Search Documents

By Laurence E. Snow

The conversion to the use of commercial grade ammonium nitrate (CGAN) for use in blasting at the Utah Copper Pit of the Kennecott Copper Corporation has presented unique problems for the Drilling and Blasting Department, In order to better understand these problems, a' picture of the Bingham Pit might be helpful. Some quarter of a million tons of ore and waste must be blasted daily in order to keep thirty-eight electric shovels operating. All material is blasted by "toe holes" of 24 to 28 feet in depth, drilled from prepared drill grades and sloped so as to bottom approximately 5 feet below the bench level. Horizontal spacing of these holes averages 22 feet, with exceptions being made where faults occur in the bank. These "toe holes" are drilled by 4-inch drifter machines, mounted on self-contained mobile drill units using .3-inch starter bits and bottoming at a minimum of 2 1/2 inches in diameter, "Toe-hole" drilling amounts to about two-thirds of the total drilling. In the higher bank sections of the Mine and wherever necessary, single rows of "down holes" are drilled to 28 feet in depth and spaced, on the average 23 feet apart. These holes are also drilled by a mobile drill. "Down hole" drilling amounts to about one-third of the total drilling.

Jan 1, 1959

By W. A. Weimer

Coal and coal mining is no longer the mighty king of industry and in our daily lives and homes that it once had the privilege of commanding. Many of you will remember that one of the chores of your youth was to bring in the scuttles of coal, morning and night, to feed the heater or stoke the furnace in the morning and bank it at bedtime. Growth of gas and oil have displaced coal in home furnaces and commercial buildings, and have taken over some segments of industrial markets. The coal burning locomotives have virtually disappeared in favor of the more efficient diesel engine. However, coal as a prime mover still holds its strategic position as is evidenced by act that the electric power industry almost entirely depends upon coal for its generation.

Jan 1, 1961

By J. Andres

"Freeport-McMoRan’s Sierrita operations refines molybdenum disulfide in a ferric chloride leach to remove impurities. To understand bottlenecks in the leach process and the true capacity of the leach system, a cross-functional team was established to look at theoretical models, kinetics of the leaching process, equipment limitations and operational strategies. A series of in-plant tests were run which resulted in a road map for improved throughput. INTRODUCTION Molybdenum, a vital component in the steel industry, is often found in nature as molybdenum disulfide (MoS2). Molybdenum disulfide deposits can exist as standalone components in an ore body, or can also be found within copper porphyry nodes. Processing for these copper/molybdenum porphyry ore bodies involves a first stage of flotation to produce a bulk concentrate before separation of the copper and molybdenum concentrates in a second stage of flotation. In this second stage of flotation, a reagent is added to suppress the copper particles, while allowing the molybdenum disulfide particles to remain hydrophobic and continue to float. This separation is very good at keeping the molybdenum out of the copper concentrate; however a portion of the copper continues to float through the circuit. As a result, there is typically some amount of copper in the final molybdenum concentrate. This copper must be removed in order for the molybdenum disulfide product to meet product quality specifications. Once the raw molybdenum disulfide product has been made, a separate process must be applied to remove any copper, lead, or other impurities remaining in the concentrate. This process usually involves the selective leaching of impurities out of the bulk solid. Gupta mentions three specific types of leaching agents, sodium cyanide, ferric chloride, and hydrochloric acid for the removal of sulfide impurities. Sodium cyanide is useful for the removal of copper compounds such as bornite, covellite, and chalcocite.1 Sodium cyanide solution dissolves these copper compounds, and the remaining molybdenum solids are filtered to produce a pure molybdenum concentrate. Ferric chloride works similar to that of sodium cyanide, but is particularly efficient in removing chalcopyrite and galena compounds. These compounds are easily chlorinated at elevated temperatures, producing copper chloride and lead chloride, through the reactions presented below:"

