Search Documents

By P. A. Plunkert, D. E. Morse, L. McCartan, J. F. Papp

The mineral sector is a fundamental part of the U.S. economy. It contributes to the real gross domestic product (GDP) at several levels — basic (mining), intermediate processing, manufacturing of finished goods and construction. The real GDP during 2004 increased by 4.4 percent. The nominal GDP was about $11.7 trillion. Housing starts were up by slightly more than 4 percent for the year. And the nation’s unemployment rate decreased to5.5 percent in 2004 from 6 percent in 2003. Interest rates continued to be low (prime rate was 5.25 percent at the end of 2004) but have risen gradually, following rising inflation.

Jan 1, 2005

By M. L. Harris

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) has developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five and three underground coal mines in MSHA District 2 (PA) and District 11 (AL), respectively. While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (% IC) determined by the CDEM agreed well with those obtained later by low temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

Jan 1, 2008

By Yves St-Amour, Vince Luongo

This paper will discuss one of the largest construction projects the City of Portland has undertaken. This phase of the Willamette River Combined Sewer Overflow (CSO)project consists of approximately 18,500 ft of tunnel in soft ground, requiring the construction of six deep shafts and jet grout ground improvement. The purpose of the project is to reduce volume of combined sewerage overflows from the drainage areas on the west side of the Willamette River. Bencor-Petrifond-Pacchiosi Joint Venture was awarded a contract to design and construct six deep circular shafts, jet grout ground improvement for three bridges and jet grout ground improvement break-in/outs for some shafts. Of the six shafts the Pumping Station Shaft was the deepest and largest, requiring a permanent ground support system with a deep jet grout ground water cut-off to 335-ft deep. The joint venture used state of the art methods and equipment to achieve its objectives and build the structures through some very difficult alluvial soils to great depths next to the Willamette River. The paper will provide a general discussion of the shaft construction and jet grout ground improvement installed for this phase of the project. It will also discuss some of the technical challenges encountered while effectively managing risk and costs, resulting in a successful project completed in a timely manner.

Jan 1, 2005

By Patricia Pride, Mike Robison, Jon Bergenthal, Wojciech Klecan

"The Lower and Middle River Des Peres (LMRDP) CSO Storage Tunnel is the largest single component of Metropolitan St. Louis Sewer District’s (MSD) CSO control system improvements planned to meet consent decree requirements for MSD’s Lemay Service Area. The 13.7-km (8.5-mile) long, deep, hard rock tunnel will have a finished diameter of 9.1 m (30 ft). Beginning at the Lemay Wastewater Treatment Plant (WWTP), the alignment follows the channelized River Des Peres to the outfall of the existing Forest Park tubes, as indicated in Fig. 1.The project includes three construction shafts, 34 intakes and a deep, cavern-style pump station located adjacent to the WWTP. The tunnel will be driven from the Defense Mapping shaft to the Macklind shaft. Another shaft is located near the midpoint at the tunnel in River Des Peres Park.The Forest Park intake, located at the upstream end of the tunnel just beyond the Macklind shaft, is a large, tangential vortex intake structure. With a peak flow rate of 170 m3/s (6,000 cfs), it will have a 6.1-m (20-ft) diameter dropshaft to transfer flow into the tunnel.The project includes another three large tangential vortex-flow intake structures with peak flow rates ranging from 28 to 44.5 m3/s (990 to 1,570 cfs). These large intakes are located at points where three large sewers (formerly creeks) enter the River Des Peres. Dropshaft diameters for these intakes range from 3 to 3.7 m (10 to 12 ft) in diameter. The 30 remaining intakes are smaller tangential vortex-style, with dropshafts in the range of 0.8 to 1.7 m (30 to 66 in.) in diameter.Each intake structure drops flow into a deaeration chamber constructed adjacent to the tunnel at tunnel depth. Intake tunnels transfer flow from the deaeration chambers to the main tunnel. Most of the intake tunnels are short. However, two are long. The Glaise Creek tunnel will extend 762 m (2,500 ft) from the main tunnel to the Alaska Park intake, while the Rock Creek tunnel will extend 823 m (2,700 ft) from the main tunnel to the Rock Creek intake. The dewatering pump station, located at the downstream end of the tunnel, will be built inside a large, horseshoe-shaped cavern with two access shafts. Excavation of the cavern and its access shafts will be performed by the tunnel contractor. Build-out of the dewatering pump station will be performed under separate contract."

