Search Documents

By Anders Sellgren, K. Hansson, A. Jedborn

In the mining industry, conversion of fine particles into a slurry is often part of the normal processing of the ore. Therefore. from a system's point of view, slurry transportation would be considered as a natural alternative, all the way from the working face to the final processing. In underground mines, there is sometimes a considerable inflow of ground water that has to be pumped out. When the mine dewatering installations are integrated with a hydraulic hoisting system, the cost of power needed to pump out the ground water can be excluded from the cost of hoisting, compared with other modes of transporting the solids to the surface. The chief advantage of hydraulic hoisting is that the hoisting capacity can be increased at comparatively low total cost without necessitating the sinking of new shafts. Alternative examples include deepening of the existing mechanical hoisting system, truck, or conveyor belts transport in ramps to the present level. These often become very expensive. The economic effectiveness of hydraulic hoisting and hydraulic design considerations have been discussed by Kostuik (1965) and Sellgren (1985, 1986) for both small shallow mines and large deep underground mines. Objective and scope The objective of this study was to demonstrate the feasibiliy of hydraulic hoisting in hypothetical examples of mine deepening. Underground grinding to a maximum particle size of about 700 um (about 25 mesh) is considered. The pumping of ground ore products with positive displacement plunger or membrane type of pumps at working pressures of up to 15 MPa (2200 psi) is a thoroughly tested technique (Venton, 1986). Hydraulic hoisting system A hydraulic hoisting system is described schematically in Fig. 1. The ore is mined, handled, and crushed conventionally. It is then ground wet underground. The slurry is then temporarily stored in an agitated tank and pumped to an agitated receiving tank on the surface. The ore is then further processed in the concentrator. The capacity of a pipeline is very high. For example, an annual production of 500 Kt (550,000 st) of ore can be handled in a 100-mm-diam (4-in.-diam) pipeline. Systems layout - economic effectiveness Schematic mine layouts are presented that represent situations where hydraulic hoisting often is the most economical alternative. A situation where the ore is trucked to the level of the existing hoisting system is shown in Fig. 2 (following page). With hydraulic hoisting, only a shaft for ventilation, pipe- line, and personnel are needed. In a first phase (Fig. 2). a hydraulic hoisting installation with crushing and grinding units, storage facilities, and pumps has been located at a level of about 400 to 600 m (1310 to 1970 ft) below the surface. With further development of the mine, the hydraulic hoisting

Jan 1, 1990

By Randall E. Hughes, John F. Burst

This chapter describes the nature and occurrence of the principal clay minerals that are used as ceramic raw materials, explains how these raw materials are used to produce finished goods, and summarizes positive and negative trends that will affect future demand for raw materials and products in the ceramic industry. The term ceramics was derived from the ancient Greek keramikos (a clay jar). A ceramic product is a material that has been fired to at least 468.3°C (Mitchell, 1983). In addition to being one of our earliest manufacturing and construction materials, ceramic products are among the earliest records of civilization. The enduring significance of ceramics is shown by the fact that, even today, the manufacture of whitewares, brick and related red-fired wares, refractories, and engineered ceramics continues to be a major sector of the US economy. A wide range of materials can be made into ceramic products, although relatively few earth materials make up most of the ceramics in today's markets (Table 1). Most ceramic products are made from clay or a related material. The long history of clay use in the ceramics industry stems from its variable and sometimes unique physical and chemical properties, as well as its ubiquitous occurrence and relatively low cost. Clay is important to ceramics because of its plasticity, moldability and filterability, chemical content, color. refractoriness, solubility. corrosion resistance, electrical properties, and other properties that result from the essentially two dimensional morphology of the individual clay mineral platelets. Because of their basic relationships to the chemical and physical properties of clays, the chemical and mineralogical content have been the subject of continuous studies over the past few decades. Advances in knowledge about the chemical, mineralogical, and physical properties of clays are responsible for most of the advances in processing. The need to remove off-colored contaminants, minerals with low melting points, and soluble salts has resulted in beneficiation by wet processing methods such as water washing. Water washing is restricted to kaolins, although low cost methods of water washing have been extended more recently to ball clays in Europe. High intensity magnetic filtration and flotation technologies have noticeably improved the quality of kaolins and broadly expanded their use in the ceramics industry. In addition to products for construction (e.g., brick, tile, sewer pipe, field drain pipe, cement, fiberglass, roof granules, and paint) and manufacturing (e.g., refractories, kiln furniture, sanitary ware, pottery, and dinnerware), clays are used in calcined form as ceramic fillers, carriers, extenders, and grogs. Ceramics suppliers are under economic pressure in several of these product areas. Manufacture of refractories in America has declined as steel production has decreased. Similarly, dinnerware and tile production have declined because of foreign competition. Fortunately, new uses for clays,

