Search Documents

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"The U.S. National Institute for Occupational Safety and Health (NIOSH) has been researching refuge alternatives (RAs) since 2007. RAs typically have built-in pressure relief valves (PRVs) to prevent the unit from reaching unsafe pressures. The U.S. Mine Safety and Health Administration requires that these valves vent the chamber at a maximum pressure of 1.25 kPa (0.18 psi, 5.0 in. H2O), or as specified by the manufacturer, above mine atmospheric pressure in the RA. To facilitate PRV testing, an instrumented benchtop test fixture was developed using an off-the-shelf centrifugal blower and ductwork. Relief pressures and flow characteristics were measured for three units: (1) a modified polyvinyl chloride check valve, (2) an off-the-shelf brass/cast-iron butterfly check valve and (3) a commercially available valve that was designed specifically for one manufacturer’s steel prefabricated RAs and had been adapted for use in one mine operator’s built-in-place RA. PRVs used in tent-style RAs were not investigated. The units were tested with different modifications and configurations in order to check compliance with Title 30 Code of Federal Regulations, or 30 CFR, regulations. The commercially available relief valve did not meet the 30 CFR relief pressure specification but may meet the manufacturer’s specification. Alternative valve designs were modified to meet the 30 CFR relief pressure specification, but all valve designs will need further design research to examine survivability in the event of a 103 kPa (15.0 psi) impulse overpressure during a disaster. BackgroundThe Mine Improvement and New Emergency Response Act of 2006, known as the Miner Act (U.S. Department of Labor, 2006), was enacted in the wake of three mine accidents involving explosions or fire that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the Miner Act includes provisions that target mine safety issues in areas such as emergency response planning; adoption of new technology; training and education; and mine safety standards enforcement. Section 13 of the Miner Act specifically directed the U.S. National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of refuge alternatives (RAs) for underground coal mines, and the U.S. Department of Labor to act on the results of such research, as appropriate. These mandates culminated in the 2009 adoption of changes to the Title 30 Code of Federal Regulations, or 30 CFR, mining health and safety regulations (U.S. Department of Labor, 2008), requiring underground coal mines to supply mine emergency RAs and associated components so as to provide a life-sustaining environment for persons trapped underground. Such RAs can be either selfcontained mobile units or built-in-place facilities. The regulatory changes also include provisions establishing requirements for the approval of RAs and their components by the U.S. Mine Safety and Health Administration (MSHA), among which are numerous criteria for providing a safe breathable atmosphere under positive pressure within the RAs. One criterion for maintaining a safe RA atmosphere is the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (specified as 0.18 psi, or approximately 5.0 in. H2O), or as specified by the RA manufacturer, above mine atmospheric pressure in the RA (U.S. Department of Labor, 2008)."

