Search Documents

By A. S. Malicsi, Vathsala Rajagopal, I. Iwasaki

Corrosion and abrasion properties of a series of chromium-containing, cast-iron balls, with Cr contents ranging from 0% to 29%, were evaluated and compared with austenitic stainless-steel and mild-steel balls. Marked ball wear tests were performed on artificial ore samples consisting of 95% quartzite, with either 5% pyrrhotite or 5% chalcopyrite, under a nitrogen or oxygen atmosphere. The electrochemical mechanism was investigated by correlating the corrosive wear with the corrosion currents obtained from potentiodynantic polarization curves under abrasion. Flotation recoveries were determined on a 95% quartzite + 5% pyrrhotite sample ground with various cast-iron ball materials under an oxygen or nitrogen atmosphere. Electrochemical results are found to be in good agreement with flotation results and with corrosive wear data obtained from marked ball wear tests.

Jan 1, 1993

By O. R. Swendseid

The Mountain Con mine is a relatively old, deep mine located in Butte, Montana. Operations at this property through the present shaft were started before the turn of the century. As mining progressed to depth, increasing demand for ventilation facilities and changing mining conditions made it convenient to convert some nearby shafts to airways. The fact that these openings had not been originally planned for use as airways made it necessary in some instances to utilize long and inefficient already-estab¬lished entries to service working areas. This situation existed in the Lexington fresh air system. The Lexington system consists of a vertical, 3-compartment shaft extending from surface to the 3200 level and a series of 2-compartment air raises and old horizontal-haulage openings extending into a mining area several thousand feet west of the Lexington shaft between the 3900 level and the 4200 level. Because of restrictions and high resistance in the portion of the system between the bottom of the Lexington shaft on the 3200 and the mining area on the 3900, the capacity of this system is only 85,000 cubic feet of air per minute. It was calculated that the capacity of the system could be in¬creased to meet the demands of the current mining program in this section of the mine by utilizing a single, straight, horizontal air course on the 3200 and by driving an inclined air raise 740 feet long between the 3900 and the 3200.

Jan 1, 1967

By D. W. Smellie

This paper is a review of technological progress in mining geophysics during the past decade. This has been the most significant period in the history of mining geophysics. Among the already existing; techniques, instruments for ground -magnetic and electromagnetic prospecting, were developed that are more, portable and faster to operate. Induced polarization equipment came into widespread use. Airborne instruments of various types became available and were used to survey large areas. Drillhole instruments were developed and have had some use, and it is to be hoped will be used to a greater extent in the future. Two revolutionary new methods, the AFMAG and INPUT, were developed. The wisdom of attempting to cover such a broad field in a single paper might be questioned. There is the inevitable problem that each topic must be discussed very briefly. However, while papers describing individual instruments have appeared, many have yet to be described in the technical literature. The evolution of the ground magnetometer and electromagnetic instruments has not been discussed. It is only recently that a review article has appeared on airborne EM. The existence of review literature on some topics has meant that they are given less emphasis in this review than those topics inadequately covered. It will also be observed that stress is laid on "chose instruments that are generally available to the mining industry rather than those developed by individual exploration companies for their own use.

Jan 1, 1963

By B. K. Kejriwal, A. K. Ghose

Under specific geological environment, the full extraction of a coal seam is not possible either because of its extraordinary thickness or the presence of surface structures and bodies of water or because of the conditions prevailing in upper seams. Not uncommonly, therefore, for working such seams, pillars of coal are left for the permanent support of the overburden, and voids around the pillars are filled with sand to strengthen the pillars and prevent their deterioration with time. However, the paucity of river sand has focussed attention on the need for alternate strategies including trials with partial filling of the voids. This study has sought to examine in the laboratory the effects of partial and complete filling on the ultimate load bearing capacity and post-failure behaviour of small, tall pillars using artificial material.

Jan 1, 1986

By G. T. Adel

The growing interest in column flotation has created a need for a fundamental scale-up procedure which is capable of meeting the necessary design and control criteria for industrial columns. Unfortunately, most of the avail able scale-up procedures deal with column diameter only and not overall column volume. Current work focuses on the effect of bubble size distribution and air hold-up on the scale- up of column volume. A series of pressure transducers has been used to measure air hold-up along the length of a bench-scale column. These measurements have been used to validate a mathematical model of the air phase. In addition to scale-up, the model appears to have the potential for use in control of air hold-up and bubble size.

