Search Documents

By Jafar Safarian, Manish Kumar Kar, Ahmad Hassanzadeh, Casper van der Eijk

To minimize the carbon footprint in the industrial valourization of bauxite residue, hydrogen was used as a reducing agent. The current study experimentally investigated hydrogen reduction of bauxite residue-CaO sintered and self-hardened pellets at 1000 °C, along with magnetic separation of these reduced pellets for iron recovery. Calcium was introduced to bauxite residue to form leachable calcium aluminate phases with the existing alumina in bauxite residue. This involved the addition of either CaCO3 or a mixture of CaO and CaCO3 while maintaining the fixed Ca content during pelletization. The former underwent sintering at 1150 °C, while the latter was self-hardened through the cementing effect of CaO in exposure to moisture and air. Both types of pellets were reduced in a thermogravimetry furnace at an elevated temperature under similar conditions. The pellets were characterized by the X-ray diffraction (XRD) method and scanning electron microscope (SEM) coupled with energy dispersive spectroscopy (EDS), and their physical and mechanical properties were measured via standard techniques. During hydrogen reduction, a negligible amount of gehlenite ( Ca2Al2SiO7) was formed in the self-hardened pellets, while this phase dominated in the sintered pellets. Alumina in the bauxite residue converted to mayenite phases during reduction in both the pellet types; however, reduced self-hardened pellets had a higher amount of alumina containing mayenite leachable phase. The two pellets showed similar reduction behaviour, while different chemical, physical, and mechanical properties were observed. The magnetic properties of milled reduced pellets were examined through a Davis Tube magnetic separator in a wet environment under a constant magnetic field of 800 G. Higher iron recovery was observed for the self-hardened reduced (41%) pellets than for the sintered pellets (27%).

Nov 23, 2023

By C. D. Elifrits

The required reclamation of land disturbed by surface coal mining often results in the creation of some over steepened slopes which are prone to rapid erosion and sediment production. This natural activity on such slopes is not desirable nor allowed under current regulations. Experience has indicated that novel approaches must be devised to address the problem. Research conducted on field sites in Missouri has indicated that construction, during the reclamation and grading processes, of a man-made drainage system will control the erosion. The drainage system must replicate or exceed the natural system in terms of drainage density and channel frequency. Basic design considerations will be summarized in this paper and field results shown.

Jan 1, 1986

By Marshall D. Himes

The Pima mine, 39,000 ton per day copper mine, is located 17 miles south of Tucson, Arizona. The mine is in a sequence of Paelozoic and Mesozoic sediments striking east-northeast and dipping southeasterly intruded by a Tertiary quartz monzonite porphyry. The Paleozoic Permian(?) dolo¬mites, limestones, and sandstones have been altered to talc-silicate skarn, marble and quartzite. The overlying Mesozoic Triassic(?) clastic sediments have undergone some recrystallization and hydro¬thermal alteration. The clastic metasediments are divided into three distinct lithologic units, lithic arenite, arkose, and inter¬bedded and overlying black argillite. Three types of hydrothermal alteration in the clastic rocks are propylitic alteration (epidote, chlorite and quartz, with or without sericite), quartz-sericite alteration, and potassic alteration (K-feldspar and quartz, with or without sericite and chlorite). The porphyry has undergone potassic alteration. Dominant structures are an east-west post mineral fault in the western part of the pit, and strong low angle faulting and shearing which truncates the ore body at depth. Two joint sets, one parallel to bedding and the other at right angles to bedding are prominent in the mine. Faulting is in two dominant directions, one striking northwest, dipping northeast and the other striking northeast, dipping northwest. Mineralization is predominantly disseminated pyrite and chalcopyrite, and molybdenite-quartz veinlets. There are lens important amounts of magnetite, hematite, sphalerite, galena, tennantite and bornite. Mineralization is believed to be both structurally and chemically controlled.