Oct 1, 2016

By Thomas O’Neil

Part 2 of this article continues with a discussion of features that distinguish contemporary investment analysis in mining from earlier methods. Part 1 traced the evolution of evaluation methodology from the traditional and discounted cash flow methods to the present. Quantitative investment models of the past 20 years played an important role in mine evaluation, but a new integrated approach to mine investment decision-making is now developing because of growing economic, technical, and political uncertainties. One of those uncertainties -inflation-was discussed in Part 1. Increased Risk At a time when mineral production technology and analytical evaluation tools have never been more sophisticated, it may seem anomalous to claim that mining ventures are riskier. Whereas technical risk has, indeed, been notably reduced, business risk the chance of a major loss due to market factors-has increased. This has been caused by two factors: the rapidly rising capital requirements of new projects and increasingly unpredictable future economic conditions. These difficulties are compounded by the long lead times of large, new mining projects. Rising Capital Requirements A $100 million investment is no longer considered to be a large mining project in most cases. For a large metal mining project, the total cost of the concentrator alone can exceed $100 million. Amoco Minerals' Thompson Creek molybdenum mine being developed in Idaho will cost over $350 million, for a relatively modest sized (23-kt/d or 25,000-stpd) ore operation with no extraordinary features. For a major grass roots copper operation producing blis¬ter or refined copper, the capital requirements are billions of dollars, not millions. Project costs are higher for two reasons. One, the projects themselves are larger; and two, the capital cost per unit of production is rising rapidly. Projects are larger because lower grade ores, yielding smaller margins, must be mined in greater volume-particularly in view of the high fixed costs of modern technology. When analysts contemplate any capital project, an important consideration is the minimum economic size of the facility. This is the smallest size that can be built and still be competitive on a total unit production cost basis. In the conventional copper smelting business, for example, a production rate of at least 91 kt/a (100,000 stpy) of blister copper is about the absolute minimum for reducing unit fixed costs to competitive levels. Clearly, many variables affect the minimum economic size of a mining facility, but with few exceptions that size continues to grow. Unit capital costs of new mining projects also are continuing to rise. The accompanying table shows that the capital costs in primary copper production have risen faster than the cost of living. Of particular note is the capital charge of over $1.70/kg (77411b) required for a new, fully integrated facility in 1981. Thus, the mid-1982 copper price would not even cover the cost of capital for a new copper producing complex without considering the direct operating costs for such a facility. The breath-taking costs of new mining projects are caused by factors such as increasingly complex technology, the rising social costs of creating attractive living and working conditions for employ¬ees, and the expenditures re¬quired for environmental protec¬tion. For whatever reasons, how¬ever, unit capital costs in mining continue to exhibit staggering growth rates. Future Economic Conditions Risk is not only a function of the size of the potential loss-an im¬portant measure of which is the capital intensity of mining dis¬cussed above-but also of the like¬lihood of incurring the loss. It is here that the ever increasing lead times of mining projects and the glaring limitations of economic forecasting are so important. In comparison to nearly all other in¬vestments, mining has more capi¬tal at stake for a longer period of time before commercial uncer¬tainty is resolved by distant eco¬nomic conditions that are subject to high forecasting errors. A sobering example of the pre¬ceding points occurred with the Lakeshore copper mine in south¬ern Arizona that Hecla Mining Co. undertook to finance and manage in 1969. The project was a joint venture of Hecla and the El Paso Natural Gas Co. and included two mines-one producing oxide ore and a second in the sulfide zone¬and a complex processing facility producing both electrowon cop¬per cathodes and copper precipi¬tates. The project originally was

Jan 12, 1982

By KALLAM VK REDDY, VADAPALLI SANJANA, Veerendra Singh, Gajanan Kapure

Mining activity around the world has increased significantly to meet stepped-up demand for various metals [1]. Apart from the target minerals, mining also generates huge amounts of unwanted minerals that exit the mines as overburden. Due to the active mining activity, high-grade mineral resources are being depleted, leaving inferior-quality ores [2]. The mining of low-grade ores further increases the amount of overburden/waste per ton of metal equivalent of ore mined. Currently, overburden and other mine waste is most commonly used in the construction industry and as feedstock for making cement and concrete, but the overburden can also be used as a source of valuable minerals and metals [3]. 

By Robert D. Hansen, Richard R. Klimpel

INTRODUCTION A very important factor in froth flotation is the use of surface-active chemicals to form a froth in which minerals or coals are retained, thus allowing for valuable component enrichment. In coal flotation reagents (frothers) specifically designed to provide an efficient froth are employed. It is this group of chemicals that will be the primary emphasis of this paper. Despite the importance of frothers, surprisingly little systematic scientific work has been performed with the goal of quantifying frother mechanisms and the influence of particles on froth stability. Based on direct experimental observations in both batch laboratory and continuous large-scale flotation cells, the use of a frother significantly increases first, the possibility of a particle- bubble contact, and second, the efficiency of sticking after such a contact. Thus, a major role of a frother is to significantly increase the rate of flotation. This rate modification by a surface-active agent occurs through several observable mechanisms including the formation of a froth of relatively consistent character (bubble size and bubble density) under a variety of operational conditions, an increase in the ability to disperse air in the flotation cell, a reduction in the rate of coalescence of individual bubbles in the cell, and a decrease in the rate of bubble rise to the pulp surface. It will not be the intention of this paper to exhaustively list all frother accomplishments related to research, development and use in coal flotation. Rather, the authors will attempt, based on their experience, to present a technology overview of the role of frothers in the chemistry of flotation as successfully practiced at the industrial level. A very useful framework for flotation is the concept suggested by Klimpel (1984, 1984a) of viewing flotation as a system consisting of three major components: chemistry, equipment and operating variables. This is illustrated in Figure 1. A major point of this figure is that flotation is a highly interactive system with many technical and economic combinations of component settings available to operators to achieve a given goal. Sometimes simultaneously changing various component settings will reinforce a particular attribute. Also various component settings can cancel or counteract each other if changes are not chosen wisely. Thus, coal flotation must be viewed by the plant operator as a complex system with the economic/technical optimization of a given flotation process being directly related to the operator's knowledge of how his particular flotation system behaves as a function of the major control variables he has at his disposal. Typical important component settings in coal flotation are collector dosage, frother type and dosage, air flow rate, feed rate, particle size, pulp density, and the surface oxidation conditions of the coal. Because of the above complexities, it is sometimes assumed (especially in laboratory studies) that the choice of frother type and dosage is not as crucial as some of the other factors such as collector type and dosage (e.g., Leja, 1982). Detailed plant level testing of all of the factors of Figure 1 performed in recent years, Klimpel (1980, 1980a, 1982, 1984, 1984a), Hansen (19861, Klimpel, Hansen and Meyer (1982), simply do not support this assumption. The above testing has shown rather clearly that certain frother chemical structures consistently exhibit predictable performance characteristics in both mineral and coal flotation. In addition, significant changes in both rate and recovery can be expected. In the remaining sections of this paper, the following topics will be covered: requirements of chemicals capable of use as frothers, types of chemicals used commercially as frothers, some general performance characteristics of existing commercial frothers, and recent work in developing new frother chemical structures.

