Search Documents

By Jerry T. Shelby

Surface and underground mining operations require equipment with high power output ratings. Haul trucks, loaders, dozers, and other equipment need increasing horse-power to meet production demands. To get more horsepower out of the engines driving the equipment, most manufacturers use turbocharging. Detroit Diesel puts the number at about 90% turbocharged, while Caterpillar estimates 75% to 80% of all its equipment is turbocharged. Turbocharging increases the power output and overall engine efficiency. But it presents some maintenance and operational problems that were not factors when only naturally aspirated engines (nonturbocharged) dominated the scene. A turbocharger is an exhaust-driven air compressor. Using the waste energy in the engine exhaust, a turbine wheel is driven. This wheel is connected by a common shaft to a compressor wheel. The shaft is supported by two plain bearings, or bushings. As the turbine wheel is rotated, the compressor wheel continually compresses the intake air to the cylinders. Compressing the intake air means that more air can be put into the cylinder to burn more fuel. The more fuel the engine can completely burn or combust, the more horsepower the engine can produce. Even though the turbocharger is a relatively simple device, it is a sensitive engine component. It requires special consideration at engine start-up and shutdown. Being freewheeling and exhaust driven, turbochargers can experience temperatures of 540°C 1000°F) and rotational speeds of more than 100,000 rpm. Due to those temperatures and speeds, lubrication is critical to the operation and life of a turbocharger. The turbo is located high on the engine, with the oil supply running through an external line from the sump. The recommended practice is to start the engine and allow it to idle for a few minutes before any revving or loading. This allows the oil to reach the turbo and properly lubricate the bearings before high rotational speeds are seen. Turbo oil supply lines can be as long as 1.5 m (5 ft). Depending on ambient temperatures and oil viscosity, it can take as long as 30 seconds for oil to reach the spinning turbo. However, as little as five seconds without oil can damage the turbo's bearings, reducing its life and overall efficiency. Lubrication problems seen at shut-down can also significantly affect turbo life and efficiency. Manufacturers recommend an idling period of five to seven minutes before engine shutdown. This allows the turbo to slow down and cool off somewhat to help prevent oil coking and bearing damage. When the engine stops, so does the oil supply. There is very little oil left on the bearing surfaces and in the turbo oil supply passages. The immediate heat transfer from the turbine wheel to shaft, bearings, and turbo body literally cooks what is left. This high heat without oil flow can cause bearing deformation by actually melting some of the bearing material. The rapid oil oxidation and coking will restrict oil passages, damage bearings and shaft. Besides heat soaking, there is another problem. If the turbo is spinning at high speeds when the engine is shutdown, the turbo must spin-down to a stop without oil flow. With the large size of turbos used on mining equipment, this spindown time without oil can be for as long as 10 to 20 seconds. Fortunately, lack of lubrication at start-up and shutdown and the subsequent bearing damage can be prevented by oil injection devices. These devices hold a reservoir of engine oil. The oil is injected to the turbocharger bearings immediately on start-up and for several minutes after shutdown. Oil injection devices are spring loaded, hydraulic accumulators. They are actuated at start-up by a solenoid wired to the starter motor. Engine oil pressure charges the accumulator during normal operation. Upon shut-down and loss of oil pressure, the device provides oil to the turbo for about two or three minutes. With an oil injection device, the engine can be started and immediately driven without fear of turbo damage. Also, an abrupt shutdown will not damage the turbocharger since the device will continue to lubricate for two or three minutes. A word of caution. Be sure the oil injection device provides positive oil displacement (pressurized oil flow). Do not use a gravity-flow device. Unless it is a true accumulator, the device could starve the turbo for oil on start-up, Ask for start-up and shut-down pressures and delivery times before considering installation. Keep the oil clean, and follow the manufacturer's recommended oil change intervals. These intervals are usually shorter than with naturally aspirated engines. Use oil with a CD rating designed for diesel applications. A multiviscosity oil is preferable. Use a synthetic engine oil, such as Mobil's Delvac 1, Gulf's Super Duty II, or Chevron's Sub-zero Fluid. Synthetics have much better flow properties at low temperatures. They also have greater oxidation stability (they can take the high heat of turbo-bearing lubrication. And they produce fewer deposits because they are more thermally stable. But synthetic oils do cost more - two or three times more. One additional point - maintain the air intake system. Since all mining is usually in a dusty environment, air filters should be changed regularly and intake systems should be checked for leaks. All intake air passes through the turbo. Any dirt or abrasives entering the turbo will damage the unit and shorten its life. While mining is a heavy duty business with severe operating conditions, you can get the life from your turbocharger that you expect by following a few simple steps: • equip the turbo with an oil-injection device to provide lubrication on start-up and shutdown; • change the oil and filters regularly; and • use the proper oil-synthetic, if possible.

