Search Documents

By D. R. Hack

Increased consumption of concrete in the Pacific Northwest has pushed aggregate resource development pressure from urban areas west of the Cascade Range to rural areas east of the Cascades. Some recent development has focused on barge and rail accessible off-reservation Indian allotments that are exempt from state and county regulations. These lands have their own unique set of challenges, especially when Federal and Tribal governments have conflicting goals and attitudes pertaining to resource development. This paper discusses issues of leasing, reclamation, Federal vs. Tribal authority, cultural resources, and the history of allotment.

Jan 1, 2002

By Bobby P. Faulkner

Allis-Chalmers has combined a new heat transfer device, called the ROLLER GRATE, with a unique processing scheme, resulting in the ROLLER GRATE Oil Shale Processing System of Allis-Chalmers. In order to test both the process and the equipment, a batch Process Development Unit (PDU) ROLLER GRATE retort was designed and built. This unit vas designed with the flexibility to process shale over a wide range of test conditions in order to demonstrate the attributes of the oil-shale processing system. Instrumentation on the PDU and extensive sampling of the effluent streams permitted the PDU test data to be used in the design and scale-up of the process. Over 30 tests have been conducted with Colorado shale, and over 25 tests have been run with an Indiana shale. In addition, rests have been run with California and Utah tar sands.

Jan 1, 1983

By B. A. Osei

Research to evaluate possible metrics for predicting dredgeability of compact aggregates, by hydraulically actuated clamshell dredges, shows work done by the pistons as a viable metric. Analysis of field data shows that there is a low, positive, correlation between cycle time (CT) and work done. If this correlation exists, then CT has to be considered an independent variable affecting work done during dredgeability assessment. Further research is required to elucidate the relationship between CT and work done during dredging. The objective of this paper is to test the hypothesis that work done during dredging increases with increasing CT. Kinematics and dynamics of the hydraulic clamshell were modeled and implemented in Simulink® in MATLAB. The model was validated using field data. The model was then used to test the research hypothesis. The results show that work done increases with increasing CT. This work confirms that work done during dredging increases with increasing CT. This result indicates that though an operator can increase the CT to deal with difficult digging, inputting unduly high CTs results in higher energy consumption during dredging.

Jan 1, 2011

By David A. Newman

The Geomechanics Classification (Bieniawski, 1979) was modified for entry and roof support design in underground room-and-pillar coal mines. Adjustment multipliers were introduced to incorporate the influence of strata weatherability, high horizontal stresses, and the roof support reinforcement factor into the existing classification system. Sixty-two case histories of both standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant impact upon the supported stand-up time of coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1985

By James M. Barker

The borate deposits of Death Valley, first exploited in 1882, were a major world source of boron-bearing products until shortly after very large deposits near Boron, California (Kramer) came on stream in 1926. Borate mining in Death Valley then became moribund, with most extant deposits held as reserves backing Kramer. Tenneco began borate operations following acquisition of claims in 1967 and is the only active borate producer inside Death Valley National Mon¬ument. Borate ores, confined to the lower Furnace Creek Formation (early to middle Pliocene), initially precipitated in a shallow lake fed by boron-rich volcanic hot springs associated with the Basin and Range province. Later diagenesis and remobilization plus regional folding, faulting, and erosion altered and complicated originally simple borate mineralogy and distribution. Dominant ore minerals are ulexite (NaCaB509.8H20), probertite (NaCaB509.5H20), and colemanite (Ca2B6011.5H20). Tenneco currently operates two open pits near Ryan, California. Mining is by bulldozer-pushed scrapers hauling waste and front-end loader/off-highway truck combinations for ore and waste haulage. Archeological, environmental, and aesthetic considerations influence both mine plans. Boraxo Pit, opened in 1970, has deep ore (stripping ratio 10 to 13:1) which occurs along a fault and as beds in shale on the hanging wall. Problems include pit wall instability (adverse bedding), non¬ripable calcareous shale (11,000 fps), and mixed ore separation. Sigma Pit, opened in 1975, has shallow (stripping ratio 1 to 1). low dipping, bedded ore in shale. Massive ulexite and "granular" un- cohesive colemanite present problems in mining and milling. Colemanite is crushed to -6 inches, washed, dried at 350°F, then calcined at 800°F with 100 tpd capacity. Crushed (-6 inch) ulexite or probertite is Raymond milled to customer specifications with a capacity of 1000 tpd.