Jan 1, 1986

By K. A. Natarajan, Namita Deo

The interaction of Bacillus polymyxa and minerals such as hematite, corundum and quartz resulted in significant surface chemical changes, both on the cell surfaces and on the interacted oxide minerals. After such treatment, quartz was rendered relatively more hydrophobic, while hematite and corundum were rendered more hydrophilic. Biopretreatment was observed to be beneficial in the separation of silica from hematite and alumina by both selective flocculation and flotation. The possible role of bacterial adhesion and metabilites in the biobeneficiation process is illustrated.

Jan 1, 1998

By John F. MacDonald, John W. Critchfield

This paper describes the shield excavation of twin transit tunnels, through soft ground, in downtown Seattle. The tunnels are 6.5 m (21.25 ft) diameter and 1525 m (5000 ft) long. Initial support consisted of expandable precast concrete segments, followed by a final lining of cast-in-place concrete. Waterproofing was provided by a PVC membrane installed between the initial support and the final lining. During the course of the excavation a variety of methods were used to control the ground and limit settlement. These included deep wells, vacuum well points, eductor wells, chemical grouting, compaction grouting, jet-grout underpinning, and extensive instrumentation.

Jan 1, 1989

By R. Sripriya, Ch. V. G. K. Murty, N. D. Rao, P. V. T. Rao, A. Ramu

Studies were carried out to improve the performance of hydrocyclones at Tata Steel's chrome ore beneficiation plant in Sukinda, India. The optimal cut point of the hydrocyclones was determined in the laboratory using a stub cyclone. In the tests, the operating and design variables, including spigot diameter, density of feed slurry and inlet pressure, were varied. Subsequently, plant trials were carried out, and attempts were made to develop a model of the hydrocyclone using the Rao, Lynch and Plitt model. The cyclone efficiency was represented by the parti¬tion curve, and the performance was evaluated mathematically from a reduced efficiency curve, represented by the equation:

Jan 1, 2000

By Chris Chmura, Ketut Karmawan, Ian J. Duckworth

P.T. Freeport Indonesia operates a mining complex located in the highlands of West Papua, Indonesia. Present production from PTFI’s DOZ Underground Block Cave Mine is approximately 40 thousand tonnes per day (ktpd). This paper describes the design process and recommended ventilation infrastructure necessary to expand the DOZ Mine reserves and to increase sustained daily production above 50 ktpd. The enlarged footprint will feature longer production panels of up to 650 m in length, more active draw points, a second large gyratory crusher, and additional men and mobile equipment. The increased ventilation capacity will be achieved through the development of new, dedicated ventilation drifts, and primary Underground exhaust fans.

