Search Documents

By I. Ward, E. Milosavljevic, M. Botz

"The silver nitrate titration method is a rapid and acceptably accurate means of analyzing for cyanide in leach solutions that contain primarily free cyanide. However, in leach solutions containing elevated levels of copper, the titrimetric method overestimates the concentration of free cyanide and underestimates the concentration of weak and dissociable (WAD) cyanide. The authors have developed a modified potentiometric (MP) titration method for determining WAD cyanide that overcomes issues associated with high copper levels in solution. The new MP-WAD method involves addition of a chemical ligand to the sample prior to silver nitrate titration to release cyanide bound to copper. Once released from copper, cyanide in solution is no longer affected by the presence of copper, and titration results are quantitative rather than empirical. In multiple laboratory trials with synthetic solutions and complex actual leach solutions, analytical results obtained with the new MP-WAD method were found to be within about ±5% of analyses obtained with the USEPA OIA-1677 WAD cyanide analytical method.IntroductionThe silver nitrate titration method is widely used to estimate the concentration of cyanide in leach solution for purposes of cyanidation process control. Cyanide determined by silver nitrate titration is commonly referred to as “free” cyanide, but frequently should be referred to as “titratable” cyanide. By definition, free cyanide is the sum of the concentrations of aqueous hydrogen cyanide HCN(aq) and the cyanide anion CN- (ASTM, 2010). Titration will only yield a reasonably accurate measurement of free cyanide when metal-cyanide complex concentrations (e.g., cadmium, copper, mercury, nickel, silver and zinc) in solution are low. In other words, titration will only yield a reasonably accurate measurement of free cyanide if the solution primarily contains free cyanide."

Jan 1, 2015

By Raymond W. Henn

The 32nd annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, June 13-17, 2011. The field demonstration portion of the course was conducted June 16 at Baski Inc.?s yard in Denver, CO. The full-scale field demonstration presents many types of drilling and grouting equipment in operation as well as numerous grouting methods per-formed under various field conditions. As part of the field demonstration, the class was shown the proportioning, mixing, testing and injection of various cement grout mixes into sand columns under controlled and recorded conditions. These sand column demonstrations have been conducted under controlled and measured conditions each year since 1999 as part of the short course. The sand column demonstrations were conducted prior to 1999, but with less quality control and minimal record keeping of the proportioning, mixing, testing, injection pressures and the final permeation results.

Jan 1, 2011

By Rolando Gonzalez

Mexico’s role in the world economic community continues to grow. And it is important that the country makes use of its natural wealth, including its large underground deposits of minerals and metals. With that in mind, Industrias Peñoles S.A. de C.V.(Peñoles), a mining, smelting and refining company, began mining lead, zinc and other metals from the Francisco I. Madero Project (FIM). The mine is located about 600 km (370 miles) northwest of Mexico City in the state of Zacatecas. Peñoles plans to remove about 3 Mt/a (3.3 million stpy) of ore from FIM. To achieve this goal, the company needs to optimize its processing, to maximize the amount of metal it extracts through FIM’s large flotation lead-zinc concentrator. To ensure high productivity, Peñoles and its contract engineering firm, M3 Engineering and Technology, of Tucson, AZ, have implemented anore processing system.

Jan 1, 2003

By K. M. Mohamed, R. K. Zipf

The shear strength properties of generic cement foam material and cement foam/concrete interfaces were examined at three testing scales. In laboratory direct shear tests on specimens with average shearing area of 0.006 m2 (10 in.2), the cement foam material had average peak and residual shear strengths of 0.88 MPa (128 psi) and 0.39 MPa (56 psi), respectively. Depending on the concrete strength, the cement foam/concrete interfaces had peak and residual shear strengths ranging from 0.71 to 0.81 MPa (103 to 117 psi) and from 0.27 to 0.29 MPa (39 to 42 psi), respectively. In laboratory direct double shear tests on specimens with average shearing area of 0.084 m2 (130 in.2), the cement foam/concrete interfaces had average peak and residual shear strengths of 0.17 to 0.30 MPa (25 to 44 psi) and of 0.11 to 0.23 MPa (16 to 33 psi), respectively. In large shear tests of simulated cement foam seals with the Mine Roof Simulator (MRS) test frame, cement foam/concrete interfaces with shearing area of 1.486 m2 (2,304 in.2) had average shear strengths of about 0.08 and 0.16 MPa (11 and 23 psi) along the roof and floor interfaces, respectively. The average shear strength through the cement foam material was 0.38 MPa (55.3 psi). Finite element analysis of the large seal tests and the back analysis of the shear strength of full-scale cement foam seals conducted at the NIOSH Lake Lynn Laboratory confirmed shear strength of about 0.14 MPa (20 psi) along the seal/rock interfaces. The study concluded that the structural analysis of cement foam seals should be based on their residual shear strength determined from small laboratoryscale tests of the cement foam/concrete or rock interface and not be based on their peak strength.

