Search Documents

By Bobby G. Cahoon

The ( ) Tayaaja ( ) . The deposit ( ) 130 kilometers due east of the continental divide and approximately 290 kilometers east-southeast of Lima (Figure 1). Relief in the immediate vicinity of the mine, which lies or the west side of the Mantaro river, is in excess of 2,000 meters, and the elevation varies from a low of 2,000 meters above sea level on the Mantaro River to a high of 4,386 meters at point T-27 (Figure 2). Although the Cobriza deposit was first reported by the Italian Geographer Antonio Raimondi in 1866, only three reports have been published on the deposit, which began production in 1966 (Duefias, 1908; Fernandez Concha and Garcia y Garcia, 1961; Petersen. 1965). Many private reports have, however, been written by geologists employed by the Cerro de Pasco Corporation. These reports and the author's observations, while employed as the Cobriza Division Mine Geologists form the basis of the present paper, which describes the relations between-the ore controls in the Cobriza mine and the regional and local structure.

Jan 1, 1971

By Z. Hyder, A. Urquidez

"INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is located approximately 26 miles southeast of Carlsbad, New Mexico and is the nation’s first underground geologic repository for transuranic (TRU) and TRU-mixed waste (see Figure 1). The WIPP facility was opened for operation in 1999 when the first TRU waste shipment arrived at the WIPP facility for disposal.WIPP facility does not employ typical production aspects of a conventional mine. Instead, the mining focus is on the quality of the excavation to ensure safe disposal of TRU and TRU-mixed waste (Walls, 1991). GEOLOGY WIPP underground repository is mined within a 2,000 feet-thick bedded-halite formation (Salado Formation) (see Figure 2). The WIPP underground repository is located approximately 2,150 feet beneath the surface near the center of the Salado Formation. Geologic criterion and site-selection factors evaluated for the selection of the repository included topography, depth, thickness, lateral extent, lithology, stratigraphy, structure, erosion, dissolution, subsidence, surface water, aquifers, hydrologic transport, climatic fluctuations, manmade penetrations (U.S. Department of Energy, 1980).FACILITY DESIGN Profit did not play a major role in the WIPP’s conception like in a conventional mine. This was due to the extensive amount of additional regulations and safety controls that had to be built into the WIPP facility. Since it is nuclear and hazardous waste disposal facility, it must meet certain federal and state requirements for TRU-mixed waste. One of the major regulatory drivers for the WIPP facility is defined in the WIPP Land Withdrawal Act (LWA). One of the requirements in the WIPP LWA requires the DOE to submit documentation of continued compliance with Title 40 CFR Part 191, Subparts B, and C. These standards are regulated by the Environmental Protection Agency (EPA). The DOE must submit documentation of continued compliance (recertification) with these regulations every five years. In addition to the LWA, the Resource Conservation and Recovery Act (RCRA) is another major regulatory driver for the WIPP facility. Since the WIPP facility is categorized as a “Miscellaneous Unit” under 40 CFR, it must meet extensive environmental performance standards. These standards are defined in the WIPP Hazardous Waste Facility Permit (HWFP). The HWFP defines the terms and conditions that the Secretary of the New Mexico Environment Department has determined necessary to protect human health and the environment (U.S. Department of Energy and Nuclear Waste Partnership LLC, 2015)."

Jan 1, 2017

By J. J. Reilly

The Vesta Mines of the Jones & Laughlin Steel Corporation operate in the Pittsburgh Seam in Washington County, Pennsylvania. This seam is overlain with a drawslate, 12" to 16" in thickness, which slimes readily when wet. Because of the need for a uniformly good quality metallurgical coal, the amount of reject, together with the top and particle sizes of the raw coal feed, is a serious problem at the Vesta Preparation Plant. The Preparation Plant operates two, seven and one-quarter hour shifts per day and processes 2,100 tons per hour of raw coal feed. The third shift is, used for planned maintenance of equipment. Since the water clarification equipment is so vital in insuring a uniform product, there is no alternative but that it be in operation at all times. To insure this continuous operation,. well-planned maintenance is a necessity. For years, Plant Management has kept performance records of the various units to determine the renewal dates of vital component parts, the length of wear, the various materials used in the manufacture of the equipment, and the labor cost for renewal. These records have been of inestimable help in planning an effective maintenance program to insure continuous operation of the various units.

