Search Documents

By M. J. Hart

Today, aggregate producers in the Denver Metropolitan area, herein defined as Denver and surrounding communities in Adams, Arapahoe, Boulder, Douglas and Jefferson Counties, are scrambling to secure their future reserves. The Denver market is somewhat unique among the larger metropolitan markets in that the source of needed aggregate for the future is very much undecided. 2. Present Aggregate Resources Presently, the annual consumption of aggregate resources in the Denver Metropolitan area amounts to approximately 16 million tons of sand, gravel and crushed stone of which the later accounts for about 20%. Based on population growth projections for the front range, by the year 2000 the annual rate of consumption for aggregate in the Denver Metro area could be in the 25+ million ton range.

Jan 1, 1987

By D. A. Poukhovski

Two integral components of the 30 CFR 48 training requirements mandated for new miners, newly employed experienced miners, and the annual refresher training of all miners are hazard recognition and prevention of accidents. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine, and a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition places a particular challenge before safety-training specialists because they are often limited in their ability to adequately gauge the trainees' levels awareness prior to training. Further, they must also assure that the training is relevant, and it is presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard-recognition topics because it can be used in pre-training and post-training modes for assessment of training effectiveness, in addition to use as a presentation tool. Therefore, this paper will present a recent approach developed at Penn State to apply this technology for assessment and instruction of accident prevention through hazard recognition, with an application prepared for surface coal mines.

Jan 1, 1997

By Jamal Rostami

Continuous miners (CM) are the most popular underground mining machinery in soft rock mining, playing a dominant role in the production of minerals ranging from coal to evaporites while finding increasing use in salt and potash mines. Along with the ongoing technological advancements in the mining industry and the underground equipment, new generation of CMs offer several new features that are designed to enhance their operational capabilities and production rate. In addition to new bits and bit holders, one of the areas of improvement is the cutterhead design through computer modeling and simulation based on the full scale cutting tests. This paper discusses the state-of the-art CM technology and development of the computer models for design analysis and performance estimation of CMs. The general approach used in the modeling, along with the results of field trials for several projects will be presented.

Jan 1, 1998

By John E. Riddell

This review is based on a questionnaire sent out to 24 Canadian exploration companies, known to be active in the mineral exploration field, concerning their practice in the use of applied geochemical techniques in Precambrian terrains. Of the companies questioned, 16 returned completed questionnaires and of these, ten companies stated that they had some experience in this type of work. Of the companies who did not answer or return the questionnaire in time I know that at least three have been quite heavily engaged in applied geochemical work in the glaciated Precambrian areas. I also know that these three companies have been reasonably successful in their ventures, so I feel the following figures and opinions are, if anything, on the pessimistic side. Before continuing with the paper I would like to express my personal thanks to the Chief Geologists, Geologists and Exploration Managers of the various companies who cooperated in making this review possible by answering the questionnaires and making available summaries of their work in the glaciated terrains. Of the companies who stated that they had no experience in geochemical prospecting in glaciated Precambrian areas it is interesting to note that only two have reported that they do not use applied geochemistry at all. Two companies have reported that they make use of applied geochemistry in New Brunswick in areas of-light glaciation. Their opinion is that it is a useful aid to other techniques in evaluating mineralized areas.

Jan 1, 1960

By M. R. Grundy

The Robinson project is based on the porphyry copper and gold deposits in the Robinson Mining District, near Ely in Eastern Nevada. The district was mined from the late nineteenth century to 1978 by Kennecott Copper Corporation and its predecessors. Operations ceased when falling copper prices in the late 1970's made their outdated mill and smelter complex at McGill uneconomical. In October 1991, Magma Copper Company (Magma) acquired the many claims that cover the known porphyry copper deposits in the district These occupy a disturbed area about nine miles long and three miles wide between the towns of Ely and Ruth. Magma proposes to build a copper / gold mine and concentrator and expand the existing gold leaching facilities. Several pits, previously mined by Kennecott Copper Corporation, will be enlarged; the use of larger, more modem equipment will result in higher productivity and lower operating costs in general. ICF Kaiser Engineers, of Oakland, California, were awarded the con-tract for detailed design of the process facilities, which was essentially complete by the end of 1993. The project at present is awaiting completion of the environmental permitting process; state air and water permits are in hand, and the Bureau of Land Management's (BLM) current schedule indicates that the final obstacles to construction will be cleared by early fall of this year.