Jan 3, 1987

By F. B. Kuhnow

When performing blasting operations in open pit settings, energy is released and transmitted through the geology. Some negative effects can have significant impacts on mining operations and adversely affect mine production. This technical paper presents recommendations for blast design to prevent damage due to ground motion from blasting on adjacent concrete structures of underground operations. The paper includes a case study describing a problem regarding an open pit mine expansion and asks whether production blasting will damage concrete shaft structures due to blast stress waves and blastinduced ground motion. Based on the results, a set of criteria is provided to implement in current and future mining operations that involve blasting near underground concrete structures. A set of techniques on how to improve vibration levels for safe operations is also presented. Knowledge of particle velocity and wave propagation for site-specific circumstances to determine a safe level of vibration is recommended. Emphasis is placed on making use of electronic detonators and early delay detonators to achieve successful levels of vibration. A dynamic analysis is necessary to determine if vibration from blasting can damage the concrete shaft structure. When reinforced concrete structures are subject to blast loading, both concrete and steel are subject to very high strain rates. As opposed to static loads, when subject to high strain rate loads these materials increase their strength significantly. In fact, they increase by more than 50% for reinforcing steel, by more than 100% for concrete in compression, and by more than 600% for concrete in tension. This finding is of significant importance in mining operations because it allows an increase in flexural capacity of individual members as a result of high strain rates. Therefore, an elevated ground vibration (PPV) or particle velocity is permissible when blasting takes place near concrete structures.

Jan 1, 2014

By Corby G. Anderson

Since 1985, the Sunshine Mining Company has used a patented nitric-sulfuric acid pressure leaching system for production of silver and copper from a refractory sulfide ore body. To better understand this novel process, a program of lab scale testing was undertaken to quantify the effect of system variables on silver recovery. Some of the factors studied include temperature, agitation, acidity, vessel pressure, particle size, percent solids and oxidizer amount. In turn, this knowledge will be applied in actual plant practice to upgrade reaction time, increase concentrate throughput, raise silver recovery and lower reagent costs. A discussion of plant process changes resulting from lab scale testing is included.

Jan 1, 1991

By R. J. Robbins

The mechanization of hard rock underground mines offers a large potential for reducing cost, improving efficiency, and increasing profitability. However, in spite of serious efforts by quite a number of equipment developers and mining company initiatives, the industry has achieved little real progress. The task is difficult and the blasting alternative to mechanical excavation is an effective and well-developed method, which continues to improve in spite of its inherent limitations. A large number of machines have been built and tried. Only a few developments have succeeded to make a major impact on underground hard rock mining. It is certain that hard rock mines would be laid out and designed quite differently if the mining engineers knew they had available continuous mechanical excavation machines. In the absence of the machines, mines will be designed for excavation by traditional methods. It is not easy to utilize mechanical excavation in a mine which is designed to operate with normal drill and blast excavation. This is certainly an impediment to machine development. But what if an ore body cannot be mined conventionally, simply because the mining company cannot get permits to satisfy the ever increasing strict EIS requirements of the general public and governmental agencies? This may provide the incentive necessary to develop the equipment that will be needed by a new mining method that will have almost no impact on the environment.

Jan 1, 2001

By J. A. Botín

Traditional risk quantification methods provide little information on the sources of risk, and tend to produce static over-conservative evaluations, which do not account for changes in the performance of the project. Capital investment decisions for large mining projects require of more complex risk evaluation models, that include the value of flexibility and the different risk levels associated with uncertainty on project variables (price, grade, dilution, production rates, among many other). In this context, Real Option Valuation (ROV) methods have proven potential to quantify the risk associated with such variables and integrate alternative scenarios and management strategies into the evaluation process. In this paper, a risk quantification model is developed, which successfully quantifies the risk associated to dilution, as a function of production rate. This model is then validated in a case study on the Chuquicamata Underground Mining Project.