Jan 1, 2015

By Robert L. Llewellyn

The Wharton No. 2 Mine of Eastern Gas and Fuel Associates is located about 60 miles south of Charleston, West Virginia in Boone County. Daily production is 6,000 T.P.D. on a two-shift basis. The Hernshaw Seam is mined by conventional equipment with one continuous miner in areas where conditions are suitable. The plant is on Cow Creek .Branch of Pond Fork, which in turn flows into the Little Coal River at Madison, West Virginia. When the mine was opened in 1948, plans were developed to build a dual Baum jig plant complete with mechanical and thermal drying, and because full production would not be reached for several years, it was decided to install only one Baum jig setup although the complete structure was erected. This phase of the plant was placed into operation early in 1949, The rated capacity was about 300 T.P.H. of 5" x 0 raw feed to the jig. Being a drift mine, the 10-ton mine cars are dumped at the Headhouse, crushed to 8" in a double roll crusher, conveyed 780 feet downhill to the picking .house where the +5" slate is removed by pickers. All coal is crushed to 5" and 5" x 0 is conveyed 150 feet to the cleaning plant. Further describing the plant growth, the second jig setup was installed in 1954 to clean the increased production. During this operating period, exhaustive tests had ,been run on the plant bleed which was an overflow from the large sludge tank located inside the plant, When the second jig addition was undertaken, 5-14' diameter and 12-8" diameter cyclones with a 9-disc filter were installed for the solids recovery and water clarification system, However, the circuit was not closed and a bleed of part of the overflows from the 8" diameter cyclones was still necessary, To comply with the State Water Commission regulations on stream pollution abatement, four pumps in series were installed to discharge the waste water behind the refuse pile.

Jan 1, 1959

By Burton E. Gilpin, Dr. George W. Annadale

A two level risk analysis procedure which is specially designed for use in river environments, is presented. The first level risk assessment (Level I) is often adequate for purposes of most projects, and entails hazard assessment, exposure identification, consequence estimation, and risk characterization. Two unique features of the method are the Composite Hazard Rating system, which is used in hazard assessment, and a formalized decision model for risk characterization. The risk characterization procedure provides information on the acceptability of risks, can be used to distinguish between the relative severity of risks, and to evaluate whether more advanced risk assessment would be required.

Jan 1, 1992

By R. H. Church

The Bureau of Mines' Tuscaloosa Research Center has developed a field test unit (FTU) which dewaters mine and/or mineral processing by-product slurries. The feed material (by-product slurry) is mixed with a known quantity and specific type of synthetic polymer (usually a polyacrylamide) to induce flocculation in a continuous operation. The flocculated material passes over a specific number and size of slotted stationary screens which separates the flocculated solid material from the "clean" water. The "static screens" are positioned at a fixed angle to maximize flow capacity and capture of the solids content. An investigation was conducted at an industrial crushed stone operation located near Birmingham, AL, to determine if the Bureau's FTU could successfully dewater the waste slurry generated during grinding and sizing operations at this facility. The investigation showed that waste slurries could be dewatered to 50 pct solids, at a polymer cost of approximately $0.85/ton of dry solids treated, and resulted in approximately 85 to 95 pct solids recovery. The dewatered material continued to consolidate and reached 69 pct solids in 24 h. Presently, the waste slurry generated at this facility is discarded into impoundments. However, this research has identified the recovered waste as an economically marketable product.

