Search Documents

By M. A. Trevits

Mine seals are used in underground coal mines throughout the United States to isolate abandoned mining areas from the active mine workings. The objective of adding inert gas to a sealed mine area is to quickly reduce the oxygen concentration in the sealed area to a level that will not support combustion. In the US, this process is typically conducted from the ground surface and because surface-to-mine access is constrained by so many variables, it is very difficult to provide a source of inert gas to the place where it is needed underground. To alleviate this problem On Site Gas Systems, under a NIOSH contract, built a nitrogen (N2) generation plant that operates in the underground environment. The purpose of this work was to create a reliable in-mine mobile plant that would extract N2 gas from the mine atmosphere and use the gas to create and maintain a safe sealed mine area. The plant is based on a novel design using pressure swing adsorption technology and is sized to fit on a standard shield car or mine dolly for easy transport in and around an underground coal mine. The plant is capable of producing about 900 scf/min of N2 gas at ambient mine conditions. After an exhaustive series of laboratory tests, the plant was field tested at the NIOSH Safety Research Coal Mine (SRCM) where a portion of the mine was sealed and rendered inert. During the test, the movement of the injected gas was monitored at several underground points to observe the progress and extent of the inerting process. This paper describes the plant design and the results of the field test at the SRCM. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of NIOSH.

Jan 1, 2009

By Jr. Abel

Subsidence is controlled by a complex combination of mining and geologic factors. For example, a world-wide compilation of data shows that, as the percentage of shale in the overying rock mass decreases and the amount of sandstone increases, the angle of draw (and the area affected by subsidence) decreases. Limestone in the overburden appears to cause as much as a three-fold decrease in the angle of draw compared to a like amount of sandstone. Increased amounts of sandstone were accompanied by a greater surface subsidence relative to the mining height. The total thickness of overburden did not appear to influence the subsidence magnitude above super-critical panels. The greater the thickness extracted the smaller percentage of that thickness that shows up at the surface as subsidence. The greater the percent of the seam extracted, the greater the subsidence reaching the surface. The maximum subsidence above room and pillar panels is dependent on the pillar height and minimum width as well as the other factors listed.

Jan 1, 1980

By R. E. Thill

An ultrasonic, pulse-immersion apparatus and method are described for determining the effects of moisture on the dynamic elastic properties of rock. The method provides an alternative approach for assessing the moisture sensitivity of rocks. Ultrasonic wave velocities are continuously monitored in immersed rock samples as a function of water absorption and time up to saturation. Moisture effects on compressional wave velocity vary as a function of the type of rock and the time and amount of water absorption. Regression analyses are used to curve-fit plots of the data and to derive empirical expressions for compressional wave velocity as a function of water content for different categories of rock. Results indicate that compressional wave velocity can be used to predict both the moisture content and its effect on strength and deformational properties of rock. These results have potential for detecting or monitoring bad roof conditions in situations where the mine rock exhibits strength degradation with moisture absorption.

Jan 1, 1986

By Robert L. Marovelli

The major mining health and safety problems of concern to United States Government and private industry researchers in 1981 included the difficulty experienced by longwall operators in complying with the Federal 2 .0-mg/m3 respirable dust standard, the accident rate associated with falls of ground and materials handling hazards, and the upsurge in the incidence of disasters after the steady decline in recent years. Although the many mines and manufacturing companies involved in the research projects to be described are not specifically identified, it is important to note their significant involvement. This is not by way of acknowledgement, but rather to establish that these projects, using mostly Federal funds, represent close cooperation between the U.S. Government and the mining industry. The ongoing work to be described on the development of critical longwall dust control technology is a classic example of Government-industry participation through the phases of problem identification, planning, cost-sharing, and implement at ion.

Jan 1, 1982

By P. K. Parhi

The extraction of nickel has been carried out by the hollow fiber membrane technique using D2EHPA as the mobile carrier from the manganese nodule leach liquor after separation of Cu(II), Zn(II) and Co(II). The experiments were designed according to central composite design (CCD), which is a response surface methodology. The process parameters used for the experimental design were: pH, concentration of D2EHPA in the membrane phase, flow rate and H2SO4 concentration in the strip solution. Based on the analysis of variance, a reduced quadratic model was found to best fit the experimental data. The process parameters were optimized to maximize the nickel flux and the optimized conditions were flow rate: 630 mL/min; pH: 6.37; D2EHPA: 1.15 mol/L (1,150 mol/m3) and H2SO4: 2.39% (430.2 mol/m3), for a maximum nickel flux of 7.08 x 10-5 mol/m2.s, which was in good agreement with the actual Ni flux of 6.99 x 10-5 mol/m2.s.

