Search Documents

By David C. Slack

In recent years public concern over the environment has grown enormously. A very aware populace has exerted pressure on its legislators to enact enforcement laws dealing with pollution. Among the different types of pollution, sulfur dioxide in the air is a large and readily identifiable constituent. Air pollution, according to the EPA, costs the U, S. billions annually with SO2 a major portion of this cost. Fossil fuel and oil fired power plants release better than 50% of the SO2 in the country. Thus great attention is being focused on the methods power plants are utilizing to control emissions. With a time schedule of compliance by early 1975, decisions are being made and systems chosen that will have to perform - and perform - and perform. Therefore, a large majority of the power plants are presently considering lime in the planning and operational phases of their stack gas desulfurization programs. The reasons for this are: Lime scrubbing has more development and pilot work completed than most other methods; the removal potentials are relatively high; the stoichiometric ratios are not excessive and, the process has relatively low capital and operating costs. Many pilot plant studies have been completed recently using lime and the first operational full scale lime scrubbing unit is now in the start-up phase at this time at Duquesne Light Company's Phillips Station here in Pittsburgh. Also, because of completed development work, the problem of solid waste disposal will also be tackled at this power station at the same time. There are various methods for the use of lime in scrubbing for S02, but for our purposes I would like to describe the cyclic wet lime process. This method called "Scrubber Addition of Lime" involves contacting the flue gas with a slurry of milk of lime.

Jan 1, 1973

By L. M. Pruett

The Arizona Legislature is currently in the process of considering mined land reclamation legislation in the 1994 legislative session. A bipartisan legislative study committee has drafted proposed mined land legislation. The committee has attempted to craft legislation that is appropriate for the unique conditions in Arizona. Existing Arizona and federal laws and regulations extensively regulate the environmental performance of mines in the state to protect public health, safety and the environment. The proposed mined land reclamation legislation does not replace or duplicate these statutory provisions relating to environmental protection. Instead, the purpose of the proposed legislation is to provide for the reclamation of land that is being mined and to fill the gap in existing laws by requiring the reclamation of land that currently is being mined or that has been mined since 1986 to provide for future land use. The legislation would require an operator to submit a reclamation plan describing the exploration operations, mining operations, post-mining land use and the proposed reclamation measures for review by a state agency. Financial assurance also would be required in an amount such that a third party could complete the approved reclamation measures. Arizona's mined land reclamation legislation would recognize Arizona's leading role in hard rock mining and emphasize the mining industry's economic importance to Arizona and the nation. Because mining operations necessarily require disturbing the surface of the earth to extract valuable minerals, reclamation requirements would be adapted to different conditions and would vary depending on site-specific conditions and on the commodity being mined. The current proposal does not identify the state agency that will administer the mined land reclamation program and approve reclamation plans, substantial changes to plans, and transfers of reclamation plans to other operators.

Jan 1, 1994

By W. C. Streib

A wide variety of materials have satisfactory to superior insulating properties and can be used to control the flow of heat, provide energy savings, improve personal comfort and contribute to personal safety. Such materials range from completely organic products--both of natural origin and synthetics--to completely inorganic. In many cases, thermal protective systems are actually combinations of both. Obviously, those insulating materials which are principally inorganic have the inherent advantages of low to minimal combustibility as well as utility at vastly elevated temperatures. Both of these properties are highly desirable in providing not only thermal energy conservation, but also personal safety in residential and commercial applications. As the thermal insulation needs of man and industry have developed, there has been an ever-increasing demand on the minerals industry to provide the resources required to fill these needs. On a global scale, industrial minerals have become the fundamental base upon which today's thermal insulation industry has been built. The use of minerals to control heat flow range from the most unsophisticated applications to those requiring the ultimate in scientific technology. In many cases the minerals are themselves converted in- to the major insulating media; for example, fiber glass, rock wool or refractory fiber. In other cases, minerals are used as the chemical reactants to form the binder matrix which in turn provides the product strength required for adequate handling and installation; for example, calcium silicate bonded products wherein the binder is the reaction product of lime and silica. In still other cases, low density mineral products are added to a high density binder System to provide lower weight and better insulating properties; for example, the use of expanded perlite in concrete.