Feb 27, 2013

By Shimi Tzobery, Jay Davenport, Raymond Henn, Sam Bandimere

Over the past several decades, the use of cement-based grouts using ultra fine cement as a replacement for portland cement has begun to gain acceptance as an alternative to chemical solution grouts used in permeation grouting. The amount of information currently available on grouts made with ultrafine cement is limited. The authors used a previously developed field testing program to perform additional tests to evaluate the permeation performance of portland and ultrafine cement-based grouts. For the first time, the 2003 testing program included an attempt to determine the 28 day compressive strength of the sand permeated by the grout.

Jan 1, 2005

By H. Colijn

Belt conveyors have proven themselves for many years as a dependable and low cost method of handling bulk materials at high flow rates. The success of a belt conveyor system greatly depends on the initial loading of the material on the belt. If the material is loaded on the belt at the center, at approximately the same speed and with minimum impact, then most of all belt conveyor problems disappear. Proper belt loading is primarily determined by the engineering and design of the conveyor transfer point. This paper will establish and discuss some general design criteria required for proper loading and transfer of materials from one conveyor to another. Specific attention is given to loading points, chutes, skirt board length and general design of transfer structures.

Jan 1, 1971

By R. L. Virta

Six companies mined fire clay in Missouri and Ohio during 2004. Production, based on a preliminary survey of the fire clay industry, was estimated to be 398 kt(438,700 st), valued at $9.81 million. This was slightly less than the production and value figures from 2003. Missouri was the leading producer state. It accounted for more than 70 percent of the U.S. production. Consumption Domestic producers sold or used fire clay primarily for refractory applications. This application accounted for 79 percent of the market. Refractory products made using fire clay include firebrick and block, grogs, high-alumina brick and specialties, refractory mortars and mixes, and saggers.

Jan 1, 2005

By D. Parks, A. Miller, M. McNinch, R. Jacksha

Each year, hundreds of mine workers are involved in machinery-related accidents. Many of these accidents involve inadequate or improper use of lockout/tagout (LOTO) procedures. To mitigate the occurrence of these accidents, new safety methods are needed to monitor access to hazardous areas around operating machinery, improve documentation/monitoring of maintenance that requires shutdown of the machinery, and prevent unexpected startup or movement during machine maintenance activities. The National Institute for Occupational Safety and Health (NIOSH) is currently researching the application of Internet of Things (IoT) technologies to provide intelligent machine monitoring as part of a comprehensive LOTO program. This paper introduces NIOSH’s two phase implementation of an IoT-based intelligent machine monitoring system. Phase one is the installation of a proof-of-concept system at a concrete batch plant, while phase two involves scaling up the system to include additional sensors, more detailed safety/performance metrics, proximity detection, and predictive failure analysis.

By David Kwietnewski

Roadheaders are gaining widespread acceptance in North America as a means for mechanical tunnel excavation. Until recently, almost all of the large-scale North American tunnel projects were excavated one of two ways ? the tried and true drill-and-blast method or with the use of tunnel boring machines (TBM), the hi-tech super-excavators. TBMs enjoyed fast-growing popularity worldwide as TBM manufacturers offered greater technology to meet the demand of the civil tunnel industry in the late 20th century. Recently, though, more tunnel projects, large and small, can thank the brute force of a roadheader for getting the job done.

Jan 1, 2011

By Christopher J. Vise

Although production operations at mines, representing the extraction and removal of the mined material, often appear to receive the greatest amount of attention, the emphasis given to auxiliary operations is continually increasing. This is due to the changing economic, social, and environmental climate in which modern mines must operate. Auxiliary operations can best be described as those activities that are not directly related to the extraction and removal of the mined material, but must receive proper attention if recovery is to take place in a safe, efficient, and socially responsible manner. In fact, certain mining auxiliary operations, such as strata control and ventilation, are considered to be of such importance that they warrant separate sections in this Handbook. Judging from a mine-personnel standpoint, it is not uncommon for a mine to hire the same number or more individuals responsible for auxiliary operations as the number assigned to production.

Jan 1, 2008

This paper presents a virtual prototype for the stress analysis of cable shovel components based on combination of flexible and rigid body approach. The general mechanical system of the cable shovel is modeled as a multi-body system with rigid and flexible bodies. The relevant theories applied for the dynamic model are described in terms of Lagrangian multi-body dynamics and finite element method. A virtual prototype of the cable shovel is built in the Automatic Dynamic Analysis Mechanical System (ADAMS) environment, which allows visualizing the motion of general mechanical system and analyzing the dynamic stress of structural components of the cable shovel. An example is given to perform dynamic stress of durability analysis for the boom and handle. Attention of this study is devoted to the mechanisms of damage of the cable shovel and also the critical high stress areas. Keywords: Cable shovel, Von Mises stress, Virtual prototype simulation, Stress virtualization.