Jan 1, 2014

By B. Caro Vargas

The Toulon Tunnel project is a key component of the highway corridor on the French Riviera between Marseille and Nice and is a fundamental transportation infrastructure for the region. The first design studies started in the 1960s. The tunnel project is comprised of two separate tunnels: south and north. The north tunnel was built between 1992 and 2002 after 10 years of difficult construction. On March 15, 1996, for example, a collapse of the tunnel in the Marchand area generated a sinkhole in the city center, causing a 20-month delay. The south tunnel alignment runs parallel to the north tunnel below Toulon?s historical downtown at a depth of 20 to 40 m (65 to 131 ft) with some areas with less than 10 m (32 ft) of cover. The risk management program was studied to be a state of the art program in urban tunneling construction.

Jan 1, 2012

By D. Olsen, S. Cole, J. Strid, G. Colzani

This paper focuses on the underground tunnel work at the Hollywood Water Quality Improvement Project (HWQIP) in Los Angeles, CA. The HWQIP is being constructed to provide a water distribution system to bypass the existing Hollywood Reservoir System, which supplies drinking water for 500,000 people. The major project features include, a 2.9-meter diameter 1,829 meter long bypass tunnel, a 1.8-meterdiameter 366 meter long utility tunnel, 3 jack and bore tunnels, two 136 million liters underground circumferentially wrapped pre-stressed concrete water storage tanks, associated piping, and mechanical facilities. The physical project location coupled with strong community involvement and stringent environmental concerns was a considerable driving force for this project located in the Cahuenga Pass area of the Hollywood Hills north of Los Angeles, CA.

Jan 1, 2001

By Susan L. Bednarz

Recent advances in digital cameras and image processing allow photographers to produce excellent high-resolution action shots in low light and high contrast conditions commonly encountered underground. Digital photography is often used for construction and inspection documentation for underground structures. Designers, owners, and contractors benefit from quality photographs that document incremental progress and project milestones. Documentation photos serve as a lasting record of as-built conditions, are an important marketing tool, and help the owner build public support for expensive public works projects. When the project is complete, the only mementos that the participants will hold onto are the photographs.

Jan 1, 2008

By Jim Owens

The methodology of quarrying changed significantly in the Indiana limestone industry in the 60 years between Sept. 11, 1941 and Sept. 11, 2001. The former was the date of the Pentagon groundbreaking ceremony, while the latter was when the building was damaged by American Airlines Flight 77. So too, though to a lesser degree, did the machinery and methods used to fabricate the stone. The rededication ceremony on Sept. 11, 2002 marked the end of the Phoenix Project, as the rebuilding effort was named. The story of this remarkable project illustrates what the American construction(and Indiana limestone) industry can accomplish when working toward a common goal.

Jan 1, 2005

By J. Perlacia, J. M. Eguiluz

"INTRODUCTION The Bulk Handling Technology has suffered an important development in the recent years, allowing the use of conveyor belts in the most important and critical applications. As a consequence of this, the reliability and lasting performance of the conveyor belt components is becoming more and more significant, thus the implementation of preventive maintenance programs is a must. The rollers are one of the consumables in the conveyor belts, which have to be changed once arrived to the end of life. The actual ways of detecting this moment always require intensive use of labour and they are not very accurate. Indeed, if the rollers get broken before replacement, the consequences could be very important, generating additional costs and operational losses. The R&D Department of ULMA Conveyor Components, has been working since early 2012 on the development of Monitored Rollers along with a Management Software to provide users the capacity to Manage and Monitor the rollers from its desk, getting continuous online information on the internal temperature of the bearings, on the working status of the rollers as well as the identification of the rollers close to their end of life so that they could be changed during the next maintenance stop of the conveyor belt. In short, a system of Preventive Maintenance for Conveyor Belt Rollers BACKGROUND AND CURRENT STATE The malfunction of a single roller in certain conveyor belts can suppose the standstill of the whole installation until its replacement, due to the risk of greater and more expensive failures like the rip of the belt. In the case of a bulk handling installation where a continuous supply of material is necessary, a bare stop of one hour could entail huge economical losses. What’s more, many conveyor belts are several kilometers length or the access to some parts of them is very complicated. Due to these difficulties the inspection and maintenance operations can become expensive and hard going, with staff going over the whole area checking the correct condition of the conveyor and rollers, which means a dangerous activity. In addition, it’s quite common to find rollers working in very harsh conditions, completely exposed to the elements or working in corrosive closed environments like underground mines. These tough working conditions together with the very demanding features of Bulk Handling sector (high loads, speed, dangerous materials etc.) can bring the unexpected failure of a roller, even being designed to support them. Thus, to have the working conditions of the rollers real time is clearly required, in order to achieve an actual predictive maintenance of the system and avoid fatal failures. Nowadays the most common procedures to identify a broken roller is to hear how it sounds or use thermo-graphic cameras to measure their internal temperature, both of them implying workers inspecting the whole length of the conveyor while the conveyor is running. This means intense use of workmanship and operational safety level reduction."