Jan 1, 1976

By J. K. Ross, K. O. Hoal, S. K. Appleby

Understanding ore variability is a key factor in the geometallurgical analysis of a deposit and is beneficial to process development and mine planning. Ore variability is a function of the mineralogy of a deposit, in terms of both ore and gangue minerals and their textural relationships. This study integrates optical microscopy and quantitative mineral analysis to characterize the mineralogy and texture from 13 samples from different lithologic units at the Bingham Canyon Mine. The analysis identified several parameters, such as modal mineralogy, alteration assemblages, distribution of mineral phases and alteration assemblages and microfracture and void space distribution. These parameters can have an impact on the materials’ behavior during processing. This study demonstrates that quantitative mineralogical analysis can provide detailed information for improved understanding of ore variability.

Jan 1, 2010

By J. R. Gump

The term "rare earths" is used to designate a group of elements, Numbers 57-71 which are closely related chemically. They were called "earths" because their oxides resemble those of the alkaline earths, and the designation "rare" was originally applied because of their scarcity. Now many of these elements are known to exist in considerable quantities, and the term "Lanthanide" is applied to this group of elements, because of their similarities to lanthanum, the first element in the group. Many authorities insist on including yttrium, element Number 39, because of its extremely close association with the members of the group in nature and because of its similarity in chemical properties. It has been estimated that the combined rare earth group makes up about five-thousandth. of one percent of the Earth's crust, a higher percent than the common elements, lead, tin, zinc, arsenic, mercury, silver and gold. Cerium is by far the most abundant member comprising about half of the total amount. Yttrium, neodymium, and lanthanum are next in order; samarium, gadolinium, praseodymium, dysprosium, erbium, holmium, and ytterbium are increasingly scarce; while the elements lutetium, thulium, terbium, and europium are extremely rare. The rare earths as a group are metals, usually trivalent, forming basic oxides, and insoluble oxalates in dilute mineral acids. Their fluorides are also difficultly soluble; hence the rare earths or lanthanides may be separated, in general, from other elements by adding oxalic or hydrofluoric acid to a dilute mineral acid solution containing them. The most striking fact which characterizes these elements is the remarkable .similarity in both the physical and chemical properties of their compounds. Their main differences are in the solubilities of their salts and the basicity of their oxides, which vary between that of the alkaline earths and that of aluminum.

Jan 1, 1960

By S. E. Phillipson

The MSHA Technical Support, Roof Control Division's primary evaluation tool for coal pillar designs is the Analysis of Coal Pillar Stability (ACPS) program. However, ACPS is limited to evaluating interactions between two seams at a time, which is not ideal for complex multiple- seam scenarios. Further, it does not recognize the influence of strata properties in the interburden and cannot be used to evaluate individual pillars. We apply the Rocscience RS2 two-dimensional finite element program as a complement to ACPS. Complex multiple-seam scenarios can be characterized by a modified pillar stability factor where the ACPS single-seam development pillar stability factor is multiplied by the ratio of average single-seam development stress to the stress in the critical pillar at the multiple-seam stage, using the values of o as predicted by RS2. Several series of test examples involving two-seam analyses with isolated remnants, gob-solid boundaries, and high extraction areas of varying width were used to calibrate simulated gob properties such that the ACPS+RS2 method generated results that matched a traditional ACPS Stability Factor to within 13%. As high-extraction areas become wider and deeper, progressively stiffer gob is simulated by increasing the Young's Modulus property in RS2. After achieving calibration with the test series, three examples of complex multiple-seam scenarios were evaluated, using reasonable properties for strata types and thicknesses based on core log data. Resulting modified stability factors are reasonably close to those predicted by ACPS, although affected by units of sandstone in the interburden and gob shadows superimposed on remnant structures. This tends to show that even in complex multiple-seam conditions, applying ACPS to the worst-case interaction should usually result in an acceptable pillar design.