Jun 1, 2019

By J. V. Ghelarducci, M. A. Sharpe, D. G. Chedgy

This article presents a novel design, called the Climax, High Capacity Processor (HCP), for pre-combustion cleaning of coal. This design is particularly suitable for the plant capacities of 400 ~ 660 TPH. The HCP is different from the conventional designs with an equivalent throughput in three major aspects: 1) the use of one large capacity HM cyclone to separate coarse and intermediate raw coal in a single circuit; 2) the elimination of the conventional secondary magnetics recovery system by use of the high efficiency Climax, magnetic separators; 3) the use of "single line" piping with a minimum requirement of ancillary devices. In comparison with conventional designs with similar capacity, the HCP plant costs much less in capital investment, operation and maintenance.

Feb 24, 1997

By Robert A. Cummings

Disintegration of the immediate shale roof in coal mines interferes with ventilation, production, and safety. The effect is seasonal and correlates with high levels of moisture in the intake ventilation air. Disintegration, though not completely understood, is caused by shale dilation and weakening upon exposure to atmospheric moisture. Fluctuating moisture conditions are particularly deleterious, and may be at least partially controlled by "tempering" the air before it is brought to the working places. Roof behavior was studied in an operating mine during a 12-month monitoring period. This approach can be used in developing criteria to reduce or prevent shale roof deterioration.

Jan 1, 1981

By J. S. Carman

As with the slogans of Madison Avenue, catch words or phrases frequently become topical. Much is heard these days of the confrontation between governments of developing countries and international mining capital. In actual fact, sadly there are too few cases of anything as positive as confrontation because such an action at least signifies a dialogue which may begin badly but end up fruitfully. Instead we have in general a climate of indifference and fear with the mining companies of note marking off most of the developing world as being unsafe for investment. There is an unreal air to this damaging impasse. The common sense and objectivity which are prerequisites of positive action are lost in a swirling cloud of mythology, embraced largely by governments. Let us examine some of the dangerous misconceptions.

Jan 1, 1977

By S. Lähteenmäki, P. Koivistoinen, J. Levanaho

Semi Autogenous Grinding (SAG) circuit is the most common grinding circuit to day. In Europe and South Africa fully autogenous (AG) circuits are also popular. SAG circuit has a lower capital cost and simple operation. SAG circuit requires the use of grinding balls, which increases operating costs and decreases availability. An AG circuit may produce a higher Net Present Value to the investment. The AG circuit is more complex to design and operate. However, operating experience from AG circuits illustrates that an AG circuit can be as trouble free as a SAG circuit with the benefit of lower operating cost.

Jan 1, 2001

By Erika Moonin, Jim Nickerson, Claudio Cimiotti, Roberto Bono

"In response to the severe drought on the Colorado River basin and in order to preserve existing water capacity to the Las Vegas Valley, the Southern Nevada Water Authority contracted a new deep-water intake (Intake No. 3) located in Lake Mead. The current project (Contract No. 070F-01-C1) includes 5 km (3 miles) of tunnel with very difficult geological conditions and a 200- m (650-ft) deep shaft and marine works. This paper will present the current status of the design-build contract being constructed by Vegas Tunnel Constructors and the challenges and problems faced and the innovative solutions developed to handle the difficult conditions encountered during tunneling with up to 15 bars of pressure.ProjectbackgroundThe Las Vegas Valley receives the majority of its water from Lake Mead, which is located approximately 30 km (20 miles) east of the Las Vegas, NV metropolitan area. Due to the severe drought that has hit the southwest region of the United States, the water level in Lake Mead has receded from its high water level of 372 m (1,221 ft) above mean sea level (amsl) to a low of 330 m (1,076 ft) amsl in June 2015. Should the lake level continue to fall, at elevation 320 m (1,050 ft) amsl, the current water intakes will not be able to draw enough water to meet the needs of the local area. The risk of losing water capacity has prompted the construction of a new deeper intake. Not only is the new Intake No. 3 situated at a lower elevation in the lake at 262 m (860 ft) amsl, the new Intake No. 3 is also located to draw better quality (Fig. 1).Project challengesThe project has had several difficult challenges to overcome:• The work consisted of a 1.2 kt (1,300 st) structure constructed on a barge and lowered 100 m (330 ft) into Lake Mead anchored with 9,200 m3 (12,200 cu yd) of tremie concrete.• The drill-and-blast starter tunnel was impacted by three inflow events, resulting in a one-year project delay.• One of the main challenges was selecting the tunnel boring machine (TBM) and excavating the tunnel with expected hydraulic head pressure of as much as 17 bar (16 bar was the highest pressure recorded during the drive), crossing faulted areas, low rock cover and the risk of tunnel instability due to direct connection with the lake.• Extensive pre-excavation grouting with a constant head pressure ranging from 12 bar to 15 bar.• Structural repair of the cutterhead in difficult hydrogeological conditions [water inflow of approx. 800 m3/hr (4,000 gpm)].• Complete repair of the cascade sealing system for the main bearing and two replacements of the pinion bearings.• The TBM approach to the intake structure."