Jan 1, 1994

By A. Konya

"INTRODUCTION Underground Mining and Construction projects face several challenges unique to the underground environment compared to the surface environment. The goals of an effective blasting program are the development of a blast pattern that minimizes cost, maximizes face advance, and provides the desired fragmentation and face profile. In addition to these , mines must consider the very real operational problems that occur such as drill deviation, ground vibration, and deadpressing or sympathetic detonation of explosives. These operation problems lead to increased costs and decreased production in the mine, hurting the bottom line. Combined with these problems, underground blasts can be difficult to monitor and evaluate due to tight spaces, dust during the blast obscuring video, and the need to evacuate the immediate area with no clear line of sight to observe performance. This creates an environment which most mines know that blasting can be improved in their underground operations, yet most are hesitant to change due to fears of the shot freezing, misfires occurring, and questions about how to achieve a proper design. The explosive companies and shot service providers also offer limited assistance or knowledge in the underground blasting realm, unlike with surface blasting, leaving many underground operations in the dark. It is for these reasons that most underground operations are operating decades behind the current technologies and incurring significant costs, both real and hidden, from there blasting operations. This paper discusses philosophical changes to designs that need to be made for effective design and modifications of underground blast patterns to prevent deadpressing and precompression of modern explosive products (Konya, Konya, & Worsey, Modern Blasting Method Selection, 2017). While numerous different methods of underground heading development exist, there are two types that are used in a majority of mines around the world, these are the burn cut and the V-cut. The burn cut is a parallel cut that has holes that go straight into the face and are primarily used in smaller opening (due to ability to pull deep rounds with smaller room widths) and metal mines (helps in ore dilution and greater fragmentation). The V-Cut is a cut that uses angled drilling towards the center of the face (in the traditional method) and is primarily used in underground aggregate operations due to its cheap cost but larger fragmentation sizes and greater throw of the muckpile. This paper will discuss these two forms of cuts specifically with the understanding that modifications to these can be applied to other parallel and angled underground heading techniques. BURN CUT The burn cut is one of the older forms of underground blasting, where a part of the blast (burn) of a shot is heavily loaded with additional empty (relief) holes with the goal of smashing (aka burn) and pushing/blowing all the material in the burn out to provide relief for subsequent blastholes. The relief holes in the burn cut provide a parallel relief for the holes that are firing to break too creating a second plane of relief, however these are extremely small and can cause many problems if a design is improper."

Jan 1, 2018

By B. N. Everett

The growing role of Colombia as a major supplier of internationally traded steam coal has been widely discussed in the industry. Although Colombian coal has been produced and exported in small quantities for a number of years, Colombia's position as a major coal exporter began in earnest in 1985 with the first commercial exports from the Cerrejon North Block Project. By way of background: ? The mine is located on the Guajira peninsula in Northeast Colombia, about 90 miles from the coast, as shown in Figure 1. ? In addition to the mine itself, the project involves construction of a dedicated railroad and port, which form a modern, efficient and integrated system. ? The Project is embodied in a 50/50 Association Contract between International Colombia Resources (Intercor), a wholly owned subsidiary of Exxon, and Carbocol, the Colombian state coal company. Intercor and Carbocol share investment and operating expenses equally and Intercor has the additional responsibility of managing operations on behalf of both partners. Each partner is entitled to 50% of the coal produced, and each markets its share separately. ? The project is a multi-seam, truck and shovel operation, based on large reserves (2-3 billion tonnes') of high quality bituminous coal. ? Exports began in the first quarter of 1985 at modest levels through what we call Early Coal Facilities, designed and constructed apart from the permanent coal handling system. ? Production will increase rapidly in each of the next few years, reaching the design capacity of 15 Mt per year in 1939. Based on available resources, however, the resource will support expansion, and continued growth n production into the 1990s appears feasible.

Jan 1, 1986

By B. Seymour

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop safe practices for the use of shotcrete as ground support in underground mines, particularly mines operating in weak host rock. As part of this research, tests were conducted with a commercial poly-fiber reinforced shotcrete mix to develop a practical means of measuring shotcrete adhesion strength. Full-scale tests were conducted in a test frame equipped with concrete panels having three distinct surface roughness profiles. Adhesion test fixtures either embedded or epoxied in the shotcrete were overcored into the underlying concrete, and direct tensile tests were conducted to determine the bond strength of the shotcrete cores to the substrate after a selected shotcrete curing interval (1, 3, 7, 14, 28, or 90 days). Measured adhesion strengths typically ranged from 0.5 to 2.0 MPa depending on the curing age of the shotcrete samples. This paper presents the results of these tests, describes the portable test system components, and addresses some of the design issues encountered in the development of a rugged and reliable method for determining shotcrete adhesion strength in underground mines.