Jun 25, 2024

By Hemendra N. Kalia

The target to double the coal production by 1995 presents a formidable challenge to the coal mining industry. The mines of future, probably will be located in relatively difficult geological environment because of the exhaustion of the well defined bedded and easily minable deposits. To compound the problems of mining industry will be the reliance of power plants need for coal. The coal must reach the power plants on schedule to avoid expensive blackouts and brown¬outs. It will be imperative that the mines operate without interruptions and at designed capacities. The parameters which have been traditionally responsible for the interrup¬tions of production are: breakdown of production machinery, labor management relations and geological anomalies. Of these three problems, solutions for the first two can be arrived at by developing procedures to correct the situation. A planned maintenance and preventive maintenance program will go a long way in minimizing the equipment breakdowns. Labor relations will eventually improve as the miners begin to enjoy long-term employment. However, with the geological problems, the situation will probably continue to deteriorate and would require careful planning to minimize the impact of geological problems on production and safety. Some of the geological aspects which interfere with production are: faults, washouts, slips and slickensides, water bearing overlying strata, impuri¬ties in the coal seam, and presence of expansive clays in the coal floor. The design of large capacity mines will have to incorporate the geological distur¬bances and mine through them it may become very uneconomical to abandon producing sections because of the presence of the geological anomalies. This paper discus¬ses the geological aspects of coal mining which should receive consideration from the inception of the mining ventures. Pertinent geological aspects are discussed to develop the data base which will aid in evolving safe and efficient mine layouts.

Jan 1, 1976

By Henry Chajet

Good morning, it is truly an honor to have been invited to speak before you today Before I begin my update on MSHA's activities, I?d Like t o quickly say a few words about the American mining congress and its mission in Washington, AMC is a national trade association representing most of the producers of the nation's metals, nonmetals and coal, we also represent the manufacturers of mining equipment and supplies and the financial and consulting institutions which service the mining industry. It is the diversity of our representation which gives us our greatest strength in our petitioning efforts, the administration and the members of congress know that an AMC position is the result of the careful consideration of a vastly diverse group of mining concerns. Our president, Al Overton, perhaps has the best description of AMC when he speaks of us as "the mining industry's eyes and ears and its collective voice in Washington."

Jan 1, 1981

By M. G. Gorman

The effects of particle size, particle shape and degree of aggregation on n-dodecylamine flotation of -20 µ m quartz and glass beads were studied. A microflotation cell suitable for use with very fine particles was used in the flotation experimentation. Degree of agglomeration of particles was estimated by comparing size distributions of the quartz and beads in a dispersed system to size distributions in systems in which the collector was present. Results obtained show that in such flotation systems the fine particles are not generally present as individual particles during flotation but rather as aggregations. However, the quartz floats more readily than the beads indicating that there are some shape effects in the systems, considering the large specific surface areas of the materials it also appears that substantial amine consumption in the systems may limit flotation or lead to a requirement of greater reagent dosage for equivalent flotation to that tor larger particles.

Jan 1, 1990

By Jamal Rostami, Jürgen Schmitt, Rohola Hasanpour

"Double Shield TBMs can be used in fast track projects for accelerated completion where there is limited information available on ground conditions and there are possibilities of encountering weak ground and shear zones. As such, the shielded TBMs are the primary choice of the machines in long tunnels, but face the possibility of entrapment in squeezing ground, which entails long delays and major risks. This paper examines the possibility of using ground improvement methods to increase ground strength, and thus, increase the capability of the machines to cope with squeezing ground conditions. In this study, 3D finite difference simulation of a shielded TBM in squeezing ground was performed to estimate the operational parameters including required thrust to get a machine out of an entrapment. This analysis was also used to evaluate the possibility of preventing machine jamming by the implementation of pre-excavation ground improvement to increase the strength of the ground. INTRODUCTION In order to face adverse tunneling conditions especially using a shielded TBM in squeezing ground, new shield designs, with extra thrust and torque, step shield geometry with reduced shield diameter from front to the back, and conical shape shields have been used. In addition, many of the new machines have the capability to implement ground improvement at distances up to 50 m ahead of the face in order to reinforce the ground and further increase in their chances to cope with squeezing ground conditions. While these features have been added to the machine, there has not been a thorough evaluation of their impact on improving the chances to avoid machine jamming in weak rocks at high depth, which is conducive to rapid convergence of the ground."