Jan 1, 1972

By Lane White

In mid-April 1992, MINING ENGINEERING mailed a survey questionnaire relating to mining shovels and hydraulic excavators to 125 SME members working at surface mines or at the headquarters of companies that operate surface mines. The mailing was directed to individuals whose titles indicate that they have management or mine planning responsibilities for surface mining operations. A total of 56 usable surveys returned by June 17 are the basis of this report. Precious metals mines Eighteen precious metals mines or mining companies returned completed surveys in time to be included in this report. Of these, 14 use hydraulic shovels only for both ore and waste, I uses both hydraulic and rope shovels, and 2 use Caterpillar 988 front-end loaders for both ore and waste. (Of the latter 2, neither expects to be in the market for a shovel in the next three years. I of these 2 placed Harnischfeger P&H number one and O&K number two in response to the question, "Based on your current knowledge of their machines, which manufacturer would you likely chose to supply new shovels or excavators to a mine or mines operating under your responsibility, if you were in the market?") Another uses front-end loaders, make not designated. The latter does not expect to be in the market for mining shovels or excavators within the next three years. Of the final total of 14 precious metals mines using only hydraulic excavators to load ore and waste, 8 use Hitachi excavators only, 1 uses Demag excavators only, 1 uses Liebherr excavators only, 1 uses O&K excavators only, 1 uses Harnischfeger P&H and O&K excavators, 1 uses Harnischfeger P&H and Hitachi excavators, and 1 uses Hitachi and Demag excavators. Of the 14 precious metals mines using only hydraulic excavators, 7 use excavators in the 7.6 to 11.5 m; (10 to 15 cu yd) size range. Of these 7, 5 use only excavators in this size range, and they are used to load both ore and waste. 1 of the 7 also uses 11.5 to 17 m' (15 to 22 cu yd) excavators, and I also uses a 17 to 23 m3 (22 to 30 cu yd) excavator. Of the 7 remaining of these 14 precious metals mines that use only hydraulic excavators, 3 use 11.5 to 17 m' (15 to 22 cu yd), 2 use 17 to 23 m3 (22 to 30 cu yd), and 2 use less than 7.6 m' (10 cu yd) units.

Jan 1, 1992

By H. R. Manouchehri

"Pyrrhotite (Po) is one of the most abundant sulfide minerals in processing industry and must be rejected in most cases. Particularly, Po rejection and its selectivity against pentlandite (Pn) have long been a challenge due to similarities in the mineral composition of the two minerals and the collectorless flotation characteristics of Po. Xanthates have been widely used to promote sulfide mineral flotation; however, in the presence of xanthates, the redox potential established at the mineral/solution interface is most important, determining the flotation performance. In this paper, the importance of electrochemistry in Po and Pn flotation has been demonstrated and a comprehensive study was conducted on two different feed streams (i.e., magnetic concentrate and scavenger cleaner streams, containing magnetic and nonmagnetic forms of Po, respectively), from Vale’s Clarabelle Mill in Sudbury, Ontario, with an objective to determine if improvements in Po rejection and Pn recovery could be achieved by controlling pulp electrochemistry. By conducting a series of flotation tests under different Eh conditions and reagent usage schemes, it was revealed that higher Po content in the magnetic stream may protect Pn from being oxidized, improving Pn recovery. The results indicated that at low oxidizing pulp chemistry, the rest potential for the Pn is still high enough to allow the formation of dixanthogen to promote its flotation. Using a Pt electrode, it was found that by controlling pulp potential at -50<Eh< +50 mV, the Pn recovery and Po depression would be satisfactory. The results, using mineral electrodes (Outotec Chena analyzer), indicated that selective separation can be achieved if low-to-moderate oxidation potentials (0 to 100 mV) or reduction (0 to -100 mV) potentials are monitored using Pn and Po electrodes. Mixing two streams at 50:50 wt % would be possibly beneficial in selective separation.IntroductionPyrrhotite (Po), Fe1-xS, is one of the most abundant sulfide minerals in the processing industry. It is an iron-deficient sulfide that occurs either in monoclinic or hexagonal form. The monoclinic one is richer in sulfur and is ferromagnetic, whereas the hexagonal Po is poorer in sulfur and has no magnetic properties. In general, the ferromagnetic properties of natural Po increase with increasing sulfur content. Although Po holds significant iron content, it is not used as a feedstock for the iron and steel industry due to the difficulty in achieving complete removal of sulfur. The common availability of iron oxide ores makes the iron sulfides irrelevant for the steel industry."