Jan 1, 2010

By R. V. Ramani, R. Bhaskar

An airborne dust cloud is an ensemble of particles of varied size, density, shape and states of aggregation. An understanding and quantifying of the dispersion and deposition of the dust generated in mines is essential to the development of measures for reducing worker exposure to dust. In coal mining, the major portion of the dust is generated during the cutting of coal using a shearer or a continuous miner. The major phenomenon affecting ambient concentration is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian and eddy diffusion and inertial impaction. The three major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. The mechanisms determining particle deposition are size dependent. From a review of the literature, there appears to be a knowledge gap in the understanding of the deposition phenomena in mine airways. In order to obtain a better understanding of the deposition of dust for various particle sizes, and to develop a set of data for evaluating predictive mathematical models for dust-flow in mines, a series of dust flow experiments was performed under controlled conditions in mine airways. It appears that the deposition data generally follow the theoretical behavior of dust based on the combined effect of diffusional and gravitational deposition. In this paper, the findings of the study on the deposition of dust in mine airways and its dependence on size, velocity and concentration are discussed. A set of deposition equations that could be used to determine the approximate deposition at various points in a mine airway are presented.

Jan 1, 1992

By J. R. Koehler

Mining practices at the Sunnyside Mines, Sunnyside Coal Company, Sunnyside, UT, have been documented by U.S. Bureau of Mines researchers to preserve the extensive history of yield pillar-based longwall gateroad system evolution on the property. An overview of the historical mining conditions, practices, and innovations that resulted in the evolution of the two-entry yield pillar gateroad system currently employed at Sunnyside was developed from interviews of 30 long-time Sunnyside employees. Employing yielding chain pillars at Sunnyside virtually eliminates tailgate pillar bumps and contributes to reducing face bumps. Limiting the overall width of the gateroad system benefits bump control and especially, roof and floor stability.

Jan 1, 1994

By M. J. Gula

In the solvent extraction -electrowinning recovery of copper from oxide or sulfide ores there is a continuous transfer of iron and other impurities from the primary leach solution to the copper electrowinning electrolyte via chemical transfer or mechanical entrainment. Iron is the principal impurity that has to be controlled in the electrolyte by a "bleeding" of the electrowinning solution. This bleeding transfers copper and sulfuric acid back to the primary leach circuit along with the iron. Copper is recovered via the solvent extraction process and generally the sulfuric acid is used as a reagent in leaching. Unfortunately, cobalt, which is added to the electrowinning solution to modify the anodic process, is irreversibly lost through the bleeding operation. This cobalt loss represents a significant operating cost to SX-EW copper producers. DiphonixTM ion exchange resin contains diphosphonic acid and sulfonic acid functional groups on a polystyrene-divinyl benzene matrix. This resin has been found to strongly and selectively extract ferric ion from copper sulfate -sulfuric acid solutions containing cobalt. Thus, an ion exchange process using DiphonixTM resin for the control of iron has been developed to replace the conventional bleed stream process. The new process minimizes the loss of cobalt from the electrowinning circuit and strips the iron into a sulfate based solution suitable for leach solution makeup. In addition, this process can effect a lowering of the total iron concentration in the electrolyte circuit with an associated increase in current efficiency. In this paper, data on the loading and elution of iron are presented. Laboratory and pilot scale data will be discussed along with information on process design and comparative economics.

Jan 1, 1996

By Larry D. Patts

Section 317(e) of the Federal Coal Mine Health & Safety Act of 1969 directed the Secretary of the Interior to prepare standards under which all working places in a mine shall be illuminated by permissible' lighting while persons are working in such places. Section 317(e) further provides that such Working places shall be illuminated within 18 months after such standards are promulgated. In accordance with this section of the Act, there was published in the Federal Register for December 31,1970 a notice of proposed ru1emaking which prescribed the illumination to be provided in the working p1 aces of underground coal mines. In 1ight of written comments, suggestions, and objections to this proposed ru1emaking, the proposed standards were with-drawn and reproposed in the Federal Register for Wednesday, October 27, 1971. In light of further comments, suggestions, and objections, a public hearing was held on April 4, 1974 and standards were again reproposed and published in the Federal Register for April 1, 1976. Promulgation of the final lighting standards took place on October 1, 1976 which means that the underground coal mining industry must comply with face illumination requirements by April 1, 1978. As mentioned previously, the first proposed ru1emaking for illumination of underground coal mines was published in the Federal Register on October 27, 1971. In early 1972, Consolidation Coal Company (Consol) and the United States Bureau of Mines agreed to a cooperative study of underground face illumination; Conso1 felt that expertise in this field would become increasingly important. Conso1's initial efforts in illumination were aimed at investigati.ng practical lighting systems for underground face equipment. We were concerned with installing unobtrusive lights which provided sufficient face illumination for safety, but at the same time were readily maintainable, electrically reliable, and physically sheltered from damage.