Jan 1, 2016

By R. A. Jankowski

Although the number of operating longwall mining systems has remained relatively constant, longwall production levels during the last five years have increased significantly. In the United States, longwall mining now accounts for approximately 50% of all underground coal production. While longwalls are highly productive and offer other advantages, operations employing this method of mining continue to experience dust-compliance problems. This increased longwall productivity has meant that far more dust is being produced. An improved understanding of the longwall face-ventilation system and the advancement of face-ventilation technologies are necessary to ensure all face personnel are allowed to work in an environment that is free of excessive levels of airborne respirable coal mine dust. The Dust and Toxic Substances Control Branch, National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, examined several basic principles of the long wall face-ventilation system and has evaluated the effectiveness of numerous improved face-ventilation techniques for longwall mining systems. These include identifying improved techniques for measuring face-ventilation parameters on longwall mining sections and investigating the fundamental relationship between face airflow and the entrainment and dilution of respirable coal mine dust. Studies have been completed to determine the impact on face dust levels of using belt entry air to ventilate the longwall. Novel methods have been identified to increase the face air¬flow and to manage face airflow to effectively minimize dust exposure to face workers. Unique systems of auxiliary face ventilation have been developed and evaluated at full-scale, simulated longwall test facilities. The theoretical and applied aspects of each of these principles and technologies are discussed. Application of these results throughout the longwall mining industry, as documented from surveys conducted in the early 1980s and 1990s, have reduced the health hazard associated with excessive exposure to respirable coal mine dust.

Jan 1, 2000

By John Ralston, Rossen Sedev, Nicola Richards, Quinn Anthony, Geoffrey Reynolds

Derivatised 2,4-diketopyrimidine groups have been anchored to planar gold surfaces as self¬-assembled monolayers (SAMs) for chemical and photochemical studies. Three derivatives, 5-methyluracil (thymine), 5-trifluoromethyluracil and 5-nitrouracil, were chosen for the specific moiety present at position C-5, which can exert strong or weak inductive effects on the adjacent aromatic ring. The measured acidity constants decrease from 5-methyluracil to 5-nitrouracil as the inductive properties of the group at C-5 position increase. When grafted to the surface the acidity constants increase, albeit still adhering to the expected inductive trend. The functionality also exerts an influence on the surface wetting properties. Surface wettabilities indicate that the orientation of the pyrimidine groups at the surface occurs so that the C-5 position has a direct effect upon the surface chemistry. Upon dimerisation the surface contact angles increase signifi¬cantly. At pH 11 the contact angle changes reflect that the dimer has a higher pKa than the monomer. The monomer surface is deprotonated at this pH while the dimer surface is partially deprotonated, leading to changes in contact angle of up to 22 degrees. Large changes in contact angle were observed for 5-nitrouracil which were independent of surface charge and were appar¬ently due to conformational changes alone. Electrowetting of three fluoropolymer surfaces by electrolyte solutions was studied with the sessile drop method. The electrowetting curve (contact angle/potential) is analogous to the elec¬trocapillary curve (surface tension/potential) and may be described by a combination of the Young and Lippmann equations. We demonstrate that for some specific surfaces a systematic deviation occurs at positive potentials. This departure is attributed to double layer effects, namely the adsorption of hydroxide and halide anions. pH, ionic strength and polymer composi¬tion can all influence electrowetting behaviour.