Jan 1, 1976

By I. J. Lin

The effect of various types of structural modification on the critical micelle concentrations (CMC) and hydrophile lipophile balances (HLB) of certain surfactants has been considered. Using the concept of effective chain length for the substituted species, an index of hydrophobicity (I) has been defined. It is hoped that such an index will allow one to choose surfactants for particular purposes in a less arbitrary fashion than heretofore.

Jan 1, 1973

By Robert C. Maxton

The foundry industry is a basic source of structural component for all industry. Millions of tons of castings are produced annually in both ferrous and nonferrous alloys. These castings are subjected to a wide variety of heat treatments, finishing techniques, mechanical tests and machining operations. Through all of these steps the quality of the casting is of paramount importance to the end use of the product. The Quality Assurance Program at Minneapolis Electric Steel Castings Company is designed and established to provide a superior product for both original equipment manufacturers and the mining industry.

Jan 1, 1982

By Robert D. Coale

This paper will describe the copper concentrate slurry pipeline and pumping system between the concentrator and the port at Bougainville Copper Ltd. The operations of Bougainville Copper Ltd. are located on the island of Bougainville in the South Pacific. Geographically, it is the northernmost island of the Solomon Group but, politically, it is part of Papua New Guinea. Papua New Guinea is a United Nations Trust territory administered by Australia, having recently been given self-government, with independence scheduled for December 1974. (Fig. 1). The island is approximately 130 miles long by 30 miles wide, with the Crown Prince mountain range forming a spine along its length. The mountains in place are over 8,000 feet high with the mine located on the western flank at an elevation of 2,200 feet. Exploration on Bougainville for copper by Conzinc Riotinto of Australia (CRA) began in 1963 and by 1968, through geophysical, geochemical and diamond drilling methods, an orebody containing nearly one billion tons of ore grading approximately 0.48% Cu. and sane gold had been outlined. Bougainville Copper Ltd., the company operating the mine, is 53.6% wined by CRA, 20% mined by the government of Papua New Guinea with the public Folding the remainder of the shares. The first copper concentrate was produced in early 1972, with production for the first full year, 1973 being:

Jan 1, 1974

By David A. Greenhut

The Kubota surface melting system has been under development since 1975. It has found commercial application on the melting of municipal sludge, and ash from solid waste. The melted product has physical properties allowing its use as a substitute for aggregate in cement and asphaltic construction. This paper describes the surface melting system, its current use and anticipated future use.

Jan 1, 1991

The recovery of coarse particles has been widely recognized as being limited by the froth in mineral flotation. In response to this, FLSmidth has developed the Selective Froth Recovery (SFR) System. The SFR System is an extraction system that vacuums material from select locations within the froth and separates the recovered solids into coarse and fine fractions with a hydrocyclone. The SFR is supported and located by an actuator connected to the cell?s level control so that the suction heads are maintained at an offset distance from the slurry level. This can increase the recovery of coarse material by selectively recovering the material close to the bottom of the froth where drop-back of coarse particles typically takes place. The SFR System has been tested at two separate mine sites, and has been proven to increase the copper recovery in both trials. TEST RESULTS The SFR prototype was installed in a copper recovery circuit, on a rougher scavenger 160-m3 flotation cell. Figure 1, shows the SFR System, which consists of four conical skimmer heads that are plumbed together and share a common actuator. The SFR System, raised out of the froth prior to a test, can be seen in Figure 2. The SFR prototype was able to maintain a variety of set points using the level control to determine the slurry height.