Jan 1, 2015

By E. Bakhtavar

All parameters influencing the decision for selection of a suitable extraction method were first selected as the base of this study. Then these parameters were categorized in two main groups. The first group of the parameters includes ?geomechanical and inherent characteristics of the dimension stones? such as hardness, RQD, compressive strength, joints plane orientation and spacing, and water content. The second group was named ?technical and economical parameters associated with the investor?s objectives? like for example extraction capacity (production rate), blocks recovery, mechanization, capital investment and operational costs. Finally, the influences of all mentioned parameters on the selection of the most applicable extraction methods have been assessed and discussed.

Jan 1, 2012

By William H. Hansmire

The Modified Detroit River Outfall No. 2 (MOD DRO-2) will discharge treated wastewater to the Detroit River. Construction of a 6.4-m-diameter, 1.9-km-long tunnel was halted in 2003 by flooding during tunneling with an open face hard rock TBM. A new design for a higher rock tunnel, a ?Modified? design, was completed in 2007 and Notice to Proceed to the tunnel contractor was given in November 2008. Project duration is four years for completion of tunneling and start of outfall tunnel operation. This tunneling project has high groundwater pressure (5 bar), pervious limestone rock of up to 140 MPa (20,000 psi) strength, and hydrogen sulphide in the groundwater. The new tunnel will be connecting to access shafts and outfall diffuser riser shafts previously built for the now-abandoned tunnel. The new tunnel design construction contract, and initial planning to use a pressurized-face (slurry) hard rock TBM are presented.

By David W. Wisecarver

Kennecott Copper Corporation and the U. S. Bureau of Mines cooperated in a full-scale slope stability research project at the Kimbley Pit near Ely, Nevada. The west wall of the Kimbley Pit was mined from an over-all slope angle of 45° to an over-all slope angle of 57° and the pit was deepened nearly 50 feet. Mining was begun February 10, 1966, and completed October 30, 1966. Approximately 2.55 million tons of ore and waste were mined. The project was designed and carried out to learn more about the behavior of a pit wall as its slope angle is steepened and to obtain a possible insight into engineering parameters for use in design of future slopes. Data from this project are presented as obtained from (1) instruments installed in two adits for deformation and displacement measurements, (2) a subsidence network installed on the surface above the steepened wall, (3) pre- and post-mining observations of stress in rock, (4) sonic-velocity measurements, and (5) seismic and microseismic investigations. Changes occurred in measured quantities as the slope was steepened but stopped when mining was completed. Agreement was noted between the measured changes and predicted changes obtained from calculations using the finite element technique. Subsidence surveys and microseismic studies show the steepened pit wall to be stable.

Jan 1, 1968

By L. You

Theoretical and analytical analyses of three mitigative measures- plane fitting method, trenching, and tension cable led to the development of a total protection plan to eliminate or reduce damages to the residential structures subjected to surface movements caused by underground longwall mining. The protection plan was applied to twelve residential houses and two external garages. The success rate is overwhelming. This paper describes the methods employed for protection and results of those case studies.

Jan 1, 1986

By C. J. Roos

Ground engaging tools are used to prevent damage to the main components of earth-moving equipment. These tools consist of everything from shovel teeth to replaceable drill bits to dozer wear plates. The costs of these ?consumable? items are increasing with the costs of raw materials. This project developed a tool to be used by Newmont Mining Corporation to predict the consumption of excavator teeth. This paper presents the results of a Montana Tech research project in which an equation was developed to predict excavator teeth consumption based on production rates and rock properties.

Jan 1, 2009

By J. F. T. Agapito, G. P. Bratton

A 16 m by 4.7 m by 24.5 m (52 ft by 15.5 ft by 80.5 ft) underground ore bin was constructed at an 810 m (2660 ft) overburden depth in poor quality, faulted and altered intrusive rocks at Molycorp's block caving molybdenum mine. Geological engineering incorporated detailed structural mapping, rock quality classification, in-situ stress field determinations, numerical stress and failure analysis, and convergence monitoring. The ore bin was mined by conventional methods from the top down and utilized a bored raise for mucking. The initial ground support of rock bolts, lightweight steel sets, and reinforced concrete was later supplemented with an array of 6, 12 and 21 m tensioned, grouted rock bolts when wall closure was noted in the upper ore bin area. The supplementary support was optimized by computer analysis and monitoring.

