Search Documents

By William J. Orlandi

The intent and scope of this paper is to present to you, as concisely as possible, the problems and requirements -- and what we consider advantages -- of all-belt haulage in a modern underground coal mine. Mine No, 10, at Pawnee, Illinois, was opened in 1951; consequently, all the planning and consideration given to haulage selection was based on information then available and on Peabody Coal Company? s experience to that date,

Jan 1, 1961

By John F. Parmeter

On August 29, 1989, the Department of Labor, Mine Safety and Health Administration (MSHA), published a Federal Register concerning a new proposed rule on air quality, chemical substances and respiratory protection standards. As of this writing, their proposed rule has not become a standard. However, with little revision it could be expected to become a standard, and we in the mining industry will be expected to adhere to and enforce it.

Jan 1, 1991

By D. B. Stephens

Milling operations throughout the world have created vast amounts of waste by-products, or tailings, which are often disposed on the land surface. The wastes may be disposed behind dams, on untreated ground, or on compacted clay or synthetic liners of impoundments and trenches. Often one of the principle concerns of environmental regulatory agencies is whether seepage from the waste pile could move through the vadose zone to the water table and possibly contaminate an aquifer. The seepage may be generated by the drainage of liquids initially deposited along with the tailings or by infiltrating meteoric water which leaches solutes from the tailings. The purpose of this article is to discuss some of the commonly held assumptions regarding storage of seepage wastes in the unsaturated zone. The significance of recent studies of water movement in dry climates which pertain to tailings site selection will be presented. The paper is relevant not only to seepage from impoundments at mill sites, but to many other fluid waste impoundments as well in part this article reinforces earlier work by Stephens and Siegel (1980) and an excellent review paper by McWhorter (1985). The present report addresses considerations in porous media; for a discussion of the effects of fractures and anisotropy in the unsaturated-zone, refer to the paper by McWhorter (1985).

Jan 1, 1985

By Keivan PakIman, Maziar Pasdarpour

Transportation tunnels are highly sensitive to ground movements and are required to be stable and secure for safe operation. In urban areas, the interaction between tunnels and adjacent piles, which are widely used to support buildings and other structures, requires careful consideration. The seismic response of tunnels may vary depending on the lateral stiffness and strength of the tunnel walls, while the axial loading and seismic impact of adjacent piles may cause soil displacement and stress changes that can damage the tunnel lining. As a result, tunnel owners often impose strict limits on the design of new piles lying close to existing tunnels including maximum allowable tunnel deformation, stress change limits, and minimum tunnel to pile separation distances. This paper describes a numerical analysis of the inuence of the axial loading and seismic impact of bored pile foundations on subway tunnels, undertaen using the nite element software laxis D. ased on the results of the numerical analysis, the paper suggests a more realistic and less conservative approach for designing piles in close proximity to transportation tunnels. INTRODUCTION The interaction between tunnels and adjacent piles can cause stress changes and displacements in the soil and structures which may adversely impact structural performance and tunnel safety. It is therefore important to take account of relative load transfer and piling conguration when designing new piles in

Jun 23, 2024

By Paul E. Senseny

Data from triaxial compression tests per- formed at confining pressures between 0 and 100 MPa are used to evaluate parameters in a contitutive model that is based on microcracking. The tensorial formulation is reduced to equations that are specific to the simple Loading imposed in triaxial compression tests. Procedures for evaluating the model parameters are described, dependence of parameter values on confining pressure is discussed, and prediction of failure is assessed.

Jan 1, 1986

By Kathleen Y. Knoebel

This paper describes a graphical mini computer system called MPASS 2 (Mine Performance Analysis/Simulation) which has been designed to conduct analysis of underground room-and-pillar mining operations using both conventional and continuous mining methods. Dynamic, graphic displays of mine face machine activities are presented on the CRT screen to provide extensive visibility into underground mining activities. MPASS 2 consists of: an interactive inputting system that graphically creates a room-and-pillar mine and describes the mine when production is initiated; a time-step simulator that produces statistical summaries of shift activities and uses CRT screen graphics for accelerated-time display of machine activities and delays; a statistical analysis subsystem for analyzing mine performance data; an industrial engineering system that permits users to enter actual machine activity statistics and replay mine operations on the CRT screen; and a data management system to store historical performance information on mine characteristics and operations. MPASS 2 operates on a Hewlett-Packard 9845B mini computer with 450 K bytes of extended memory, and is written in H-P BASIC. It has been installed at Freeman-United Coal Mining Company in West Frankfort, Illinois and at the U. S. Department of Energy Pittsburgh Mining Technology Center. Applications include production system simulation, industrial engineering analysis, production scheduling, new equipment evaluations, and training.

