Search Documents

By C. J. Badenhorst

Oxides of sulphur are corrosive and are produced when sulphur-containing fuels are burned. Sulphur dioxide (SO2) is a colourless gas with a characteristic, irritating, pungent odour. Exposure routes to the human body are mainly through inhalation and skin and/or eye contact. Symptoms of exposure to SO2 may include irritation of the eyes, nose, and throat; rhinorrhea (discharge of thin nasal mucous); choking; cough; and reflex bronchoconstriction. To protect employees against the ill health effects of SO2 exposure, they are often required to make use of respiratory protection whenever entering areas were the SO2 levels exceed the statutory limits. The use of respiratory protective equipment should always be a last resort and should be considered only after other control measures have failed to reduce occupational exposure levels to below the occupational exposure limit or whilst other control measures are being investigated or implemented. Whenever the use of respiratory protection equipment is considered, it should always be used as part of a comprehensive respiratory protection plan. It is also extremely important that all potentially exposed persons are adequately and comprehensively informed and trained.

Jan 1, 2007

By L. Morgan, M. Le Roux, Q. P. Campbell

Dry coal processing is becoming increasingly favoured as a fine coal beneficiation technique. The decline in suitable good-quality coal, as well as the ongoing decrease in usable process water, makes dry beneficiation of the fine coal fraction even more crucial. Dry fine coal beneficiation is a relatively young process with most of the methods still in the developmental phase. Additionally, many of the dry processing options available are better suited for coarser (+6 mm) and easy-to-beneficiate coal. Air winnowing for fine particles has been established in both agricultural and pharmaceutical industries, which indicates that the method can be used to separate smaller particles on a density basis and therefore, may prove effective in the coal industry as well. A proof of concept study was conducted using both computer-based simulations (which do not form part of this paper) and physical experiments. The initial winnowing unit consisted of a closed box with a horizontal air stream flowing through the top section. Coal particles were injected into the air stream and displaced horizontally across a distance (x), depending on the particle size and density, thus actuating a separation based on these two parameters. For this study particle sizes of 6, 4 and 2 mm were used all with a density ranging from 1200 kg·m-3 to 2000 kg·m-3. The simulation in Star CCM+ confirmed the findings of the mathematic behavioural model and provided a virtual representation of the separation using streamlines and particle tracks. The coal tests prove that size separation can be achieved at an airflow velocity of 21 m·s-1 and the density cut-point can also be predicted by using the prediction matrices constructed as part of this study. The results show efficiency values (EPM) of 0.11 and 0.09 at density cut-points of 1400 kg·m-3 and 1500 kg·m-3 respectively. The data obtained from the study indicates that air winnowing can be used to separate fine coal particles based on both size and density. However, in order to achieve an efficient density separation, a narrow size range is required. With some improvements to the model, simulation, method and design, the separation efficiency can also be improved. The next phase of testing will include the upscaling of the process to a demonstration plant, optimising the separation unit and testing the method on different qualities of coal. Keywords: Dry processing, fine coal, winnowing, simulation, tracers, demonstration plant

