Search Documents

By David D. Gallagher

Customer demand for greater efficiency and reduced operational costs on modern overland conveyors has focused attention on the conveyor belt's rolling resistance properties. Studies have indicated as much as 60% of the power losses on a long horizontal conveyor can be attributed to the indentation of the pulley cover rubber as it passes over idlers. This paper will compare tan delta values of different compounds with large scale rolling resistance test data from the University of Hannover. Results will then be compared to actual power consumption data gathered on several long overland conveyors using identical belt construction except with different pulley cover compounds. Concluding comments will be made indicating substantial operating cost differences based on the rolling resistance of the cover compound.

Jan 1, 2000

In April 2012, work started on one of the most ambitious construction projects of Austria?s ÖBB-Infrastruktur AG ? the New Semmering Base Tunnel. Scheduled for completion in 2024, the 27.3 km (17 mile) tunnel through the Semmering range will cut the journey time on the south railway connecting Lower Austria and Styria. Before con-struction can begin at the entrance portal and tunnel bores, the work concentrates on the above ground sections with the clearance and excavation of the entrance ramp site. The slope is currently being excavated by the Baubeteiligungsge-sellschaft m.b.H. BBG-GRAZ. The cut face is shored up with shotcrete and permanent self-drilling anchors produced by Minova MAI, an economical bolting solution for softer rock formations. After completing the surface construction work, the twin-bore, single-track tunnel will be cut through the Semmering by conventional and continuous excavation beginning in 2015. Once completed, the New Semmering Base Tunnel will be one of the longest rail tunnels in Austria. It will act as a vital link on the route crossing Europe?s heartland from Northern Germany to Italy, which currently has to climb the steep Semmering pass between Gloggnitz and Mürzzuschlag on a historic mountain railway recognized as one of the UNESCO World Heritage sites. The old route imposes considerable limitations on heavy freight trans-port, and passenger trains have to slow down to a speed of around 50 kph (31 mph). The New Semmering Base Tunnel will bypass this bottleneck and cut 30 minutes off the journey time between Vienna and Graz. It represents a particular advantage for freight traffic, since the new route?s minimal incline of 8.4 percent removes all obstacles for even heavy freight trains.

Jan 1, 2013

By Anna Marabini

This paper provides a summary of the studies performed over a period of more than fifteen years by the Italian National Research Council's Mineral Processing Institute in Rome to develop applications for the use of chelating reagents in the flotation of metallic minerals. A description is given of the various phases through which the studied progressed, starting with the combined use of commercial chelating reagents and a neutral oil and then moving on to the synthesis of new long-chain chelate collectors for the flotation of sulphide and oxidized Pb, Zn and Cu minerals. After a series of preliminary tests which confirmed the possibility of floating various metallic minerals with commercial reagents containing chelating groups exerting specific action on given cations, the studies were addressed to the development of a theoretical method of choosing chelating groups that exert selective action on one metallic mineral rather than others. The theoretical approach was based on thermodynamic data concerning the chemical equilibria in solution. The validity of the method has been proved in numerous cases by flotation tests on pure minerals. Subsequently the research was directed towards the design and synthesis of reagents with a mixed aliphatic-aromatic structure containing chelating groups for Pb and Zn and an alcoxyl chain of various length, position and configuration. The flotation results obtained on oxidized and mixed Zn-Pb ores provided interesting pointers for designing the nonpolar portion. The structural criteria identified via these studies were interpreted on the basis of chemical and steric considerations. A description is given of a new synthetic chelate collector which is effective in the selective flotation of Cu minerals from complex sulphides. The fact that this reagents is more selective than xanthate is demonstrated by comparative flotation tests on actual ores.

Jan 1, 1994

By S. Makni, C. Bazin, D. Hodouin

This paper reviews approaches for the real-time estimation of mass flow rates and assays using data from on-stream analyzers and flowmeters in a flotation circuit. Results obtained using one algorithm operating on-line with an industrial flotation circuit are presented.

Jan 1, 1998

By Chen Bingchen, Ma Shaojian

A new magnetic liner, with unique magnetic circuit and novel structure designs, was developed. It was characterized by light weight, low noise, as well as corrosive and abrasive resistance. The wear rate of the magnetic liner was one twentieth and one ninth those of the manganese-alloy steel and rubber ones respectively. The forming mechanism of the protective layer and that of influencing factors on magnetic liners were also investigated. The research results could not only instruct using magnetic liner, but also widen their application.

Jan 1, 1995

By P. Somasundaran, Bruno Lartiges

Two different groups of mechanisms have been considered in the past to explain the effects of chemical additives on grinding. While one group of explanations is based upon alterations of surface and mechanical properties of the individual particles, the other group depends mainly on the arrangement of particles and their flow in suspensions. In this paper some of the past work on grinding aids is reviewed and attrition grinding of a commercially important ceramic material, zirconia (stabilized with yttria) with polyaaylic acid as grinding aid, is studied in order to determine the effect of the aid on the ground product itself. It was observed that even though polyaaylic acid did cause a drastic decrease in the viscosity of the pulp, it did not have any major effect on the grinding of zirconia at least up to 2000 ppm and only minor detrimental effect above it. Importantly, complexation by the polymer was found to cause extraction of yttrium into solution with possibly significant changes in the surface chemical composition of the product.

