Search Documents

By G. Zandt, H. R. Pratt, W. A. Hustrulid, M. Bouchon, D. E. Stephenson

PREFACE The National Waste Terminal Storage Program was initiated to conduct the research to select a site for the disposal of high level radioactive waste in deep geologic formations. As part of this program, the Savannah River Laboratory at Aiken, South Carolina, is conducting geologic research of generic applicability on the potential subsurface damage to a repository from an earthquake. Part of this study involved the collection of data on subsurface damage due to an earthquake, and another part involved the calculation of displacement fields as a result of an earthquake. Both of these studies were conducted at Terra Tek of Salt Lake City. This report is an abridged and combined version of both studies which was presented at the Rapid Excavation and Tunneling Conference in Atlanta, GA, on June 19, 1979.

Jan 1, 1979

All coal preparation unit operations in which fine coal is handled depend to some extent on wettability of coal surface by water. The wetting results from interactions between the coal surface and water molecules that are determined by the composition of coal matrix (interrelated with coal rank) and heterogeneous constituents such as oxygen functional groups, mineral impurities and pores. The contact angle of water on an unoxidized, homogeneous coal hydrocarbon matrix is calculated to be 100o, and much lower values measured on real coal specimens result from contributions from the heterogeneous constituents. While the effect of wettability is critical in flotation and oil agglomeration, suppression of respirable dust, and coal water fuels, it has been shown to play a significant role also in coal flocculation with semi-hydrophobic and totally hydrophobic flocculants.

Jan 1, 1995

By J. Pang, S. Chander

The mechanisms of chalcopyrite oxidation in alkaline solutions have been studied using cyclic voltammetry and impedance spectroscopy techniques. The cyclic voltammetry was used to elucidate oxidation/reduction reactions, whereas impedance spectroscopy was used for in-situ characterization of the interface. To analyze the impedance spectra, equivalent circuit models were constructed based on a layer- wise growth of reaction products. Parameters of the equivalent circuit were calculated by comparing the experimental spectrum with that expected on the basis of equivalent circuit. From the value of equivalent circuit parameters, properties of the surface layers were inferred. These properties change substantially with the change in oxygen and/or collector concentration in solution. From such changes the effect of oxygen and collector concentration on the contact angle and flotation behavior of chalcopyrite were interpreted.

Jan 1, 1991

By M. Z. Rashad, H. A. El-Sageer

This paper compares the covariance and multiquadric functions in some mining and geological applications. The basic principals of the two techniques are covered briefly. Similarities and dissimilarities of the covariance and multiquadric functions are discussed geometrically, mathematically and practically. A 14 km2 x 16 km2 area in Baharia Oasis, Western Desert of Egypt, was selected for a detailed comparative test. The gravity anomalies of 48 test stations were computed by using the data of 63 control stations. The results indicated that the covariance function is quite better than the multiquadric one. On the other hand, the multiquadric function is simpler in computation than the covariance, which requires precalculations such as semivariogram and covariogram. Moreover, multiquadric equations are based on geometric and physical considerations rather than covariance functions.

Jan 1, 1992

By A. W. Khair, J. A. Organiscak, M. Ahmad

This paper describes research that seas conducted on bit wear and respirable-dust generation. The investigation was performed by the US Bureau of Mines (USBM) and West Virginia University (WVU), a member of the Generic Technology Center on Respirable Dust. The USBM investigated wear, energy and dust characteristics of various conical bit designs when cutting rock. WVU studied the functional relationships between wear, cutting force, energy and dust of one type of conical bit cutting coal. The objective of the USBM study was to identify qualitative bit-selection guidelines. The objective of WVU's research was to determine optimum bit-replacement guidelines. Both research studies found that bit geometry (a function of bit design and wear) influences energy consumption and dust generation. Bit selection and replacement recommendations are given.

Jan 1, 1996

By I. de Jong, G. Van Weert

Silver cyanide adsorbs extremely well on activated carbons. This suggests that the addition of soluble silver salts to trace cyanide containing waste streams should allow efficient cyanide removal with active carbon. Silver losses, however, would make this method expensive and also objectionable, since silver has biocidal effects. When silver impregnated carbon is used, these problems are overcome. Test work has shown that such silver remains on or in the active carbon, that cyanide concentrations can be reduced to the level of detection (< 5 ppb) and that the silver impregnated carbon can be reactivated with equipment similar to that now in use at gold milling operations. Initial results on the type of carbon, the impregnation procedure and the level of silver, and the effect of repeated regeneration are discussed.