Jan 1, 1994

By Sharanappa Yalal, Rakesh Kumar Khali

"Himalayan geology poses the most challenging ground conditions almost anywhere in the world, one of the reasons thereof is their evolution as the youngest mountain chains. They are demonstratively rising faster than any mountain elsewhere. The composition is also younger, and consequently less well consolidated than the other older fold belts. This is consistent with the fact that they constitute one of the most active of the plate margin zones rising at a rate that is almost double the Andes, which is in turn three times that of the Alps. Thus, stress conditions (Magnitude and variations) can potentially be more extreme and adverse on a Himalayan tunneling project. Tunnel excavation under the Himalayan Mountains will pose significantly more challenges than an equal length and equal cover drive almost anywhere in the world. These in-depth-tunneling difficulties through high mountainous terrains have posed major challenges for application of traditional drill and blast (D&B) and NATM methods. Handling such adverse geology at any depth is always problematic and generally leads, if not adequately foreseen, to the significant tunneling delays. The author wants to highlight the challenges faced and on the spot solutions adopted while executing most prestigious 273Km long Udhampur –Srinagar- Baramula Rail Link Project (USBRL) in the Himalayas in the state of Jammu & Kashmir, India. The main focus of the paper is on main stretch of USBRL Project i.e. T-80 (India’s 2nd longest railway tunnel & 3rd longest in Asia) where the team of the author has recently completed a 11.2 Km long tunnel and where the train track has gone operational from Qazigund to Banihal. The construction of this stretch posed several challenges akin to highly adverse geological conditions. Executing on -the -spot solutions, the project has been completed successfully. 1.0 INTRODUCTION Construction of Udhampur-Srinagar-Baramulla Broad gauge railway line is one of the Mega projects undertaken by Indian Railways to establish a dependable transportation in the state of Jammu and Kashmir. In engineering terminology, it is a challenging project negotiating breakthroughs against the complex Himalayan geology. The Project which has been operational over last 12 years , stretch by stretch, is in advance stage of construction . The purpose of the prestigious project is to connect the Kashmir valley to the mainland of the state of the country. On the date owing to the hurdles of the tuff terrain, the transport of this part is totally dependent on the surface transport, i.e., through a road which connects NH-1A from Delhi to Srinagar. The altitude of the region varies from 500.00 to 1700.00, ranging through Udhampur to Katra - Reasi –Sangaldan- Banihal-Quazikund-Ananthnag-Srinagar-and Baramulla. The main features of this project are its Pirpanjal Tunnel and T-48 & 49 tunnels which cover the maximum length of tunneling through thick hostile geological conditions, the total length being 138km. Details of Pirpanjal tunnels are shown in Figure-1."

Jan 1, 2016

The engineering company's participation in quality assurance in the mining industry is twofold. Not only must it have such a program to ensure the necessary high standards for its own design and construction of a minerals processing plant, but it is also responsible as the "engineer" for both the selection and the quality of purchased equipment which goes into that plant. It is in this latter role that the engineer finds the most difficulty, or controversy, since while it is relatively easy to control his own performance, this is not ncessarily so when dealing with companies, all with their own ideas or standards. The engineer has perhaps rather reluctantly become more involved with the quality assurance of purchased equipment. This is because he has been used to writing performance type specifications and expecting the equipment manufacturer to provide the degree of quality, and control of that quality, for the product to meet the specified operating conditions. However, this has sometimes placed the manufacturer in a difficult position since to remain competitive in today's market conditions, he cannot always insist on product improvements or options which may in the long run be vital to reliable operation of the equipment.

Jan 1, 1982

By M. Misra

A sample of thorium-contaminated soil from Kirtland Air Force Base (AFB) was subjected to froth flotation for removing thorium contaminants. A series of flotation tests were conducted to screen and evaluate the reagents. Among the collectors used, sodium oleate exhibited to show the promising results. Preliminary tests showed that a concentrate having activity as high as 5300 pCi/g can be obtained from the contaminated feed soil having activity 800 pCi/g. The volume reduction obtained was 89% and the activity recovery in the concentrate was 68%. The paper discusses the physico-chemical characterization data and the potential physical separation decontamination schemes for the thorium contaminated soils.