Jan 1, 2020

By S. O. Choi, H. -S. Shin, W. -K. Song

Nuclear waste should be disposed with the best warranty for the national health and welfare. Among the several repository systems, the deep underground disposal is considered to be a most suitable system in Korean peninsula. However it demands basically the comprehensive stability analysis such as the behaviour of discontinuities in rock mass, the behaviour of ground water, and the reaction of rock stress according to the heat from the nuclear waste. For these purposes, the underground nuclear waste disposal repository was simulated in two- and three- dimensions. It shows that emphasis will be given to the thermal conductivity of discontinuities and the thermal convection of ground water as well as the thermal stress generated by the nuclear waste for design and construction of repository system, and they should be obtained from the field measurements. Déchets nucléaires devront tre déposés avec la meilleure garantie pour la santé et le bien public. Parmi les plusieurs systèmes de dépôt, la disposition en souterrin profond est considérée au système le plus approprié en Corée. Pourtant ce système demande essentiellement l’analyse éten-due de stabilité comme le comportement des discontinues en masse rocheuse, le comportement de l’eau souterrin et la réaction des contraintes de roche selon la chaleur depuis les déchets nucléaires. Pour ce but, le dépôt des déchets nucléaires en sous-sol a étè simulé en deux et trois dimensions. Il montre que l’accent sera donné à la conductivité thermale des discontinues et la convection thermale de l’eau souterrin aussi bien que la contrainte thermale générée par les déchets nucléaires pour le plan et la construction du systèmes de dépôt, et ils devront tre obtenus depuis les mesures sur place. Die Kernwüste muß mit der besten Gewähr für die nationale Gesundheit und die Wohlfahrt angeordnenet werden. Unter einigem Fundgrubesystem, das tief unterirdisch Wegwerfen werde in Betracht das passendest System in der koreanisch Halbinsel gezogen. Jedoch, es verlangt grundzätzlich die umfassend Stabilitätsberechnung so wie das Behnehmen mangelnder Konti-nuität in der Felsmasse, das Behnehmen des Grundwasser, und die Reaktion der Felsenbelastung nach der Hitze von der Kernwüste. Für diesen Zwecke, die unterirdische Wegferfenfundgrube der Kernwüste wurde in der zwei und drei Dimensionen gesimuliert. Es beweist daß die Betonung wird zur thermisch Leitfähigkeit mangelnder Kontinuität und thermisch Konvektion des Grund-wasser sowie die thermisch Belastung ergezeugt durch die Kernwüste für den Entwurf und die Konstruktion des Fundgrubesystem gegeben werden, und sie müssen von den Feldmaße ergelangt werden .

Jan 1, 2003

By M. J. Voigt, R. A. Govender, A. Mainza, L. Bbosa

"Mineral texture is a critical factor which controls ore variability and is an important attribute in geometallurgy. In relation to downstream processes, it affects the fracture pattern during breakage, where rock strength is inherently a function of mineral texture. Because of the subjective nature of mineral texture, it has not been easy to quantify, especially in the context of a measurement suitable for use in geometallurgical programmes. The aim of this paper is to present the first steps in developing a 3D mineral texture quantification method for drill core and to assess its sensitivity to differences in rock strength using a case study. The methodology includes classifying the textural information using the 3D grey level co-occurrence matrices (GLCM) and X-ray computed tomography (XCT) coupled method. Rock strength tests were performed using the split Hopkinson pressure bar (SHPB). The case study investigates a heterogeneous polymetallic sulphide deposit and a homogeneous shale subdivided into three ’mineral textural types’. The variability is largely captured by the GLCM matrices, and preliminary trends can be observed where the shale is finer grained and has a higher yield strength in comparison with the coarser grained polymetallic sulphide ore. IntroductionModern mining requires the exploitation of lower grade and more complex, heterogeneous orebodies to address the growing industry demands. Historically, processing plants were designed and built based on average ore characteristics and therefore are relatively inflexible when facing the full spectrum of ore variability in heterogeneous orebodies (Lamberg, 2011; Lotter, 2011; Schouwstra et al., 2013). The practice of geometallurgy represents an opportunity to manage ore variability in the mining industry (Powell 2013; Baum, 2014; Yildirim et al., 2014; Nguyen, 2013). It focuses on quantifying the relationships between ore characteristics and their downstream mining and processing responses, often starting with small-scale laboratory testing. The purpose of geometallurgy is linked to maximizing the net present value (NPV) of an orebody by minimizing technical and operational risk – where ‘ore variability’ is considered one of the most significant technical risks."

Apr 1, 2019

By P M. Bradbury

The nature of aggressive process chemical requirements typically in the Platinum Refinery Industries, lend themselves to the use of Polymer Composite Glass Reinforced plastics for pipework and other associated equipment in these types of Plants. This paper discusses the basic characteristics of a Polymer Composite glass reinforced piping system and gives sample examples of applications in current present day use.

Jan 1, 2006

By N. F. Mescheriakov

New mechanical and pneumatic-mechanical flotation machines with axial impellers have been developed. Industrial tests show that these machines ensure lower power expenditure (on flotation) by 1.5-2.0 times as compared with reference machines (with the same or improved technological indices). Application of the newly developed axial impeller, with these advantages, is possible in any volume chambers of type OK, Dorr-Oliver, Wemko etc.