By E. Knell

COM Energy, Inc., a subsidiary of Occidental Petroleum Corporation, has constructed a 1.6 million hectoliter-per-year COM plant in Jacksonville, Florida. COM will be distributed to customers in the region as a substitute for fuel oil presently burned in boilers and kilns. As the market for COM grows, COM Energy, Inc. expects to build additional units both in this country and overseas. This paper addresses the overall status and technical aspects of the project, focusing on the facilities for COM production and utilization.

Jan 1, 1982

By G. T. Lineberry

Horsepower requirement is recognized as a most important equipment characteristic. Other critical equipment characteristics will be isolated and analyzed by traditional operations research techniques, using off-highway trucks as an archetype. A computer search technique has been developed, employing various production and cost analyses. With this model, the optimum combination of horsepower, capacity, and velocity can be found, minimizing handling cost per ton. An example of the program's use and interpretation of its results will conclude the paper.

Jan 1, 1984

By Chunbao Sun, Qi Liu, Chao Wang

Entrainment is a process by which fine and ultrafine particles are transferred to the flotation froth from the top of the flotation pulp, and eventually discharge to the concentrate product, evenwhen they are not attached to gas bubbles. Therefore, entrainment can be considered as a two-step process, one at the upper layer of the pulp to the flotation froth, and the other from froth to the concentrate. Entrainment is inevitable for both hydrophobic and hydrophilic minerals and is one of the significant factors affecting concentrate grade. This paper provides a comprehensive review of the entrainment mechanisms and entrainment models, as well as a summary of the main factors affecting entrainment and the techniques thatmay be used to lower or eliminate entrainment. Based on the review, we point out that selective aggregation of fine and ultrafine gangue minerals using appropriate process aids (polymeric depressants, inorganic salts, etc.) to increase their particle sizes appears to be a convenient and economical method. Directions of further research along this line are discussed.

Aug 31, 2020

By Peter Kreisman

This paper and four other papers on the MEQB Regional Copper-Nickel Study, presented today at the 1980 SME-AIME Fall Meeting are based on four years of extensive inter-disciplinary research and impact analysis supported largely by the Legislative Commission on Minnesota Resources. This study produced over 180 technical reports, the results of which are summarized in an Executive Summary available from the Minnesota State Planning Agency, St. Paul, Minnesota. Those wishing to examine the many scientific, engineering, environmental, social or economic issues addressed by the study are encouraged to obtain a copy of the executive summary. The executive summary includes a bibliography of all technical reports produced by the Regional Copper-Nickel Study and describes the five-volume, 26 chapter Regional Copper-Nickel Study Report.

Jan 1, 1980

By Paul D. Tomlingson

There are huge benefits for mining operations that have a well-defined maintenance program that is understood and followed across the total operation. But for operations lacking a quality maintenance program, there is equal assurance that nearly every major maintenance problem can be traced to this omission. Few problems will be permanently corrected until such a program is implemented. Definition The maintenance program re-quires the interaction of all mine departments. Initially, the production department will request work and the maintenance department will identify work, principally through preventive maintenance inspection and testing efforts. Maintenance will then classify the new work to determine the best way to respond. Maintenance will plan selected major jobs to enable its crews to carry them out more effectively. Maintenance will schedule the planned work with operations. Supervisors will assign all types of work to their crews then, control the work through effective supervision. As work is completed, maintenance will measure the work using an accurate information system. Next, it will assess overall accomplishments against goals such as performance standards or budgets. In addition, the pro-gram would prescribe a means to evaluate every aspect of the operation as it affects maintenance so that necessary improvements or changes can be identified, prioritized and acted on. Such evaluations should be part of a mine-wide continuous improvement effort. A well-defined maintenance program is one of the best investments a mining operation can make to assure its profitability. Educating the total operation on the pro-gram assures long-term dividends from the investment.