Jan 1, 1996

By Joseph J. Garbarino

World demand for phosphate fertilizers has grown at an average annual rate of between 6 and 7 per cent over the past 10 years. In the next five years world demand is expected to at least continue to grow at that rate. Also, the continued need for improved fertilizer materials, coupled with improvements in fertilizer technology, have placed added importance on the use of phosphoric acid as a starting material for high analysis phosphate fertilizers. This demand for phosphates and phosphoric acid must be met by increased production. Increased phosphoric acid production also brings increased demand for chemical processing agents including foam control agents. We at Arizona Chemical Company have closely followed the phosphate fertilizer industries needs. Arizona Chemical Company has been an important supplier of flotation agents to the phosphate industry, primarily from its Panama City, Florida plant. We have also recognized the important role played by foam control agents in the wet-phosphoric acid manufacturing process. We feel it is the responsibility of the supplier of foam control agents to offer specifically designed products that are highly efficient and economically useful. The difficulties involved in evaluating foam control agents in the plant are recognized. Owing to the large number of variables present, and the difficulties in controlling these variables during the period of a plant trial, plant evaluation of a large number of foam control agents is impractical. We have attempted to develop a practical, reproducible, and yet rapid, laboratory evaluation test which correlates with plant performance.

Jan 1, 1966

By W. E. Sabina

In the short period of one mans? career we have seen specifications for bulk material handling systems and equipment grow from two or three pages to as much as two or three volumes for a single contract. The old 'short form' described what the purchaser expected the equipment to do. The long form does the same but also includes nut, bolt, and lockwasher depth of detail. What are the events that led to this proliferation of verbiage, and does it benefit the buyer in the final analysis? Is there a better way to purchase complex equipment while ensuring the highest quality for the dollar spent?

Jan 1, 1986

The need for an integrated approach to optimization of unit operations in both the pit and the mill has long been recognized, but the complexity and nature of the overall problem has up to now resisted solution. This paper reports on a modeling methodology which couples symbolic and numeric computing to unify operations in both the pit and mill. The ultimate goal of this work is to optimize all operations that are influenced by blasting. Blasting plays a key role in all facets of operations. Obviously, drilling and blasting costs are determined by blast design, but the down-stream costs that are closely related to blasting results are often treated as separate functions: loading, hauling, cleanup, and crushing and grinding are all heavily influenced. Diggablilty and bucket fill factor are a function of fragmentation, the condition of the floor and uniformity in the shape of the muck pile. Likewise, cycle times and loading delays partially determine haul cycles, while fragmentation distribution and size determines the efficiency of truck loading. Removal and breakage of oversize causes loading delays and increases cleanup costs. The influence of blasting doesn't stop at the crusher. Mill productivity, power consumption, and maintenance are a function of the feed. Even at the SAG mill a reduction of a critical particle size during blasting can increase throughput. Thus, a bottle-neck for production far removed from unit operations in the pit can be alleviated by a modification in blast design. The question is: how do we optimize blasting with respect not only to itself but to al\ related mining and milling operations? For that matter, how do we even model blasting so that we can control the results of a blast?

Jan 1, 1991

By David H. Carrillo

HYL has developed a sticking tendency test which accurately predicts behavior of iron oxide feedstocks in the HYL III process. Test results together with pilot plant experimentation and commercial scale demonstrations permit the conclusion that lump ores will not agglomerate at 960°C (1233 K) in an HYL III Plant. Pellets may also be processed without agglomeration at 960°C (1233K) with the addition of no more than 5 percent lump ore. Using the HYL III process, the ironmaker can exploit feedstock market conditions without sacrificing plant productivity or energy efficiency.

Jan 1, 1981

By L. F. Engle

There continues to be a certain magic attached to the word "Automation". When properly planned for, engineered, installed, and operated, the magic truly does take place - witness certain publicized mineral processing, metallurgical, and chemical plants. They operate successfully with few people, instead of previous dozens as in similar facilities not automated. Production quality has improved. Maintenance costs have been lowered. When such welcome results are achieved, it's proved to be a function of method and procedure in establishing criteria for choosing the intelligence and control systems followed by skilled choice of the specific elements used. The criteria, the bases for decision, are associated with design, construction, startup, operations, and maintenance. How to go about automating any process system to achieve the optimum profit depends on attention to all those aspects of a project. None of them can be forgotten if maximum satisfaction is to be gained. Control loops that look wonderful on an equipment. Piping, and Instrumentation diagram can suddenly turn into costly and. annoying problems in the field if there has been too little coordination of design. Panel boards that are literally works of art just before startup can become the largest of white elephants if an air header is inadequately sized and the pneumatic control circuits are sluggish. Conveyor belt replacement costs can skyrocket if a critical discharge chute far away from immediate operator attention lacks a simple yet effective clog-chute switch. Planning, execution, and followup of the work, the skills, and function of-the automating material can make any new project a success. An integrated owner contractor, producer-engineer approach is the key.

