Search Documents

By M. Le Roux

Fine coal (-500 µm) is notoriously difficult to dewater. It is not uncommon for a dewatered product to have a moisture content as high as 30 per cent after vacuum filtration. This poses several handling and financial problems to such an extent that a lot of fine coal is discarded onto slurry waste ponds. A novel way of dewatering fine coal was developed at North-West University. It entails deliberately damaging the filter cake during dewatering to allow for an increased flow of air through the cake at the expense of the applied pressure differential. This method resulted in an average improvement in final cake moisture of between 3 per cent and 5 percent when executed in the laboratory under controlled conditions. A device was designed that could be fitted onto existing belt filters that would damage the filter cake as it passes by. This device was tested on a vacuum belt filter installation at a coal beneficiation operation in the Waterberg coal field in South Africa. The results showed a 3 per cent reduction in final moisture of the cake, proving the validity of the method at full industrial scale.

Jan 1, 2012

By J. H. Potgieter

This paper describes an investigation to separate and selectively recover silver, gold and platinum from jewellery and laboratory wastes, and produce technical grade material suitable for training purposes. Nitric acid was employed to dissolve and separate silver and other impurities from gold and platinum, which were then dissolved in aqua regia and precipitated selectively. The current work quantified the effects of temperature, stirring rate, leaching agent concentration and solid: liquid ratio on the recovery of the various noble metals and in summary yielded the optimum treatment conditions in each case. It was found that increased leaching reagent concentration (in the case of Ag), temperatures and stirring rates enhanced the recovery kinetics and optimum yield of the three noble metals. An increased liquid to solid ratio also enhanced the recovery of the silver. Recovery yields 97.1%, 99.9%and 99.4% for silver, gold and platinum, respectively, were obtained. The recovered silver, gold and platinum had purities of, respectively, 98.3%, 99.1% and 99.0%. A cost saving of approximately R10 000 per kilogram of scrap refined could be achieved by the in-house treatment of the waste, not to mention the time-saving benefit.

Jan 1, 2004

By R. L. Lawson

I?ve been asked to appraise the global role of coal and mining, and the best place I can think of to begin is with the World watch Institute, which purports to monitor all things global. Last fall the institute?s magazine, entitled World Watch, in a cover story called for a worldwide campaign to outlaw the use of coal before this century?s end. To my mind the article began the campaign. However, the institute had to admit that no such ban will be possible unless there is special help and heavy intervention?that is, novel policies and punitive taxes. I?ll quote directly from the magazine to underscore the point: ?without them the market will continue to deceive us into thinking coal is cheap, abundant and irreplaceable?.

Jan 1, 2001

By Kathryn C. Sole, Owen Tinkler

"Although the first large-scale application of copper recovery by solvent extraction (SX) took place in Zambia in the early 1970s, it is only in the last decade that this technology has become widely employed in this part of the world and is now a mainstay unit operation in most copper hydrometallurgical flowsheets. The mineralogy of the ores in the African Copper Belt, and hence the characteristics of the African leach liquors, differ significantly from those in Chile and the south-western USA, where copper SX has had a long and successful history. These differences provide operators, metallurgists, reagent vendors and engineers with many challenges: new approaches are needed to adapt this technology for successful implementation in this region. This paper examines typical operating practice in the African Copper Belt, discusses differences compared with other parts of the world and looks at some of the challenges and opportunities presented by these flowsheets. INTRODUCTION Following the success of the Rancher’s Bluebird and Bagdad solvent extraction and electrowinning (SX–EW) operations in Arizona in the late 1960s, the Tailings Leach Plant at Chingola, Zambia became the first large-scale copper SX plant in the world, commissioned in 1974. Despite the equipment design now being outdated, this plant still continues to operate successfully, indicating the versatility and adaptability of this technology. Today, there are some 75 copper SX operations worldwide with cathode production above 10 kt/a. The top ten producers currently account for some 40% of the global 4.3 Mt/a SX–EW copper production. South America (predominantly Chile and Peru) is the largest copper cathode-producing region, with annual production of some 2 Mt. The Central African Copper Belt (Zambia and the Democratic Republic of Congo (DRC)) is second, with cathode production of 1.2 Mt/a and North America (USA and Mexico) third, producing close to 0.8 Mt/a Cu (Cytec data, 2014). The remaining 0.35 Mt/a comes from all other regions combined (referred to as “Rest-of-World”). Current and future operations in Zambia and the DRC are summarised in Figure 1. The industry in this region is characterised by a large number of small (3 to 20 kt/a) plants, mainly Chinese-owned, and a few very large (>200 kt/a) operations, owned by major multinational corporations. This paper examines typical operating practice in the African Copper Belt, discusses the differences compared with other parts of the world and looks at some of the challenges presented by the conditions, as well as innovations in flowsheets, reagents and operating conditions that have been introduced in these circuits."