Jan 1, 1992

By A. R. Zambrano

Equations for power draft, capacity and work input for predicting the performance of industrial grinding mills are derived based on torque measurements using a laboratory instrumented mill. These derivations are based on mechanical principles and on the first-order kinetics of the grinding process. Rittinger&apos;s, Kick&apos;s and Bond&apos;s laws express work input as work index (Wi) times a particle size function. It is proposed that these laws are only particular cases of more general expressions having the particle size function raised to an exponent, i.e., the work exponent (We). Case studies illustrate the excellent prediction of the Wi - We models compared to the three mentioned laws, and, from the data, the corresponding general mill-sizing equation is derived. Key words: Grinding mills, Comminution, Work index, Mill sizing

Jan 1, 2003

By C. F. Bonney

Spherical or oil agglomeration has been recognised for many years as a possible process for the recovery of mineraVmetal values. BP has investigated the potential of spherical agglomeration for a number of minerals as have other workers. Testwork has also been carried out by both BP and others on the selective agglomeration of fine coal. The spherical agglomeration of both minerals and coal depends on the use of an immiscible liquid e.g. a hydrocarbon which is added to a suspension of the solids in water. On agitation the oil is distributed over oleophilic/hydrophobic surfaces and particle impact allows inter-particle liquid bridges to form causing agglomeration. It is also possible to enhance the oleophilicity of the material to be recovered by the use of collectors similar to those used in froth flotation.

Jan 1, 1998

By P. Riveros, A. Pratt, G. Deschênes

The effect of pyrite, pyrrhotite, chalcopyrite, realgar and arsenopyrite on gold dissolution in cyanide media was investigated. The cyanidation of synthetic gold ores, in the presence of various concentrations of sulphides, was studied under constant experimental conditions. A mineralogical analysis of the minerals was performed. The leaching kinetics were determined. The negative effect of sulphides on the gold dissolution rate varies with the sulphide mineral, and decreases according to the following order: realgar > pyrrhotite > chalcopyrite > pyrite > arsenopyrite. The chemical characterization of gold and sulphide minerals surfaces using X-ray photoelectron spectroscopy (XPS) was undertaken to identify the mechanisms involved. XPS analysis showed that a passivation layer of sulphides, arsenic or iron compounds may form on the gold surface as a result of the dissolution of the sulphide minerals.

Jan 1, 2002

By Kotaro Ohga, Gota DEGUCHI, Kiyoshi HGUCHI

The situation of Japanes coal mine is in the severe enviroment, because the policy on coal mining has changed. Every year one or two coal mines will be foced to close. To continue the production of coal, we have to reduce the cost of production. Therefore, the mining by longwall method which is more than 250m was attempted at Taiheiyou Coal Mine to reduce the cost and this mining method have had successful results. To get successful results by this mining method, the controlling and prediction of gas emission from the longwall panel will be most important things. In this paper, the comparison of the predicted gas emission from the mining panel based on the measured gas content by using new device with the observed results is described.

Jan 1, 1993

By C. L. Karr, E. J. Gentry

Researchers at the U. S. Bureau of Mines have developed a control algorithm to efficiently manipulate chaotic systems. The control, based on both fuzzy logic and genetic algorithms, prescribes actions that drive the chaotic system to acceptable regions of state space. The use of fuzzy logic enables a person who has limited experience with a chaotic system to establish a set of rules for manipulating the problem environment, and a set of membership functions that define terms used in the rule-set. Genetic algorithms are search algorithms based on natural genetics, and are used in the control algorithm to select membership functions that provide for a suitable level of control. The Bureau-developed algorithm controls the computer simulation of a ball bouncing on an oscillating table, a system that exhibits chaotic behavior.

Jan 1, 1993

By Greg P. Timms, John W. Bennett

Monitoring on Whites waste rock dump at Rum Jungle has provided a unique opportunity to assess the effectiveness of a cover in the medium term. Temperature and oxygen concentration profiles have been measured continuously, from some years before the cover was put in place in 1983 until the present. Lysimeters have been used to measure water infiltration rates. Heat and oxygen transport processes in the dump have been modelled and compared with field data, enabling oxidation rates to be quantified both before and after the cover was put in place. It has been found that the cover reduced the overall oxidation rate to between one third and one half of the uncovered rate. There is evidence that both the overall oxidation rate and water infiltration rate have increased in recent years.

Jan 1, 2000

By S. C. Bandis, N. Barton

During drilling of deep boreholes, local mechanical failures of the wellbore walls may occur due to the inability of the incompetent overburden and reservoir rocks to withstand drilling-induced changes of the stress environment. At present, borehole failure mechanisms in three-dimensional stress fields are poorly understood. Our experimental investigations based on 3-D physical models demonstrate the stabilizing effect of the intermediate principal stress. The latter may play a dominant role in maintaining the integrity of the stress relieving failure zone around the borehole. However, this will depend on the stress anisotropy, the angle of hole deviation and on the angle of internal friction. Our tests also indicate that the failure zone can accomodate high extensional strains. Finally, relations between the physical models and closed-form elasto-plastic solutions are discussed.

Jan 1, 1986

By Julie Mitchell

The U.S. Bureau of Mines is conducting research on the application of expert sys tens technology to mining equipment diagnostics and predictive maintenance, to increase mining productivity and efficiency. One of the greatest hindrances to mining productivity is the breakdown of equipment, causing lengthy and costly delays. A diagnostic maintenance expert system (DIMES) is being developed for the hydraulic system of a continuous coal mining machine. Through the use of such a system, the frequency of equipment failures and repair time should be significantly reduced. This paper describes the application domain, the functional requirements, and the problem approach for DIMES, the design and implement at i on of the knowledge- based system, the sensor work involved with the project, and the future plans for the continued development of this and other expert systems.