Jan 1, 1963

By Adrianus Halim, Jenni Hooli, Bartłomiej Skawina, Fredrik Sundqvist

Transitioning from diesel-powered loading and hauling machinery to battery-electric vehicles (BEVs) responds to the need for deepening underground mines as regulations become tighter. When using BEVs, exhaust gases and diesel particulate matter (DPM) emissions can be eliminated, and the energy required for the machines is used more effectively. Unlike their diesel counterparts, which are refueled, BEV loading and hauling machines — specifically, load haul dump (LHD) machines — can use battery swapping. This brings additional aspects to the operation that need to be considered, which have not yet been studied extensively. This study used discrete event simulation (DES) to analyze how the different numbers of BEV LHDs affect queueing and productivity when using different numbers of batteries and different swapping times in an underground block cave mine. The results identified the formation of working groups, where the machines swapped their batteries concurrently within each group, and their relation to the queueing time. Additionally, the minimum number of batteries per machine was identified to maximize productivity while minimizing queueing time. This study demonstrates DES as a powerful tool to assess and analyze conceptual systems and identify their underlying structures, which can enhance the deployment of BEV LHDs in underground block cave mine operations.

Apr 1, 2025

By S. C. Westerfeld

The original patent for the gyratory crusher was granted to Philetus W. Gates in 1881. This first crusher was used by the Buffalo Cement Co. At the time these early gyratory crushers were developed all mining and quarrying, either underground or open pit, was done by hand; tonnages generally were small and product specifications simple and liberal. Likewise plants were small and demands for small product sizes practically nonexistent. In addition to substantial amounts of hand labor, the available material handling equipment was small, simple, and not suited to handling large run of mine ore. Mine can, cable ways, or belt conveyon transporting crushed material to the mill had limited capacity per hour. At the turn of the century the largest Gates crusher, the No. 9, had a receiving opening of 21 x 48 in. with a three-arm spider and a 21 x 80-in. opening with a two-arm spider. The steam shovel began to change the entire picture of open pit quarrying. As a result of the use of steam shovels around 1910 crushers with 48-in. receiving openings were built; thus it can be seen that the basic gyratory crusher was developed prior to World War I. The improvement of the internal combustion engine and the use of pneumatic tires created a new set of operating conditions. Early mines were small, using shrinkage stoping and small mine can. The capacity of material handling was small, limiting the size of the largest piece and the feed rate. Improved material handling resulted in more and more large open pit mines with large shovels and a tremendous increase in the size of off road or mine haul trucks or rail can. Primary gyratory crushers also increased with receiving openings as large as 60 in. and connected hp of 1,000.