Jan 1, 1982

By Judith A. Marks, Deane K. Smith, Jan M. Mutmansky, Maria Klimkiewicz

The mechanical mining of coal seams where roof, partings, and floor rock are extracted along with the coal often introduces large numbers of quartz particles into the mine atmosphere. This study concentrates on the quartz properties in situ and in the airborne dust to determine how they are released from the source rock and whether they are fractured by the mining machinery. Three mines using drum-type continuous miners from different geographic areas were sampled to provide a data base. The roof and floor rocks were primarily siltstones containing 5% to 25% quartz measured by the X-ray powder diffraction (XRPD) method. Much of the work presented here is based on the morphologies of the mineral grains determined by the scanning electron microscope (SEM). The study concentrated on particles of 0.2 to 10.0 µm and on particles containing > 75% Si. Mechanically-crushed quartz particles were also examined for comparison purposes. Particle shapes from the airborne samples suggested that fractured quartz particles were rare. Particle statistics also show that the average size of quartz particles in the airborne samples were similar to the average size of all particles. The conclusion is that very few quartz particles from the source rocks are fractured during mining due to their small initial size and the protection of the associated clays.

Jan 1, 1991

By John Clarke Holman

Industrial growth and survival in today's competitive world means both economic efficiency and technological superiority. Superior technology includes not only exploiting the best methodologies and techniques presently available, but also a continuous search for and development of, better ones. In practical terms this translates into an investment of substantial sums of money. Of course, even a relatively small investment will not be justified if the fruits of the project cannot be secured to the investor and the inventor alike. There are at least three ways to protect new or improved technology. If the improvement reaches the height of an invention, "patenting" usually is the preferred mode of protection. If, however, the improvement is novel and valuable but does not satisfy the requirements of the patent laws, one may then consider "trade secret" agreements as a means of obtaining appropriate return for the investment made so long as the improvement is capable of being maintained in secret and cannot be "reverse engineered." If one develops a new and useful organism and seeks immediate protection from infringers, current thinking is that the copyright law may afford such protection simply by publishing the genetic code. Here is one instance where you may publish without perishing! This paper will endeavor to highlight the pros and cons of various legal mechanisms and their applicability to the frontiers of technology.

Jan 1, 1985

By Davidtz. John C.

INTRODUCTION The effectiveness of collector type on sulfide mineral flotation is generally determined by the amount and type of functional groups of collector molecules that interact with surface and water at the mineral/collector/water/gas interface. The final interfacial state when bubble contact takes place is preceded by chemical and physical reactions that involve these gas/liquid/solid interactions. These interactions differ not only for different minerals, solution and gas composition, but also for different collector molecules. The purpose of this paper is primarily to summarize the developments and status of short (C2-C6) and long (C12) chain, aliphatic collectors that contain three sulfur atoms in their polar function. These are trithiocarbonates (TT'Cs). For purposes of comparison, similarities in molecules containing 0, N and S are compared. Mostly short chain ionic collectors molecules of dithiocarbonates (DTCs) and TT'Cs were compared. The studies, largely bench scale flotation and plant testing, were carried out on ores containing Cu, Ni, Au, and PGM's. Studies of long chain 'ITC collectors are reported on Ni, PGM and auriferous pyrite ores containing uranium. Under starvation dosage conditions, surface activity coefficients of short chain collector molecules and interacting water were calculated. Based on the UNIFAC group contribution method of activity coefficient calculations, the Gibbs Excess Free Energy

Jan 1, 2005

By S. I. Nozhko, V. N. Guliy, A. A. Zolotarev, L. M. Luyshnia

The study of the apatite deposits of the Aldan Shield shows wide spread of the Precambrian apatite-carbonate ores and possibilities of using them for extraction of apatite. Dependency of flotation on ore minerals was studied according to the following scheme: preparation of the monomineralic samples of anhydrite, gypsum, chlorite, serpentine, phlogopite, apatite; mixing them in apatite ore of the average composition; followed by flotation. Another series of the experiments was conducted to ascertain a dependence of flotation activity of the different minerals on the different flotation reagents, which were used as collectors. It has been shown that apatite from silicate-carbonate ores is most extractable because it has the biggest size of grains and is the most free of inclusions. Beneficiation of the sulphate-containing apatite-carbonate rocks is possible when flotol - 7.9 is used as a collector. Meanwhile, the use of the tallaktam leads to an increase in the sulphate recovery. The estimation of individual technological features of the layered Mghydrosilicates and their influence on the process of beneficiation has been examined using samples of apatite-dolomite ore (P205-8%) with the addition of the phlogopite, serpentine and chlorite. The results show that there is little influence of the chlorite presence on the flotation while the serpentine presence leads to a decrease of the flotation, because of its high specific surface area.