Jan 1, 1994

By Paul Basinski

The Northern Reese River Valley is in west-central Lander County approximately 31 miles north of Austin, Nevada in the north-central Basin and Range Province (Figure 1). Authigenic zeolites, which were previously undescribed in the literature, are voluminous in this small sedimentary basin. Uranium mineralization is also abundant in this study area. Until now, what we believe to be cause and effect have not been put together. X-ray diffraction, differential thermal analysis, and scanning electron microscopy reveal clinoptilolite, erionite, analcime, and minor chabazite to be present (Figures 2, 3). Assays show uranium to be present in thicknesses up to 0.7 meters at amounts up to 0.10% eU308. The sediments in the Northern Reese River Valley belong to the Mio-Pliocene Humboldt Formation equivalents. This formation consists largely of tuffacious lacustrine and fluviatile sedimentary rocks. Mudstone is the dominant lithology and intercalated thin zeolite strata (usually less than 0.6 meter thick) are present. Zeolites in the Northern Reese River Valley were diagenetically derived from rhyolitic glass deposited in a shallow, saline-alkaline lake under arid to semi-arid conditions. Clinoptilolite from the study area was K-Ar dated at approximately 4.7 + 0.5 million years which corresponds to Middle Pliocene age (Krueger and Basinski, in press). This age is further substantiated by Middle Pliocene mammalian fauna collected in the vicinity by Deffeyes (1).

Jan 1, 1979

By Wolfgang Güter, Paolo Romualdi

Current extensions of the European railway network require long TBM drives in the diameter range of 10 m under critical and varying rock conditions. In view of that and in particular for a 7 km long high-speed railway tunnel in Spain to be started in mid-2003 a new design for a hard rock Double Shield TBM has been developed by SELI (Italy) and Jäger (Austria) in collaboration with Mitsubishi (Japan)and Robbins (USA). Due to the new design and operational features that new type of TBM has been named Universal Double Shield TBM with a further extended area of application. Special attention has been given to outstanding torque and thrust capacities combined with the shortest possible length of an innovative shield arrangement, different advance modes in various ground conditions and further developed exploration and treatment facilities.

Jan 1, 2003

By Jacob Carr, Chenming Zhou, Nicholas Damiano, James Noll, Jingcheng Li

Machine-related injuries are one of the major safety concerns in underground coal mines. Severe injuries and fatalities occur when a miner is struck, crushed, or pinned by mining equipment such as a continuous mining machine (CMM), shuttle car, or a scoop. Proximity detection systems (PDSs) have been applied in mining to reduce these types of injuries and fatalities. All of the PDSs that are currently approved by the Mine Safety and Health Administration (MSHA) for use in underground coal mines are magnetic-field based and could be affected by metallic objects such as trailing cables. Researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated the influence of trailing cables on the performance of PDSs. In particular, the magnetic field coupled from proximity system generators to a de-energized trailing cable was characterized. The results show that significant energy can be coupled from the proximity system generators to a trailing cable when there is a closed loop in the cable. The effect on PDS performance from the magnetic field radiated around an energized trailing cable was also quantified for different current amplitudes in the cable. It is shown that the magnetic field caused by the electric current in the trailing cable mainly consists of a 60-Hz signal and its harmonics which causes little interference to the PDS. The results presented in this paper can help PDS manufacturers to design better systems that are more immune to these effects.