Jan 1, 1959

By Donald M. Hausen

Microscopic evaluation of trace quantities of metalliferous phases in flotation products requires counting large numbers of particles. Particle counts of many thousands may be required for precision, but not obtained practically by conventional microscopic techniques. A less tedious microscopic method for evaluating trace sulfides in mill tailings was developed for the O'okiep Mining Company in South Africa. Hundreds of thousands of particles were evaluated by this method called "gross-counting." Gross-counting consists of counting microscopic fields rather than point-counting individual particles. Total counts are calculated by multiplying the average number of particles per field by the total number of fields examined over the entire mount. Total gross-counts range from about 20,000 particles for +200 to 100,000 or more for -400 mesh size material in lucite mounts. Sulfides and metallic particles in each field are identified and tallied along with field counts. Totals for each type of metallic particle are divided by the total gross-count to give volume percent which is corrected to weight percent by specific gravity factors.

Jan 1, 1969

By Peter McKenna

Different reefs being extracted from a mine will, in all likelihood, have significantly different semi-variogram models - and these will probably vary from geozone to geozone. As errors of estimation are dependent on the semi- variogram parameters, it follows, if a mine samples all reefs in all sections using the same sampling grid pattern, that estimation errors (or limits of confidence) will not be the same throughout the mine. This may be an undesirable situation! A geostatistical study of the relative merits of alternative sampling arrangements has been carried out by considering different reefs in different sections of a South African gold mine.

Jan 1, 1989

By Steve Kral

The mining industry has waited a long time for the resurgence in commodity prices and demand for its products that it is now experiencing. Base and precious metals prices have reached levels not seen before. Coal prices have also shot up. And there are encouraging signs in the uranium market. China’s nearly out-of-control economic growth is said to be the leading driver for much of this resurgence. But demand for energy, metals and building materials in the United States and elsewhere are also major factors. The result is that expansions and new mines for nearly every commodity are in the works.

Jan 1, 2005

By Valeh Aghazadeh, Shima Barakan, Mina Soleymani, Ehsan Bidari, Morovvat Faridazad

Molybdenite is the most important molybdenum concentrate, which is mainly recovered as a by-product from porphyry copper deposits. Due to the low efficiency of purification processes such as flotation in the reduction of copper content of molybdenum concentrate to a standard level (i.e., less than 0.5 wt.%), further purification by a hydrometallurgical method is required. Although different types of chemical reagents were found to be effective in the leaching of copper minerals from molybdenum concentrate, the mechanisms of these processes remain largely unexplored. In this study, optimal conditions for maximum copper leaching (> 99%) were obtained at the concentration of HCl = 1 M, FeCl3 = 0.5 M, CuCl2 = 0.05 M, CaCl2 = 0.5 M at 75 °C, 500 rpm, and S:L = 1:10 during 60 min. CuCl2 was identified as the most effective leaching reagent for copper dissolution in agreement with Visual MINTEQ model results due to the formation of various types of copper chloride complexes. Furthermore, the electrochemical behaviors of FeCl3, CuCl2, and CaCl2 reagents before and after the leaching process were investigated by the cyclic voltammetry technique. The results of cyclic voltammograms at different scan rates verified the presence of copper chloride complexes, and ferric ions as the oxidizing reagents for better dissolution of copper sulfides. Based on kinetic study results of shrinking core models, both chemical and diffusion reactions controlled the copper leaching process with an obtained activation energy of 33.56 kJ/mol. For recovery of the leached copper, the precipitation process was done by the addition of Na2S at 45 °C, S/Cu = 1, and pH = 9.