Jan 1, 2005

By M. R. Shahan, C. E. Seaman, S. E. Mischler, T. W. Beck

"Float coal dust is produced by various mining methods, carried by ventilating air and deposited on the floor, roof, and ribs of mine airways. If deposited float dust is re-entrained during a methane explosion, without sufficient inert rock dust quantities, this float coal dust can propagate an explosion throughout mining entries. Consequently, controlling float coal dust is of critical interest to mining operations. Rock dusting—adding inert material to airway surfaces—is the main control technique currently utilized by the coal mining industry to reduce the float coal dust explosion hazard. To assist the industry in reducing this hazard, NIOSH’s Pittsburgh Mining Research Division (PMRD) initiated a project to investigate methods and technologies to reduce float coal dust in underground coal mines through prevention, capture, and suppression prior to deposition. Field characterization studies were performed to determine quantitatively the sources, types, and amounts of dust produced during various coal mining processes. The operations chosen for study were a continuous miner section, a longwall section, and a coal handling facility. For each of these operations, the primary dust sources were confirmed to be the continuous mining machine, longwall shearer, and conveyor belt transfer points, respectively. Respirable and total airborne float dust samples were collected and analyzed for each operation and the ratio of total airborne float coal dust to respirable dust was calculated. During the continuous mining process, the ratio of total airborne float coal dust to respirable dust ranged from 10.3 to 13.8. The ratios measured on the longwall face were between 18.5 and 21.5. The total airborne float coal dust to respirable dust ratio observed during belt transport ranged between 7.5 and 21.8. INTRODUCTION During the extraction of coal, various dusts are produced that can be classified into two categories of interest: respirable and float coal dust. Respirable dust (diameter 10.0 = µm) has the capability to penetrate beyond the terminal bronchioles and become deeply embedded into the human lungs, leading towards respiratory disease complications (Potts et al., 1990). Float coal dust is defined as coal dust having a diameter less than 74 µm (Harris et al., 2009). During the mining process, float coal dust can be deposited on the floor, roof, and ribs of mine airways. With the proper mixture of methane gas (between 5% and 15%) and an ignition source, a methane gas explosion can occur (Barker and Humphreys, 1996). The resulting explosion can develop a pressure wave which lifts the deposited float coal dust material into the air, propagating a disastrous coal mine explosion (Harris et al., 2010). The current technique to safeguard against the propagation of a coal mine explosion is to treat the mine airways with incombustible rock dust (typically limestone), maintaining an 80% total incombustible content of the deposited material. NIOSH initiated a project to investigate control technologies that could be aimed at reducing the amount of float coal dust allowed to deposit in the mine airways using three approaches: prevention, capture, and suppression prior to deposition. Reducing the float coal dust being generated during the mining processes and capturing or suppressing airborne float coal dust prior to deposition would in turn increase the efficiency of the applied rock dust used to prevent mine explosions."

Jan 1, 2017

By S. Šolar

The countries of Southeast Europe are rich in aggregates, but neither management nor supply are coordinated within or across this area. There are open issues in SEE on the local scale as well as on regional/national and transnational scales that will need to be addressed in order to meet societal expectations related not only to the security of aggregates supply for economy, but also those linked to environmental concerns and social issues. The Sustainable Aggregates Resource Management project (SARMa), an EU Southeast Europe (SEE) activity, has as its objectives the development of common approaches to sustainable aggregate resource management (SARM) and sustainable supply mix (SSM) planning in SEE. In this paper we describe the SARMa project structure and report results for Work Package 3 activities pertaining to best practices for environmental management, the reduction of illegal quarrying, and the promotion of recycling of quarry wastes, construction and demolition wastes and other materials.

Jan 1, 2011

By K. E. Yassin, A. Yehia, M. Amar

Phosphate ores are the source of many commodities, such as phosphorus element, P2O5 and fertilizers. Discarding a large percentage of fine phosphate particles produced as slimes during phosphate ore processing represents a severe environmental problem, besides making the beneficiation process uneconomical. The phosphate industry is interested in a process that is efficient, with high grade and high recovery; ensures economical feasibility, with low operating cost; and is environmentally sound, with low toxicity. Numerous investigations have been conducted to try to find better processing techniques and reagents. However, reagent requirements and recovery limitations may be so high that the end does not justify the means. Reagents of biological origin are of special interest because they offer specific interactions with minerals, reduced operating costs, environmental acceptability and flexibility in adaptation. Recently, there has been a growing interest in using microorganisms as flocculants for mineral fines and as flotation collectors. 

By Jon Kellar, William Cross, Eric Swanson, John Starkovich

Zirconium tungstate (ZrW2O8) is a unique material with a negative coefficient of thermal expansion. In order to fully utilize this material as a filler, a surface treatment needs to be developed to better improve the wetting and dispersion capabilities of the filler. This paper describes an initial study to characterize the filler as well as investigate fatty acid and silane surface treatments for eventual compounding with thermosetting matrices. It was found that ZrW20, has a point-of- zero charge between pH 2.7-3.0, and that both fatty acid and organofunctional silane treatments appear to be viable surface treatments for this unique filler.