Jan 1, 1989

By S. M. Hsiung, Wen H. Su, Syd S. Peng

This paper examines the interaction problems of multiple seam mining by combining underground investigation, laboratory testings, and numerical modeling. One case of multiple seam interaction that occurred recently in West Virginia was carefully studied. Causes for the interaction problems were identified and the corresponding mining recommendations were proposed. The principle of pillar columnization and the effect of a remnant pillar on mining operations in the underlying and over- lying seams were also carefully examined. Considerable attention was given to the effect the pillar size, the pillar width, the coal stiffness, the extraction ratio, the degree of inhomogeneity in the interburden, the overburden thickness, the mechanical properties of the interburden rocks, the strata inclination, the interburden thickness, and the in-situ horizontal stresses have on the pillar load transfer mechanism.

Jan 1, 1986

By Ishwar G. Mulani

In conveyor design, the first step is capacity and the second step is belt width and speed. The third step is decision on &apos;ff," where distinction arises between DIN/ISO and CEMA for calculating resistances. Then again, both the methods are virtually similar. This topic helps in understanding Dm design style and its comparison to CEMA. This topic is from the book Engineering Science and Application Design for Belt Conveyor wherein the issue has been analysed in detail. It presents a workable calculation model to calculate the value off in design office, based on conveyor parameters. CEMA uses Kx, Ky and 0.01 5 instead off. Thus, f is a sum effect of Kx, Ky and 0.015. Hence, knowledge on f is also applicable to Kx and Ky. This helps to understand their relationship.

Jan 1, 2004

By K. H. E. Kroemer

Selecting persons who are unlikely to suffer an overexertion injury is one of three methods to reduce the risk of musculo-skeletal disorders in manual material handling. This paper describes the underlying models, methods, and techniques for such personnel selection. In particular, it describes the isoinertial LIFTEST in which persons actually lift weights to assess their capability for doing so on the job.

Jan 1, 1985

By Thys B. Johnson

This paper presents a new algorithm for solving the Controlled Flow Mine Ventilation Problem in an optimal manner - minimum power consumption. The use of booster fans and restrictions on the locations of ventilation regulators are dealt with in a straightforward manner. This new approach is based on a common Operations Research algorithm for which there are many fast computer programs available.

Jan 1, 1982

By Harry Holle, Ivan Hunter, Darrin Thomson, Gary Johnson

Over the past five years Dominion Mining Limited has directed an on-going effort towards optimising the performance of its milling circuits. The approach has been on a wide front, and has addressed a variety of issues associated with the design and operation of SAG milling circuits. Major projects have been conducted in the areas of flowsheet optimisation, mill liner efficiency, and dynamic circuit performance. As a result the initial designs of many of the Dominion circuits have been modified, mill liner specifications have been rationalised, and a robust automatic control system has been developed. A group-wide approach was taken on most of these projects, resulting in substantial benefits to both the individual operations and the company as a whole. By applying the projects group-wide a significant multiplier effect has been gained on the funds invested in each project. Extensive use of steady state modelling techniques has been made in order to understand the performance of the different circuits, and to highlight the potential areas in which improvements can be made. Liner optimisation has been primarily aimed at achieving predicability of performance, both metallurgical and mechanical. The development of a robust automatic control system has enabled the dynamics of the milling process to be controlled, and resulted in an additional increment in throughput being achieved. The combined effect of these efforts has been to raise plant availability to consistently over 95% (on a long term basis), to improve the power efficiency of comminution (in SAG mills) by 20% or more, and to enhance the dynamic performance such that a more than 10% increase circuit throughput has been demonstrated.

Jan 1, 1993

By M. J. McPherson, P. Mousset-Jones, J. Banik, F. Calizaya

Friction factors or coefficients of friction used to estimate the resistances of mine airways are, in the main, estimated from empirical measurements made in other airways considered to be of a similar geometry and type of lining. A somewhat more analytical approach, although still based on empiricism, is to estimate the ratio of the average height of the asperities to the hydraulic mean diameter of the airway (e/D ratio) and then to employ the Moody Chart or one of the equations that have long been established to represent the [coefficient of friction v Reynolds number curves] on that chart. Unfortunately, the Moody Chart and corresponding equations are based on pipes of uniformly distributed (sand grain) roughness whereas the asperities that exist on the surfaces of mine openings are frequently highly irregular both in their size and distribution. This is considered to be a major cause of discrepancies that have been found between coefficients of friction by the Moody Chart and those actually measured in mine airways. The work described in this paper examines an alternative method of estimating coefficients of friction for rough natural surfaces with uneven sizes and distribution of surface asperities. The technique utilizes the relatively recent developments in fractal analysis. A fractal dimension is determined from the topography of the surface. This has been correlated to coefficient of friction for a scale model of a mine airway. Further work is being carried out in actual mine airways. However, at this time, it appears promising that the fractal method may allow coefficient of friction to be predicted for given types of strata and method of roadway drivage.

Jan 1, 1993