Search Documents

By J. L. Vanderbeek

The SAG milling of ores with markedly variable grinding rates presents definite process control challenges. Decisions must be made regarding the selection of the most appropriate combination of mill volumetric load level, percent solids, and mill speed for the combination of ore types being processed at the moment. An investigation was performed concerning the effects of these parameters. General results are presented.

Jan 1, 1985

By Ted D. Johnson

INTRODUCTION The tailing dam is part of the SOHIO L-Bar Uranium Mine and Mill located about 70.8 kilometers (44 miles) west of Albuquerque in northwestern New Mexico. The dam location is shown on Figure 1. The tailing dam is one of the last upstream method dams permitted in the industry. Design and construction aspects of the project, as well as operation and maintenance considerations, are reviewed herein. Since initial construction, SOHIO Western Mining Company and Woodward-Clyde Consultants have developed several modifications and improvements in the dam's operating and monitoring procedures. This work has been done in coordination with the New Mexico State Engineer's Office and in accordance with recommendations in a report done for the Corps of Engineer's Phase I Dam Inspection Report. Modifications and improvements described should be of particular interest to owners and operators of other tailing dams utilizing the upstream method of deposition. The tailing facility was designed for a 10-year life to provide an ultimate storage capacity of 6 1/2 billion kilograms (7 1/2 million short tons) in an area of about 180 acres. A plan view of the tailing dam is shown on Figure 2. The tailing consists of approximately 75% sand size material and 25% fines (material passing the No. 200 sieve). The tailing dam includes a small earth starter dam with raises of the dam accomplished using tailing deposited by upstream method techniques. The starter dam is a homogeneous embankment about 610 meters (2000 feet) long, a maximum height of 12 meters (40 feet) and 2 1/2:1 (horizontal to vertical) upstream and downstream slopes. The starter dam contains an internal drainage system which includes a near vertical chimney drain connected to horizontal finger drains. A typical section through the maximum height of the starter dam is shown on Figure 3. A small confining dam, approximately 1.6 meters (5 feet) high, is constructed beyond the limits

Jan 1, 1980

By J. J. Schwoebel

Resource Enterprises, Inc. (REI) is exploiting the coalbed gas resource by working in unison with active underground mining operations. At REI?s pilot project at the Soldier Canyon Mine, Carbon County, Utah, REI has drilled nearly 15,250 m of horizontal in- seam and slant boreholes during the initial two years of drilling activity. Produced gas has been sold to a natural gas transmission company on a continuous basis since mid 1983.

Jan 1, 1986

By William H. Dresher

The crust of the earth, together with its seas and its atmosphere, is the source of all of mankind's primary wealth. Indeed, most people think of precious metals and stones when they think of wealth mined from the earth, but the value of the material and energy goods derived from the earth far exceed the value of the precious metals and gem stones. Thus, it is obvious that all minerals which we mine from the ground represent new wealth--the copper, clay, or petroleum we mine just as much as the gold or silver. More and more, wealth is defined in terms of utility-not in terms of an arbitrarily established monetary value. The recent action of the OPEC nations in controlling the flow of petroleum has clearly demonstrated this to the petroleum-importing nations! There is developing in the United States, as well as in many other nations of the world, a concern for the future availability of many mineral-derived raw materials and of mineral fuels. Ore grades are diminishing, concern for the environment has placed restraints on commercial development of some mineral deposits and the processing facilities necessary to exploit them, and countries upon which we have relied for major mineral materials have become increasingly nationalistic, causing uncertainties in future supply and causing an increasingly alarming deficit in our nation's balance in trade.

Jan 1, 1980

By Michael J. Humenick

A laboratory experimental research project was conducted to evaluate the use of chlorine for the oxidative destruction of residual ammonia which may remain in ground water after in-situ uranium solution mining operations. The work tested the idea of the injection of high strength calcium hypochlorite solution into the mining zone to convert ammonia to nitrogen gas as a final clean-up process for ammonia removal from the ground water system. The paper details ammonia removal efficiency as a function of chlorine dose, reactant and product material balances, and how the concept may be used as a final ground water restoration process.