Jan 1, 2003

By J. Engel

The talc deposit in Gemerská Poloma lies 350 to 400 m under the surface; the whole deposit is located at the highest-level drinking-water-source protection zone, therefore, opening in this mining area (a well, a ramp) requires higher investment, operational and water protection costs. The adit, outside the mining area, with a length of 4200 m, rising with a gradient of 3? and a diameter of 10.3 m2, allows free passage/runoff of mining-water through the adit, and guarantees low costs for transporting produced material and equipment. This solution is in total less demanding from both investment and operational point of view.

Jan 1, 2007

By Patrick J. Coughlin

Shortly after Asarco Inc. purchased the Ray Mines Division from Kennecott in 1986, the company began an expansion program to increase copper production. The Bechtel Corp. oversaw engineering procurement and construction management for a new in-pit crusher, overland conveyor system and concentrator facility. Construction started in May 1990 on these facets of the expansion project. The concentrator was commissioned in February 1992. The Ray concentrator uses a single-line, semiautogenous grinding circuit (SAG) with a design through¬put of 27 kt/d (30,000 stpd). In the early 1960s, Kennecott conducted pilot plant grind tests of Ray mine ores to determine their amenability to SAG and autogenous grinding methods. Those tests, though, were not followed up. During 1973 and 1982, Kennecott conducted additional pilot testing on some of the softer ore types. In 1989, Asarco ran a final series of SAG pilot grinding tests at Lakefield Research, which became the basis of the new Ray concentrator grinding circuit. Even though pilot test work demonstrated that some of the Ray ores gave satisfactory results during the autogenous grinding tests, the SAG option was selected for the primary comminution device. Due to the wide range of mineralogies encountered in the Ray ore body, selective mining and blending of these ores would be required to achieve the necessary production efficiencies and throughput rates using an autogenous grinding circuit.

Jan 1, 1994

By Carlton H. Baab

In June, 1981 the Electric Power Research Institute (EPRI) issued a report titled "Control Systems in Coal Preparation Plants" to determine the status of instrumentation and automation systems in the coal preparation industry. EPRI concluded that the control systems presently being employed in the U.S. coal preparation plants "are relatively primitive compared with those in other mineral processing industries; and analytical instrumentation is virtually non-existent". Until recently, clean coal has had a low selling price and satisfying the purchasers' specifications required only minimum cleaning. However, it is becoming more apparent that the increases in coalfired utility power plants forced outage rates are relative to the deterioration in the quality of fired coal. Utility companies are becoming aware of the economic value of reducing the variability of ash, moisture and sulfur in steam coal purchase orders. New contracts are currently being negotiated between electric utilities and coal producers that include provisions for increased penalties if the product does not meet specifications. With tighter specifications on the quality of steam coal, interest is increasing in more sophisticated control systems. One type of device that is currently assisting the preparation plant operator optimize and control the coal cleaning process is nuclear based instrumentation. Nuclear instrumentation includes methods for measuring weight, level, and density as well as for performing elemental analysis on coal. This paper discusses the various types and applications of nuclear instrumentation currently in use in the coal preparation industry.

Jan 1, 1983

By Rusty Winn

"R.E. Janes Gravel Co. is an aggregates producer is located along a paleo-channel of the Ogallala formation (locally known as the Slaton Channel) approximately 48.3 km (30 miles) southeast of Lubbock, TX. In an attempt to beneficiate the 25.4-mm (1-in.) concrete aggregate product, a log washer was installed in the processing line to liberate and remove fines (clay) from the finished product. The introduction of this extra cleaning step increased fines in the finished product, exacerbating the original problem. Several other processing options were investigated before a geological analysis was undertaken to try and define the lithology of the formation and formation characteristics in an attempt to alleviate this problem.Initial assessmentsThe mined resources are mid-Miocene to early Pliocene (16-4 mya) in age and is the eastern exposure of the Ogallala formation of the Southern High Plains escarpment. The Ogallala formation consists of coarse-grained alluvial sediments in paleovalley channel ways from the Rocky Mountains with fine Aeolian and paleosol deposition on the uplands across the High Plains region of the United States. Locally, these Rocky Mountain sediments from New Mexico were transported and deposited in a paleochannel that is approximately 0.805 km (0.5 miles) wide and 15.25 to 18.3 m (50 to 60 ft) in depth. As this channel cut across the Southern High Plains it eroded local rock sources of Late Cretaceous limestones and Triassic sandstones and mudstones incorporating them into the younger Ogallala depositional sequence.Depositional historyThe channel currently being mined is a nontypical Ogallala deposit. The Ogallala in the panhandle of Texas is divided into two units, the Couch and the Bridwell. The Couch is the older of the two and exhibits alluvial sedimentation of thicker and larger gravel (up to 76.2 mm or 3 in.) deposits fining upward to Aeolian sedimentation and thick friable caliche deposits. The Bridwell overlies the Couch and is characterized by alluvial sedimentation, a distinctive red tint and smaller gravel components (typically no larger than 25.4 mm or 1 in.) fining upward to Aeolian sedimentation and thick, well-indurated caliche cap. The Slaton Channel divides these two units and shares lithologic components of both, yet is lithologically distinct due to its Cretaceous Age limestone gravels that can be < 3.66 m (12 ft) in size. Caliche/calcrete is a calcareous (CaCO3) deposit that forms in the B horizon of soils as a rain water leachate of CaCO3 from the upper A horizon."