Jan 1, 1998

By A. A. Debrah

Artisanal and small-scale mining (ASM) plays a fundamental role in the national and local economies of resource-rich countries in Africa. As such, more effort must be geared towards fostering this type of economic activity to sustain livelihoods in rural communities. Across Africa, efforts to operationalize ASM based on a sustainable development framework have been quite tedious and often ineffective. This is because most of these frameworks lacked context and an understanding of the continuum from the artisanal through small-scale and up to the junior miner, grouped under the general term ?ASM?. Driven by the need to contextualize some of the definitional issues in this niche sector, and gain a clearer understanding of their peculiar challenges, this paper aims to contribute to the debate on ASM by considering two of Africa?s resource-rich countries ? Ghana and South Africa. Since South Africa has made greater inroads in protecting the interests of small-scale miners, we thus draw comparisons from both countries? approach to ASM, outline the lessons learnt, and provide recommendations regarding the ways forward.

Jan 1, 2014

By M. Shapiro, L. A. le Grange, B. Henning

A paper was presented by Bateman Minerals and Metals at INFACONX (2004) describing a simplified Computational Fluid Dynamics (CFD) Model for predicting the temperature and velocity distributions in all the fluid zones of a single electrode DC Furnace simultaneously with the temperature distributions in the refractory lining of the vessel. The boundary conditions imposed on the model consisted of the arc current, external surface film coefficients and ambient temperatures. The temperature and velocity distributions in the free-board, slag and metal were solved simultaneously by coupling across the interfaces between the fluids and transportation phenomena developing in the plasma arc. A simplified model was used to describe the ex-change of energy by radiation between the arc and surfaces enclosing the freeboard region. The strengths of this model were reported as being the ability to: ?Solve the different zones and transportation phenomena simultaneously without the need to transfer partial numerical results between different numerical analysis applications. ?Solve velocity and temperature distributions without assumptions regarding internal film coefficients and additional internal temperature boundary conditions. One of the disadvantages of the model was that the energy absorbed by the process was not modelled, resulting in vessel performance predictions under heat loss conditions only. Whilst this allowed potential problem areas such as localized refractory heating to be identified, the model was only capable of predicting how these could be improved by varying the overall geometry and materials of construction. This paper presents improvements in the application software and user defined subroutines of the model as follows: ?Incorporation of surface to gas, gas to gas and gas to surface radiation models to improve the accuracy of radiative heat transfer mechanisms within the freeboard. ?Incorporation of a process energy absorption model based on a theoretical temperature dependant enthalpy curve which incorporates melting, smelting and superheating in selected areas of the bath. This enables the effect of feed distribution and power to feed ratio changes to be estimated. The effects of a commercial arc at full power on the freeboard and slag can now be simulated with increased accuracy.

Jan 1, 2007

By M. D. Lionnet

The Bafokeng Rasimone Platinum Mine (BRPM) is a joint venture between Rustenburg Platinum Mines Limited and Royal Bafokeng Resources (Pty) Ltd (Bafokeng). The mining lease has been granted over Boschkoppie 104JQ and is located approximately 10 km south of the Pilanesberg Alkaline Complex. The Merensky Reef, which constitutes the principal orebody, is geologically complex. A relationship between its geological variability and the associated mineralization has been established by defining a number of facies types. The Merensky Reef has been subdivided into seven distinct facies types: the pegmatoidal facies, contact facies, FW1 potholefacies, FW3 pothole facies, FW6 pothole facies, and FW7 pothole facies. The Merensky Reef, which does not form part of the potholed reef, has a large component of footwall mineralization. The pothole facies, in contrast, has mineralization located in the hangingwall. Statistical analysis of the facies types indicates that they are unique populations and hence need to be evaluated independently. The mining lease has distinct structural domains that have added additional complications to evaluation of the Merensky Reef. The Merensky facies on BRPM exhibit unique geological and statistical characteristics within well-defined structural blocks. Due to the extreme variability of the Merensky Reef on BRPM a unique approach has been developed, within Anglo Platinum, to evaluate the deposit. Mining cuts are defined and composited for the individual facies types, and then modelled individually by applying known geological controls. The resultant grade models are weighted based on statistical and local geological knowledge. The object of weighting the facies is to replicate the variability observed in the orebody. The introduction of stringent geological controls to the evaluation process has resulted in increased confidence in the in situ grades estimated as an input to the mine planning process.