Jan 1, 1982

By H. H. Murray

Industrial usage of clays for current and new applications will continue to grow into the next century. The rate of growth will be highest in the less developed areas of the world. Transportation costs are a significant part of the delivered price, so the location of reserves and processing facilities for kaolin, bentonite, and palygorskite (attapulgite) are reviewed relative to serving these emerging markets. New value added applications will increase in the more developed areas which will require high quality raw materials, more sophisticated processing, and rigorous quality control.

Jan 1, 1998

"INTRODUCTION Foam, unless intentionally created, in any industrial process presents operational problems, or at a minimum, is a nuisance. Some foam problems are unique to a given industry and others are common across many industries. A few problems foam presents to any particular industry are: (a) Poor Housekeeping, (b) Environmental impact, (c) Safety Hazards, (d) Slower Production Rates and, (e) Reduced quality of the end product. Defoamers address these issues. Sadly, the assumption in most industries is all defoamers are alike. In reality, a lot of chemistry is involved in the manufacture of even the simplest defoamer sold today and rarely are any two defoamers “just alike”. Today’s defoamers can include polymer chemistry, fatty esters, alkoxylated alcohols, silicone chemistry, silicone surfactants, ethoxylated and propoxylated block polymers, and a tremendous amount of emulsion chemistry just to name a few. This paper will discuss the various types of defoamers, defoaming mechanisms, the advantages and disadvantages of defoamer selections, and how to choose the proper defoamer for your application. Before a discussion of defoamer can be brought about, foam generation and composition must be discussed. WHAT IS FOAM? Foam is a colloidal suspension of a gas dispersed in a liquid. Most often foam consists of air dispersed in water. If a stream of air is introduced into a liquid, the bubbles produced assume a spherical shape. As the density of the bubble is less than the liquid the bubble rises. When the individual bubbles reach and pass through a surfactant free liquid they collapse. Air from the bubble dissipates and the liquid previously surrounding the bubble flows back.It should be noted a pure liquid will not foam. In the case of air dispersed in water a surfactant is necessary to make the water support a stable foam. A surfactant is a term used to describe a surface active agent; a compound with a hydrophilic end and a hydrophobic end on the same molecule."

Jan 1, 2016

By E. T. Pecina

Bioleaching is a viable option for the processing of auriargentiferous refractory ores with high arsenic content. The application of mesophilic (A. ferrooxidans and ?L. ferrooxidans?) and thermophilic bacteria of the genus Sulfolobus (S. solfataricus and S. acidocaldarius) as oxidant treatment before the cyanidation of an industrial arsenical pyrite concentrate is presented. The results show that extraction of gold and silver increases due to bio-oxidation caused by mesophilic bacteria and results in a maximum gold recovery of 68%. In all strains studied, biooxidation resulted in an average silver recovery of 50%. The results showed that all evaluated strains were sensitive to solids content (5 to 20%) and average particle size (75 and 38 µm) of the concentrate.

Jan 1, 2010

By C. Wayne Burnham

Much has been written about hydrothermal alteration and the compositional changes induced by it in the wallrocks of mineral deposits, especially in alummino-silicate wallrocks. So much has been written and the descriptions so varied, in fact, that the casual reader frequently is bewildered by the extreme complexities and lack of uniformity, real or apparent. Certainly the mineralogy and chemistry of altered rocks are not as simple as most of us would like, but neither are they as complex in their principal aspects as pa of what has been written would lead us to believe. The trend until recently seems to have been toward greater complexity and hence greater confusion, but the straightforward presentation of Creasey (1959), it is hoped, marks a reversal in this trend.