Jan 1, 2015

By Enrique Rubio Esquivel, Matías Fuentes Bustamante

The transition from open pit to underground mining represents a key strategic challenge in modern mine planning. This paper presents a multicriteria and multivariable methodology to plan such a transition, integrating technical, economic, environmental, and social considerations. The proposed framework focuses on risk reduction (de-risking) through the identification of alternative development paths, the use of stochastic simulation to model geological and technical uncertainty, and different mining strategies such as methods, production rates, sequence, etc. for ultimate underground implementation. The study summarizes the limitations of traditional planning methods—which usually treat the open pit and underground mine designs as independent processes—, also often it considers a single mining method and production rate for the underground option. Instead it is proposed an integrated approach that leverages synergies between both mining methods and scalable production rates. Also the proposed methodology incorporates the definition of critical variables (geotechnical, economic, and social, among others), the construction of multiple operational and technological transition paths, and the evaluation of each path under criteria of economic attractiveness and practical do-ability (capacity to be executed). Using simulation tools (SIMPLAN for operational performance and SIMVAL for economic evaluation), probabilistic distributions of the different path are obtained, enabling the quantification of the project’s Value at Risk (VaR). A subsequent multicriteria analysis weights the expected profitability against the feasibility of execution of each alternative, producing a decision matrix that provides a framework for evaluating the different project path. As a result, the proposed approach identifies OP→UG transition strategies that maximize business value by capturing remaining resources while minimizing financial and operational risks. Finally, strategic conclusions and recommendations for the industry are provided, emphasizing the importance of early transition planning even challenging the open pit sequencing of the latest push backs by introducing early underground operations. Future work includes strengthening the methodology—such as integrating real-time analysis and adaptive decision-making—and providing recommendations for its application in various mining operations. In summary, this paper delivers a technical and professional framework to guide mining companies on when and how to carry out a successful transition from open pit to underground mining, balancing resource recovery with financial, operational, and social security.

Feb 22, 2026

By Ernest Y. Baafi

The technique of linear kriging as a grade estimation method of mining blocks is reasonably established in the mining industry. Because of the nonbias condition imposed in kriging which requires that the kriging weights (?i) add up to one, negative weights are sometimes used in kriging. The use of negative weights is not justifiable from the practical standpoint. Also, negative block grades can be obtained in some extreme situations which makes no practical sense. To guarantee non-negative weights an additional constraint is required in the kriging system of equations. Unfortunately, the nonnegative weight constraint results in a set of non- linear system of equations. In this paper, a derivation of the resulting set of nonlinear equations is presented and a numerical algorithm is developed for the solution of the equations. Because the algorithm developed does not remove negative weights arbitrarily, optimal nonnegative weights are always guaranteed. Results obtained using the developed algorithm were compared with those using the standard linear kriging, in terms of computer time and the estimation results. Both the computer time and the kriging variance were found to be higher with nonnegative constraint, as expected. However, some systematic pattern was observed in the kriged values (i.e., over or under estimation) with or without the nonnegative constraint. The study also demonstrated when one should generally expect negative kriging weights in practice, and what practical impact the negative weights can have on the kriging estimates.

Jan 1, 1984

By W. P. Arnott, P. Nascimento, X. L. Wang, K. C. Kocsis, S. J. Taylor, H. Firouzkouhi

We report the first spectral photoacoustic measurements of silica, coal, and kaolinite dust absorption coefficients from 11 to 13 μm at 5 nm resolution made with a tunable quantum cascade laser. This is important because airborne silica dust and coal dust within mining environments continue to be a problem for mine workers and staff due to their severe health effects on the respiratory system, while other dust types are potentially interferents to their detection. Our real-time spectra compare favorably with the non-real-time filter-based Fourier transform infrared spectrometer (FTIR) spectra obtained using the sampling system developed by NIOSH for their end-of-shift method to determine silica dust concentrations using a portable FTIR. We discuss our new dust generation system and instrument testing chamber. We also show that our PM4 silica mass concentration measurements by a low-cost air quality sensor (SPS30) are in good agreement with the TSI Aerosol Particle Sizer instrument, the NIOSH end of shift method, gravimetric mass, and correlate well with photoacoustic light absorption measurements at a wavelength where silica absorbs strongly.