Jan 1, 1990

By Kathleen S. Smith, Katherine Walton-Day, James F. Ranville

Four different scales of observation were used to evaluate the potential effects of a fluvial tailings deposit on water quality along the flood plain of the upper Arkansas River south of Leadville, Colorado. First, we collected surficial material and subjected it to batch water-leaching test. Second, we excavated and leached an intact eight-inch diameter core. Third, we examined the water quality of the shallow ground water beneath the fluvial tailings deposit, and fourth, we monitored water quality along a 5-km reach of the adjacent Arkansas River. Leaching of surficial samples indicates that there is a reservoir of readily water-soluble material yielding elevated metal concentrations and high acidity. However, there are minimal measurable water quality effects of the fluvial tailings deposit on the adjacent reach of the Arkansas River.

Jan 1, 2000

By James D. Piper

In the summer of 1957,9 the University of California sponsored a World Conference on Prestressed Concrete in San Francisco to which were invited a number of Soviet engineers. While attending the conference, these engineers in turn asked the University to form a delegation of American engineers to visit the Soviet Union the following year for the purpose of studying Soviet advances in concrete technology. A six man delegation was formed, and the dates of the Russian tour fixed for May 10th through May 21st, 1958. Before arriving in the Soviet Union, the American Delegation attended the Third International Congress on Prestressed Concrete in Berlin. While there, we noticed that the delegation from the U. S. S. R. used displays and showed motion pictures of many construction projects which we later were shown in Moscow. Our delegation left East Berlin by Russian aircraft on May 11th, and arrived in Moscow that afternoon. We were met by our Russian engineer hosts from The Academy of Construction' and Architecture who made all subsequent arrangements for our itinerary. This Academy has no counterpart in the United States. It. does 40 per cent of all engineering-and scientific work in the building construction field and coordinates 60 per cent of that done by other Soviet agencies. Due to the prestige of the Academy in Russian affairs, our delegation was able to obtain a surprisingly broad picture of construction activities in Moscow and Leningrad in just ten days time

Jan 1, 1960

By D. E. Ranta, Jean-Michel Rendu

It is generally recognized that geologic input is required for the results of a geostatistical study to be meaningful. However the link between geology and geostatistics is often complex and not well understood. A geostatistical evaluation can be divided into four phases: Background discussions, computation, reserve reporting and reserve audit. Each one of these phases is described, as well as the role the geologist should play during their completion. This role will vary depending on the geology of the deposit being studied, the geostatistical method chosen and the computer hardware and software being used. The geologist's acceptance of the results is needed if the geostatistical model is to have any credibility. The most significant obstacle to a meaningful study comes from the difficulties geologists and geostatisticians often encounter when attempting to communicate with each other.

Jan 1, 1992

By John Litz

The term "refractory gold ores" refers to a wide number of ore types which are not readily amenable to direct cyanidation. A number of processes have been used commercially, and a number of others have been proposed and in many cases pilot tested. The selection of the appropriate process for an ore should not be arbitrary. Ore grade may preclude some processes, but a good understanding of the ore mineralogy can guide the selection. Many present gold operations and many potential gold operations have faced or are facing problems with refractory gold mineralization. We at Hazen Research have had the opportunity to perform bench testwork and in some cases, pilot plant testing on a number of refractory ores. The data included in this paper are excerpted from the testing of fifteen ores which cover a wide range of mineralogical compositions. This paper is not intended to be a treatise on the processing of refractory gold ores. In many of these gold projects, not all of the standard process alternatives were evaluated, nor was adequate mineralogical work performed. Such is the dilemma of contract research. "If I believe that I don't need it, why should I pay to have it done." The intent of this presentation, therefore, is to show how different ores respond to the various processes, and to demonstrate that one must have an open mind when developing a process for a specific refractory gold ore.

