Search Documents

By Zhiguo Chang, QINGXIANG CAI, Ebelia Manda, IZHAR MITHAL JISKANI, XIANG LU, Wei Zhou, Saleem Raza Chalgri

The concept of mine safety is highlighted in the literature of sustainable mining but not extensively discussed. This study analyzes various aspects of underground and surface mine safety and emphasizes its importance in the context of sustainable mining. More specifically, this research attempts to find the relationship between mine hazards and demographic characteristics, examine and compare the perceptual difference among miners, and determine the impact of mine hazards on workplace safety and safety climate. Descriptive analysis, chi-square test, independent samples t test, and linear regression modeling were conducted to achieve study objectives. Results confirmed that mine hazards were significantly associated with age and experience. Miners perceived lower levels of management safety practices, followed by supervisor safety, coworker safety, and job safety. The analysis showed that underground miners reported lower safety scores than surface miners. There was a statistically significant difference between miners’ perception of safety climate (p < 0.05). The results showed that the higher prevalence of mine hazards predicts poor workplace safety and a low safety climate. The regression models revealed that mine hazards have a significant effect on workplace safety (p < 0.05) and safety climate (p < 0.05). In conclusion, the distinctive model of mine safety presented here contributes to the monitoring and design of comprehensive safety interventions and helps to better understand how certain factors interact on multiple levels to influence the overall safety of the industry. In this study, some suggestions are put forward to provide directions to develop a sustainable mine safety system.

Mar 27, 2020

By K. Norrena

Grade control in open pit mining requires the specification of dig limits that account for mineral grades, economic costs, and selectivity of mining equipment. Visual identification of ore rock types is ideal, but this is not always possible in lower grade disseminated deposits where ore/waste contacts are not visually discernible. In this case, conventional grade control practice consists of a two-step procedure (1) create a map of mineral grades at some selective mining unit scale, and (2) determine practical ore-waste boundaries or dig limits on the basis of the gridded block grades or assay information. This procedure is laborious, depends on a subjective assessment of where the boundary should be, and may be economically sub-optimal. We pose the determination of dig limits as an optimization problem and solve that problem with the technique of simulated annealing. Simulated annealing has the unique advantage of being able to combine multiple non-linear constraints into a single objective function. We use maximum profitability and the ability of the equipment to mine the proposed dig limits as constraints in the determination of optimal dig limits. We require a map of expected profit for eah block. Geostatistical techniques are recommended, for mapping expected profit but not necessary. Geostatistics will provide a quantification of the uncertainty in the grades within rock types using all available blasthole samples and exploration drilling. Some variant of L-optimal estimation or kriging can be used to determine the block-by-block classification that is economically optimum. We also need the expected profit for each block. It is unrealistic to assume free selection, that is, each block cannot be extracted independently of its neighbors. The optimal balance of &apos;&apos;accepting dilution&apos;&apos; and &apos;&apos;wasting ore&apos;&apos; is achieved to maximize profit subject to equipment constraints.

Jan 1, 2001

By Qingwen Shi, Brijes Mishra

The abstract discusses the use of numerical simulations to investigate roof fall in underground mines. It highlights the advantages of the discrete element method (DEM) in simulating large strain problems and fracturing processes, while acknowledging its computational limitations for large-scale problems. The study presents a 3D numerical model coupling the finite difference method (FDM) and DEM to simulate laminated roof failure in a coal mine. The model represents the laminated roof with bonded particles and discontinuities, while the surrounding rock is represented by continuum zones. The research analyzes the fracturing of the laminated roof as the entry advances, demonstrating the coupled method's ability to reproduce laminated roof failure.

Mar 17, 2022

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. The roof bolts tested are also used to identify the possible corrosion mechanisms that influenced the bolts’ performance over time. Initially, the most commonly used bolt material in the USA, the ASTM A615 grade 60 steel roof bolts, was tested with and without stresses in a simulated underground coal mining environment for approximately 6 months, and the results are discussed. Localized corrosion forms such as crevice and pitting were mainly observed after testing. The stressed and unstressed roof bolts with and without threads that were tested in alkaline coal mine corrosive environment for 6 months passed their load-bearing capacity as per ASTM F432 test standards. From the results, it is concluded that this test protocol could be applicable to test the material performance of different roof bolt metallurgies and coatings with desired modifications to the proposed methodology for the specific underground mine environment. This paper mainly discusses the test system and protocol and shortcomings of the system and makes recommendations based on the observations and results.

