, and valuable information about the geological history of the sample (such as thermal history, oxidation, and reworking) can be obtained. Thermally immature bitumens are compositionally and structurally heterogeneous, and optically isotropic. The end product of thermal alteration, graphite, is compositionally and structurally homogeneous, and optically an isotropic. One route by which thermally immature bitumens can approach the graphite structure Is by an aromatic intermediate phase, termed mesophase. The development of optical anisotropy and a thermal mesophase has been observed In several high temperature deposits. Textures in bitumens are described from the thermally-altered Mississippi Valley-Type deposit at Nanisivik (Northwest Territories), the silver-vein deposit at Kongsberg (Norway), and the gold deposit at Carlin (Nevada). Textural evidence for multiple generations of bitumens, supportive of a pulsing model for incoming brines, is shown. Petrological evidence for the introduction of bitumens as an immiscible phase or possibly as micelles is shown in the Carlin and Kongsberg deposits.

Jan 1, 2013

By V. K. Srivastava, T. Gupta, T. Ghosh

"In recent years, the demand for rare earth elements (REEs) has grown due to increasing demand and global supply shortage. The supply deficit of these critical elements has encouraged the search for new sources, with coal and coal byproducts as possibilities. Coals from certain parts of the world can be rich in REEs and can approach a total concentration of 1,000 ppm. Two Alaskan coal samples, from Healy and Wishbone Hill, were investigated for the effects of density and particle size on REE concentrations for three selected size fractions, and flotation tests were conducted on finer fractions. Additionally, bottom ash and fly ash samples from a power plant were examined for their REE concentrations. The results show that the upgrade potential for REEs on an ash basis from a whole-coal basis ranges from 2:1 for the Wishbone Hill samples to 4:1 for the Healy coal samples. Flotations of the finer fractions of the two coal samples, conducted under similar conditions, revealed higher concentrations of REEs in the tailings. Both coal samples had comparatively higher contents of light-group rare earth elements (LREEs) than heavy-group rare earth elements (HREEs). REE content trends for the power-plant products on an ash basis indicate that fly ash has slightly higher concentrations of both LREEs and HREEs than bottom ash. IntroductionRare earth elements (REEs), also known as rare earth metals, and their compounds are vital components in industrial, automotive, petrochemical, defense and medical applications. Dysprosium in combination with other elements is used in laser materials and nuclear control applications. Neodymium is present in magnets that are used in the manufacture of wind turbines and hybrid cars. Europium, terbium and yttrium are used in devices that have visual displays such as computer screens and laptops (Haxel, Hedrick and Greta, 2002; Bunzli, 2013). REEs pose fewer environmental problems of disposal and recycling than their conventional heavy metal counterparts (Haxel, Hedrick and Greta, 2002). They are key materials for radar systems, avionics, modern national defense and satellites (Cammarata and Sieradzki, 1994; Hedrick, 2010; Martin, 2010; Szumigala and Werdon, 2011; Cordier, 2011; Bunzli, 2013). REEs are often classified into light-group rare earth elements (LREEs) and heavy-group rare earth elements (HREEs). This classification is primarily based on the electronic configuration in the outermost shell. LREEs, ranging from lanthanum to gadolinium, have a single or no spinning electron in the outermost 4f shell while HREEs, ranging from terbium to lutetium, have paired electrons in the 4f shell. This difference in electronic configuration is responsible for the differences in physical and chemical properties of REEs."