Jan 1, 1977

By Robert D. Deister

The Buick Concentrator represents state-of- the-art technology in automated digital process control operation utilizing a centralized computer. The process control strategies implemented at Buick are no longer new to the industry but the successful application of these developments is still rather unique in North America. Productivity improvements, determined to be a direct result of the process control developments, are the primary topics of this paper. Emphasis is placed on metallurgical benefits including both lead and zinc recoveries, lead concentrate grade and reductions realized in reagent consumptions, operating costs and personnel. The productivity improvement discussion is preceded by a concentrator description and a brief history of the process control development at Buick. Current control strategies and future applications are presented afterward.

Jan 1, 1985

By Douglas W. Barr

Water is a necessary part of our environment. It is a biological necessity, but more than that, it is a necessary part of our life style. Those of us who live in the north woods expect water to be part of the scene. There are few natives of this region who would be content to eliminate the streams, the lakes, the marshes, or our forests. Throughout the world, water has been so much a part of man's environment and man's adaptation to life has been so closely tied to water that our way of life and ways of accomplishing our work include water as an essential tool. The production of taconite is an example of our dependence on water. Other methods could have been developed to process taconite ore but the process methods chosen utilize water. Water is used for grinding and separation and for trans- porting the ore from one part of the process to another and for dust control. A typical large plant producing 10 million tons of taconite pellets per year will have on the order of 130,000 gallons per minute (8.202 m 3/51 of water in circulation in the plant. About 120,000 gal. per min. (7.571 m 31s) will pass to tailing thickeners where 110,000 gal. per min. (6.940 m 31s) is separated from tailing and returned to the process. About 15,000 gal. per min. (.9464 m 31s) goes with thickened tailing to tailing basin. My point is that there are great volumes of water in motion in a taconite plant,

Jan 1, 1980

By J. A. Madonna

Independent prospectors and small to large-scale exploration company personnel have requested, and are in need of, guidance in geochemical field sample collection methods which will provide the most reliable results during chemical analysis. In cooperation with analytical laboratories, experienced geochemical exploration scientists and mining companies a systematic collection procedure has been developed. The procedure consists of collecting uncontaminated, water, sediment and rock chip samples of the appropriate quantity and/or dimensions to meet the needs of analysis.

Jan 1, 1999

By G. Barrasso, E. Nordheim

"The European aluminium industry, through its member organisation the European Aluminium Association (EAA), initiated a program on sustainable development for the aluminium industry in 2001. The first step involved the development of a set of sustainable development (SD) indicators for the industry, taking into account of the different interests involved and also the different existing conventions. The indicator set was developed during 2001 and 2002 with the assistance of recognised partners, including Wuppertal Institute from Germany and Versailles University from France. As well, both internal and external stakeholder groups were involved in order to validate the indicators. This has resulted in a set of thirty-four indicators used in the first survey exercise. In the survey the EAA, together with the national aluminium associations, attempted to cover all European plants producing alumina, primary aluminium, rolling ingots, extrusion ingots, foil and recycled aluminium -covering approximately 800 plants. The survey used two points in time, 1997 and 2002, in order to start developing a trend for the individual indicators and to measure progress over time. The industry response to the survey was very positive, with a total industry coverage based on tonnage reported of over 80% for 2002 data and 70% for 1997 data. The results also show a solid progress for most indicators and particularly for social indicators such as training performance, community involvement and employees health programmes. The EAA is committed to conducting this as a regular exercise and is engaged in a number of stakeholder workshops in order to present the survey results, to review the indicators used and to also consider adjustments of these based on feedback from stakeholders and experiences from the first data collection."