Jan 1, 1985

By Vivek Priyadarshi, VIVEK KUMAR HIMANSHU, A. K. Vishwakarma, M. P. Roy, A. K. Mishra, RAVI SHANKAR

The nature and orientation of joints in rock strata affect the damage pattern under explosive loading. Most of the limestone deposits in India are found with severity of joints. Categorically, these joints may have variable orientations such as dipping out of the blast face, inside the face, horizontally or having strike parallel to the face. The damage pattern under the varying category of orientation will be different. Accordingly, a numerical model in Ansys-Explicit Dynamics was prepared to compare the damages of rock mass under different joint orientations. The physical nature of a joint reflects frictional and stiffness behaviour. Accordingly, the damages have been compared under bonded and frictional nature of joints. The output damage pattern from the model has been validated on the basis of blastability index proposed by Lilly. Different limestone mines in India show different nature of jointing in their rock strata. Accordingly, the blasting outputs from three different limestone mines, viz. Rawan limestone mine, Sagmania and Birhauli limestone mine and Injepalli limestone mine, have been compared along with their blast design parameters and the nature of joint. The comparative results show that the closely spaced horizontal joints support maximum in burden movement and rock fragmentation due to blast.

Nov 23, 2023

By N. Ahmed

The collection of hydrophobic particles in the froth phase in flotation has been studied. A continuous flotation cell was developed, in which the froth phase could be isolated from the pulp zone. Hematite particles, d80 = 87 µm, were floated in the pulp, using a conventional oleate collector, while glass spheres of similar diameter, d80 = 82 µm, were introduced in wash water added to the froth. Four samples of glass spheres, with contact angles between 0 and 82 degrees, were used. The results indicate that the efficiency of collection of the hydrophobic particles in the froth can be very high. The process is strongly influenced by the hydrophobicity of the particles and the surface area available for attachment in the froth. Recommendations for the flotation of particles in the froth phase are made, especially regarding the desirable hydrophobicity as reflected in the contact angle, the froth depth, the solids concentration in the feed to the froth, the air rate and the wash water rate.

Jan 1, 2001

Canadian mining giant Teck Resources Ltd. will be the exclusive supplier of the metals used in the production of the more than 1,000 medals to be awarded at the Vancouver 2010 Olympic and Paralympic Winter Games. Teck, the diversified resource company headquartered in Vancouver, B.C., is providing 2.05 kg (4.5 lbs) of gold, 1,950 kg (4,300 lbs) of silver and 903 kg (2,000 lbs) of copper sourced from its operations around the world. In addition to the raw materials mines, this year?s medals will make Olympic history as they will be the first to contain metals recovered from processing the circuit boards from end-of-life electronics (e-waste) that would have otherwise been destined for a landfill. After mining or production through a variety of smelting and recovery processes, each metal has been refined to enhance the metal purity.

Jan 1, 2010

By Robert Kimutis, Lihong Zhou, Mark Mazzella, Jim Addis

Due to the surge in shale gas production, a substantial number of unconventional shale gas wells have been drilled across U.S. coal reserves. Gas breaches resulting from damaged wells pose a considerable safety risk to miners. This paper investigates how a ventilation system can effectively manage breached gas through a network-based numerical model and laboratory-scaled physical model. Several hypothetical gas breach scenarios in a longwall area are simulated, exploring factors influencing gas mitigation. The study establishes correlations between breached gas inflow and gas concentration at critical locations. The findings in this study provide valuable insights for managing mine ventilation systems and enhancing coal miner safety.

Feb 1, 2025

By R. S. C. Rogers

The present study examines the use of two vs. one stage of hydrocyclones in a pilot scale ball mill circuit. The approach used for doing this is based on computer simulation with mathematical models that explicitly account for the grinding mill/classification system interaction. Parameters for the ball mill model are obtained using a short-lived radioactive tracer method in open circuit tests of the study mill. The hydrocyclone model, based on the size selectivity concept, is developed and validated in standalone testing of the study hydrocyclones. Simulation procedures are validated through actual tests of the closed circuit grinding configurations of interest. Results of the evaluation indicate that two stages of hydrocyclones in the study circuit would improve classification, increase productivity and lead to more closely sized circuit products when compared to the conventional one stage hydrocyclone circuit. A computer simulation approach for comparing these circuit configurations in larger scale grinding circuits is also suggested.

Jan 1, 1981