Jan 1, 1993

By D. U. Deere, T. R. Harrell

Factors such as rock cover, rock type and rock quality can exert a dominate influence on the behavior of a concrete tunnel lining. This paper will present and discuss the investigation, evaluation and use of such factors at the Rocky Mountain Pumped Storage Project in the design of the 10.67m (35 foot) diameter concrete tunnel lining. A plane strain, finite element analysis was performed on the concrete/rock system. The finite element model consisted of a concrete lining zone and three (3) rock zones; a highly destressed rock zone, a transitional rock zone and an intact rock zone. Zones were differentiated from one another by varying the modulus for each zone. Results of this study yielded a concrete lining strain from radial expansion which was used in the crack control calculations for the concrete tunnel lining. After the tunnel excavation was performed, plate jacking tests and additional seismic surveys were run on the tunnel walls. This testing served to confirm the rock modulus values used in the preliminary analysis. However, results were observed which indicated that a two zone rock model would more accurately represent in-situ rock conditions than the three-zone rock model used in the preliminary analysis. This revision to the concrete/rock model was made and a final concrete tunnel lining analysis was performed.

Jan 1, 1986

By B. K. Mishra, R. K. Rajamani, P. Songfack

Primary grinding in SAG mills is gaining more importance with respect to the conventional crushing, rod and ball milling operations. This is due to the reduced operating costs generated by lower steel consumption. However. SAG milling is inherently susceptible to more severe risks and problems since it attempts to combine several stages of the conventional crushing and grinding into a single stage. This paper analyzes the SAG milling operation by predicting the motion of rocks and steel balls. The well-known discrete element method (DEM) is used to calculate the trajectories of individual entities, and their collision with one another. A computer code previously used for studying the motion of grinding media in ball mills is enhanced to handle the interaction between heavy spherical steel balls and light chunks of rocks, usually ellipsoidal in shape. The DEM based software called MILLSOFT can animate the charge motion for different design of liners. A case study of a 9.75-m diameter SAG mill is presented and the effects of lifter bar height and configuration on the overall dynamics of the charge are discussed. Also the effect of spacing between liners on lifting the charge is presented. This new approach has a large potential because it shows in detail the effect of each design or operating parameter on the performance of SAG mills.

Jan 1, 1998

By John D. Katsllometes

In the mining and processing industry, the maintenance plan has often evolved rather than being consciously set up resulting in an overreliance on breakdown and fixed-time maintenance (planned maintenance). Historically mining and processing plant equipment has been robust and less automated than modem equipment, making it relatively easy to work on. Mining and processing plants have relied on large and expensive maintenance departments to enable rapid attention to breakdowns. Maintenance itself can result in excessive downtime and costs. This results from the requirement to take the machinery off-line to carry out (possibly unnecessary and invasive) maintenance. The danger of infant mortality after it has been put back on line again and also the cost of the maintenance action itself contributes to costs. A goal of any well-run maintenance program is to have the lowest cost while providing 100% capacity 100% of the time to operations. When maintenance investments are at a minimum, the cost of lost production is at its highest. As maintenance effort and investments are intelligently increased, the production loss gradually decreases until the lowest combined cost is achieved. This is the maintenance goal. A road map is needed to achieving maintenance excellence. This article addresses a "Road Map" to achieving maintenance excellence. INTRODUCTION Mining and processing industry maintenance is big business. A world-class maintenance program is characterized by maintenance excellence.

Jan 1, 2004

By D. S. Young

The random variable transformation technique was introduced to make probabilistic structural analysis simple for such structures as slopes, dams, foundations, or retaining walls, where two shear strength parameters are required to analyze their stability by deterministic engineering methods. The Gaussian transformation was performed by using the Hermite orthogonal polynomial function. This transforms the experimental histogram into the standard normal distribution, whose mean is zero with a variance of one. Then, the transformed standard Gaussian variable was used for the bivariate normal probability analysis on the structure. The Gaussian transformation technique and the Hermite polynomial functions were chosen because the bivariate joint normal distribution is well-known and easily available for engineers. The binormal probability analysis was made on the probability region of a certain confidence level by superposing the critical line on the same probability region that divides the region into two zones: stable and unstable zones. The critical line was determined from the back calculation of the deterministic engineering method of the structural design. Finally, the probability of structural failure at a desired confidence level was calculated by simply integrating the volume of the binormal density surface above the unstable zone in the probability region. A simple case of slope analysis is introduced to illustrate this probabilistic approach, and its effectiveness and simplicity is demonstrated.