By N. R. Sainath

This paper discusses the results of a laboratory investigation carried out to study the microscale flow characteristics of copper ores and the variation in flow behavior resulting from flow of leach solution. Fractures in 1.5 and 4 inch diameter cores were mapped by visual inspection. The cores were stressed in a triaxial stress field representative of in situ conditions. The permeability of the samples to water was then estimated. The samples were exposed to 20 g/l sulfuric acid and the experiment repeated. The Permeability of unleached samples ranges from 10-1 to 10-19 m2 and it increases as leaching progresses. The porosity variation and the rate of recovery of copper from the specimen during leaching were also studied.

Jan 1, 1991

By Donald T. Delicate

Since the discovery of uranium in the Ambrosia Lake Area in 1955, a new mining district has developed which promises to be the greatest uranium producing area in the United States. Exploration and development work is proceeding rapidly in mines operated by Kermac Nuclear Fuels Corporation, Phillips Petroleum Company, Rio De Oro Uranium Mines, Inc., Calumet & Hecla, Inc., Rare. Metals Corporation, Homestake-Sapin Partners, Homestake-New Mexico Partners, and Centennial Development Company. Individual mining operations vary in size from 200 tons to more than 1200 tons per day with production from wet and dry ore bodies ranging in depth from 300 to 1500 feet. Many problems have been encountered during the development period in the district mines. Within this paper the author will review some of these problems and mining practices being used. In order to understand better the developments to date, a brief description of the area and its geologic setting will be presented.

Jan 1, 1959

By Jozef Stachulak

Prof. H. Bystron: "An Application of the First Law of Thermodynamics to Winter Dry Air Flow in Mr. Stachulak's Mine Model". [ ]

Jan 1, 1980

By Edwin Itzig-Heine, Daniel Traylor, Bernard Tarralle, Michael McKenna

This paper discusses the challenges associated with the design and construction of a dual-cell, “figure eight” shaped shaft in saturated, soft ground for the Northeast Interceptor Sewer project in Los Angeles. The shaft will be excavated to a depth of41 m and used to launch two EPB TBMs. The specifications required concrete diaphragm walls, embedded below the shaft invert, and a grout curtain beneath the wall. To control water pressure and basal stability without a grout curtain, wall panels were embedded deeper than required into a stiff, cohesive deposit. Details of wall panel excavation using a Hydrofraise are presented.

Jan 1, 2003

By R. K. Komarek, F. E. Jr. Briber, G. M. Hanson, Fred D. DeVaney, J. H. Blake, C. L. Matson, T. E. Ban, N. E. Shields, R. D. Frans, R. B. Greenwalt