Jan 1, 2003

By E. Watkins, M. B. Daza

Although there have been great advances regarding the understanding of mine fires in underground mines in the last century, fires remain high risk incidents. During fire scenarios, many crucial decisions and actions can be made that greatly influence the outcomes of these scenarios. Underground worker decisions are mainly based on training and experience, which in some cases can be complemented with previous analysis of fire effects. In order to review the guidelines that should be taken into account for this kind of examination, a numerical analysis of effects produced by a shuttle car fire under five different ventilation conditions was carried out. The analysis provides some insightful recommendations for firefighting personnel such as time for direct attack and best attack position for first responders and fire brigade groups. Also, the most critical parameters for each scenario were determined. Finally, all results were systematically organized and a first approximation of a fire classification based on the tenability limits was provided for first responder and fire brigade groups. The methodology used in this study for the fire classification could allow for the most appropriate decisions by firefighting personnel increasing the probability to put fires out without compromising their health and safety. INTRODUCTION While there have been great advances regarding the causes of mine fires in underground mines in the last century “small fires have occurred and always will occur in underground mines” (Conti, Chasko, Wiehagen, & Lazzara, 2005). The response time and decisions made during an underground mine fire are critical elements that have direct influence on the event outcome. Mine fires can grow in size quickly causing catastrophic consequences, thus rapid and suitable response actions can result in the difference between an minor emergency situation and a disaster. Upon the confirmation of a fire, a decision must be made regarding whether to fight the fire or evacuate the mine. Even though all underground coal mines possess emergency response plans and firefighting personnel are highly trained, decisions can be complemented with previous numerical analyses. Such analyses could contribute with the knowledge of potential fire effects and consequently with fire preparedness in the mine. Preparedness in underground mines is an important element to reduce the probability of the negative consequences of a mine fire. The time elapsed between the detection of the fire and response in the early stage is a serious component since small fires can produce larger and more serious consequences. If a mine fire cannot be put out within the short time after discovery, the chance of getting the system back in balanced or the success of safely controlling and extinguishing a mine fire is reduced (Conti et al., 2005, Conti, Chasko, Wiehagen, & Lazzara, 2000, Trevits, Yuan, Teacoach, Valoski, & Urosek, 2009, Brake, 2013). As confirmed by Conti and others, if a mine fire cannot be controlled by direct firefighting methods the probability of extinguishing the fire, without sealing is greatly reduced (Conti et al., 2005). However, response actions such as direct extinguishment must be carried out without compromising the health and safety of the firefighting personnel (Kim, Lönnermark, & Ingason, 2010).

Jan 1, 2019

By Chinmay Shingote, Robert Visintainer, Renjie Ke, Jaikrishnan R. Kadambi, John Furlan

Hydrocyclone separators are widely used in various industrial applications in the oil and mining industries to sort, classify, and separate solid particles or liquid droplets within liquid suspensions, which are considered to be multiphase systems. Numerous valuable studies have been conducted in recent years to investigate the flow fields inside hydrocyclones. However, much of the information regarding the performance of cyclones in the literature has limitations and much of it cannot be considered as completely applicable to most real-world applications; many of the studies investigated the flow fields within extremely simplified hydraulic designs that are not representative of the complex geometries or large sizes which are typical in industry. Therefore, in this study, the two-phase flow system inside the actual hydraulic geometry of a milling circuit hydrocyclone is explored with the aid of both computational and experimental techniques (particle image velocimetry (PIV)). More specifically, the flow field with an air core has been investigated. In addition, the air-liquid two phases flow in a hydrocyclone might cause some challenges on both the computational and experimental sides. Two turbulence models are utilized in the numerical calculations: the Reynolds stress model and large eddy simulation. The computational studies are mainly focused on the local flow behavior and the prediction of the dimensions and shape of the air core. Different section planes of hydrocyclone are selected as planes of interest and divided into several fields of view (FOV) for PIV measurements. Two-dimensional experimental velocity vector maps are obtained in each of the fields of view. The computational results are validated globally using pressure and flow rate readings at the boundaries and locally by comparison to the PIV velocity vector maps and profiles.