Dec 26, 2022

By Ulrich O. Lange

Coal is America's most abundant energy resource. Therefore, it IS logical to assume that coal must be produced in much greater quantifies in order to make the United States self-sufficient, as far as energy is concerned by 1985. However, there are a number of obstacles which have to be overcome in order to achieve such a great task. According to one of the most outspoken American Mining men, there are three major obstacles. Those are: (1 ) Mining technology (2) Public image of the coal mining industry (3) Governmental policy toward the mining industry The following will be dealing with Shortwall Mining, which is a very specific part of mining technology and which might influence the image of the coal mining industry as well as the governmental guidelines, at least to make it easier to live with those guidelines. During recent years the operation of coal mines has been more expensive than ever. Since 1970, the cost of producing coal increased by 30% and the productivity dropped by just about the same amount. Those are alarming signs.

Jan 1, 1975

By D. R. Spears

The U.S. Bureau of Mines has developed a Fast Air-injected hydrocyclone-Shallow Tank (FAST) flotation system. Conventional flotation cell kinetics are a compromise between two conflicting requirements, the need for an agitated zone for rapid bubble-particle collision, and a quiescent zone for bubble-pulp separation. The Bureau of Mines has designed a flotation system in which bubble-particle collision and bubble separation are carried out in two discreet unit operations. A bubble slurry was mixed with an ore slurry at a high rate in a modified air-injected hydrocyclone for rapid bubble-particle collision. The mixture was then fed into a unit specially designed for rapid separation of the bubbles from the pulp. A conventional flotation cell required 2.8 min to obtain 90 pet recovery at a 7-pct Cu rougher concentrate grade, whereas the FAST flotation system can obtain 85 pet recovery with a 13-pct Cu rougher concentrate grade in 0.28 min, and 92 pet recovery with a 7-pet Cu grade in 0.56 min. The Bureau's FAST flotation system is adaptable to a wider variety of flow sheets and could potentially allow for replacement of conventional flotation cells with smaller and faster units.

Jan 1, 1991

By Mark E. Gershon

Extensive efforts are under way to- ward applying computer techniques to mine production scheduling problems. These efforts are concentrated in four areas: optimization, computerization of traditional methods, heuristics and simulations. These areas complement each other rather than compete. Characteristics of each are discussed toward enabling the engineer to evaluate specific systems that may be encountered. Alternative approaches within each classification are described as well as the motivation for each.

Jan 1, 1985

By W. Petruk

Imaging is a fundamental requirement when characterizing minerals, ores and related products. Images are used for presentation, texture analysis, characterization, image analysis, identification, etc. The image mode that is utilized is dependent upon the application, mineral properties and available instruments. Different instruments produce images that display different features; in order of increasing complexity they are: hand specimens, a non-polarizing microscope, polarizing optical microscope, scanning electron microscope (SEM), low vacuum SEM, microprobe, secondary ion mass spectrometer, staining, cathodoluminescence, tomography and others. Image analysis uses images produced with either an optical microscope or a SEM, but the SEM images are superior in this application.

Jan 1, 2001

By A. T. Yu

There are compelling reasons for us to look to our Country's Western coal. Despite its inherent low BTU content, Western coal's low sulphur content provides a near-ideal answer to satisfy our in- dependent goals of clean air and self-sufficiency in energy. Vast reserves, thick seams and amenability to low-cost strip mining serve as a powerful economic basis for its viability as a primary and dependable source of energy for the coming decades. A major consideration, the solution of which may not be quite obvious, is transportation cost. These abundant deposits are remote from the utilities of the heavily populated eastern regions of the United States (Figure 1). A Western coal mine in Montana is likely 1500 miles or more from an eastern power plant. The comparable distance to an eastern coal mine may be only 200 miles. Thus, the question is: How can the haulage cost of our Western coal be substantially reduced to an acceptable level? If resolved, western reserves of coal will be one of the key solutions to satisfying our Nation's energy needs.