Metallurgically, the term agglomeration is used to describe processes whose goal is to form balls, briquettes, nodules, flakes, or other sized shaped particles from loose, usually fine, incoherent particles. In practice it includes such varying processes as the briquetting of coal dust and other substances, the balling and induration (heating) of such nonmetallics as cement, fluorspar, lightweight aggregates, etc. It includes such widely used processes as the sintering of nonferrous concentrates, such as those copper, lead, zinc, etc. The agglomeration of specific nonferrous metal concentrates is discussed in detail in the section of this handbook devoted to that particular metal. Agglomeration processes are of particular value to the iron and steel industry where the nature of the primary reduction process, the blast furnace, requires for best results a burden essentially free of fines. This is a change that has taken place since about 1960. Prior to that time many fine unsized ores were fed to the furnace. The development of the pelletizing process gave to the industry a chemically controlled closely sized product that increased the produc¬tion rate and reduced the costs so much that unsized fines are seldom used in modem furnaces. Steel plants produce many fine sized waste products such as fine dust (fine ore coke and gangue) and mill scale. These products, which have a valuable iron content, are usually sin¬tered directly at the plant for reuse. Fine sized ore concentrates are usually pelletized at the mine and shipped as pellets to the steel plant. Common practice in some areas producing natural high grade ores is to screen the ore at the mine to about 3/8 in. The oversize is shipped "as is" and constitutes blast furnace feed. The / in. may be shipped to the steel plant where it may be sintered or otherwise agglomerated. At some mines the fines may be pelletizied prior to shipment. With the development of large ocean ore carriers, and with the transportation of slurried concentrates or fines, a trend has developed of constructing large pelletizing plants or other types of agglomeration plants near large consumption centers (i.e., in the Netherlands or Japan) where ores of many types are brought together, ground if necessary, blended, and agglomerated. As an indication of tonnages of agglomerated materials produced, for iron materials alone (the largest share of the total) production in 1970 in the U.S. was Million gross ton Sinter 40.7 Pellets 43.1 Briquettes, nodules, & others 0.1 Total 83.9 During the 1960s, U.S. production of sinter rose from 40.3 million gross tons in 1961 to a high of 48.7 million in 1964, then settled back to almost the 1961 figure in 1970. Pellet production rose steadily from 14.4 million gross tons in 1961 to the 59.9 figure for 1975. Worldwide, sinter production in 1966 was estimated at 340 million mt (mainly in Europe, Russia, Japan, and the U.S.) and pellet produc¬tion the same year at 64 mt (primarily Canada and the U.S.). World pellet production capacity rose to 200 million tons in 1976.

Jan 1, 1985

By R. E. Gertsch

Mechanical mining holds great promise for the mining industry. Realizing this promise depends on giving mine operators the capability to evaluate the higher production, the lower costs, and safety enhancement that comes with mechanical mining. The opportunities for low cost and high production must outset the high capital costs associated with mechanical excavation. Giving the mining industry the tools to effectively evaluate and successfully implement mechanical methods defines the challenges and directions of the mechanical mining industry.

Jan 1, 1994

By Dale D. Teeters

Today, I would like to talk about ways to maximize the efficiency of surface coal operations. I doubt I will present any startling new ideas, but my comments may, hopefully, stimulate some conversation today and later back at your own operations. Strip mining is a very old technique used by ancient societies. Only with the coming of the machine age in the early twentieth century did we attempt to increase the magnitude of our operations. The industry, as we know it today, really only got started in the early 1900s with the advent of steam shovels. In the first portion of this presentation, I will attempt to show that we have, in many cases, not changed the basics of strip mining, only the scale. In doing so, quite often we have complicated the operations to the point of being unmanageable and unprofitable.

Jan 1, 1981

By John E. Roberts

People are not a novelty. But the phenomenal numbers thereof, who have approached, settled, and been born in California in the past twenty-five years, are such a problem as to be a novelty in the broadest sense of the word. California, with less than 7,000,000 people in 1940, and over 19,000,000 in 1966. In 5 1/2 years, (1960-65) the southerly 14 counties of California, which together comprise one-half the land area of our state, had an increase in population greater than Colorado, or Arkansas, or Oregon, or any one of 19 other states.

Jan 1, 1967

By M. Machina

Anew approach to the use of projectiles for rock fragmentation uses recently-developed technology to optimize projectile shape and composition to achieve the desired type of breakage. Projectiles can also be made of various materials, as determined by the requirements of downstream processes. This paper describes laboratory tests with an 21-mm (8-guage) gun, and field tests with a 60-mm cannon.