Jan 1, 1992

By P. E. Richardson, N. P. Finkelstein, Z. Chen

The large band gap and insulating properties of sphalerite have limited the application of standard electrochemical techniques for studying its reactions with flotation reagents. This problem has been overcome by developing electrodes that rely on the surface conductance produced when sphalerite is activated with copper or other heavy metals. A brief exposure of the mineral in copper sulfate solutions results in electrodes that exhibit significant electrochemical activity characteristic of copper sulfides. Voltammetry studies conducted on sphalerite activated in 10-4 M CuS04, solutions at pH 4.6 provide information on both the amount and the nature of the activation product(s). It is shown that copper activation is strongly dependent on the electrochemical potential applied during activation. Activation at potentials increasingly negative of the rest potential causes a progressive increase in the amount of copper on the surface; activation at potentials positive of the rest potential decreases the amount of copper on the surface. The results indicate that both the kinetics of copper uptake and, possibly, the chemical composition (stoichiometry) of the activation product are controlled by the electrochemical potential.

Jan 1, 1995

By Willaim A. Berg

Vegetative stabilization can help meet the esthetic objections and pollution problems posed by mine wastes. However, mine wastes are often unfavorable growth media and special treatments and techniques are needed for plant establishment and continued growth. The establishment of vegetation on mine wastes was the subject of many papers presented at the International Symposium on Ecology and Revegetation of Drastically Disturbed Areas held at Pennsylvania State University on August 3-16, 1969. This paper is a summary of those papers presented at the symposium that dealt with the nutritional and physical aspects of plant establishment on a variety of mine wastes. The synopsis presented is a combination of excerpts from the abstracts, notes on the oral presentations, and rough drafts of some of the papers. The papers will eventually be published in the symposium proceedings.

Jan 1, 1970

By C. I. Basilio

The adsorption of O-isopropyl-N-ethylthionocarbamate (IPETC) and O-isobutyl-N-ethoxycarbonylthionocarbamate (IBECTC) on chalcocite, chalcopyrite and pyrite has been studied using UV and in-situ FTIR~ATR spectroscopy. Thionocarbamates were found -to adsorb strongly on chalcocite at pH 4-10, but consider-ably less on chalcopyrite and pyrite. The FTIR spectra show that the surface species of thiono-carbamates are bonded to metal atoms on the mineral surfaces. However, at high concentrations, IBECTC also forms physically-adsorbed species. Adsorption of these thionocarbamates cannot remove or prevent the formation of sulfoxy oxidation products on pyrite, unlike the case with the xanthate-pyrite system. This finding may account for the observed flotation selectivity of these reagents against pyrite. The spectroscopic information is compared with flotation test results.

Jan 1, 1988

By L. F. Nicolai, W. J. Schlitt

Lateral migration of leach solution in heaps and dumps is attributed to two phenomena. One is site-specific anisotropic conditions that exist on a macroscopic scale on the surface or within the rock piles. The second is associated with a random walk phenomenon that causes dispersion of solution, especially at gradients in flow or hydrostatic pressure. The latter phenomenon is a general condition that will occur in any leaching operation. Its effects are modeled by computer analysis and are compared with available field data on heap leaching. Under appropriate assumptions, the observed 58° angle of solution dispersion can be reproduced by the model. The combined effects of both anisotropy and random walk are also discussed. Finally, the impact of lateral solution flow on actual leaching operations is considered.

Jan 1, 1988

By Jerry C. Tien

An overcast is a form of air bridge which permits one air current to pass another without mixing. It is an essential and indispensable ventilation device for underground air distribution in horizontal mineral deposits. Overcasts are also a major source of shock pressure loss under- ground. However, a well thought out overcast plan, and a well constructed overcast, will give minimum shock loss, which in turn can save money (Tien, 1986). So far, most research on shock losses has been concentrated on splits and junctions, and bends and turns, or on underground regulators. Practically nothing could be found in the literature regarding losses caused by overcasts (see reference on shock losses). In this investigation, shock losses are quantified for an overcast with different configurations, which will give useful clues toward an aerodynamically designed overcast.

Jan 1, 1987

By R. D. Hansen, R. R. Klimpel

This paper discusses the influence of frother type and dosage on recovery/selectivity in coal/sulfide mineral flotation as a function of particle size. It is shown that different frother structures exhibit quite different but consistent performance characteristics depending on the underlying particle size ranges involved as well as the dosage levels of both the frother and collector. The data presented on existing commercial frothers and some new special purpose experimental frothers is used to illustrate some general operator guidelines on proper frother selection and use.