By T. J. Haddon

For the mining industry in general and gold mining in particular the past few years have been difficult. Economic conditions coupled with growing regulatory restrictions have led to increasingly important reasons for managing assets wisely. From a public company perspective this makes sense because it ultimately provides for an increase in shareholder wealth and that&apos;s what we&apos;re in business to do. Regardless of whether a company is public or not, assets must be managed effectively to remain a player in today&apos;s competitive environment. So, as the CEO of a gold mining company, how do we manage our assets to ensure that we are satisfying our obligations to our customer --the Amax: Gold shareholder? Let me tell you. As I said earlier, the gold industry has been under siege. We have just completed our third year of average prices below $400 per ounce. When you add finding and/ or acquisition costs and development costs to operating costs, there isn&apos;t much of a profit margin left. What this environment provides, however, is opportunities for growth. In the gold business, you either grow or you die. Today, most North American gold producers have at most a 10 year mine life. We are all scrambling to add reserves so we don&apos;t become extinct. As prices remain low, opportunities for increasing diminishing reserves abound. This is the time for the opportunistic company to take advantages of market conditions and that&apos;s precisely what we, at Amax: Gold, have done!

Jan 1, 1992

By J. P. Kennedy, O. A. Bascur

Large metallurgical complexes have more data than a small city and these data change as internal and external conditions evolve. Staffing turnover hinders experienced-based decisions especially with simple tools like spreadsheets. Lack of current information can contribute to decisions that result in significant deterioration in the quality of operation. Timely, unified information from sophisticated analyses presented to the broadest possible reach will improve operation. The major innovation is the addition of the web browser to the suite of software people will use with no training – the other two are spreadsheets and graphical presentations – and the consistent organization and transformation of the real time data to support broad access. This paper describes the data transformations and presentation methods necessary for a Web view, especially the special needs of real time data and analysis required for active operations decision-making. Many people inside and outside the complex, not just operators, need timely information that is abstracted, aggregated, organized and unified. Unification and aggregation of real time data presented via the Web opens a new paradigm for collaboration. The analysis tools are as important as the data. These rule-based tools add significantly to the operations database in the form of results stored for viewing with plant data. Mining and metallurgical plants already use many sophisticated analysis tools such as predictive maintenance policies based on statistical analysis vibration analysis, and oil and lube analysis for critical equipment. These add real time events, similar to an alarm package, and unified production information to the operational database. Simple models are used on line to create key indices that provide a real time indication of performance. Key indices include metrics for losses due to plant availability, performance efficiency, and overall process equipment effectiveness. These additional data in the operations database are used for early fault detection, increased production, better quality, higher availability of equipment and faster detection of process bottlenecks. An important feature is the ability for people to create their own key indices and store the results for use by anyone in the plant historian, but accessible by a browser. Keywords: plant information, principle components analysis, data reconciliation, gross error estimation, Internet, Word Wide Web

Jan 1, 2002

By Jie Long, Zijie Liu, Pu Liu, Bo Li, Menghua Li, Qiang Wu

During coal mine operations, roadways may be located close to faults. When designing these roadways, it is important to determine the width of the rock mass between a roadway and a fault area to prevent water inrush. In this paper, the Xintian Coal Mine in the northern Guizhou Province of China is selected as a typical case. Through numerical simulation based on orthogonal tests, range analysis, and multiple linear regression (MLR) analysis, the process of water inrush from faults in excavation roadways is studied. The results show that the influencing factors of the safe width of a rock mass preventing water inrush (RMPWI) can be ranked according to the degree of influence from large to small as follows: the hydraulic pressure of the fault, the surrounding rock grade, the overburden depth of the roadway, the cross-section height, and the dip angle of the fault. Among them, the dip angle of the fault, the cross-section height, and the surrounding rock grade are negatively correlated with the safe width, while hydraulic pressure of fault and overburden depth of roadway are positively correlated with safety width. The predicted value for the safe width based on MLR is greater than the measured value of the width of the RMPWI when water inrush occurs, but less than the calculated value based on the empirical formula in the standard, which proves the accuracy and practicability of the prediction method. This research provides a certain basis and reference for the prevention and control of water inrushes in mines.