Jan 1, 2003

By Carl (Original by) Hrovatic

Land is a precious resource and should be treated as such by all members of our society. The soil covering this earth is only a very thin outer layer, varying in thickness from a few inches to a few feet and covering the rocks and minerals lying beneath the surface. The wise use of this valuable commodity is the responsibility of everyone. Many everyday activities disturb e earth's surface. Examples are highway construction, housing and commercial developments, agriculture, and various types of mining. This chapter discusses the relationships of the environment to land as it applies to surface operations in the coal industry. Mining by surface methods disturbs, for a brief period of time, thousands of acres of land annually. In addition, refuse piles, slurry ponds, abandoned mine structures, unprotected mine openings, and unsightly cleaning plants can also adversely affect land unless properly handled.

Jan 1, 1981

By A. M. Gaudin

In the first place, let me thank you for inviting me to appear before you today to speak to you on "Mineral Industry Problems - Present and Future". It is a distinguished honor for me to have this opportunity, and I am highly appreciative of this distinction. The beautiful surroundings of Gatlinburg and the pleasantness of a summer occasion are a wonderful tonic for all of us, yet they should not blind us to the seriousness of our Industry's problems No doubt, because of my past appearances before members of the Society of Mining Engineers, at which I discussed wholly scientific topics, or research in the Applied Sciences, you may be expecting me to revert to these subjects. But I intend to venture in a field that is new to me, yet old to all of us, the field of Economics.

Jan 1, 1962

By Joel D. Hammond

Lightweight concretes date back to before the Roman Empire. The earlier concretes were made by combining a burnt lime for cementious material with pumice or volcanic rock for aggregate. Although structural value was limited due to its primitive nature, many structures were able to withstand the test of time. The rotary kiln expanded shale industry had a slow start that began around 1908. The industry was founded by Stephen J. Hayde of Kansas city, Missouri. Mr. Hayde noticed that the bloating effects of some aggregates were undesirable by the brick industry. Material of this type was considered waste and avoided in brick production, but he realized it had all the qualities and basic requirements for a concrete aggregate that would reduce weight and still retain structural value. It came into national attention by use in ocean-going vessels through a shipbuilding program undertaken by the united states Fleet Corporation. This research was brought about by the need to find a suitable material to replace high-grade plate steel due to a shortage created by World War I. The need prompted the government to supply the reserves that Stephen Hayde desired to continue and complete research into producing a uniform lightweight aggregate. His results pointed to the rotary kiln method for which he was granted a patent in 1918. One of the most famous and largest concrete ships built through this program was the U.S.S. Selma. Although the Selma

Jan 1, 1977

By T. E. Wilson

In conjunction with experiments to improve the particle size preparation of coal bore cores prior to washability testing, discrete-event breakage of coal, shale and homogeneous low-strength concrete cores was studied. Breakage of individual size classes by drop-shatter and by incremental tumbling in an end-over-end hand-driven tumbling cylinder revealed systematic changes in the breakage function, namely, that breakage in any size class diminishes as the number of events increases. The effect of the fines removal enhances the breakage of harder material (having lower grindability indices), but appears to have less effect for softer material.

Jan 1, 1998

By D. Nilsson

This paper demonstrates the importance of including a discount rate in the determination of the optimum final' depth of an open pit. Without a proper discount rate, a pit will probably end up too deep. Another consideration is future underground mining. If underground mining is profitable, the pit may need to be shallower. Of all of the investments needed, only mining equipment and the underground mine should be included, and amortization and depreciation should not he included in the study.

Jan 1, 1997

By Robert E. Haun

Retech's Plasma Arc Centrifugal Treatment (PACT) system is a thermal technology that uses heat generated by a plasma torch to treat hazardous waste containing metals and/or organics. Metal bearing solids and soil are melted by the process, and organic contaminants are thermally destroyed. The molten material forms a hard, glass-like leach resistant mass after cooling in a mold. This paper discusses plasma processing in general and presents some results of treating mineral processing wastes using the plasma arc centrifugal treatment process.

Jan 1, 1995