Feb 27, 2013

By W. C. Carter

In mid 1978 Inland Cement Industries Ltd. brought on-line their new one million megagram (Mg) per year cement plant at Tilbury Island, Delta, British Columbia. The Plant--Its Philosophy of Design The design of this plant began in 1974, at the beginning of the rapid rise in petroleum costs later referred to as the "energy crisis". The trend in fuel costs was clear, so one of the basic criteria for the selection of process equipment was high thermal efficiency. Throughout the process of selection of materials handling and process equipment, energy consumption was a factor in decisions. A second factor which influenced the design of the plant was its location on navigable water. The plant is designed to make maximum use of this means of transport to minimize transportation costs. All raw materials (and some fuel) are received by water, and a major portion of the cement and clinker is sent out by barge. Extensive modern dock and material handling facilities were provided to accomplish the shipping and receiving functions. A plant meeting stringent environmental regulations was the third major factor which formed the basis for design. To meet this requirement, all storage facilities had to be covered, 53 bag type dust collectors were applied throughout the plant, and materials handling equipment was designed to minimize dust and spillage.

Jan 1, 1979

By M. Wiber, P. Nicoll

Rio Algom has embarked on a major programme of expansion with the goal of becoming one of the world’s top-performing base-metal mining and metals distribution companies. To assist the company and its operations in achieving its business objectives, we are implementing an environment, health and safety (EHS) management system, built to be compatible with the 14001 model. We recognize that a sustainable development approach for Rio Algom includes outstanding performance in EHS and community responsibility and is essential to earn acceptance within the communities where we operate or wish to locate; raise capital; obtain permits, and operate efficiently. We are committed to triple bottom line accountability, i.e. full consideration of environmental, social and economic concerns in our business decision making.

Jan 1, 2000

By W. B. Greer

The performance of seals in boreholes, shafts, and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines, and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in-situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall and others, 1982). This research involved the installation, extensive hydraulic testing, removal, and post-test examination of a l0-cm-long by 10-cm-diameter cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble peak in the Santa Catalina Mountains, Arizona. A test hole was diamond cored in the re-crystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diameter, and dips at 10.4 degrees. The hole extends between two drifts and thus is accessible from both ends.

Jan 1, 1992

By D. D. Schlepp

There is a continuing debate about the influence of circulating load and classifier efficiency on the capacity of the circuit. Specifically, the effects of preferential classification, bypassed fines, and the sharpness of classification will be examined. Horizontal cyclones have also proven to be very successful in a number of operations but their impact on the circuit capacity has not been clearly defined.

Jan 1, 1990

By Syd S. Peng, C. Y. Chen

Introduction The Surface Mining Control and Reclamation Act was passed in 1977 to put an end to the uneven environmental standards and enforcement established by various coal mining states in the US. One year after passage, the Secretary of Interior was directed to promulgate permanent program regulations implementing Title V provisions of the Act. These regulations were to form the basis for state regulatory programs under the Act and to allow states to assume primary regulatory responsibility. To implement the underground mining provision of the Act, the Secretary is directed in section 516(a) of the Act to promulgate rules. But they must take into consideration the differences between surface and underground coal mining. The regulations developed by the Secretary in 1979, with respect to subsidence control, included: • a subsidence control plan as part of the permitting process; • substantive provisions establishing performance standards for subsidence control; and • provisions providing for the prohibition of mining under perennial streams, impoundments larger than 24.6 dam3 (20 acre ft), and certain public facilities and urban areas. Industry challenged the Secretary's regulations implementing the subsidence control provisions. The litigation was consolidated with all other challenges to the permanent program regulations. (Permanent Surface Mining Regulation Litigation, Civil Action No. 79-1144; D. D.C., May 16, 1980.) In two opinions dealing with the multitude of issues raised by both industry and environmental groups, the US District Court of the District of Columbia ruled against industry. It upheld the promulgated subsidence control provisions. The US Court of Appeals stayed the appeals pending the agency's review and revision of its regulations. The regulatory reform was conducted in accordance with the order from the Secretary of Interior and the President in 1981. As a result, the subsidence control regulation was revised, reproposed, and finalized in June 1983 (Federal Register). This regulation, along with others, was again challenged by environmental groups and industry. On Oct. 1, 1984, the court, after finding the Secretary's reading of the Act reasonable, upheld the 1983 subsidence regulation except for one section. On Feb. 21, 1985, in accordance with the court's ruling, the Office of Surface Mining (OSM) suspended a portion of 30 CFR 817.121 (c)(2) concerning the damage correction requirement for structures or facilities and reproposed it on July 8, 1985 (Federal Register). In conjunction with a request for public comments, OSM now also seeks comments on the omission from the 1983 rule of the requirement in the 1979 rule regarding a presubsidence survey and monitoring of damage to structures. Technical issues related to subsidence regulations The subsidence regulations of June 1, 1983, consist mainly of two parts: a subsidence control plan as part of the permitting process; and substantive provisions establishing performance standards. The latter also includes provisions for prohibiting mining under certain areas. Under subsidence control plan section 784.20, minimum require-