Jan 1, 1998

By John E. Wallace

A recent study by the New York Trap Rock Corporation has conclusively determined that the number of blasting complaints is directly related to the noise produced by the blast. In turn it has been known for some years that the noise produced by the blast is directly related to atmospheric structure of temperature, wind, and humidity in the vertical direction. Normally during daylight hours the temperature decreases with altitude at the rate of about five and one half degrees per thousand feet on a sunny day, and to somewhat lesser amounts on cloudy days. Consequently, sound travels slower with altitude because of the lower temperature, and the sound rays tend to bend skyward, and are soon dispersed in the atmosphere. Quite frequently, however, the temperature increases with altitude, and just the opposite effect is attained. That is sound rays are bent downward, and sometimes reach the ground with intensities approaching that at the source. When the temperature increases with altitude a temperature inversion is said to exist. Less frequently than these two atmospheric conditions a condition is observed where temperature remains constant with altitude. This is called an isothermal atmospheric condition, and sound passing through this type of atmosphere tends to travel in straight lines, neither bending upward nor downward. The sound will be greater than normal near the blast, but will dissipate rapidly with distance from the blast site with no zone or zones of silence.

Jan 1, 1962

By Dean S. Rogers, R. A. Metz

The conventional role or exploration, development and grade control is examined in this paper within the context of the many and varied types of gold occurrences which are found at the Dome Mine. The account endeavours to trace the development of the total ore evaluation process, from diamond drilling through the exploration and drifting stage, to the stope development and planning phase of the operation, with an emphasis on sampling techniques and assaying procedure. The concept of ore reserve calculations is developed and the practice of grade control is described. In summary, the role of the geological, the engineering and the mining department is presented in relation to the contribution each has to make in the evaluation and exploitation of ore from one of the world's classic Archean gold deposits.

Jan 1, 1992

By K. S. Narayanan, Marcia L. Bartges, K. S. Venkataraman

The starting powders' physicochemical properties and consistency are essential for technical ceramic products to meet their performance specifications. The need for finer and more consistent powders has opened new technologies for synthesizing powders from atoms and molecules. However, submicron and near-micron powders obtained from conventional comminution and classification techniques are still competitive. This paper shows several examples from electronic ceramic applications of how we can use powder characteristics for micromanaging by design the ceramic properties such as the green and fired densities, slurry rheology, shrinkage during sintering, and the microstructure of the sintered bodies. The cross-disciplinary nature of the technology requires that the researcher not only should have a firm grip on the fundamentals of one or more disciplines, but also should be generally aware of the intricacies of other disciplines as well.

Jan 1, 1992

By T. M. Gurr

It is estimated that in excess of one-half million chemicals are used throughout the American workplace. Hundreds of new chemicals are also being introduced into the workplace annually. Exposure to some of these chemicals can be harmful to workers and to the environment. The Occupational Safety and Health Administration (OSHA) estimates that approximately 25% of the U. S. labor force or approximately 25 million workers are exposed to one or more chemical hazards each year. OSHA has determined that this poses a serious problem for workers exposed to such chemicals. Chemical exposure may cause safety and health problems. Health problems can include a cause or contribution to heart ailments, kidney and lung damage, sterility, cancer, burns, and rashes. Safety hazards can include the potential to cause fires and explosions and other serious accidents.

Jan 1, 1989

By Gary F. Meenan

Continuous pi lot scale dewatering tests compared the performance of the vacuum disc filter with that of the screen bowl and the solid bowl centrifuges. The test results allow the a priori prediction of plant product moisture based on the feed particle size. This information is useful for selecting the best dewatering device for a given size material and for optimizing the dewatering performance of existing plant installations. Quantitative information was gathered on the ability of filter aids to improve the filtration rate of fine coal slurries. A polymeric flocculant and oil were added to the disc filter feed material at various dosage levels. Both filter aids increased the disc filter output. For the coal tested, the flocculant filter aid achieved higher filtration rates at a lower cost.