Jan 1, 1985

In 1992, United States mine production of barite decreased 8.5%. Barite consumption, sold or used by grinding plants, decreased by 36.9% and imports decreased by 61.6% vs. 1991. World mine production decreased 1.5%, according to the US Bureau of Mines. The value of domestically produced barite, f.o.b. mine, decreased 11.9% according to the Bureau. The declared value, c.i.f. United States port, of all imported crude barite during 1992 decreased from $42.35/t ($38.42/st) in 1991 to $40.09/t ($36.37/st). Nevada continued to be the leading producer of barite with 88% of the total, followed by Georgia and Missouri. It is estimated that 80% of the domestically mined barite was used as a weighting agent in drilling fluids. The remaining 20% was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia and Ten¬nessee was used in the non-oilfield sector. Of the total barite used by grinding plants and chemical manufacturers, it is estimated that 90% was used in drilling fluids and 10% in the non-oilfield sector. This included barium chemicals and fillers in paper, plastics and glass. The tonnage consumed in the drilling fluids market decreased due to the lower average rig count during 1992. The average number of rotary rigs operating (717) was 16.6% less than the 1991 average of 860 in the United States. Crude barite imports were 518 kt (571,000 st), 61.6% less than in 1991. Imports accounted for 44.7% of the barite consumed (apparent) in the United States. During the year, China continued to be the leading exporter of crude barite ore to the United States with 67.2% of total crude ore imports. India followed with 31 %, and others with 1.8%. About 90% of the imported barite ore was used in the oilfield sector. Ground barite imports decreased from 46.3 kt (51,000 st) to 30.9 kt (34,100

Jan 1, 1993

By L. F. Zeiler

In the past, health concerns in coal mines have primarily centered on those elements which have been essentially inherent to the mining environment. These would include respirable coal mine dust, respirable crystalline silica, excessive noise levels, and diesel exhaust particulates. Commercially-available chemical products are prevalent on mine property. These potentially toxic materials are chemical formulations that can degrease, clean, and lubricate metal parts, separate coal from rock in float/sink operations, and aid in roof consolidation, among other uses. As the general public has become more aware of the hazards of chemical exposures, miners have likewise become more concerned about working with an ever-expanding variety of chemical products on the job. Often, product or chemical specific hazard communication training is inadequate or ineffective, and miners do not know exactly what the ingredients are in the products they handle, or the health hazards involved with their use or misuse. Currently, the Mine Safety and Health Administration (MSHA), by law, enforces 1972 Threshold Limit Values (TLV). MSHA is making preparations to adopt new personal exposure limits for enforcement. The values given throughout the article are 1994 TLV's and are not enforcement standards, but are used for discussion purposes. They reflect the current scientific thinking regarding personal exposure to these chemical agents. An overview of these products is presented, and the potential health hazards associated with their use are discussed. Controls needed to prevent overexposures, such as proper handling procedures and personal protective equipment, are covered. Methods used to collect and identify contaminants are presented.

Jan 1, 1995

By Terry O. Arney

Ore Reserve Models are well established evaluation and mine planning tools. BY definition, these models are made up of regularly sized blocks, arranged in a three dimensional matrix. Two dimensions correspond to north and east directions, and the third, to the depth or elevation. The dimensions of the blocks need not be equal, but generally at least two of the dimensions are equal. The blocks are located in space by coordinates which are generally translated into index values for computer applications. Each block will have quantitative attributes, such as grades, densities, rock characteristics, etc. assigned to it. The process of assigning values to each block in the three dimensional matrix is the process of ore reserve model development. One of several interpolation procedures may be employed to predict the value of a block, based on surrounding data. Block value models have several uses. The utilization of block models in ore reserve computations is quite common. Here, ore reserves may be calculated by level or by cross-section for the entire deposit. For each ore reserve calculation, multiple cut-off grades may be analyzed to determine the ore reserves under different cut-off conditions. The other major use of block value models is in mine simulation. Through simulation, profitable studies that analyze the effect of alternate ore removal sequences can be undertaken to determine economic optimality. Other studies that are undertaken in mine simulation problems include the evaluation of mine layout, pit slope effects, and the impact of varying cut-off grades.

Jan 1, 1974

By H. Cetin

The availability of coal resources of selected 7.5-minute quadrangles of southwest Indiana was examined in this study. Resources were defined as original coal in place, remaining after mining, and currently available considering land-use and technological restrictions. The amount of coal mined from each study area varies depending on the mining practices of the companies operating within the area. Of the three quadrangle investigations, the available resources range from 50 percent to 79 percent of the original resources. Most of the coal resources under deep-minable category were not available because of technologic restrictions, such as insufficient coal thickness.

Jan 1, 1996