Jan 1, 2005

By Fernando H. Muge

The first application of dynamic pro¬gramming to the problem of grade control and scheduling was by Muge et al (1979) and Ribeiro (1982) who applied it to the simple, two-dimensional case of longitudinal open stoping using two sublevels. In this paper the formulation of the problem is extended to cover the general case applied to a cut-and-fill mining method. The criterion for optimization is the total deviation of the average, grades of mining blocks from the overall average panel grade (or the average grade of a set of mining panels or the mine processing working point). This means to schedule the operation by removing a certain number of mining blocks at a time, subject to the geometric (mining) constraints, and such that the total deviation of average block grades from overall average grade is minimum. The method can be applied to complex orebodies with several ore characteristics and the deviation of each one of these characteristics can be further constrained by specifying maximum values. The method can also be generalised in order to take into account any necessary geometric constraints used to define the mining method. In this paper a case study is presented concerning the mine planning of a complex sulphide orebody located in the South of Portugal. As input for the definition of the mining sequence, a geostatistical numerical model of the orebody was built based on a previous ore typology. The short term planning is used to assess specific mining sequences and the production scheduling is performed on the basis of an objective function (e.g. minimization of grade fluctuation).

Jan 1, 1989

By Wu Chao, Wang Pinglong, Meng Tingrang

This paper discusses the research results of sulphide ore properties with respects on self-heating and the assessment techniques on mine spontaneous combustion for several mines of sulphide ores in China. A group of experimental devices for testing the chemical behaviour of sulphide minerals, the geological structures, the rate of oxygen absorption, the initial self-heating temperature, and the ignition point of ore samples, etc. are also described in detail. These methods have been proved to be effective by several sulphide mines which all have the history of spontaneous combustion of sulphide ores. INTRODUCTION A fire disaster from the spontaneous combustion of sulphide ores in a mine can produce large quantities of toxic gases and heat to pollute the working environment, lead to large economic losses and loss of human life, and even compell the mine to be closed. Some mines of copper, lead, zinc, tin and iron in China are of high content of sulphur. It is of great importance to evaluate the potential of spontaneous combustion of sulphide ores before beginning to design and mine the ore deposits. At present, the mechanism of spontaneous combustion accepted commonly is that sulphide ores undergo slow oxidation on exposure to moisture air at ambient temperature, with the evolution of heat, gases and moisture. The heat generated, if not dissipated, gives rise to an increase in the temperature of the sulphide ores. As the temperature of the sulphide ores rises, the rate of oxidation increases. If this is allowed to proceed unchecked it can eventually result in the ignition of the sulphide ores. For pyrite (FeS2), it reacts with oxygen and water according to the following equations.

Jan 1, 1993

By Rory P. A. Ball, Mark Briggs, Martin Dix

"Tunnel professionals should inform project stakeholders on the reality that tunnel projects are not 100 percent devoid of the need for excavations or public inconveniences during both design and construction phases. Competing stakeholder objectives to limit these disruptions must be weighed against the need to mitigate risks and to produce a constructible, operable and maintainable end product. Perhaps the approach we should take with stakeholders, also known as Authorities Having Jurisdiction (AHJs), is sharing memorable case studies that bring to life the potential risks so often buried within lengthy risk registers. This paper provides a sobering case study describing what can occur if the presence and/or location of utilities and other obstructions are not fully understood due to restrictions placed on exploration or mining operations. In this instance, the Microtunnel Tunnel Boring Machine (MTBM) encountered a buried concrete structure, followed by rows of abandoned wood piles, before finally colliding with an active high-pressure gas main under a bustling coastal highway. Multiple stakeholders imposed tight logistical and other work restrictions, compounding the difficulties experienced during the drive. However, the difficulties were effectively managed through the project team’s proactive collaboration and communication with everyone involved. INTRODUCTION Some of the most important decisions that influence the ultimate success or failure of a project may not be made by design engineers. Instead, these decisions are often made by project stakeholders and third-party agencies. Tasked with protecting the best interests of their users, these agencies are cautious of potential impacts associated with project construction and subsequent use. Unfortunately, actions required (or restricted) by stakeholders often result in unwanted ripple effects that negatively affect the very users they are trying to protect. For example, a mandate limiting a shaft site to an unreasonable size may be intended to reduce local business impacts, but may actually increase impacts as more supply and truck hauling is required."

Jan 1, 2016

By Devraj Sharma

This paper presents technical issues in the design and management of a retorted oil shale disposal site. Major physical and geochemical mechanisms which affect the disposal are: heat transport, moisture migration, chemical species transport, auto-ignition, and mechanical behavior alterations of the retorted oil shale pile. The interaction of these mechanisms and their relative magnitude will affect the environmental behavior of the pile. The paper discusses the coupling between the mechanisms, presents a framework to quantify the processes by laboratory and field measurements, and in addition discusses the use of mathematical models to provide quantitative predictions.

Jan 1, 1981