Jan 1, 2007

By A. Sandberg, M. Nzotta, Du Sichen, N. N. Tripathi, K. Beskow

The present study was carried out to investigate the impact of slag refractory lining reactions on the formation of inclusions during ladle treatment of steel. The experiments were conducted on an industrial scale in the ladle at Uddeholm Tooling AB in Hagfors, Sweden. The inclusion chemistry and population during ladle treatment were studied along with the composition of the ladle glaze, taken from the ladle lining. The inclusions in the steel were classified into four groups according to the Swedish standard SS 111116. SEM/EDS analyses were carried out to identify the phases present in both the inclusions and the ladle glaze. The number of inclusions in the steel before deoxidation was found to increase with the ladle age, i.e. the number of times the ladle had been in use. A similar increase was also found after vacuum degassing and before casting. A great portion of inclusions before casting was found to be supplied by ladle glaze. This observation was further confirmed and explained by thermodynamic analysis. The present results show that ladle glaze is a major source of inclusions in the ladle at Uddeholm Tooling. Keywords: Slag/ refractory/ lining?reactions, ladle glaze, inclusions, inclusion chemistry, ladle treatment

Jan 1, 2004

By B. Ulrich

The basis of this paper is a compilation of work in the design and construction of copper heap leach facilities, and interviews with various heap leach operations personnel in Chile and Peru. The purpose is not to highlight specific mines and their performance, but rather to discuss geotechnical/civil features of copper heap leach facilities that function well, as well as features that do not. During the 1990s several copper heap leach facilities were brought on-line in South America. Many of these facilities have now been operational for a number of years during which time the operators have been able to monitor the performance of their heaps. This paper serves as a compilation of operators? experiences, and provides a discussion of the lessons learnt over the past decade. Several key geotechnical issues are examined, focusing upon the integrity of the ore, drainage material and pipe network, along with the success of inter-lift liners. This conference provides a timely update of the original paper (Burkhalter et al, 2002).

Jan 1, 2003

By Christian Roche

Our study is focused on the sub-assembly con-tact shoes, pressure rings and pressure bellows. We were keen to mainly study [ ] 1.The contact shoe design 2.The most efficient pressure to ensure an optimal electrical contact between the contact pad itself and the casing 3. The contact shoe cooling circuit in view to provide to the shoe the best mechanical and electrical characteristics in order to bring to the users of COFOR® components a new standard in process setting technical solutions. A finite elements simulation, combined with a thermal and structural studies were used. Our presentation which follows is dedicated exclusively on the influence of the contact shoe cooling system on the process through a thermal and structural analysis. [ ]

Jan 1, 2007

By P. N. Vernon

Ausmelt top entry submerged lance technology offers a cost-effective means of carrying out a range of base metal smelting operations with minimum impact on the environment. The system is capable of using a range of fuels depending upon local costs. Due to the intense, localised reaction zone, high energy efficiency is obtained and the physical size of the plant is relatively small compared to that of most competing technologies. Capital cost can thereby be minimised. The furnace is well enclosed, such that fugitive emissions and ingress of diluting air to the gas stream are both minimised. The oxygen potential in the slag can be varied over a wide range such that the system can be applied in both oxidising and reducing duties. Following a general description of the technology, the paper discusses Ausmelt plants already in operation. The application of the technology for the provision of additional smelting capacity, for the improvement of converting operations and for slag cleaning is then described. A brief explanation of how these processes could be applied at southern African smelters is given and the paper closes with an assessment of novel Ausmelt applications for this geographical region, such as zinc recovery from sulphides.