Jan 1, 1962

Direct force measurements were conducted using an atomic force microscope (AFM) to study the mechanism of copper-activation of sphalerite. The force measurements were conducted between a sphalerite plate and a hydrophobic glass sphere in xanthate solutions of various pHs. The glass sphere may represent the hydrophobic air bubbles interacting with minerals during flotation. The force measurements conducted with unactivated sphalerite in 10') M KEX solutions did not show the presence of hydrophobic force. On the other hand, the results obtained with copper-activated sphalerite at pH 9.2 and 4.6 showed strong hydrophobic forces. However, the results obtained at pH 6.8 showed no evidence of hydrophobic force, which provides an explanation for the difficulty in floating sphalerite at neutral pH.

Jan 1, 1998

By Christopher D. Henry

Environmental geologic maps of the Wilcox and Jackson-Yegua lignite belts of the Texas Coastal Plain delineate land areas on the basis of their natural characteristics. Criteria used to define map units include substrate, soil, topography, geologic process, vegetation, and land use. The maps are useful in planning and reclamation of lignite mines and in meeting the requirements of State and Federal surface mining laws. Specific applications include identification of land capability, recharge areas and geometry of aquifers, flood-prone areas, areas that may qualify for prime farmland status, and other areas sensitive to lignite mining.

Jan 1, 1982

By L. W. Saperstein

P.J. Ehret By and large, I agree with many of the precepts discussed in the Saperstein paper. I believe there is much more that can be done on the local level to involve both government and planning in the mine permit review process. Admittedly, much can be done to improve discussion between the state regulatory authority, local authorities, and mine operators. However, I strongly disagree, as suggested in the paper's conclusion, that such a system, as outlined in Saperstein's paper, could result in a reduction of review time or a lowering in the cost of permitting. The implementation of such a system by its very nature would only add a new level of bureaucracy to an already cumbersome process. This system, in my opinion, would only add to the cost of permitting and the time necessary to obtain a permit. Admittedly, it would achieve the result of adding local influence into the permitting process, but at what off-setting cost? It has been my professional first-hand experience and observation in the permitting and lands unsuitable processes to note that under the present system, local governments that do feel they have a stake in local mines and actively ad¬vocate their position (not simply comment), have had significant input into the conduct of mining and reclamation plans in their areas. Mining companies that mine in these areas are aware of local interests and attitudes, and do consider them in their plans. Simply put, local governments that want to get involved and want to play significant roles can and do. Those that do not advocate a position or have no input to offer do not. Although the present system is not as direct in effect in regard to local control as Saperstein's, it does work. It does so without the red tape that would result from developing miniature regulatory authorities in every county in which mining occurs. Although local input is important, there are many more sections of the Surface Mining Control and Reclamation Act (SMCRA) than Sections 508(a)(8) and 522(a)(3)(A) that also are important. It appears Saperstein's paper may overindulge these sections. An additional specific comment is made in regard to the statement that while local areas benefit from mining (wages, salaries, and purchases), they also endure environmental deterioration caused by mining affects. It is believed that the whole purpose for which SMCRA and its resulting regulations were enacted and developed was so mining would not be permitted if significant environmental deterioration could occur. Therefore, it could be argued that this point under current law is moot. Reply by L.W. Saperstein P.J. Ehret writes in a reasoned and rational way and makes some good points. The arguments in favor of central control of the designation process reflect all of the benefits associated with central environmental control: consistency of enforcement, efficiency of operation, ease of communication among enforcing agency, etc. Nonetheless, the decision to mine or not to mine is a landuse decision which, in substance, is similar to the decision to build a shopping mall, a new highway, or a housing subdivision. Although, state and federal governments' interests in the protection of public welfare are real and are expressed properly in mining laws and mining enforcement agencies (OSM, Illinois Department of Mines and Minerals, etc). I continue to maintain that the permitting and designation processes should originate with local government, which is in keeping with the American tradition of delegation of the land-use decision to local or regional government.