Jan 1, 2008

By S. Watkins, D. Apel, B. Gray, R. Moss

Currently, there are several techniques and technologies available which are used by mining industry in its attempts to remotely monitor the ground movements both at surface and underground mines. The currently available remote distance meters and distance change monitors mainly use phase change and time-of-flight techniques. The described monitor uses triangulation technique to track position of an optical spot projection and then image processing to measure mine wall movements. The system can be easily automated and poses no obstruction to mine traffic. The position of an off-normal laser spot will shift as the target wall moves. The described ground movement monitoring system has potential for superior accuracy and target monitoring can be made through air (gaseous) or other transparent media. The theoretical accuracy and range of this system depends solely on the resolution and focal length of the camera being used. The remote capabilities of the system make it uniquely suited to applications where monitoring is required in high-traffic, inaccessible, or unstable and dangerous areas of a mine.

Jan 1, 2007

By I. Nimmo

Since the beginning of Aluminum mining and refining the industry has lived with distributed control rooms and suffered from many behavioral problems common with this design. When Human Factor/Ergonomic design is introduced to a Western Australian installation a common centralized control room realized many improvements including economic payback. Communications issues were resolved, better coordination of materials, improved situation awareness during startups, abnormal operations and an opportunity to make improvements during normal operations characterize the changes at the Worsley Refinery. This presentation will review the reasons for the change. Since the beginning of Aluminum mining and refining the industry has lived with distributed control rooms and suffered from many behavioral problems common with this design. When Human Factor/Ergonomic design is introduced to a Western Australian installation a common centralized control room realized many improvements including economic payback. This presentation will review the reasons for the change, what changed and the process of changing the culture from reactive to predictive and what difference that has made.

Jan 1, 2011

By Jon Ike Isaacson, Michael Miller, Jarek Trela

Despite reef structures being relatively common in carbonate rocks around the world, tunneling experience in reefs is extremely rare. Impacts and risks associated with reef tunneling through these geologic features were also relatively unknown. A new reef was encountered during construction of the Lower Pogues Run Tunnel in Indianapolis, exposed over 5,000 linear feet along the alignment, resulting in adverse impacts on construction. Analysis of investigation data and construction from this encounter provide insight into the identification and characterization of reefs along tunnel alignments as well as the potential impacts on construction for future tunneling within reef structures.

Jun 23, 2024

By William W. Edgerton

The California Department of Transportation (Caltrans), the Contra Costa Transportation Authority (CCTA), and the Alameda County Congestion Management Agency (Alameda CMA) are involved in a unique partnership on the planning and design of the fourth bore of the Caldecott Tunnel, located on State Route 24 in Alameda and Contra Costa counties. The project will add a two-lane bore north of the existing three bores. The project will alleviate traffic congestion in the non-peak direction. This paper provides background on the existing facility, summarizes the need for the new fourth bore, describes the proposed improvements, sets forth the approach for project delivery, and lists some of the challenges that are expected during construction.

Jan 1, 2008

By R. D. Lawrence

Suggestions have been made that the appraisal of mining assets using discounted cash flow techniques should be based solely on proven and probable reserves in reliance upon the widespread international recognition of uniform resource definitions. Following a review of general accepted valuation principles, a survey of the literature and, most importantly, a review of real transactions in the open market, it is clear that valuators should not be constrained by the growing acceptance of modern mineral resource codes. On the contrary, valuation practitioners should be encouraged to examine all classes of mineralization and, after making due allowance for risk, to utilize all mineral resources as a basis for determining fair market value.

Jan 1, 2000

By R. R. Rollins

Field data combined with theoretical derivations were used to design a surface mining operation using explosive casting. Calculated casting results varied from 44 to 65% depending on bench height. This model was then applied to field tests at an eastern, contour, coal stripping operation. Results from five experimental casting shots are summarized and compared to conventional mining methods. The overburden material removed by casting ranged from 35 to 65% with an average of 50%. Fragmentation was improved and it was demonstrated that this procedure is economically attractive with a resultant cost savings of $.59/m3 or $5.93/t of clean coal.