Aug 20, 2022

By Yanan Zhang, Hongwei Deng, Feng Gao, Bo Ke

Recently, liquid carbon dioxide (L-CO2) blasting technology has attracted attention due to its good fracturing effect and safety performance, especially in coal seam permeability improvement. This paper analyzes the blasting effect of L-CO2 based on experiments and studies the fracturing mechanism from the perspective of stress wave action via theoretical analysis and peridynamic simulations. The results indicate that L-CO2 blasting achieves a good fracturing effect without forming a crush zone, and the loading rate and strength of the stress wave are key factors.

Jan 19, 2022

By Jalal Vakili

In designing very large excavated slopes which are becoming increasingly common in both mining and civil engineering projects, the most important decision of the engineer is the selection of a slope angle. The purpose of the geotechnical study of the slope is to ensure reasonable stability of the slope in the most economical way. Because the rock mass composing each slope is unique, there are no standard solutions for slope stability analysis. A practical solution is formulated from the basic geologic data, engineering properties of the rock, geometry of the slope, and ground water observations. Stability analysis consists of analyzing the forces causing and resisting slope failure. There are several methods of slope stability analysis. The limit equilibrium method evaluates the overall stability of the sliding mass just on the verge of slip, using some or all of the three equations of static equilibrium of a plane problem. The stress-strain relationships of the rock mass are not considered. Method of analysis include the assumption of the shape of the slip surface. Peterson (10) introduced the Swedish method of analysis in 1916, which is based on cylindrical sliding surfaces. Fellenius (4) in 1926 extended this method and introduced the method of slices. This method was refined by Bishop (I) in 1955 and later used by Morgenstern and Price (8) in 1965. In many cases layers of extremely soft strata or strata weakened by neutral stress cause failure to take place by translation along plane of weakness instead of by rotation on a circular surface. In this paper, a slope with a horizontal layer of weak meterial is selected for analysis. This is a usual case for open pit lignite mines where lignite seam may be non-cohesive and &apos;weaker than the overburden rock or a soft clay layer underlies the seam. It is also a common case of rock fill dams supported on a foundation stratum of clay where the strength of the clay layer is less than that of the rock fill. It is shown that utilizing this method, the location of potential failure surface and the value of the minimum factor of safety can be calculated directly and the trial computations of factors of safety for a number of assumed failure surfaces are not necessary.

Jan 1, 1982

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

A ventilation study using tracer gas was conducted at a western US coal mine. The objective of the study was to evaluate the movement of longwall face air exchanges between the face and worked-out area and to document the presence or absence of face airflow pathways between these locations. The mine operator uses a bleederless longwall ventilation system with a back return and a blowing mine ventilation system. The study was conducted on an active panel and included both underground and surface monitoring sites. The study used sulfur hexafluoride (SF6) released as a slug on the longwall face and in the front of the gob inby the face. The velocity of the tracer gas movement in the gob was 0.019 m/s (3.7 fpm). The rate of movement for the overall tracer gas slug averaged about 0.0091 m/s (1.8 fpm). A separate tracer gas test initiated with the release of SF6 into the legs of the first shield showed the existence of more than one pathway of face air in the general direction from the headgate towards the tailgate corner. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob. A more detailed characterization of longwall system air and gas movement allows a mine to better assess its ventilation design for controlling gas on the face and in the gob.