Jan 1, 2009

By R. E. Vivas, J. A. Villa

"Located in the state of Colima, Peña Colorada is one of the largest iron ore operations in Mexico. The project is owned in equal parts by ArcelorMittal and Ternium. Though boasting a production capacity of 4.1 Mt/a (4.5 million stpy) of concentrate per year, Peña Colorada is faced with declining ore grades. In order to respond to this situation, Peña Colorada had to expand production even further. This expansion created various challenges that were overcome by the adoption and application of new technology. Examples of these technological innovations are discussed in detail in this article and include improvements in geo-modeling, mine planning, and mine operations. The successful implementation of these technologies paid for itself many times over, and has led to significant improvements in production and performance, while lowering the operating costs and reducing the variance between planning and execution.Project overviewPeña Colorada is a mining company that produces about 30 percent of the iron ore in Mexico. This project generates about 1,200 direct jobs and 3,000 indirect jobs, making a significant contribution to the local economy. Similarly, Peña Colorada invests in its local communities through numerous educational programs, scholarships, university agreements, social development, environmental agreements, etc. Peña Colorada’s operations consist of an open pit mine located in Minatitlán and a pellet plant located in the port city of Manzanillo, as shown in Fig. 1. Technological innovationsMost mining projects around the world typically follow the logic of “mining the next best ore.” Consequently, head grades tend to decline over the life of the mine. In the case of Peña Colorada, a decline in head grade combined with a decline in iron ore prices forced the operation to adapt to a new business environment and adopt new technologies to face these challenges. However, the first step along this process was to increase the confidence and reliability of the resource model. This task involved additional drillhole campaigns coupled with more detailed modeling techniques. Once the block model was completed, new optimization studies and production schedules were evaluated with new optimization tools that improved many aspects of the mine plan. The Peña Colorada block model has undergone 3 expansions to reflect additional information not available in the past. The model has expanded to the East and Southwest. The latest model expansion increased the total number of benches to 98 as a result of positive exploration results. Similarly, new geotechnical studies were prepared, which provided new guidelines for pit slope design, and new technology was implemented to monitor ground movement and slope stability. Two sectional block model views in Hexagon Mining’s MineSight 3D, along with the pit designs and geologic solids are shown in Fig. 2."

Feb 1, 2017

By Norbert T. Rogers

An accepted statement of fact is that, next to agriculture, transportation is the second most important industry in the world. The transportation networks of the United States have greatly contributed to our nation's growth and prosperity. The objective here is to make the reader aware of the need for communication between geologists, mining engineers, purchasing agents, and transportation managers. Only through a cooperative effort is it possible to reap the benefits of transportation in the industrial minerals field. Transportation is often thought of in terms of trucks, rail cars, barges, and covered wagons. There is much more. Corning Inc. Corning Glass Works is a worldwide organization with more than $2 billion in annual sales. It supplies more than 60,000 different products a year to some 47,000 customer firms and millions of individual consumers. Corning operates 32 of its own plants worldwide and is also an investor with a 50-50 or minority position in 24 affiliated companies in 11 countries. Corning competes in four broad business categories: • specialty glass and ceramics; • consumer housewares; • laboratory sciences; and • telecommunications Binding these four sectors together is the glue of technology. Coming's research laboratory, established in 1908, was one of the first in American industry. That early commitment to research has never wavered. Today, Corning spends annually on research and devel¬opment, as a percentage of sales, at double the average rate for all manufacturing industry in the US. Some 1500 scientists, engineers, and support personnel are now employed at the company's research and development centers in the US, Japan, and France. Petalite background A family of materials melted conventionally as a glass, then converted by special processing to a ceramic was invented in 1957. One of the basic minerals in this glass ceramic product is petalite. Petalite is a monoclinic mineral with a framework silicate structure and a low iron content, about 0.06% Fe2O3. Petalite is found in very few places throughout the world and no commercial petalite deposit has been found in the United States. Sizable deposits occur in Zimbabwe, Southwest Africa, Brazil, Australia, the Soviet Union, and Sweden. Coming's purchasing and geology departments located a source of petalite with proven reserves in what was then known as Rhodesia. The supplier was Bikita Minerals. The relationship with Bikita was one in which Bikita supplied bulk ore that Corning processed into a finished material at its US facility. This bulk ore method of shipment resulted in high losses through contamination and processing. It also caused tank upsets at the Corning plant because of iron contamination picked up through the numerous handlings of this product in bulk. The relationship with Bikita continued until 1965 when the white political leadership of Rhodesia declared its independence from Great Britain. This led to the imposition of international sanctions. The sanctions were lifted in 1980 and the relationship with Bikita was reestablished in 1983.