Jan 1, 2014

By N. K. Davé

Water quality impacts of shallow water submersion of partially weathered and oxidized waste rock containing reactive sulphide minerals were investigated in laboratory column lysimeter studies. The waste rock investigated was highly reactive, contained oxidation reaction products from previous exposure and weathering, and had a low sulphur content of approximately 2 % S, mostly as pyrite. The submerged waste rock, though previously weathered, had high oxygen consumption, resulting in rapid depletion of dissolved oxygen in its pore water, within a shallow depth of ~2?5 cm from the surface. The surface and pore water qualities of the submerged waste rock were significantly impacted by the dissolution and release of previous-oxidation-reaction products, which contributed to their rapid acidification and having increased concentrations of dissolved SO4, Fe total and other metals: Al, Mn, Ca, Cu, Ni, Zn and Pb. Despite the high porosity and permeability of the waste rock, the diffusion controlled mass transfer from the submerged waste rock to the overlying water cover was relatively low for most ionic species. Additional surface oxidation of the sub-merged, partially weathered waste rock was on-going, but its impact on the overall surface water quality was low and masked by the dissolution and release of previous oxidation reaction products to both surface and pore water regimes.

Jan 1, 2006

By Changhong Huang, Y. J. Wang

This paper describes the formulation of mine ventilation network optimization as a standard nonlinear programming problem and the solution of the problem using the generalized reduced gradient (GRG) method. In general, the GRG method is regarded as one of the most effective and efficient methods for solving large-scale nonlinear programming problems. The variables considered in the network optimization include air quantity, regulator pressure loss, and fan pressure for each branch. Each of the variables is constrained by lower and upper bounds. This facilitates proper assignments of ventilation requirements and provides a great flexibility to include various situations encountered in mine ventilation. The objective of the network optimization is to minimize the overall air power consumed by or supplied to the network; whereas the constraints are, in addition to the variable bounds, the two fundamental network laws: Kirchhoffs voltage law and Kirchhoffs current law. A computer program has been developed based on the GRG method for the network optimization. An example of network with 18 branches, 8 regulators and 3 fans is included for illustration.

Jan 1, 1993

By John S. Thayer, Frederick E. Brinckman, Kenneth L. Jewett, Gregory J. Olson

Interest and research in biorecovery of metals has focused mainly on cell-based metal leaching and precipitation. However, production of non-enzymatic metabolic products by microorganisms related to metals bioprocessing also deserves attention. For example, it is well known that biogenic inorganic (e. g. H2S04 ) and organic acids play a role in metal dissolution. There are other metabolic products of microorganisms which can catalyze useful metals transformations. These include methylated metabolites such as alkyl halides which can dissolve metals from ores and also reduce certain metal ions in solution to pure metallic particles. This paper describes some of our research on metal dissolution and precipitation by such metabolites. Examples include the production of high purity elemental metal particles of gold, platinum and palladium by volatile metabolic products.

Jan 1, 1989

By E. Westman

Geographic Information Systems (GIS) are becoming a more commonly used tool for resource estimation as they provide not only a database management platform, but also the graphical capabilities to visualize resource characteristics. Interpolation methods used commonly in these resource studies do not typically provide a quantitative answer to the question: "How accurate is the estimate?" By comparing localized measurements at several locations to the interpolated thickness distribution used in a resource estimate, a quantitative analysis of accuracy can be obtained. The technique is demonstrated with a case study from Central Appalachia.

Jan 1, 1999