By G. G. Gold

A leach pad’s fluid flow characteristics greatly affect the recovery of metals from heap leaching. However, because there are other factors such as particle size distribution, application rate and method, and chemical reactions to consider, mining companies often overlook potential problems associated with fluid flow until it is too late. In an effort to better understand the dynamics of fluid flow in leach pads, a series of experiments were preformed using temperature probes. A model leach pad was set up using a particle size distribution, fluid application rate, and application method common to modern leaching methods. Variable water temperatures were applied in succession and data gathered from the three dimensional grid of temperature probes built in to the model. Current work is analyzing these data along with visual observations of the model, computer simulations, past mining experiences, and other related research, in an attempt to develop a low cost test that could be performed prior to large scale leaching to determine the fluid flow characteristics of a particular ore. This paper will summarize the work and findings to this point as well as suggest areas of additional related research.

Jan 1, 2004

By Fulian He, Jianhang Chen, Dongdong Chen, Shoubao Zhang

"The Wangjialing Coal Mine is the main colliery of the China Coal Huajin Energy Limited Liability Company. The average thickness of the coal seam in District 201 is 6.21 m. Fully mechanized longwall mining was used in this district. The ventilation roadway of panel 20102 was influenced by the retreat mining of the adjacent panel 20104. Therefore, large deformation and severe roof falls occurred in this roadway, seriously influencing the safety production of this coal mine. To support the roadway, cable truss was proposed to strengthen the reinforcement of this ventilation roadway. First, numerical simulation was used to optimize the reinforcement parameters, including the cable installation angle, cable length, and eccentric distance. Based on numerical simulation results, in-situ tests were conducted in the ventilation roadway of panel 20102 with the cable truss technology. In-situ monitoring results showed that the roof-to-floor convergence and the convergence of roadway on two sides were within the safety range. Furthermore, no apparent separations occurred in the roof. These indicate that based on the designed parameters, the cable truss system can effectively maintain the roadway stability under the severe influence of the adjacent longwall mining.INTRODUCTIONCable bolts are flexible tendons composed of multi steel wires, which are wound into a strand (Chen, Hagan, and Saydam, 2018). They were initially introduced in the hard rock mining industry in the 1960s. Later, they found rapid application in coal mines to maintain the stability of excavations (Wang et al., 2015).The standard cable bolt is composed of seven steel wires with a diameter of 15.2 mm. Laboratory and in-situ tests showed that there is a low bonding capacity between the standard cable bolt and the grout (Craig and Holden, 2014; Chen, Hagan, and Saydam, 2018). Then, modified cable bolts are developed based on the standard cable bolts. They are improved by changing the surface geometry of standard cable bolts, such as birdcaged cable bolts (Hutchins et al., 1990) or nutcaged cable bolts (Hyett et al., 1993). Further tests proved that modified cable bolts have better mechanical interlock and friction between the cable bolt and grout, leading to larger load transfer capacity of cable bolts.Although cable bolts have been used for many years, failure of the cable bolting system still occurs. A common failure mode is the damage of surrounding confining medium while the cable bolt is still hanging in the roof, which is caused by the bond failure of the cable/grout interface (Hutchinson and Diederichs, 1996). To prevent the cable bolting system from failing, the cable truss system is more widely used in mining engineering."

Jan 1, 2019

By Raymond E. Zimmerman

The cleaning of coal by the use of jigs is one of the oldest methods of separating coal from its impurities. Although in many situations jigs have been replaced by other methods, by far the largest percentage of coal today is still being cleaned by some form of jigs. Some piston- or plunger-type jigs are still in use throughout the world; however, the greater number are air pulsated, generally called the Baum jig, named after the original inventor, Fritz Baum of Germany. This standard jig, with slight modifications, has been in use for over 75 years. Up until recently, however, it has had certain limitations in obtaining the high performance and efficiencies required in modern coal preparation practice. TO improve its performance, some radical modifications have been made in its design and operation SO that there is now a Baum-type jig giving much higher performance in terms of capacity, efficiency and sharpness of separation- This new jig is called the Batac, and the purpose of this paper is to describe its characteristics and present data giving its performance in treating coarse and fine sizes of coal.