Jan 1, 1975

By Sheldon P. Wimpfen

Back in 1970 Congress passed the National Mining and Minerals policy Act, which had as one of its basic tenets to rely on a strong and stable private minerals industry for the development and production of our mineral resources. Since then, a substantial amount of legislation has been introduced that impacts on the minerals industry. Although most of the bills proposed are not passed into law, each bill affecting minerals and mining is given careful review by the Bureau of Mines. Comment is forwarded with the object of being helpful to legislators by providing our assessment of the probable impact of each bill proposed along with suggestions to improve them. Actually few bills introduced become law. For example, in the 93rd Congress 4,260 bills were introduced in the Senate and 17,690 in the House. In the final accounting there were passed 123 private laws and 649 public, 3 percent of the bills introduced. There would be little merit here in attempting to analyze each mineral-related bill that was proposed. Many are similar and aim at making a certain aspect of our minerals activity fit needs. So, to simplify the task the many bills have been grouped by subjects. Slide 1 shows the principal topics and the number of related bills introduced. Putting it altogether, there are 26 principal subjects and almost 200 bills. And these numbers are probably off somewhat, as this accounting was made early in December.

Jan 1, 1976

By Richard W. Amerman

The final cost and quality of a project employing equipment, labor, and materials is dependent upon the expediency and extent to which each of these parameters are used. An ideal solution then, would be one in which three solvable equations were given for each particular situation. The equipment, labor, and materials could then be solved for, and the perfect job would result. In reality, however, the ideal and most economical solution is seldom attainable by solving three given equations. Therefore, knowledge, experience, and sometimes guesswork must be relied upon when correlating equipment, labor, and materials. Drilling and blasting, in particular, is one operation which normally involves more uncertainty than other operations. It is also an operation in which the outcome is extremely critical for two reasons. First, the cost of the operation that follows drilling and blasting is dependent upon how well the material is fragmented. Second, once the drilling and blasting has taken place, it is impossible to return to the area, without considerable expense, and correct any mistakes that might have been made. Therefore, what is desired is a method by which drilling and blasting operations can be performed yielding optimum results at the lowest cost; this can best be accomplished by having the relationships between equipment, labor, and materials prior to their use. For obtaining best results, the selection of these three relationships must be based on knowledge, experience, and as little guesswork and uncertainty as possible.

Jan 1, 1969

By Kenneth W. Luke

In the development of the ultimate pit limits for a narrow ore body, pa¬rameters necessary in the design of a functional, or working, pit become highly sensitive factors in the determination of ore reserve levels and their associated waste to ore stripping ratios. Through the use of geologic cross sections, ore reserves can be roughly calculated by utilizing a straight line approximation for pit wall slopes. The optimum position of the pit floor can be substantially altered from such a preliminary design though with the introduction of functional mining parameters, such as a ramping network, and working bench heights, berm widths, and bench to bench wall angles. Originally a computer program was developed to quickly evaluate changes in cross-section pit design with minimal alteration of input data. After developing a satisfactory technique of cross-section evaluation which incorporates working mine parameters, an optimization algorithm, or procedure, was developed and included in the program to eliminate much of the tedious manual decision-making required in determining the optimum location of the pit floor on each cross section. Optimization in this case implies the maximum profit pit. When pit and processing costs are defined or hypothesized, this computer program can be used to design the maximum profit pit, constrained by the recognized functional mining parameters. A second way of stating the optimization is that the program can be used to develop a pit design which minimizes waste stripping at any desired ore reserve level. The basic method of cross-section evaluation parallels present manual methods. Program input is a combination of data obtained directly from cross sections developed for, geological interpretation and pit design parameters selected by the mine planner. As a result it is easy for the mine planner to comprehend what the program is accomplishing, and thus participate in the development of the computer assisted design.

Jan 1, 1971

By Georgene Renner, William R. Yernberg, William Gleason

American Commercial (ACI) offers a selection of ground control solutions. Beginning with steel liner plates installed in the Gratiot Avenue sewer system in Detroit, MI 1920, ACI is one of the leading designers and manufacturers of underground steel supports in North America. ACI is also a leader in fire-proofing underground structures with its Promat Fire Protection Boards. The sandwich panels have been used in many new and retrofit tunnel and underground construction projects worldwide. Ease of installation and replacement, cost effectiveness and superior performance have made this product line the premier choice of owners and designers for structural protection, fire-life safety requirements and architectural finish needs.