Jan 1, 1988

By Donald D. Haas

This presentation will discuss a mine owner's evaluation to utilize a contract miner in the development and production of gold properties. I will address both the quantitative and subjective aspects of the evaluation process. The quantitative aspects include cost evaluation, capital preservation, acquisition and disposal of new and used equipment, administrative costs, recruiting and training, and organizing a staff and craft labor force. The subjective areas of this discussion include corporate philosophy, administrative concerns, contractor competence, loss of owner control, operating flexibility, financing assistance, recruiting and training program utilization and risk reduction. The evaluation of alternatives provides a system for comparing, on a cost basis, an owner/operator system vs. a system using a contract miner. The supplement provides a concept on how a contract miner may be the cost effective system to be utilized.

Jan 1, 1989

By R. A. Bergman, P. G. Thornhill

Development of the Falconbridge Ferronickel Process for treatment of lateritic nickel ores began with laboratory work in 1955, the year the Company commenced exploration of its concession in the Dominican Republic. Process development centred on selective reduction originally directed to producing calcines amenable to ammonia leaching, but later found suited to electric smelting. The reduction step of the process was developed in a 25 tpd shaft furnace pilot plant located in the Dominican Republic, to which was later added an electric melting furnace. After almost 3 years of development work on this scale the plant was expanded to 100 tpd for fixing design data for a commercial plant. This took the form of the 30,000 ton per year Nickel Ferro-nickel Complex of Falconbridge Dominicans, which started up in 1971.

Jan 1, 1979

By Wang Dianzuo, Luo Lin, Hu Yuehua, Qiu Guanzhou

This paper introduces a novel classification approach named the flotation classification approach which works by controlling interactions between particles. It differs considerably from the conventional classification processes operating on mechanical forces. In the present test, the micro-bubble flotation technology is grafted onto hydro-classification. Selective aggregation and dispersion of ultrafine particles are achieved through governing the interactions in the classification process. A series of laboratory classification tests for -44 pm kaolin have been conducted on a classification column. As a result, about 92 percent recovery for minus 2 pm size fraction Kaolin in the final product is obtained. In addition, two criteria for the classification are set up. Finally, a principle of classifying and controlling the interactions between particles is discussed in terms of surface thermodynamics and hydrodynamics.

Jan 1, 1995

By Welland L. Ott, Hans J. Rumland

The Falconbridge Dominicana laboratory receives samples from all parts of the operation. Ore, metal and oil samples are taken by operating departments, gas and water samples by the laboratory staff. Physical sample preparation is essentially standard and produces comminuted samples for wet-chemical analysis and X-ray fluorescence analysis (XRF). T he main operating sections of the laboratory are described indicating in each case the type of instrumentation and method used, sample types analysed and comments on problems experienced. Emphasis is given to the sample preparation and X-ray sections especially with regard to the difficulties caused by our heterogenous ore material, calibration of the instrument and operational malfunctions. General problems related to our remote location and the tropical climate are discussed. Limited statistics on instrument availability, and stability, accuracy, precision, etc., are given.

Jan 1, 1979

By S. Subbarayan, S. Chander, M. S. Klima

A laboratory study was conducted to investigate the potential for recovering anthracite from coal preparation-plant tailings. The study included washability analyses, cyclone simulations and froth flotation testing Samples were collected from either the tailings streams or the slurry ponds of five anthracite-cleaning plants. From each sample, a washability analysis was conducted on the 28x100 and 100x200-mesh fractions. Using the above data, along with published partition data, simulations were performed with various cyclone-staging arrangements for both water-only and dense-medium cyclones treating the 28x200-mesh fractions. Separate froth -flotation tests were conducted on the 28x100- and 100x200-mesh fractions from three of the plant samples. The washability, simulation and flotation results are presented as grade-yield curves.

Jan 1, 1996

By K. J. Stratford

The selection of a suitable mathematical function for the modelling of the partition curve for dense medium cyclones is discussed. Five alternative functional forms (based on three basic functions) are compared using data obtained in the course of an extensive experimental study of a 610mm dense medium cyclone. It is shown that, for adequately sampled tests, any of the functions may be used, although a function based on the Weibull distribution is shown to be most suitable. Where data are poor, all functional forms exhibit disadvantages, notably in terms of a reduction in precision of parameter estimation. This problem can be exacerbated by the complex numerical techniques required to estimate the parameters of a particular function. A set of ideal requirements for a performance function are presented.

Jan 1, 1986