Jan 4, 1984

By H. Staton, N. Michaelson

"INTRODUCTION Lundin Mining’s Eagle Operation, located in Marquette County, upper Michigan consists of a mine and concentrator that process a Ni-Cu-(PGE) ore. The mine itself is an underground operation and the ore is trucked from the Eagle mine site 66 miles to the Humboldt mill where both nickel and copper concentrates are produced. Operations began in 2014 and continued with an average production of approximately 23,000 tonnes of Ni and 20,000 tonnes of Cu per year for the first three years of operation. The Humboldt Mill, currently operated by Lundin Mining, processes the nickel/copper ore from Eagle Mine and performs the concentration through several stages of flotation. Originally built in 1954, the Humboldt Mill began operations as an Iron Ore processing facility, and was converted to a gold processing plant during the 1980s. Various groups owned the site after closure of the gold operation. Eagle purchased the Mill in 2008 and invested more than $280 million to clean up historic mine waste and refurbish the plant (see flowsheet in APPENDIX). This paper will overview the ramp-up of the operation, and discuss some specific areas that went well and some that could have gone better during the design phase. HIGH LEVEL DESIGN CRITERIA Coarse ore arrives from the mine and is stored in a building with a capacity of 10,000 tonnes. Ore is crushed in three stages to a final product size of 100% Passing 12mm. Crushed ore is conveyed to the mass flow fine ore bins, which have a live capacity of 3000 tonnes. Crushed ore is fed to two parallel 900 HP ball mills, charged with 3” high chrome grinding media, and ground, in closed circuit with hydrocyclones, to a p80 of 110 microns in the flotation feed. Soda ash is added to the mills based on process water hardness. Cyclone overflow passes to the bulk conditioner where Sodium Isopropyl Xanthate (SIPX) and Methyl Isobutyl Carbinol (MIBC) are added. The slurry is pumped to the rougher bank for bulk flotation. Rougher concentrate is fed to a 500HP vertically stirred regrind mill and is ground to a p80 of 50 microns, using 5/8” high chrome balls. Rougher tailings report to the tailings thickener. The regrind cyclone overflow is sent to the single stage cleaner bank followed by two scavenger banks. The cleaner concentrate is pumped to the copper-nickel separation circuit. Cleaner tailings report to the tailings thickener. In the copper-nickel separation circuit, the pH is raised to 11.5 and a copper concentrate is recovered from the bulk cleaner concentrate in two stages, namely the copper roughers and the copper cleaner columns. The concentrate from the copper flotation columns is the final copper concentrate. The tailings from the columns return to the head of the copper-nickel separation. The nickel concentrate is the copper rougher tailings stream."

Jan 1, 2018

By J. S. Orphanos

The requirements for controlling air and stream pollution are a most timely subject for all concerned people. The coal industry has taken great measures to reduce both types of pollution. Through the use of more efficient scrubbing equipment on their thermal dryers, pollution has been considerably reduced. In many cases, the complete elimination of thermal drying by using centrifugal dryers to dewater fine coal products and meet customer specifications has completely eliminated air pollution from this source. To help eliminate stream pollution and the hazards created by tailing ponds, the coal industry is using centrifugal dewatering equipment. Use of centrifugals to dewater fine refuse for disposal would eliminate refuse ponds or extend their life. In doing this effectively and economically, preparation plants have the option of recycling the clarified water to close the water circuit or of discharging the water into receiving streams with the assurance that it contains an acceptable amount of refuse solids.

Jan 1, 1974

By D. W. Struhsacker

Mineral exploration has evolved into a sophisticated science which uses powerful scientific tools to make mineral discoveries. In addition to their usefulness in performing mineral exploration, these scientific tools can assist the exploration geologist in assessing environmental conditions at exploration sites. During exploration, environmental data acquisition should focus on data collection efforts which can be easily integrated into exploration activities, and should provide information needed for pre-feasibility and preliminary engineering design studies. Environmental studies performed during exploration should also include an environmental liabilities audit and a fatal flaw analysis to assess whether there are any unresolvable environmental or regulatory issues affecting the project. Performing extensive environmental baseline studies during exploration and project evaluation is neither necessary nor recommended. This paper describes opportunities to integrate environmental data collection with mineral exploration activities. This paper also examines how political and communication issues can affect the outcome of permitting efforts, and recommends a strategy to improve the industry's ability to respond to political challenges and to communicate with the public. This strategy integrates technical and political issues, and implements programs to convince the public of the mining industry's technological achievements and its commitment to resource stewardship and environmental protection.