Jan 1, 2018

By Roberto J. Guardia, Ted Lewtas, Peter Rasmussen, Klaus Winkler

As part of the Lake Fort Smith Water Supply Dam Enlargement project, located in northwest Arkansas, microtunneling methods were used to install two side-by-side,1.53m (60-in) inside-diameter steel pipes between the intake structure shaft and the lake. The 46.6 m- (153 ft-) and 41.7 m- (137 ft-) long tunnels were excavated in Pennsylvanian sedimentary bedrock ranging from coarse sandstone to siltstone and shale-like claystone. The intake tunnels were constructed 18.3 m (60 ft) below lake level from the dry shaft. Special installation methods and procedures described herein were used to complete the lake taps. Installation difficulties that caused minor delays are also reviewed. After the excavation of the Intake shaft was completed, the two lake taps were installed in approximately ten weeks with the same microtunneling machine.

Jan 1, 2005

By R. D. Sharpe

Gypsum wallboard manufacturers in the United States shipped 3.18 billion m2 (34.2 billion sq ft) of wall-board products during 2004 versus 2.93 billion m2 (31.5billion sq ft) in 2003. Following a historic high production of gypsum wallboard products in 1999, production decreased in 2000. But it has steadily increased during2001 through 2004. Wallboard production in the United States increased about 8.6 percent in 2004 from 2003. Following several years of a “building boom” of new wallboard plants and the expansion of the manufacturing capacity of several existing plants, 2004 was a relatively quiet year. However, several new plants and capacity expansions were announced or are in progress during 2004.

Jan 1, 2005

By Jamal Rostami, Richard Kastner, Ahmad Ramezanzadeh

Improving the accuracy of the performance prediction models for hard rock Tunnel Boring Machines (TBMs) is important in estimation of the schedule and cost of tunnelling in related projects. The effects of rock mass on performance of TBMs has been studied extensively, yet due to the complex nature of the process, impact of many parameters influencing machine advance rate are not very clear and there is still room for improvements. More accurate estimates can be obtained by better understanding of operating parameters in various geological conditions and can lead to matching machine specifications with job conditions, optimizing machine performance, and avoiding long delays and downtime for increased productivity. This paper will offer review of two case histories including Queens Water tunnel in New York and KCRC project in Hong Kong. The analysis of the available field data, including the geological back mapping and results of laboratory testing of rock mechanical properties, machine operational parameters and achieved rate of penetration will be presented. This includes statistical analysis of available field data to provide a better understanding of the influence of rock mass properties on performance of hard rock TBMs as well as related formulas to improve performance estimates.

Jan 1, 2005

By Yunxing Cao, Xinsheng Zhang, Bingbing Meng, Shuaifang Guo, Li Wang, Junsheng Zhang

During the initial process of mining a longwall working face, it is often found that the roof will not collapse readily, which increases the risk of later roof collapse disasters. Explosive and hydraulic fracturing are common roof weakening techniques; however, they have certain limitations. In the present study, CO2 fracturing was used for roof weakening during the initial mining phase in the Changcun coal mine, China, which is a novel strategy. First, by analyzing the lithological characteristics of the working face and applying combined beam theory, the breaking spans of the top coal, immediate roof, and main roof were determined before weakening. An F-35 CO2 fracturing device with a rated pressure of 270 MPa was used, which provides fracturing energy equivalent to 0.968 kg of TNT. The fracture radius of the main roof was studied by ANSYS/ LS-DYNA combined with the hanging roof-breaking theory to determine the optimal layout of CO2 fracturing drills. The results show that the breaking spans of the top coal, immediate roof, and main roof were reduced by 3.99 m, 7.66 m, and 22.03 m, respectively. The main roof collapsed as the working face advanced, eliminating the chance of later roof collapse disasters. Compared with hydraulic fracturing and explosives, CO2 fracturing is safer and more practical, giving it significant application potential.

Nov 23, 2023

By G. Duncan, K. Winther, R. Ericsson

Distinct trends in grinding mill technology have emerged in recent years. In an effort to optimize overall mill performance for the needs of the End User, broad measures of logistical speed, process flexibility, operational risk, and overall costs now exert greater influence on the specification of grinding equipment. As a result, innovative alternatives to conventional grinding mill structures, supports, drives, feed, and discharge configurations are now being offered and selected with greater frequency. This paper investigates these trends in grinding mill technology, utilizing optimization and decision-theory techniques. In particular, the paper considers how specific advances in process design, product engineering, manufacturing techniques, and mining operations continue to relax technological constraints, enabling further mill innovation. In this context, a methodology is presented, illustrating how proper selection and specification of grinding mill components and configuration can target an optimization of the four End-User performance measures listed above.