There are bound to be changes with age, so I should not have been surprised or disappointed when what I had considered as high ad- ventures were much fewer and more widely scattered in the last 20 years of my long and active business life. But such adventures came until I was past 80 years of age and no one could expect more than this. Frequent visits to mines in this country and Canada and directorships in Bralorne and its subsidiaries, Homestake Mining Co., Bradley Mining Co., and the Bunker Hill Co.; and Copper Range Co. and its great new White Pine mine in Michigan, lasted far beyond the usual retirement age. The least happy part of my last two decades of active life was the death or sickness of many of my old friends. Hubert d'Autremont, whose friendship no one could replace, died suddenly in 1946. Henry Carlisle and Temple Bridgeman, for many years office associates, had heart attacks that cut down their activities far too soon. Many other less intimate friends died or became ill, but I knew that with advancing years such losses were inevitable. These memoirs would be endless if they covered all of the unusual work and associations I found in the last 20 years. So I must confine the rest of my recollections to expeditions that would have thrilled any engineer at any time. Masaro Mine, Mindanao, Philippines The first of the four "high adventures" came late in 1949, when I was 65 years old. For over a month I had been discussing reported rich lead-silver-copper properties in the Philippines with Thayer Lindsley and other officers of Panaminas. A competent and agreeable "Elderly" (not as old as I was) engineer named Ward Williams had talked with Thayer about high grade mines in a remote part of the

Jan 1, 1976

By David Pentz, Paul Hodges

GENERAL INTRODUCTION The object of this paper is to discuss those aspects of open pit mine design which are affected by geotechnical factors. The temptation exists for some practitioners of geotechnical engineering to believe that this relatively new engineering discipline is the ‘be all and end all of mining.’ In the opinion of the authors, this is fallacious but, as our ability to put numbers to the behaviour of rocks and soils improves, it is clear that geotechnical engineering will become an integral and important part of designing and operationg mines success- fully. Open pit mines in the context of this paper also includes open cast mines, where the 'ore" is extracted and the waste material is immediately replaced or ' backfilled in the mined portion of the pit. Open pit mines operating today move from very small tonnages a day to in excess of 400,000 tons per day. Several mines are operating and are being designed to capital expenditure for such projects in some cases exceeds five hundred million dollars and in a few cases will exceed one billion dollars. The size of this investment means that financing will have to be provided from banks or joint partnerships. This financial environment means that planning will be carefully scrutinized by experienced representatives of financial institutions or other mining companies. All too often a project has been put in jeopardy because the personal desire of one or two men to make a project proceed has caused incomplete planning or perhaps in some instances deliberately leading observers 'down the garden path.’ In our opinion the day is rapidly arriving when the quality, logic, practicability and completeness of the planning will make the difference between securing financing or not and, in the cases of existing open pit mines, of the difference between survival and closure.

Jan 1, 1977

By A. MacG. Robertson

INTRODUCTION The tailings, or solid waste, remaining after uranium has been extracted from an ore and the liquid wastes associated with it contain both radioactive and other substances which, if released to the environment, may have a detrimental impact on man and his environment. Although the radioactivity of the waste is of natural origin, the mining and milling process results in bringing the radioactive ore to the surface, changing its chemical and physical form, increasing its mobility and, therefore, enhancing the potential radiological exposure to man. Exposure to radionuclides released from a tailings impoundment, while small as applied to any one generation, can be made large by counting far into the future, large enough to be the dominant source of exposure from the nuclear fuel cycle, Cunningham (1978). Increasingly it is being found that where the prime concern was initially the radionuclide releases, the release of other pollutants and contaminants may be of equal or greater concern. While there is a definite benefit, at least to present generations, resulting from the recovery of uranium, current and long-term concerns require that consequential present and future releases be kept as low as is reasonably achievable. Design practice, to minimize this release, is currently passing through a technical revolution; precipitated by public and institutional concerns. New techniques and methods are, therefore, being actively sought and continuously implemented. Because of the complexity of the pollutant release mechanisms and the sitespecific nature of each impoundment site and tailings product, a wide variety of site selection and design options have been implemented or considered. It is often possible to design a number of satisfactory tailings disposal schemes which differ widely in nature and cost. This paper outlines the principal areas in which options are available and discusses some of these options. Both operating and post-decommissioning conditions are consi-