Jan 1, 1994

By Shosei Serata

In the past, salt cavities for storage of liquid and gaseous fuels have been developed and operated using practical experience as a guide rather than rock mechanics principles and practices. Although many salt cavities are still operating satisfactorily. some of them are beginning to show various problems associated with long-term deterioration of the cavities. This paper describes a major breakthrough in the rock mechanics design of solution cavities which is the development and application of the REM computer simulation system. From the computer simulation analysis, the long-term deterioration process of cavities can be related to the basic parameters of rock mechanics design and the storage operations. The computer simulation system is also used for optimizing cavity design and operational specifications. This optimization technique is explained by its application to the three basic storage systems: 1) open dry storage system for liquids and solids 2) open wet storage system for liquids 3) pressurized storage system for gases, liquids and solids The effectiveness of the optimization technique is illustrated with some field examples by showing the direct interaction between the computer simulation system and field data of a test well including tectonic stress conditions, material property coefficients and geological anomalies.

Jan 1, 1974

By C. J. Pritchard, R. D. Jacksha, K. V. Raj, C. B. Sunderman

In underground metal/nonmetal mines, repeated localized short-term exposure to high levels of airborne contaminants can become a serious health issue. Currently, there are no common mechanisms to control or mitigate these short-term high exposures to contaminants. To improve miners’ health and safety, the U.S. National Institute for Occupational Safety and Health’s Spokane Mining Research Division (SMRD) is developing a smart monitoring and control (SMAC) system for the real-time monitoring of mine air quality, with integrated countermeasures to reduce high concentrations of airborne contaminants in localized sections of mines. To develop and test a SMAC system capable of being implemented in an underground mine, SMRD researchers built a test apparatus incorporating a fan, louver, ducting and sensors combined with atmospheric monitoring and control software. This system will institute effective countermeasures to reduce contaminant levels, improving miner safety and health.

Jan 1, 2018

By William W. Wellborn

Abrasives are substances both natural and synthetic that are used to grind, polish, abrade, scour, clean, or otherwise remove solid material usually by rubbing action (as in a grinding wheel), but also by impact (pressure blasting). Facts about the discovery, early use, adaptation, and development of abrasives prior to the 20th century are few. From the sparse, earliest information that is available, it would appear that the science of abrasives began when, to fashion his tools, man began to select certain kinds of rocks in preference to others because of their peculiar properties. There is evidence that stones were sawed by some sort of grinding machine as early as 4000 BC in Egypt. The real expansion of abrasives use coincided with the beginning of metallurgy in the Middle East around 2000 BC. The earliest confirmed use of abrasives for grinding metal comes from a steel dagger found along with a sharpening stone which was dated at about 1500 BC. Natural and manufactured abrasive substances play an important role in fashioning and finishing numerous products with a wide variety of end-use applications. The mining and preparation of crude, natural abrasives for their markets and the manufacture of synthetic and other abrasive materials contribute significantly to the US economy (Table 1). In addition, just as sawing to specific dimensions enhanced the value of the Egyptian stone, the use of abrasives in fabrication of modem products, and the addition of abrasives to others, add value. GENERAL CONSIDERATIONS The most important physical properties of materials that qualify as abrasives are hardness, toughness (or rigidity), grain shape and size, character of fracture (or cleavage), and purity (or uniformity). To fabricate bonded abrasive products such as grinding wheels, additional considerations include stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one singular property is paramount for any use. For some applications extreme hardness and toughness are needed, as in diamonds for drill bits. For other uses, factors of greatest importance are hardness and ability to break down slowly and, in the process, develop fresh cutting edges when grains become worn. In garnet sandpaper, for example, highly cleavable, friable, or extremely tough grains are not desirable. For other uses, extreme hardness may be objectionable. Abrasives for dentifrices and for glass-cleaning soaps are cases in point. For the most efficient uses in more critical applications, different types of abrasives are rarely completely interchangeable. While crushed quartz and garnet are both used in sandpaper, the two abrasives are not at all interchangeable in their applications. In the final analysis, the choice of a high-grade abrasive depends upon the quality and quantity of work performed by the abrasive per unit of cost. Initial cost of an artificial abrasive may be much greater than that of a natural abrasive, but the artificial mineral may do so much better work and do it so much faster that the ultimate cost is less. It is for this reason that artificial abrasives have largely replaced natural abrasives.