Jan 2, 1986

By Madan M. Singh

This section is unique to the Handbook in that it is the only section that deals with underground excavations for nonmining purposes. The editors were of the opinion that the section should be incorporated because the subject matter covered by the chapters is closely related to mining, and many mining engineers are currently involved in these activities. As we enter the decade of the 1990s activities in this category will increase, enhancing the relevance and utility of the material discussed. As the population increases, especially in metropolitan areas, the necessity to go underground will be greater. At the present time, not only are subsurface shopping malls and pedways connecting buildings becoming commonplace, but structures as diverse as the Civil and Mining Engineering Building on the University of Minnesota campus, a road-and-fleet maintenance facility in Multnomah County, OR, and even an ice cream parlor (Dairy Queen) in northern Wisconsin have been constructed underground. Placing utilities below the surface has numerous advantages and is now customary. Rapid transit and highways through tunnels in urban areas have been the norm for many years, but subterranean stormwater reservoirs, power plants, industrial warehouses, and food storage silos are relatively new innovations. The philosophy of underground defense installations is ancient, but their requirements and designs have trans-formed radically as technology advances. The use of under-ground space for disposition of wastes is modern, since it is recently that environmental concerns and waste disposal costs have assumed increased significance.

Jan 1, 2008

By B. M. Eiter, J. Hrica, D. R. Willmer

"Mineworkers are routinely tasked with making critically important decisions about whether or not a hazard presents an imminent danger. Researchers from the U.S. National Institute for Occupational Safety and Health collected formative data to investigate mine safety professional perspectives on workplace examinations, which revealed a potential gap in how mineworkers are assessing risk. During interviews, participants revealed not having a systematic methodology for mineworkers to use to determine if a hazard is considered imminent danger. In this paper, we identify and describe three distinct categories of imminent danger complexity and discuss potential steps that could lead to improved identification of imminent danger situations. Finally, we identify potential practices to incorporate into risk management efforts, including feedback, communication and specialized training, to increase awareness of imminent danger situations. IntroductionIn recent years, the metal and nonmetal mining sector, as categorized by the U.S. Mine Safety and Health Administration (MSHA), experienced an increase in the number of fatalities occurring at mine sites. From 2013 to 2015, 69 mineworkers were fatally injured, twice the number of fatalities in each of the previous two years (MSHA, 2015a). As a way to address this increase, MSHA issued its P15- IV-01 program policy letter, suggesting that “miners would benefit from rigorous workplace examinations conducted by experienced and trained examiners” (MSHA, 2015b). The goal of these examinations is to find hazards in the field and mitigate them before they cause injury or death to mineworkers. While it is important to identify all hazards in the workplace, it is critically important to identify those hazards that are considered imminent danger because they require an immediate response to avoid a severe or even fatal injury."