Jan 1, 2007

By B. A. Hillman

Silicon is the second most abundant element on earth, exceeded only by oxygen. Silicon dioxide forms a crystalline structure of repeating SiO2 molecules which form characteristically hard, durable crystals. As a result, crystalline silica is Ubiquitous in the crustal rocks, sediments and the mineral products derived from mining. An examination of the history of studies that identify silica as a human and animal carcinogen is presented in the context of the development of a public health policy in California. The implications for the cost of conducting aggregate and other mining operations in the state are discussed.

Jan 1, 1992

By D. P. Gold

Major sources and reserves of Cb/Nb, Ta, REE, Y, Sc, Zr, Hf, Cu, apatite and vermiculite may be concentrated in primary and secondary minerals associated with different stages and depths of emplacement in carbonatite complexes and kindred alkalic intrusive rocks. Exploration targets include: apatite and pyrochlore (Nb) in the plutonic and hypabyssal core and ring-dikes: bastnaesite (REE), strontianite, barite and fluorite in hydrothermal veins and cone-sheets (subvolcanic setting): thortveitite (Sc,Y) and vermiculite in metasomatized aureoles (fenites): high grade eluvial deposits of apatite and pyrochlore, and secondary REE, Nb, Ti. and V-minerals in supergene and weathered zones.

Jan 1, 1991

By John E. Caffrey

United States Steel Corporation began mining coal in southern West Virginia at the turn of the century, and until the late 40's production was confined to underground mines. Surface mining was initiated in our southern West Virginia -holdings as a means of recovering coal that could not be obtained by underground mining methods. After observing and evaluating surface mining methods employed by other companies, some of which operated on lands of U. S. Steel on a lease basis, we undertook the establishment of a surface mining operation. Our method, as, initiated in the early 50's, remains basically the same today. Variations have come about primarily by equipment modifications. The method consists' of a pioneer cut to establish the coal outcrop, a drill bench for drilling, blasting, and removal of the overburden from the top of the coal. The land is rugged except for the flood plains of some of the larger streams. The mountains have steep slopes, averaging 30 degrees, with relatively sharp ridges and very narrow valleys,. Geologically, the coals_ lie in the Pocahontas formation of the Pottsville group in the Pennsylvanian system. This means that the coals in our area of operation lie at the base of. The coal measures in the Appalachian range. The coal that we have mined is primarily the Pocahontas nos. 3 and 4 seams. We have mined negligible amounts of other seams in the Pocahontas groups above the no. 4 seam. The Pocahontas no. 3 seam, which is the lowest mineable seam geologically in this area, lies anywhere from 700 feet below: the valley floor up to 400 feet above the floor. This is occasioned by the Anticlinal formation which gives us grades Of about 9% at the anticline, decreasing to about 1 to 1-1/2% on the extreme flanks. We have the opportunity to engage in surface mining where the coal seams intercept the surface above the valley floors.

Jan 1, 1972

By Trenton Cohen, Joseph McDivitt, Shimi Tzobery, Joseph Sinacori, Scott Zylstra

The 2-mile Beach Interceptor Sewer Tunnel was constructed in 1954 to then-current mining and construction standards. Due to its lifespan and deteriorating condition it is now being stabilized and rehabilitated using conventional excavation and ground support. At its southern end, below the prestigious Three Arch Bay community, the original tunnel alignment passes under a historic landslide where the tunnel was sand-backfilled and capped by bulkheads in 1957 due to severe and caving ground conditions. Video footage of the existing 21- inch clay pipe showed that the pipe is severely damaged, which could potentially cause a catastrophic pipeline failure and sewage spill into the Pacific Ocean. This paper summarizes the thorough investigation and design process, tunnel realignment construction and monitoring, and the notable cooperation between all parties to overcome the project risks.

Dec 1, 2022