Jul 5, 2023

By W. L. Jacobsen, T. L. Dyer

Cortez Gold Mines completed a feasibility study for a new openpit gold mine in north central Nevada. The production schedule calls for a peak in material movement. This schedule is based on current operational efficiencies and equipment parameters observed at the company’s existing openpit operation. To mitigate risks of over/under predicting production, simulation modeling was used to validate the loading and haulage requirements during the peak production period. The advantage of simulation is the ability to provide a realistic model of a mining operation based on scheduled and unscheduled random events during the period under analysis.

Jan 1, 2007

By Jessica M. Wempen, William G. Pariseau, Dallan J. Coons, Michael K. McCarter, Erik C. Westman

The abstract discusses the importance of proper pillar sizing in underground mining for safety and efficiency. It highlights the use of theoretical models, geotechnical measurements, and numerical modeling in predicting pillar behavior. The research focuses on using seismic tomography to image stress changes in a yield pillar at a longwall mine as the longwall face approaches. The study aims to compare the stress distribution imaged using tomography with theoretical models, geotechnical measurements, and numerical models.

Mar 18, 2022

By D. R. Spears

As part of its mission to develop technology to assure a continuing supply of minerals, the US Bureau of Mines has investigated the flocculation of a Stillwater, MT, chromite ore. The ore was flocculated at different solids contents and at different stirring speeds to determine the importance and effect of hydrodynamic factors. In acidic and basic pH, the chromite ore was flocculated with high molecular weight polyacrylamides differing in the degree of hydrolysis. Polyacrylamides were found to bind to chromite ore particles through hydrogen bonding. The anionicity of the polymer and the pH affected the degree of polymer-particle interaction, which in turn affected polymer conformation at the surface. A polymer conformation with many loops and tails was used to explain high flocculation efficiency. It was found that such a conformation could compensate for poor hydrodynamic conditions.

Jan 1, 1992

By SUHAINA ISMAIL, NORLIA BAHARUN, SHAIK ABDUL RAHMAN, WAN NUR SYAFIQAH ANUAR, MOHAMMAD REZAEI ARDANI

Refractory gold ore contains sulfide minerals like pyrite, chalcopyrite and sphalerite that are difficult to be directly leached by cyanidation or by lixiviants such as thiourea and halides. In such cases, it is necessary to perform oxidative pretreatment of the ore to oxidize the sulfide matrix, and gold particles can be exposed to the solution during the leaching process [1]. In recent years, hypochlorite and chloride solutions have been introduced as alternative materials for hydrometallurgical methods of gold extraction instead of cyanide solution [2]. A previous study by Hasab et al. [3] reported that the gold dissolution rate in hypochlorite solution was higher than in the cyanidation process, due to the presence of hypochlorous acid (HOCl) as a strong oxidizing agent. In a hypochlorite leaching system, the change in pH can influence the presence of oxidant species in the solution: the hypochlorite ion (OCl−) is stable in pH greater than 7.5, HOCl can be found in pH between 4.0 and 7.5, and aqueous chlorine (Cl2 (aq)) is the predominant oxidant when pH is below 4.0. As HOCl is the most effective oxidizing agent for gold extraction, pH should be maintained in the range of HOCl stability [4].

By Fred D. Fox

Introduction Abandoned mill tailings deposits can be found throughout the northern Black Hills of South Dakota, indicative of mining activities that originated during the great gold rush days of 1875. The Refuse Act of 1899 attempted to regulate the deposit of debris from mines and stamp works. But, in most cases, huge volumes of mine and milling wastes were disposed of in ways no longer considered environmentally acceptable. Restoration of gold mill tailings deposits is a relatively new practice to the Black Hills area. This discussion will present an overview of the environmental setting, environmental problems associated with past tailings disposal practices, practices being implemented to solve these problems, and prospects related to present the future tailings disposal practices. Environmental Setting An understanding of climatic characteristics, geology, surface and ground water hydrology conditions, and the physical and chemical characteristics of selected mill tailings deposits will aid in understanding environmental problems associated with tailings disposal and restoration. Climate The Black Hills region is in the middle latitudes, which have a