Jan 9, 2018

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

The main purpose of mine ventilation design is to provide sufficient quantity and quality of air to the workers and to dilute methane and other contaminants. It is generally perceived that the additional air along the longwall face will improve methane dilution on the face and in the tailgate. However, computational fluid dynamics (CFD) modeling efforts at the Colorado School of Mines (CSM) under a National Institute for Occupational Safety and Health (NIOSH) funded research project have found that higher flow velocities along the longwall face are shown to increase the pressure differential between the gob and longwall face allowing more methane to be entrained in the active face and tailgate (TG) area, thereby negating the dilution effect. The increased face ventilation causes an increase in pressure along the headgate side which allows more oxygen to ingress into the gob area, thereby increasing the amount of oxygen available to form explosive methane air mixtures in the gob and to support spontaneous combustion of the coal. Two things are happening at two different locations along the longwall face, increase in pressure as the flow enters the active area cause an increase in pressure which forces more oxygen into the gob, but as the flow is developed along the longwall face, the higher velocities causes greater pressure drop allowing methane to enter the active face further downstream from the headgate (HG) towards the tailgate side. In this paper, a parametric study will be presented to discuss the effect that varying the face air quantity has on methane concentrations in the tailgate and formation of explosive gas zones (EGZs) in the gob. Counter to conventional wisdom, it appears that increased longwall face air quantities may increase the explosion hazard as they result in increased EGZ volumes in the gob, along with increased methane quantities in the tailgate return.

Jan 1, 2015

By Xiaoting Li, Richard Adasiak, Benjamin Mirabile

Pumpable J-Crib stopping walls and Jennmar high-strength (HS) stopping panel walls are widely used for resisting high-ventilation air pressures and roof support in underground mines due to their installation efficiency, convergence allowance, and better performance than traditional concrete block stopping walls. Based on the different entry dimensions and required maximum ventilation air pressures of up to 36-in. water gauge, 24-, 27-, 30-, and 36-in.-diameter pumpable J-Crib stopping walls, or 18- to 30-in. thick Jennmar HS stopping panel walls can be designed, and their support capacities and convergence allowances are evaluated for better roof control. Pumpable J-Crib stopping walls consist of 0.187-in.-diameter steel wire reinforced, JCrib material-filled bags, and non-wire-reinforced filler bags in between. Jennmar HS stopping panel walls consist of two, 20-gauge (0.04-in.-thick), galvanized, cold-formed steel panels with J-Seal materials pumped in between. Based on the fundamental structural design principles and specifications of ACI 318-19(22), the compression and flexural strength, and shear resistance of the walls can be checked to be compliant with the codes and specifications following the load and resistance factor design (LRFD) method. Specifically, the 0.187- in.-diameter steel wires in the pumpable J-Crib walls and 20-gauge steel panels in the HS stopping walls are integral parts of the walls and are considered to effectively confine the J-Crib or J-Seal materials. These steel elements play a significant role in reinforcing and improving the strength or support capacity of the stopping walls from a structural design perspective. Because of the high ductility of low-density J-Crib/J-Seal materials and steel elements, these walls are good at accommodating or absorbing the roof convergence (≥5% entry height), which cannot be matched by a traditional concrete block stopping wall (Figure 1). Based on the successful design and application of these stopping walls in different mines for improving roof stability and avoiding the air leakage, the authors have formulated the design methodology and verified independently by the finite element analysis (FEA) simulation technique. This design methodology combines the fundamental structural design principles with specific wall dimensions and material properties, facilitating mine engineers and government agencies to understand the in-depth working mechanism of these stopping walls.

Jul 1, 2023

By and Heather E. Lawson, Mark K. Larson, Gabriel Walton

In this study, we evaluated the effects of different shapes and distribution densities of mineral grains in coal on failure mechanics using the numerical software 3DEC. The main aim of this study was to identify possible failure mechanisms influenced by mineral habit and frequency in coal. Exploring differences in failure mechanics associated with the mineral grains helped to determine the role of mineral character as a possible contributor to characterize burst-prone coals. To achieve the goal of this study, a series of numerical specimens were prepared in the 3DEC model as follows: first, the 3DEC modeling in conjunction with the DFNs (Discrete Fracture Networks) technique was performed to explicitly generate the discontinuities (i.e., cleats and bedding planes) in the numerical specimens based on the results of laboratory analyses. Then, the different realizations of mineral grains were embedded in the 3DEC model to simulate an unconfined compressive strength (UCS) test to assess the influence of the mineralogical characteristics on the UCS.