Jan 1, 1994

By Michael J. Cruickshank

MICHAEL J. CRUICKSHANK SENIOR AUTHOR Marine mining is a very broad field. It encompasses every facet of terrestrial mining but with the unique addition of a superimposed liquid overburden, which is itself mineralized. It is the unique aspects of marine mining that are discussed in this section. In keeping with the times, a systems approach is taken in the presentation of the material. The environment is first described, and this is followed in logical sequence by the common requirements for working there, then the mineral exploration phase, the exploitation and, finally, the operational restraints imposed by man and nature. Free use is made of tables and figures from original and published works and extensive listings of reference material round out each section. The title "Marine Mining" was chosen in preference to ocean or underwater mining because it is broad enough to include oceans, beaches and inland seas. The selection of terms sometimes may seem odd but they have not been chosen arbitrarily. All things are reduced, where possible, to basics and defined. Applying systems terminology, the word "platforms" is used in the functional sense and includes not only airborne, waterborne and fixed platforms, but man himself in his capacity as a working diver. If there is confusion it is often because of familiarity with a word in a context personal to the reader. For example, what does extraction mean to you-or mining or exploitation? Cost data have been interspersed throughout the section whenever they could be obtained. The use of these data should be tempered with understanding because no two situations are alike and improvements in marine technology are constantly being made. The names of individual authors are listed with each subsection. Where no name is given, the responsibility has been that of the senior author. Acknowledgment is sincerely made to the U.S. Bureau of Mines, and latterly the National Oceanic and Atmospheric Administration, for encouraging and supporting the preparation of the work ; to the secretarial staff at the Marine Minerals Technology Center and to Donald Eisman for editing. To the many other contributors who may not be listed by name, grateful acknowledgment is also due. It is hoped that the chapter will be useful to the practicing mining engineer who suddenly is assigned to marine work or to the experienced marine engineer who is equally suddenly assigned to mining work. It is not possible to put "everything-you -need-to¬-know" into one section, but. the very full bibliographies at the end of the text should adequately fill in for those who wish to know more. 20.1-THE MARINE ENVIRONMENT Marine mining is set apart as a separate discipline by the marine environment. The following subsections describe the environment from the point of view of the physicist, the chemist and the geologist. The interrelationship of these disciplines with the economic mineral potential of the oceans and seas is apparent from the description of the marine mineral resources. The marine environment is an extremely complex natural phenomenon with which the marine mining engineer must learn to live. It can be the source of his wealth or his frustrations and sometimes both. It can never be ignored.

Jan 1, 1973

By Robert V. Price

It is a pleasure to be here today to discuss coal's prospects with the Society of Mining Engineers of AIMS--- a group destined to play a crucial role in shaping our national energy future. Much has been said lately about attaining domestic energy self-sufficiency, but to date, little has been done. Oil tankers from Venezuela and Kuwait continue to glide across the seas to meet our incremental energy needs. Meanwhile, our principal domestic energy resources -- oil and natural gas reserves in the Outer Continental Shelf and the oil shale deposits and the coal lands of the West -remain untapped. Help, however, appears to be on the way. In a forceful address last fall, President Ford called for the elimination of oil as a fuel for base-loaded power plants and its replacement with coal by 1980. He also urged the accelerated leasing of federal lands on the Outer Continental Shelf, the resumption of coal leasing on federal lands, and the development of a new energy conservation policy. There are, of course, many details left to be worked out. Language must be developed to put statutory flesh on the conceptual bones spelled out by the President. Congress must act. Regulations must be approved and tested, if need be, in court.

Jan 1, 1975