Jan 1, 1997

By C. Sima, M. Legoabe

Keywords: Pyrometallurgy, furnace, platinum Mortimer Smelter is one of the three smelting operations in the Anglo Platinum Group. It is located in the Limpopo Province, approximately 100 km north of Rustenburg, and approximately 15 km west of Northam. The smelter operation is the smallest of the three smelting operations in the group, with a smelting capacity of 170 kt/annum. The operation consists of a Larox filtration plant, a Drytech flash drying plant, a modified Elkem / Hatch 19.5 MVA furnace, and a 60 t/h matte crushing plant. The operation does not convert its furnace matte, and hence the final sulphide rich matte is transported to and processed further at the Anglo Platinum Converting Process (ACP) within the Waterval Smelter Complex in Rustenburg. Furnace slag is granulated, and processed through a slag mill, or transported to a slag dump.

Jan 1, 2006

By M. Matema

Paper written on project work carried out in partial fulfilment of BSc (Eng.) Metallurgy and Materials Engineering Small and large welded aluminium specimens were tested in fatigue and the results compared with design curves for aluminium in specification BS8118. Metallurgical tests were also performed on the specimens in order to correlate microscopic and macroscopic phenomena. The small-scale fatigue test results were in reasonable agreement with results in BS8118, whereas the large-scale fatigue tests showed that BS8118 is conservative.

Jan 1, 2005

By A. B. Fox, R. P. Thackray, K. C. Mills

The role of mould fluxes in continuous casting is reviewed. The main functions of the flux are described and the importance of the flux in providing lubrication and the right level of heat transfer between the shell and the mould is described. The major problems of longitudinal, transverse and star cracking, gas and slag entrapment and deep oscillation marks in the steel product and ?sticker breakouts? are analysed. The important physical properties of the flux in combating these various problems are identified. Physical property data for the fluxes are given.

Jan 1, 2004

By J. N. Van der Merwe

The current state of the South African mining industry is briefly reviewed from the point of view of an engineer not schooled in the finer details of predictive economics. Based on the assumption that current world exploration targets are indicative of which commodities the world will want in the future, it is concluded that the South African mining industry will continue to be viable and growing well into the future. South Africa holds the minerals the world wants and needs, and as long as the world has people, the demand for those, including gold, will continue to grow. There still is a growing demand for vanity commodities' and even the demand for platinum as a jewellery material displays significant growth. Mine safety still needs to improve, but significant improvement has already been made although the industry is not always acknowledged for the effort in this field. The safety target set for 2013 is within reach but will require sustained effort. The physical mining conditions for the main revenue earners, coal, platinum, and gold, will change substantially in the near future. Research in mining has declined alarmingly and it is urgently necessary for that to be revitalized to generate the knowledge that will be required. In order to streamline the transfer of knowledge to the mining engineers of the future, research needs to be conducted with the full involvement of the universities. It will also be necessary for the universities to continually review curricula to incorporate the latest knowledge and to embark on a campaign of knowledge transfer to the older generation of mining engineers. The mining industry is well supported by the universities, who have done their duty with regard to societal transformation, and the universities are in turn supported by the industry through vehicles like the METE Industry is also strongly supported by a number of professional and vocational societies. The SAIMM will continue to play its vital role as the meeting point of the mining technical sciences, and will continue to disseminate knowledge via the journal, schools, and conferences. In the future, it will review its modus operandi to support the needs of growing membership in the remote branches. It will enter the research arena in an appropriate manner and give effect to the developing integration of mining and society. The most important threat to the future of the mining industry is the recurrent mention of nationalization. While interaction between the mining industry and political and economic development of South Africa has always been characteristic, the current debate is emotional more than rational, and engineers are not well equipped to participate. This matter needs to be finalized before it becomes a popular force that politicians cannot control.