Jan 11, 1984

By J. C. Motz

With ore grades continually decreasing and finer mill feed requirements, it becomes increasingly important to have the capability to handle the larger tonnages economically. With the 10 ft. Standard capable of reducing 1,633 metric tons per hour (1,800 short tons per hour) to 80 percent passing 50 MM (2 inches) and the 10 ft. Short Head following to produce a mill feed of all minus 12 MM (1/2 inch) at a rate of 608 metric tons per hour (670 short tons per hour), we feel significant savings will be realized in installation and operating costs. The largest concentration of cost in the secondary and tertiary crushing stations is the building itself that houses the process equipment. An example of the savings to be attained can be seen from an examination of a 40,820 metric ton (45,000 short ton) per day crushing plant. A total of nine 7 ft. Symons Cone crushers is used to generate 12 MM (1/2 inch) ball mill feed. The average center distance between units is 6.1 M (20 feet) and allowing a 6.1 M (20 feet) nominal distance from the centerline to the wails, the building becomes 61 M (200 feet) long. For this production rate, four 10 ft. Symons Cone crushers would be required. With the 10 ft. crushing plant requiring a center distance spacing of 7.6 M (25 feet), the building length totals approximately 38 M (125 feet). Construction costs vary depending on location, but a reduction in building length from 61 M (200 feet) to 38 M (125 feet) will result in estimated savings of between $2,500,000 and S4,000,000. While the 10 ft. Symons Cone has been involved in a number of feasibility studies for some time, the Process Machinery Division of Rexnord commenced detail design work on the 10 ft. Cone crusher in 1972. For comparison purposes, the 10 ft. and 7 ft. capacities are given in Table 1.

Jan 1, 1978

By Derek Brennan, Donald Brennan

"The existing Rondout West Branch Tunnel (RWBT) is part of the Delaware Aqueduct which has been in service since 1944 and accounts for more than 50 percent of New York City’s water supply. In early 2015, the New York City Department of Environmental Protection contracted Kiewit-Shea Constructors, AJV (KSC) to construct the Rondout West Branch Bypass Tunnel project (Rondout) in order to mitigate the leakage of 132 million L/ day (35 million gpd) of water from two areas of the existing tunnel; the Roseton and Wawarsing areas.The scope of the Bypass Tunnel 2 project is separated into two distinct phases. Phase 1 consists of completing the shaft sinking to a depth of approximately 274 m (900 ft) at shaft 5B, 213 m (700 ft) at shaft 6B and the excavation of approximately 3,850 m (12,500 linear ft) of tunnel at a diameter of 6.6 m (21 ft 7 in). This phase also includes the installation of 2,804 m (9,200 linear ft) of 4.8 m (16 ft) diameter steel interliner pipe through the new bypass tunnel with cast-in–place concrete liner for a finished diameter of 4.2 m (14 ft). Access chambers at the top of shafts 5B and 6B will be constructed for access and housing of the mechanical and electrical equipment for supporting pumps and valves.Included in phase 2 is the additional excavation from shafts 5B and 6B to the RWBT, and the drainage tunnel to remove ground water infiltration from RWBT. This work will be completed during a scheduled shutdown of the RWBT and will include approximately 31 m (100 ft) of excavation of the two connection tunnels. Additionally, construction of the permanent plugs within the RWBT will be undertaken. Figure 2 shows the layout of the work.Access to the work through the deep shaft at site 5B was critical to the success of the project. The hoisting system needed to be multi-functional to handle the different types of construction from drill and shoot of the shaft, starter and tail tunnel, the assembly of the tunnel boring machine (TBM), the excavation of the TBM tunnel including the supply of the precast segmental liner, the grouting operations, the installation of the steel interliner pipe and the cast-in-place concrete as well as ingress and egress of personnel. The production of the TBM operations was critical to the schedule of the project. This required a quick cycle for muck haulage and supply of the precast segmental liner in order to keep pace with the excavation time of the TBM. For TBM assembly, components were limited to a maximum weight of 104 t (115 st) for a single lift. Various cranes were analyzed for hoisting, however, none would meet all of the citeria. Therefore, the project team selected a specialized hoisting system designed in house in conjunction with Timberland Equipment Ltd. that consisted of a total of 14 separate hoists and winches with a total of more than 2,833 kW (3,800 hp)."