Jan 1, 1999

By M. Karmis, C. Haycocks

The evolution of longwall mining is briefly traced from its inception in England in the 1620's. In the beginning this method recovered 90% of coal with roof closure controlled by packs and walls. Mechanization began with kerf cutting, crude face conveyors, and improved face support. Full face mining was accompanied by the introduction of self- advancing hydraulic supports. U. S. longwalls evolved a retreating system to recover blocks of coal outlined by room and pillar panels. Computer control combined with the most modern technology have greatly increased productivity. Past trends are used to predict future technological directions.

Feb 24, 1997

By Konstantinos Komnitsas, Evangelos Petrakis, Emmanouil Varouchakis

During the modeling of grinding systems, population balance modeling (PBM) which considers a constant breakage rate has been widely used over the past years. However, in some cases, PBM exhibited some limitations, and time-dependent approaches have been developed. Recently, a non-linear framework which considers the traditional linear theory of the PBM as a partial case was introduced, thus allowing the estimation of product particle size distribution in relation to grinding time or the specific energy input to the mill. In the proposed model the simplified form of the fundamental batch grinding equation was transformed into the well-known Rosin–Rammler (RR) distribution. Besides, the adaptability and reliability of the prediction model are among others dependent upon the operating conditions of the mill and the adjustment of the RR distribution to the experimental data. In this study, a series of grinding tests were performed using marble as test material, and the adaptability of the non-linear model was investigated using three loads of single size media, i.e., 40, 25.4, and 12.7 mm. The results indicate that the proposed model enables a more accurate analysis of grinding, compared to PBM, for different operating conditions.

Jun 24, 2023

By H. A. Taylor

Graphite is elemental carbon that crystallizes in the hexagonal system as six-sided platelets. It occurs naturally and is mined. And it can be made artificially from petroleum coke in the form of shapes (electrodes) and powders. The market for most kinds of graphite in most end-uses was good in 2004. The 2005 graphite market looks positive. The major graphite prices, as given in Industrial Minerals, remained unchanged throughout the year. The preliminary 2004 U.S. Geological Survey (USGS) prices for natural graphite showed almost no change for crystalline flake. They were $600/t ($544/st) in 2004 and$622/t ($564/st) in 2003. Mexican amorphous graphite was almost unchanged at $150/t ($136/st) in 2004 from$152/t ($138/st) in 2003.

Jan 1, 2005

By F. Habashi

The changes that took place in China between 1984 and 2004 are remarkable. Visits were made to universities, research institutes, metallurgical industry, and many cultural centers within five trips during this twenty years period. The impressions of these visits are outlined.

Jan 1, 2007

By B. P. Faulkner, M. Weinecke

Svedala started a development program in 1997 to develop a process to convert waste tires into valuable commodities. A review of numerous approaches revealed short-comings in the various approaches either process, mechanical, combination of factors, or trying to emphasis the production of low value products. A market study revealed that a process that could produce a good grade of carbon black would be economically feasible. This paper discusses the laboratory and pilot plant development and commercial plant design.

Jan 1, 2001

By J. Swanepoel, J. H. van Laar, J. C. Vosloo, W. A. Pelser

Deep-level underground mining costs in South Africa are continuously rising due to the increased depth at which gold is being mined, resulting in a rise in virgin rock temperature and an increase in cooling requirements. Therefore, mines must evaluate various ventilation and cooling optimisation projects required to be implemented throughout their life of mine (LOM). This study develops a method to identify and prioritise large capital expenditure (CAPEX) underground environmental improvement projects, to improve thermal comfort underground. The solution presents a ‘multi-criteria decision-making’ (MCDM) process, incorporating the ‘analytic hierarchy process’ (AHP) and the ‘technique for order performance by similarity to ideal solution’ (TOPSIS) into the method to provide for scientific decision-making. These projects are evaluated based on four criteria, namely project risk, the impact on the underground thermal comfort, cost, and implementation time. This study’s solution uses ventilation simulations to determine the impact of the projects on the underground environment. The identification and evaluation of an environmental improvement project to best suit the current economic climate, while improving underground conditions and decreasing the safety risk is an essential aspect of the solution developed in this study. The method was implemented on a mechanised deep-level underground mine and showed that surface refrigeration is the most suitable alternative, which was implemented at the case study mine as validation of the developed solution. The study proves that the MCDM method is an adequate solution to incorporate subjective criteria into the decision-making process, resulting in a scientific and structured approach to making significant and complex decisions.

Feb 17, 2023