Jan 1, 1987

By Robert T. McKnight

Introduction The minerals exploration business, like many businesses, is faced with the problem of valuing future, risky cashflows. These cashflows are derived from those mineral deposits which have been successfully commercialized. Many deposits, however, do not have the quantities or grade of ore to be considered economic at the projected metal prices using the traditional tools of the Capital Asset Pricing Model and discounted cashflow analyses. If one calculates the future revenues, costs and cashflows of one these marginal properties, and discounted it at the appropriate risk-adjusted discount rate, it may have a negative present value. Yet such a property may still have real, positive value in the marketplace. Why would a firm pay money for a property with an (apparent) minus present value? Mining properties such as these are bought and sold in arms- length transactions on a regular basis. Why is this so? Part of the reason relates to the nature of ore reserve information. To generate cashflows, the analyst must t assume that the reserve information is known with certainty when, in fact, reserves are not known with certainty. Mineral reserves are a function of commodity price, extraction costs and the level of (usually drilling) information about the reserves. Stated, or currently known, mineral inventories may vastly understate the true state of nature. Some firms may therefore be buying a property based on a completely

Jan 1, 1988

By Glenn A. Hazen

Longwall mining is the preferred method for removing underground coal since a larger amount of coal can be removed faster and with less waste when compared to the room-and pillar type mining. Thus, the coal tonnage removed each year by longwall mining methods has increased dramatically. However, a high extraction rate results in surface subsidence which has adverse effects on the environment and on surface structures. Predictions of structural damage are dependent on the magnitude of the expected horizontal strains. Three methods for predicting subsidence characteristics are considered in this paper: the graphical method, the profile method, and the finite element method. All three methods can be used to predict ground movements and horizontal strains. However, the finite element method, which takes into account the structural properties of the stratigraphy and equilibrium of the overburden, is theoretically the more logical choice for use in subsidence prediction.

Jan 1, 1987

By M. M. Fine

One of the most persistent topics at technical gatherings and in the recent scientific press has been the reduction of iron ore. To cite some of them, in May 1960, a symposium on the subject was sponsored by the Electrochemical Society. The proceedings, comprising two dozen papers, were later published.3/ More recently, November 1966, a similar gathering took place at Michigan Technological University, Houghton, Mich. The latest meeting was the International Congress on Production and Utilization of Reduced Materials, Evian, France, May 1967. If the volume of literature, symposia and conferences is a measure of industry concern, then current interest must be at a high level. To the casual observer of the metallurgical scene, the abiding and recurring attention to iron ore reduction outside the blast furnace must be somewhat puzzling in that so much research endeavor has resulted in so little commercial activity.

Jan 1, 1968

By D. Panias

Alumina hydroxides such as gibbsite (Al(OH)3) and boehmite (AlOOH) are precursors of many types of alumina that find important industrial applications. The thermal decomposition of AlOOH, which is a more energy saving precursor compared to gibbsite, gives rise to the formation of ?-, d-, ?- and a-aluminas that are used for the production of catalysts. The applications of the aluminas are governed by their properties that are a function of the precursor material and its microstructure. The microstructure in turn is a factor of the method and conditions applied, as well as, in the case of soft chemical processes, on the anions present. Towards these ends, this study was focused on the effect of different anions on the physicochemical characteristics of the alumina hydroxides precipitated in the first 5 minutes after the perturbation of the stability of a supersaturated sodium aluminate solution (Bayer liquor).

Jan 1, 2006

By Terrence D. Chatwin, James Hendrix

Based on the findings within their report to Congress, the US Environmental Protection Agency (EPA) announced that it had decided not to regulate mining wastes under the hazardous waste regulatory program. However, they found that some mining wastes are hazardous and may be causing environmental damage. Cyanide wastes from heap leach operations were included in this group. In evaluating the effects of cyanide use in mining one finds a significant lack of information on the fate of cyanide in soils. Cyanide attenuation and degradation of soils is important, because ground water is a major potential pathway for cyanide contamination. There is a strong potential for cyanide to be removed from solutions as it migrates through soils· by volatilization, chemical reaction, adsorption, oxidation and biological processes, but no definitive investigation has defined these mechanisms adequately to be able to predict the fate of cyanide in soils.

Jan 1, 1998

By S. K. Vidyarthi

Most wastewater clean-up processes suffer from a fundamental lack of specificity in that a Reverse Osmosis process removes all dissolved solids, an Electrodialysis Reversal process removes all ions, wanted or unwanted, etc. Most techniques require the use of a membrane or contact surfaces that are prone to foul-up and are ineffective in situations where solids may be present. A photochemical process for the metallurgical industry on the other hand has the ability to operate specifically on targets that can range from one selected ion to an entire group of homologous species such as all biologically active species. Processes can be designed to change the oxidation states of a target altering the environmental impact. Several processes are currently in operation ranging from Cyanide removal to disposal of radiation wastes. This paper describes applicable photochemical processes with the help of certain key model examples.

Jan 1, 1988