Jan 1, 1987

By Richard A. Thomas, Liming Yuan, James H. Rowland III, DAVOOD BAHRAMI

To reduce the number of injuries resulting from fires on mobile, diesel-powered mine equipment, it is crucial to promptly suppress a fire once it is detected. The focus of this research was to determine the effectiveness of fire suppression agents. Large-scale tests were conducted using five different fire suppression systems based on: dry chemical, wet chemical, dual agent (dry and wet chemical), carbon dioxide, and water mist. Suppression nozzles were placed around the diesel engine where diesel fuel, engine motor oil, and hydraulic circulating oil spray fires were ignited. The results of this study can help mining companies and manufacturers by providing scientifically based data on the capabilities of the different fire suppression systems.

Feb 1, 2024

By J. A. Mielczarski

Surface properties of minerals could be modified selectively and very specifically by adsorption -desorption (dissolution) processes. This requires a monitoring and control of the outermost surface layer at a molecular and atomic level. The nature and structure of self-assembled submonolayers and monolayers at the interface of minerals were studied by infrared reflection spectroscopy. The external reflection spectra of the adsorbed monolayers on any type of minerals: transparent, opaque or non-transparent, recorded at different angles of incidence and for two polarizations are an excellent source of information about the nature and surface distribution of the adsorbed species. The developed method allows to obtain detailed information at a molecular level about the adsorbed surface species. By combination of the simulated and experimental data, the qualitative description of the adsorbed species as well as quantitative evaluation of orientation and the thickness of the adsorption layers were obtained. This fundamental knowledge allows to determine the mechanisms of surface phenomena which govern selective separations. Examples of different surfactant - mineral systems and industrial applications will be discussed.

Jan 1, 2000

By Chamila Jinendra Nanayakkara, Nimila Dushyantha, Amila Sandaruwan Ratnayake, Gayithri Niluka Kuruppu

Rare earth elements (REEs) are key ingredients in many advanced materials used in energy, military, transportation, and communication applications. However, the prevailing geopolitical dynamics and the rising demand for REEs have rendered the reliance on primary REE resources susceptible to future supply disruptions, posing a substantial risk to the availability of these elements for numerous applications. Therefore, it is imperative to undertake substantial initiatives in the extraction of REEs from secondary sources on a large scale to ensure the resilience of the supply chain. Permanent magnets, lighting phosphors, and nickel-metal hydride (NiMH) batteries are among the secondary sources with high potential for sustainable REE extraction. This review assesses the extraction potential of REEs from the aforementioned three secondary sources and their leaching kinetics and thermodynamics aspects. More importantly, state-of-the-art different existing kinetic models employed in rare earth (RE) leaching were well discussed for a better understanding of the REE leaching reactions. Furthermore, the optimized leaching parameters related to this kinetics were described, and various RE recovery methods were comprehensively summarized. These processes facilitate to managing one of the fastest-growing solid waste streams by minimizing environmental impacts and producing critical metals, including REEs via circular economy approaches. The recovery of REEs from secondary sources aligns with numerous United Nations Sustainable Development Goals (SDGs), particularly in the renewable energy sector for climate change mitigation. Consequently, this trash-to-treasure urban mining concept to transforming e-waste into a valuable resource for REE recovery emerges as a pivotal element within the REE industry.

Dec 28, 2023

By Jiayao Wang, Jian Chen, Leiting Shen, Hongyang Wang, Zeping Cao, Ziru Wang

Large amounts of by-products, including coal gangue, circulating fluidized bed (CFB) slag, and coal fly ash (CFA), are generated during mining, washing and burning of high alumina coal (HAC). The stockpile of these by-products of HAC will cause the pollution of air, water and soil. Meanwhile, the unbalanced regional distribution of bauxite and alumina production has been a critical challenge for the sustainability of world alumina refineries, especially for China. Therefore, economical extraction of alumina from by-products of HAC not only resolves the environmental pollution problems caused by stockpile but also decreases the dependence degree of import bauxite in China. Considering the fact that powder alumina can only be produced by alkali methods, the alkali extraction of alumina from by-products of HAC is summarized in this paper. Based on the formation process of by-products of HAC, the principle, research status, and problem of existing methods were analyzed and discussed, as well as the forecast of research trend. The analyses indicate that simplex recovery of alumina from byproducts of HAC generates large amounts of leaching residue (red mud) with difficulty for disposing, while comprehensive extraction of alumina and silica meets the research trend for clean and high-value utilization.

Aug 25, 2023