Jan 1, 1989

By Christopher J. Bise

INTRODUCTION Before a mine is planned in detail, a preliminary analysis is often conducted. This preplanning permits the mining engineer to make a rapid assessment as to whether or not a particular mining property warrants further consideration. In fact, a properly conducted preplanning phase can come within 10% to 20% of the actual results, thereby saving the mining engineer valuable time before committing himself to a fine-tuned analysis. The questions to be answered by mine preplanning are (1) What will be the operating conditions for the mine? and (2) How long will it take to complete the project? To answer these questions, calculations dealing with reserve estimation, production planning, man- power planning, and project scheduling are conducted. The following sections discuss these various phases of mine preplanning in greater detail. RESERVE ESTIMATION The estimation of the various characteristics of a reserve, such as quantity, grade, and thickness, is an ongoing process throughout the life of a mining venture. However, the reserve-estimation phase of mine planning is more closely associated with the preplanning phase. There are many different techniques employed in reserve estimation of solid mineral deposits; variations among them are introduced because of such considerations as ease of application or level of accuracy. In any event, each technique is developed in the following manner: (1) the mineral body is represented pictorially and then subdivided into blocks related to one or more samples of exploration data, (2) the area and volume of each block is determined, (3) the volumes are converted to representative tonnages (or, for example, grades), and (4) the results are tabulated. To illustrate this procedure, the polygonal (area-of- influence) technique will be presented due to its ease of application, flexibility in dealing with different deposits, and general acceptance. The polygonal method assumes that all characteristics of a mineral body extend halfway between a point of observation and any other point of observation. The explored portion of the mineral body is represented by polygonal prisms whose depths relate to the characteristic in question (grade, thickness, etc.) and whose plane bases relate to the area of influence of each point of observation (drill hole, etc.) as shown in Fig. 1. The polygons must be constructed in a definite order, usually clockwise and from the periphery to the center of the deposit. Table 1 can then be used to calculate the characteristics in question. Since, by definition, the polygonal method assumes that the characteristics of a mineral body extend half- way between points of observation, it becomes readily apparent that the evaluation of a vertical-drill hole exploration program requires that the sides of the polygons be formed by the intersection of perpendicular bisectors (Fig. 2). Figs. 3 and 4 show correct and incorrect construction of the polygons. The criterion for correct construction of the polygons is that all points within a particular polygon must be closer to its rallying point than those located in any other polygon. This is clearly not the case for certain points that are located in the polygon containing rallying point B in Fig. 4. Although this method can be used where the drill holes are irregularly spaced, calculations become less tedious when a square net (Fig. 5) or a chessboard (Fig. 6) grid is adopted. The numbers shown in Figs. 5 and 6 represent the relative weight for each of the shaded areas. In general, the greater the number of polygons, the more continuous the mineral body, and the more regular the grid, then the more accurate the computations will be. PRODUCTION PLANNING Before an acceptable evaluation of the production potential of a mine can be determined, a thorough exploration program should be conducted. It seems obvious that the nature and properties of the deposit and adjacent strata, the presence of impurities, and other mining conditions should be adequately determined prior to production planning and equipment selection. The lack of sufficiently detailed knowledge of the many mining parameters has led to the failure of numerous operations. For example, targeted production tonnages and equipment sizes for a coal mine are intimately related to the seam thickness. Needless to say the quality of information that is gathered from an exploration program can have a tremendous impact on the production plan. Production plans are developed initially by determining reasonable shift tonnages per operating section. Most of the time these values are developed from his-

Jan 1, 1986

By D. S. Yantek, C. B. Brown

The mining industry is beginning to implement lithiumion batteries (LIBs) to power mine utility vehicles (MUVs) and rubber-tired mantrips (RTMs). However, the ability of LIBs to withstand the harsh conditions for these applications has not been rigorously evaluated. Concerns with the use of LIBs in the mining environment will be discussed including the effects of mechanical shock and vibration, temperature extremes, and moisture exposure. This paper will discuss adverse effects of the mining environment on LIBs and provide an overview of scientific gaps associated with the environmental susceptibility of LIBs used on MUVs and RTMs.