Jan 1, 2017

By Carlos Andrade

An engineering endeavor involves the creation of an expansive, environmentally conscious reinforced sloped MSE wall system. The objective is to enlarge a flat mining work area. Situated in southern Arizona, this mine is dedicated to extracting essential resources such as Manganese, zinc, silver, and lead, crucial for advancing clean and renewable energy initiatives. The project necessitates the implementation of a Mechanically Stabilized Earth retention system. This system aims to both expand the mine’s working area and facilitate access to underground tunnels. The expansion pad must be robust enough to endure the substantial loads exerted by heavy mining machinery. The wall’s reinforcement components are strategically designed to counteract the challenges posed by aggressive soil conditions with low resistivity. Furthermore, they must be resilient against potential damage during installation. The system’s ease of transportation is crucial due to challenging access conditions, and its design must allow for efficient drainage. A significant consideration is the integration of a face system that fosters vegetation growth and seamlessly merges with the existing flora of the area. In addition, plans include the construction of an access road downslope from the wall. The chosen solution involves a reinforced sloped system with a 70-degree incline. The wall’s surface is adorned with an erosion control mat, intended to promote the proliferation of vegetation. For added durability, the wire basket units are equipped with galvanized wire featuring a polymer coating. High tensile strip bonded geogrids, featuring a robust polyester core, provide essential reinforcement. The completed wall is an impressive feat, spanning 1500 feet in length and soaring to a height of 45 feet. It stands as a testament to innovative engineering in harmony with environmental and functional considerations.

Feb 1, 2024

By J. Snowberger III

Rhenium is a valuable and extremely rare chemical element with unique chemical properties. It is extracted commercially as a byproduct from the processing of molybdenite associated with porphyry copper ores. There is a present interest in recovering rhenium from copper pregnant leach solutions (PLS) produced by copper heap and stockpile leaching. These solutions contain rhenium at very dilute concentrations, typically in the 1 mg/L concentration range. This paper describes laboratory column ion exchange experiments to extract rhenium from these solutions using weakly basic anion exchange resins and actual plant PLS from two operating mines. The dynamic loading and elution behavior of Re on Purolite® A170 and A172 is discussed.

Feb 23, 2014

By K. Kim

An analysis was conducted to determine the effects of blasting on slope stability and downstream comminution processes. To investigate these effects, the extent of blast-induced rock damage and the magnitude of induced stress were examined. This analysis showed that damage may extend up to 500 meters (1MPa, tensile strength) in the rock mass, a distance that is sufficient to impact the pit-scale slope over the long term. In addition, the damage zone was calculated using the reasonable assumption that compressive waves are the primary agent in microfracturing during blast fragmentation. The calculated damage zone ? up to 5.6 meters (30MPa, 30% of the compressive strength) ? indicates that microfracturing can occur throughout the entire rock mass in the blasting area. Finally, an economic analysis was conducted by comparing two reasonably assumed blasts in a copper mine. The change in energy required for crushing and grinding was demonstrated using Bond?s law after increasing the blast energy from 180kcal/t to 350kcal/t. A total cost saving of 13.3% ($9.4M) was achieved with the increase. An optimal blast design should consider both slope stability (safety) and downstream comminution energy (production).

Feb 23, 2014

By F. D. Wicks

This paper summarizes the direct operating cash costs for the Barrick Mercur open pit gold mine. A comprehensive, detailed system of cost management has been in effect for the life of the Mercur operation. This system provides the basic data for operations control and is the basis for drafting budgets as well as analyzing impact of change on operations costs. The ore body is complex geologically and metallurgically, requiring operators to pay close attention to mining and processing costs. The cost history provides data which enables analysis of changes in production levels, aging of the mine production fleet, and the impact of specific cost changes through time.

Jan 1, 1993

By John A. Dearinger, Fred D. Wright, Robert C. Howell

INTRODUCTION The rock mechanics study of the shortwall mining system at Beth-Elkhorn corporation's Hendrix No. 22 Mine is being conducted under contract with the U.S. Bureau of Mines. The objective of the study is to obtain data on surface subsidence over a portion of the mined area, strata subsidence in the mined area, and underground stress changes and displacements in and near natural support elements of the mining system. This study is currently in progress, and only a portion of the results are being presented at this time. The Hendrix No. 22 Mine is located in the moderately rough mountainous terrain of Letcher County in eastern Kentucky. The nearest mine workings to the shortwall area are approximately 1,900 feet distant. The depth of cover over the mined shortwall area varies from 770 feet at Panel 1 to 170 feet at Panel 5 (Figure 1). The strata in the shortwall area is summarized in the three core logs shown in Figure 2. Hole no. 2 is located in approximately the center of the mined shortwall area (Panel 3, Line C, Figure 1). The coal seam in the shortwall area is approximately 4 feet thick and horizontal, although one major ‘roll’ intersects all panels.

Jan 1, 1977