Jan 1, 1974

By J. S. Lewis

Beneficiation and physical and chemical processing of non-terrestrial materials borrow strongly from terrestrial experience, but also involve the necessity of handling literally un-Earthly feedstocks, reagents, and environmental conditions. The present state of scientific and engineering understanding of the processing of non-terrestrial minerals, gases and hydrocarbons is reviewed with the production of rocket propellants, life-support fluids, structural metals, and refractories as the goal.

Jan 1, 1992

By Scott O’Brien, Richard Williams, Camilo I. Mejias, Elias Godoy, Javier Sierra

High-rate thickeners play a critical role in tailings management by enhancing water recovery and increasing solids concentration. However, these units face operational instability due to fluctuations in feed solids, flow rate, and flocculant response typically managed in manual mode with delayed corrective actions. This work presents an adaptive automatic control algorithm designed for dynamic thickening environments. The algorithm integrates real-time measurements of feed density, rake torque, bed level, and turbidity (overflow), optimizing the underflow slurry density while minimizing suspended solids in the overflow. The proposed control strategy is modular, simple, scalable, and applicable to both existing and new thickening systems, offering a robust alternative to manual operation in increasingly demanding metallurgical environments.

Feb 22, 2026

By F. Segobia, H. Lozano, M. Portal, F. Ysla, L. Goicochea

This case study evaluates the long- term physical stability of various historical mining structures remediated by the Center for Mining Environmental Research and Studies (CIEMAN) in Hualgayoc, Cajamarca, Peru. The region has a long history of mining activity, with remnants dating back to pre-Inca times. CIEMAN has assumed responsibility for remediating 286 environmental liabilities in the area, including adits, shafts, pits, tailings, and waste rock dumps. The study analyzes the methods employed to stabilize these structures, including geotechnical engineering techniques and revegetation. Long-term monitoring results are presented, assessing the effectiveness of remediation measures and predicting the future stability of the structures. This study highlights the importance of responsible remediation of mining environmental liabilities to ensure the safety and sustainability of communities and ecosystems affected by historical mining.

Feb 1, 2025

By J. R. Koehler

Yield pillar-based gate road designs oftentimes fail to provide mine operators with adequate ground control because of the unknowing misemployment of "critically" sized pillars. A "critical" pillar is one that is too large to either yield nonviolently or yield before the roof and floor sustain permanent damage, but is too small to support full abutment loads. To demonstrate the critical pillar concept, a field study of a tapering gate road was conducted by the U.S. Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m-wide design more closely approaches proper yield pillar dimensions. Probehole drilling of several 1 O.6-m-wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1995

By L. M. Litz

The results of a study are presented in which gaseous oxygen was dissolved in the leach liquor at concentrations of the order of 300 parts per million. This oxygen-containing solution was injected into portions of a field being operated on a commercial basis with hydrogen peroxide as the oxidant. Comparative results indicate that were concentrations and production rates were essentially equivalent with these two oxidants.

Jan 1, 1980

By A. K. Clarke

In any treatment process that requires a coarse feed material to be reduced to a fine size by crushing and/or grinding it must be determined whether a wet or dry comminution system should be utilized. All factors must be evaluated in reaching the decision. Among these factors are: 1) Ecology and Plant Environment: Unfortunately in many instances the decision on wet or dry is based on prejudice resulting from an unnecessary fear of dust. The writers submit that this fear, although once justified, is no longer valid because technology and equipment is now available to collect dust to meet any standard. When dry grinding is used it is very often possible to discard a portion of the waste product in a dry state. This will decrease the size of the tailing pond required. As pollution control standards increase it becomes increasingly difficult to clean up water from tailing ponds. 2) Operating Costs: Steel wear is often five or more times greater in wet grinding than in dry grinding. This is mainly due to corrosion. The evaluation of the economics of dry grinding must of course include the air system and dust collection; similarly in a wet grinding plant related pumping and material handling costs should be included. Pumping costs are often overlooked. This assumes water is made to flow for nothing. Pumping can account for 20 percent of the power consumption in the grinding plant. Large scale comparative tests were conducted in a wet and dry commercial plant in 1970. The same ore was used for both tests. With all factors included in both plants the dry system showed lower horsepower per ton.

Jan 1, 1971