Mar 1, 2019

By R. Leithner

The need/wish to sequestrate CO2is based on the assumption of the International Panel of Climate Change (IPCC), that CO2 maybe the major driver in climatic changes, i.e. especially the anthropogenic CO2emissions due to the combustion of fossil fuels like coal, oil and natural gas will increase the atmospheric CO2-content, which will lead to higher temperatures in the atmosphere. The 0.03% CO2in the atmosphere have a 22% share of the natural greenhouse gas effect of 33 K necessary for life on earth. The main share of 62% has the water vapour in the atmosphere. Only if one concentrates on the greenhouse gas effect of the gases beside water vapour, CO2 becomes most important with 58% influence. In addition there are other influences on the climate like: • Eccentricity of earth’s orbit, precession of orbital plane, obliquity and precession of earth’s rotation axis (Milankovitch’s theory) • Sunspots and magnetic field of the sun • Changing streams in the ocean • Volcanic activities • Distribution of continents on the surface of the earth • Impact of meteorites • Change of insulation by interplanetary dust [Muller, R.A. 2000] etc. To answer the question, if the CO2-content in the atmosphere has an important or exclusive influence on the earth atmospheric mean surface temperature, one should look into history. Figure 1shows the mean temperature of the atmosphere and the atmospheric CO2-content time histories 1 billion years back; no correlation can be found between them. Nevertheless a lot of countries have committed themselves to reduce their CO2-emissions.

Jan 1, 2004

By W. G. Pariseau

This contribution focuses on the role of stress analysis for mine planning and the selection of suitable computer programs for the task with special emphasis on coal mine pillars. In this regard, barrier pillars that defend a set of five main entries at the Crandall Canyon coal mine in central Utah were formed during extensive longwall mining north and south of these main entries. Numerical analysis for ground control guided the mine planning and permitting. Retreat mining of pillars led to disastrous events August 6 and 16, 2007, with the loss of nine lives. A most difficult lesson taught by the Crandall Canyon tragedy is the need for education in the selection and use of computer programs for pillar design. Much of this contribution is taken from a report prepared for the Mine Safety and Health Administration (Gates, et al, 2008). Details appear in Appendix Q of the report (Pariseau, 2008). The Crandall Canyon mine is about 16 miles west of Huntington, Utah, in the Wasatch Plateau coal field. Geology of the Wasatch Plateau is described by Doelling (1972) as gently dipping Cretaceous sandstones, mudstones, coal seams, and shales. Joint systems are present in strata above and below coal seams where cleat systems are present as described by Hucka (1991). Several major fault systems transect the field and form grabens with 450- 760 m of drop. One such structure is Joes Valley fault that crosses the Crandall Canyon mine. Mines in the Wasatch Plateau are generally developed from outcrops in steep canyon walls. Overburden increases rapidly as mining progresses into the plateau; mining depth varies with topography between 450 and 600 m in the region of interest. A stratigraphic column derived from a borehole into the mine is shown in Figure 1. There are 11 layers in the column.

Jan 1, 2011

By C. Demir, M. S. Celik, I. Gülgonul

Na-feldspar (albite) and K-feldspar (microcline or orthoclase) are major feldspar minerals with identical crystal structures and physicochemical properties. Flotation appears to be a unique method of separating these minerals. Fundamental studies on amine/feldspar system in the presence of monovalent salts showed that separation of these feldspar minerals by flotation is possible at certain concentration of monovalent salts in HF medium and natural pH. A comparison between natural pH and HF medium indicates that the latter provides a better selectivity at the expense of higher collector requirement. A general mechanism for both systems involving an ion exchange between the uncommon ions and adsorption of the common ions is proposed to be responsible for creating differences in the charge of albite and microcline unto which amine adsorbs.