Jan 1, 2011

The Mineral Density Separator (MDS) was developed by Mintek to predict mineral separation in a plant, evaluate efficiencies and develop scale-up parameters. This study investigated the influence of particle size on the results of the MDS, the misplacement of material in the MDS and the possibility of replacing heavy liquid float and sink analyses of coal with MDS analyses. Six tests were done with coal of different size ranges. Each MDS layer was subjected to a float-sink analysis whereafter each float fraction was screened to determine the particle size distribution. The results indicated that MDS results represent float-sink analyses when compared to an ash curve. There is some misplacement in the different MDS layers, but this does not seem to influence the results negatively. Keywords Mineral density separator, sink-float analyses, heavy liquid analyses, washability curve

Jan 1, 2006

By R. Dass

Paper written on project work carried out in partial fulfilment of B. Sc Eng (Extractive Metallurgy) degree Screening is an industrial process that splits material at a specific cut size into one fraction of particles larger than the cut size and another fraction of particles smaller than the cut size. Particles are vibrated to increase the probability of them being accurately classified and to move the oversize particles off the screen surface. In conventional screening, the screen mesh vibrates with a single frequency and the particles on the screen are all exposed to this same frequency. The Ultimate Screener (see Figure 1) is a new screen technology that imparts multi-frequency vibrations to the screen mesh so that different parts of the screen surface vibrate at different frequencies. The Ultimate Screener incorporates an additional deck that holds the multi frequency adapters as shown by Figure 2. These special adapters can transform single frequency vibrations into multi frequency vibrations. When the screen motors are switched on they begin to vibrate. This vibration is transmitted to the adapters via the body of the machine. The adapters then modify the vibration to have multiple frequencies, which are transmitted to the screen surface via resonating rings.

Jan 1, 2004

By P. Amponsah-Mensah

Dilution of ore has a major impact on economics of a mine. The magnitude of dilution depends on mining method, stope dimensions, reef and host rock quality, wall support and drilling accuracy. The main contributing factor is the presence of very weak graphitic shear band of varying thickness in and around the reef. The reef, at Obuasi, is generally steeply dipping and open stoping is the predominant mining method. The stability of the stope walls limits the stope dimensions. Various options for allowing larger stopes for higher productivity and limiting dilution are analysed. The most economic way is to reinforce the walls with systematic cablebolt supports. This option does not only add the support cost but also requires additional cost of access development. These conflicting requirements are continually being optimised at the mine for the economics of dilution control. La dilution du minerai à un impact majeure sur l’économie d’une mine. La quantité de matériel diluant le minerai dépend de la méthode d’extraction, de la dimension des chantiers d’abattage, de la qualité du filon et de la roche mère, du support des épontes et de la précision du forage de production. Le facteur principal qui contribue à la dilution est la présence d’étroites zones cisaillées qui contiennent du graphite ayant différentes épaisseurs à l’intérieur et autour du filon. Le filon, à Obuasi, est généralement à fort pendage et la méthode d’abattage principale est par chantier long-trous. La stabilité des épontes est le facteur qui détermine la dimension des chantiers d’abattage. Differentes options ont été analysées de façon à permettre de plus larges chantiers de manière à augmenter la productivité tout en limitant la dilution. Le moyen le plus économique est de renforcer les épontes avec des cables d’acier cimentés forés de façon systématiques. Cette option n’augmente pas seulement les coûts de support mais aussi les coûts de développement. Ces besoins contradictoires sont continuellement revisés à l’opération afin d’optimiser l’économique par le contrôle de la dilution. Verdünnung des Erzes hat eine spürbare Auswirkung auf die Ekonomie einer Grube. Die Größe der Verdünnung hängt von gewinnenmethode, von den Stopemaßen, von der Reef- und Wirtsfelsenqualität, von der Wandunterstützung und von der bohrengenauigkeit ab. Der beitragende Hauptfaktor ist das Vorhandensein einer sehr schwachen graphitic Scherbandes unterschiedlichen Stärke in und um der Reef. Der Reef, bei Obuasi, taucht im allgemeinen steil ab und geöffnete Aufstemmung ist die überwiegende gewinnenmethode. Die Stabilität der Wand begrenz die Stope grösse. Verschiedene Wahlen für das Erlauben der größeren Stopes für höhere Produktivität und das Begrenzen von Erzesverdünnung werden analysiert. Die ökonomischste Weise soll die Wände mit systematischen Kableankerbolzenunterstützungen verstärken. Diese Wahl addiert nicht nur die Kosten der Unterstützung aber erfordert auch zusätzliche Kosten fuer Zugangsentwicklung. Diese kontroversen Anforderungen werden fortwährend an der Grube analysiert um die Verdünnungkontrolle zu optimieren.

Jan 1, 2003