Feb 1, 2024

By Henning Schwarz, Faisal Al Arifi, Anas Almousa

"The Riyadh Metro Project forms part of a complete new public transport system integrated in the urban planning and development of the fast growing capital city of the Kingdom of Saudi Arabia. The Design & Build project consists of 176 km of a new metro network with 57 km of double track single tunnel infrastructures, spread over six metro lines. During the design phase, geological, hydrogeological, geotechnical and geophysical site investigations were undertaken to chart the, previously uncharted, underground construction space. Different TBM solutions were selected for implementation taking due consideration of the ground conditions of each metro line. The results obtained from deep excavations for underground stations and analysis of the TBM tunneling data will be used as key input for future tunneling projects in the Riyadh and the Kingdom of Saudi Arabia. The present paper details the design conditions and presents the solutions for large diameter tunnels in karstic limestone. INTRODUCTION The High Commission for the Development of Arriyadh was established in 1974 as the organizational, planning, executive and coordinating body responsible for the development of Riyadh. Arriyadh Development Authority (ADA), established in 1983, is the High Commission’s executive, technical and administrative arm. The ADA is responsible for implementing the High Commission's organizational, planning, executive and coordinating decisions and missions (ADA 2015). One of the remits of the ADA is the preparation and execution of a transport plan for the city. The metro network is planned to be the backbone of the public transport system developed as part of the King Abdulaziz Project for Riyadh Public Transport in Riyadh. With six lines and a total length of 176.5 km (Table 1) and 85 metro stations, the metro network will cover most of the densely populated areas, public facilities, and the educational, commercial and medical institutions. The network will connect the King Khalid International Airport, the King Abdullah Financial District, main universities, Riyadh downtown and the public transport center. The public transport plan includes a future bus network with 22 lines on 1200 km and 6765 stops that will be the main feeder for the Riyadh metro network; it will also be the main mode of transportation within and around Riyadh districts (ADA 2015)."

Jan 1, 2016

By B. Radwanek-Bak

The assurance of future raw materials supply to the EU mineral industry has become, in recent years, one of the most important tasks of the EU Commission. It is focused on creation a new mineral policy within the EU zone. One of the starting points for this activity was identification of the mineral commodities that are critical for the sustainable development and technological progress. The paper presents the glance to this problem from the National Member level. Domestic mineral reserve base as a possible source of critical raw materials for the EU was shown. Poland cannot be considered as its resource base. The source of these raw materials are not only scarce in Poland, but also they are not produced, and their demand is now - and according to forecasts is going to be in the future - met by imports. The raw materials in question are not considered exactly critical for Polish economy, but they are of limited economic importance. On the other hand, their growth is a best opportunity and at once the need to the future sustainable development.

Jan 1, 2011

By J. Wiese

Recently the operating philosophy at concentrators processing platinum bearing ores has started to move from a recovery dominated system to one in which the production of high grade concentrates at the expense of some recovery would provide greater benefits in the further upgrading of the platinum group minerals (PGM). The low grades usually obtained are associated with the presence of naturally floatable talcaceous gangue minerals in all PGM ores. Polysaccharide depressants such as guar gum and carboxymethyl cellulose (CMC) are used to improve the grades of the concentrates. Recent testwork has shown that the use of high depressant concentrations can prevent any naturally floatable gangue from reporting to the concentrate. The only gangue present in the concentrates would be due to its entrainment in the froth. Under these conditions much higher grades can be achieved. The sulphide minerals themselves, however, become susceptible to depression at high depressant concentrations. This work examines how the recovery of sulphide minerals in two Merensky ores was affected by the type and concentration of the collector in the presence of high depressant concentration (500 g/t) and that the response of the sulphide minerals was also dependent on the type of depressant used (guar or CMC).

Jan 1, 2009

By Leslie F. Ruppert

The US Geological Survey (USGS) is currently conducting a coal resource assessment of the coalbeds and zones that are projected to provide the bulk of the nation’s resources for the next few decades. The Pittsburgh and Upper Freeport coals are the first two beds in the northern and central Appalachian basin region to undergo fully digital coal assessments. The bed-specific assessments are being carried out in partnership with the state geologic surveys of West Virginia, Ohio, Pennsylvania and Maryland. Comprehensive stratigraphic and geochemical databases have been developed for both of the beds. The extent of the bed with mined areas, structure contour, isopach, and overburden thickness maps for the Pittsburgh coal bed have been released as USGS open-file reports.

Jan 1, 1999