Jan 1, 2002

By K. E. Yassin, A. Yehia, M. Amar

Phosphate fines (size ≤ 45 μm), from the Red Sea Region, Egypt, were subjected to beneficiation process to recover the phosphorite grains from such fines. The sample is characterized by low P2O5 content (18.78%) associated with gangue minerals such as silica (22.77% SiO2) and carbonate (2.01% MgO) indicating its low grade. Phosphate pre-concentrate was prepared by gravity separation, using Falcon, where 63.37% of the phosphate, with 24.94% P2O5, 1.46% MgO, and 10.54% SiO2, was firstly recovered reducing the mass flow to the subsequent beneficiation process. However, the gravity tailing was the feed for the reverse phosphate flotation using bench scale column flotation where oleic acid was used as a carbonate gangue collector and amylase enzyme as a phosphate depressant. Under the appropriate flotation conditions (0.1% amylase, 5·10−4 mol/dm3 oleic acid, and temp. 30 °C), phospho-concentrate assaying 0.61% MgO, 13.14% SiO2, and 27.85% P2O5 with a P2O5 recovery of 55.45%, was finally obtained without the use of expensive depressants, e.g., phosphoric acid or sodium silicate. A tentative flow sheet for the whole process was postulated.

By Harald Ulrik Sverdrup, Anna Hulda Olafsdottir

The long-term supply of nickel to society was assessed with theWORLD7 model for the global nickel cycle, using new estimates of nickel reserves and resources, indicating that the best estimate of the ultimately recoverable resources for nickel is in the range of 650–720 million ton. This is significantly larger than earlier estimates. The extractable amounts were stratified by extraction cost and ore grade in the model, making them extractable only after price increases and cost reductions. The model simulated extraction, supply, ore grades, and market prices. The assessment predicts future scarcity and supply problems after 2100 for nickel. The model reconstructs observed extraction, supply and market prices for the period 1850–2020, and is used to simulate development for the period 2020–2200. The quality of nickel ore has decreased significantly from 1850 to 2020 and will continue to do so in the future according to the simulated predictions from the WORLD7 model. For nickel, extraction rates are suggested to reach their maximum value in 2050, and that most primary nickel resources will have been exhausted by 2130. After 2100, the supply per capita for nickel will decline towards exhaustion if business-as-usual is continuing. This will be manifested as reduced supply and increased prices. The peak year can be delayed by a maximum of 100 years if recycling rates are improved significantly and long before scarcity is visible.

Jan 26, 2021

By JOHN HOMER, Jacob L. Carr, Jonathan K. Hrica, Kathleen M. Stabryla, Iman Benbourenane, Jennica L. Bellanca

Given the recent focus on powered haulage incidents within the US mining sector, an appraisal of collision avoidance/warning systems (CXSs) through the lens of the available research literature is timely. This paper describes a rapid review that identifies, characterizes, and classifies the research literature to evaluate the maturity of CXS technology through the application of a Technology Readiness Assessment. Systematic search methods were applied to three electronic databases, and relevant articles were identified through the application of inclusion and exclusion criteria. Sixty-four articles from 2000 to 2020 met these criteria and were categorized into seven CXS technology categories. Review and assessment of the articles indicates that much of the literature-based evidence for CXS technology lies within lower levels of maturity (i.e., components and prototypes tested under laboratory conditions and in relevant environments). However, less evidence exists for CXS technology at higher levels of maturity (i.e., complete systems evaluated within operational environments) despite the existence of commercial products in the marketplace. This lack of evidence at higher maturity levels within the scientific literature highlights the need for systematic peer-reviewed research to evaluate the performance of CXS technologies and demonstrate the efficacy of prototypes or commercial products, which could be fostered by more collaboration between academia, research institutions, manufacturers, and mining companies. Additionally, results of the review reveal that most of the literature relevant to CXS technologies is focused on vehicle-to-vehicle interactions. However, this contrasts with haul truck fatal accident statistics that indicate that most haul truck fatal accidents are due to vehicle-to-environment interactions (e.g., traveling through a berm). Lastly, the relatively small amount of literature and segmented nature of the included studies suggests that there is a need for incremental progress or more stepwise research that would facilitate the improvement of CXS technologies over time. This progression over time could be achieved through continued long-term interest and support for CXS technology research.

Jun 17, 2022