Jan 1, 1987

By Erich U. Petersen, J. B. Hiskey, William J. Tafuri, Donald M. Hausen, X. H. Jiang, Douglas N. Halbe, G. Ramadorai

The extraction of gold from chloride solutions with activated carbon is examined. It is shown that the uptake of gold by activated carbon from chloride solution follows a mechanism whereby gold is reduced to the metallic state. Metallic gold appears as deposits both on the carbon surface and in pore space within the carbon particle. The deposition rate is dependant on the carbon particle size and pH. At low initial gold concentrations, the initial rate is insensitive to gold concentration. Sodium hypochlorite exhibits an adverse effect on the reduction reaction. The overall loading and initial rate of reduction are both decreased in the presence of NaC10. The effect of iodide on the loading of gold was also examined in an attempt to overcome the superficial deposition of gold on carbon.

Jan 1, 1990

By Peter J. Stewart

My first experience with carbon reactivation in the gold industry was at Whim Creek, Meekatharra some 15 years ago. Very little was known, in fact, carbon reactivation kilns in the gold room were a complete mystery. Ten years ago at conferences such as this the mystery was more as to why field kilns would not reproduce activities achieved in the laboratory. A carbon reactivation kiln manufac­turer was thought to be brave or stupid to speak at a venue such as this. Reactivation kiln design has improved dramatically in the past 10 years and with a few exceptions, most kilns operate well. May I suggest that now, the focus is on plant practice rather than kiln design, and that the basics of plant practice as it relates to carbon activity needs revisiting. As metallurgists like to talk on engineering, accountants on the Economy and vice versa, my presentation on Carbon Reactivation will focus on plant design and operation as it effects carbon reactivation. There have been some excellent papers published over the past 15 years on the basics of carbon reactivation in relation to gold processingl,2,}. Taken that kilns operate and are effective to a greater or lesser degree, plant design and operating practise have an enormous bearing on carbon activity, solution tail, carbon loss and other cost items. This presentation will not argue the merits of equipment used for the thermal reactivation of organically fouled carbon, questions on this subject are welcome over a drink after this session.

Jan 1, 1995

Surface contamination of minerals during fine grinding may occur due to coating of one material on the other. This can alter the surface chemical properties and adversely affect the separation of minerals by physico-chemical processes. In dolomite-silica system, selectivity was completely lost (compared to a synthetic mixture) after wet grinding of the minerals in spite of using a dispersant. Adsorption and surface characterization studies were conducted on silica particles separated after grinding with dolomite. SEM-EDAX analysis indicated the presence of dolomite on silica particles, which could cause the loss of selectivity.

Jan 1, 1993

By Harry Sutcliffe, Francis M. Keville

The paper describes the, impact of the geotechnical exploration program on the line and grade of the tunnels and the shaft configuration on the Red Line Extension N.W. in Cambridge and Somerville, Massachusetts, and comments on several aspects of the implementation of the project.

Jan 1, 1983

By J. Brinen, D. R. Nagaraj

Secondary Ion Mass Spectroscopy (SIMS) was used to study copper ion adsorption, and its effect on subsequent sulfide collector adsorption, on pyrite and pyroxene minerals under flotation related conditions. Copper was found to adsorb on both of these minerals and cause enhanced sulfide collector adsorption. The distribution and depth profile of copper and collector on these mineral surfaces were obtained by using SIMS in the imaging mode. The results of this study have provided a valuable insight to understanding pyrite and gangue flotation observed frequently in operating plants.

Jan 1, 1995

By T. Seal

The Hydro-Jex technology has been used by Newmont Mining Corp. on the gold heap leach pads on the Carlin Trend - Nevada for three years to recover the inventory gold and change the chemistry in the pads. This research and development patented process is complete with the resultant data presented. Information on drill sampling, geophysical surveying, followed by leach pad stimulation with impacts on solution chemistry and gold recovery are discussed. Can this technology be used to rinse and close heap leach pads faster with reduced pump energy costs and improved recovery?

Jan 1, 2007

By L. D. Gehi, A. W. Khair, M. Ahmad

This paper presents an analysis of the effect of the dynamics of bit wear on dust generation. Two surveys have been conducted in order to assess the mechanism and type of bit wear and to evaluate the impact of bit wear on the productivity of the continuous miners. Used bits were collected from the underground coal mines and these used bits were utilized in laboratory coal cutting. The effect of bit wear on dust generation has been quantified and its impacted on dust generation and ventilation system has been exemplified.

Jan 1, 1993

A one-day seminar designed to help quarry and mining managers make their operations more productive, more efficient and less expensive was held in Harris- burg PA. "Rock-Solid Productivity" was sponsored by Pittsburgh Power & Light (PP&L). The seminar, one of a series sponsored by PP&L in 1997, proved to be well-organized and provided valuable information to the many quarry and mining professionals who attended. The information presented included a comparison of on-site diesel power vs. electric power, discussions of equipment improvements and topics on environmental management.

Jan 1, 1998