Jan 1, 1980

By A. Bascetin

The human requirements have increased rapidly depending on population density and urbanization thus industrialization has grown steadily. As a result of the situation, the greenhouse gas emissions into the atmosphere and the global warming have increased slowly. Today this effect has continued to increase. Therefore, the effects of greenhouse gases in all areas of production must be controlled. The study presents the methods of determination the CO2 emissions (CO2-e) and energy consumption in aggregate production. The aggregate constitute approximately 70% by volume of concrete that has widespread use as construction material in the world. One of the most important elements in today's terms is sustainable use of resources and minimum CO2 emissions (CO2 + CO + NOx + CH4.vb.) at every stage of production of aggregate. Therefore, these elements must be taken into consideration in the aggregate production standards. The choice of production method of aggregate is very important for optimum use of energy and effects of greenhouse gas emissions. So the properties of the aggregate material must be known well to obtain the target. Within the scope of this study, the unit value of CO2-e that release when the production of aggregate in different formations is determined for our country. Thus, the effects of green house gas emission can be evaluated according to the characteristics of material in aggregate production planning. In this study, energies consumed during the production of aggregates at a quarry in Istanbul Cendere region were investigated by taking the different formations encountered at the quarry into consideration. The unit CO2 emission values per ton of produced aggregates were calculated as a result of this investigation. Besides, energy consumption values of previous months at this quarry were taken and the unit CO2 emission values were also calculated.

Jan 1, 2011

By Roger G. Haga, Richard P. Campbell

Introduction Project scheduling . . . . • What is it? • Why is it done? • Who does it? • How is it done? • When is it done? These are some of the questions that will be addressed in this paper. It is intended that by exploring these questions, an understanding of project scheduling, its purpose and benefits can be achieved. The purpose of this article is not to describe in detail "how to schedule", but rather to give an overview of the scheduling function on a project. A successful scheduling effort is dependent upon the people responsible for developing, implementing, and monitoring the schedule, and the tools and procedures that are used. These three elements are integral components of project scheduling. What is it? A schedule is the integration of network relationships, resource constraints and the calendar. The schedule identifies when the activities "will" be done, while the network states when they "must" be done. Networking techniques are the most widely accepted scheduling tool for complex projects. The benefit of the network is the simplicity in illustrating, presenting and analyzing the dependency relationships of a project. The logic network is the foundation of the schedule. When calendar dates are applied to the logic network, it becomes a schedule which provides the basis for evaluation of project status, forecasting the occurrence of events and controlling the project. The sequence of activities that requires the longest time to complete determines the overall duration of the schedule. This longest sequence of activities is called the "critical path". The "critical path method" (CPM) is used to describe this particular schedule network methodology. The two common conventions of CPM networks are the "arrow diagram met hod" (ADM) and the "precedence diagram method" (PIM). There are arguments in favor of each of these two methods, and usually the one that is used is a matter of personal preference, project directive or corporate procedure.

Jan 1, 1986

By J. Slivnik, A. Stergarsek

[The site] [Z]irovski vrh uranium ore deposit is located in the extreme north-western part of Yugoslavia, some fourthy kilometers from the capital of Socialist Republic of Slovenia, Ljubljana, not far from the Italian and Austrian border. The sandstone type deposit of uranium ore with medium grade is located in a foothill of Julian Alps. The site shows some typical conditions for this region, which demand special attention in respect to the incorporation of an uranium treatment facility into environment. Among these specific conditions the following site characteristics should be mentioned: - populated area of agricultural and recreational value, - unconvenient climatic conditions with excessive rainfall and long lasting temperature inversions in the winter time, - very pure surface and underground waters which supply the drinking water reservate for large area including the capital of Slovenia, - sharp relief, - unconvenient geological structure. The choise of technology The intention to produce uranium and at the same time respecting the natural characteristics and existing uses of the site made the design of the ore treatment facility relatively difficult one. In general, there were two basic alternatives available perform the task. First alternative was to adopt the usual technological flowsheet with wet tailings disposal and with discharge of used water i.e. liquid effluents into the river. In order to prevent the negative impact of such technology on the sourrounding area sophisticated water purification installation and costly measures in wet tailings disposal e.g. impermeabilisation of large areas by concrete injections, large dam constructions, uncertain capturing of the water sources should be employed. Second alternative was to modify the usual flowsheet by employing the maximal recycling of liquid effluents to the process and to dispose the solid

Jan 1, 1980