Jan 1, 2015

By C. Kasatuka

Globalization creates investment opportunities for enterprises around the world. Attracting foreign investment has been a key challenge for economic growth in developing countries. Corruption, political instability, armed conflict, and other internal problems affect foreign direct investment (FDI) inflows negatively. A framework of criteria provides a basis for comparing non-commercial risk (NCR) among twenty-three mineral economies. Countries competing for foreign direct investment inflows are ranked from least to most risky. This study compares Inward FDI Performance Index (IND) with NCR ratings in developing countries and shows that risk is increasingly mitigated by means of appropriately structured insurance. Given the option for countries with similar mineral potential, investors will generally invest in the country that offers lower non-commercial risk. Keywords: foreign direct investment, non-commercial risk, developing countries.

Jan 1, 2006

By B. Salt, R. Sullivan, E. Roos, M. de Vries, K. McKenna, L. R. Nelson, M. J. N. Uys, P. Jacobs, E. Munnik, P. Lewarne

A review is presented of the furnace cooling system design and operating developments since the initial furnace start up in January 2001 of the Chambishi DC-arc furnace to produce ferrocobalt alloy. The furnace operating conditions present a number of challenges to the furnace designers and operators in particular to provide a sustainable lining that can withstand the highly corrosive siliceous slag (roughly 50% SiO2). This is exacerbated by the dual requirement to operate this slag in a relatively highly superheated state (?T ? 400°C when tapped at 1550°C) to ensure that the ferroalloy can be tapped (estimated 1370°C alloy liquidus temperature) prior to atomisation. The core design challenge occurs at the alloy-slag interface, where a single refractory type cannot simultaneously meet the dual requirement of both adequate alloy and slag corrosion compatibility. Progression by the fourth furnace campaign to involve a retrofit of the bath sidewall to Hatch high-intensity, water-cooled, copper Waffle coolers and tapblocks is described. This involves operation of the entire slag bath, the slag-alloy interface and a portion of the alloy within a more chemically compatible refractory/slag (and possibly at times even an alloy) freeze-lining. Due to the high furnace power density employed (up to 500 kW/m2 hearth area) coupled with the large slag superheat needed, the resulting imposed peak bath sidewall heat fluxes are substantial, especially in the alloy (typically averaging 170 kW/m2), and on occasion have exceeded 1000 kW/m2. The performance of the Hatch Copper Waffle coolers under such aggressive process pyrometallurgical conditions is described. Aspects of the design and especially operating strategies to effect sustained production at up to 38 MW power input are also discussed.

Jan 1, 2004

By C. F. Strydom

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The Self-directed work team concept is the product of relentless performance pressure on American industries during the late eighties and early nineties from other world industrial leaders like Japan. The concept proved to be a successful vehicle by which the Americans could increase their production and improve their safety statistics. The aim of this study is to evaluate the concept as a means to improve the overall performance on South African goldmines. he study is directed by a historical research section, answering questions like: ?Why do we need to change? ?What is a Self-directed work team? ?What are the principle advantages of the concept? ?What are the essential requirements for the concept to succeed? The study also includes an empirical research section that focuses on the current Self-directed work team situation in the South African gold mining industry. The empirical research section is limited to three case studies within Anglogold due to a study period of only six weeks. The mines chosen for the case studies have been labelled Mine 1, Mine 2 and Mine 3. The latter being the base mine allowing for a more in depth study. This includes a perception analysis towards Self-directed work teams within the mine. The study proves the truth of the Latin proverb ?Tempora mutantur, nos et mutamur in illis? meaning ?The times are changing, and we are changing with them?. The chief change catalysts identified are a dwindling gold price and a projected labour crisis. From the study it is evident that the Self-directed work team concept disposes of the critical parameters required for a dramatic improvement in performance. The study also indicates that for the concept to succeed, certain factors like top-level commitment and management-employee trust have to be in place. Sadly, the concluding part of the study proves that very few of the identified critical success parameters are present in the South African gold mining industry. This can serve to explain why the industry only has success with the concept when monetary gain is the chief motivator. The study only focuses on the reasons why the concept is not performing to its full potential and does not wander into explaining the reasons for the current unsupportive milieu in the industry. Self-directed work teams could well rescue the South Africangold mining industry but currently we are driving a square pin into a round hole! [Terminology SDWT?Self-directed work teams AEL?Adventure Experiential Learning ISW?In-stope worker POLC?Plan, organize, lead and control TEC?Total employee costed Silo?The confinement of departments preventing networking JCI?Johannesburg Consolidated Investment Co. Ltd]

Jan 1, 2002

By Merete Tangstad, Kai Tang

The primary aim of the present investigation is to develop a model which permits to calculate/predict the viscosities of ferromanganese slags, typically focus on the MnO-SiO2-Al2O3-CaO-MgO-FeO multicomponent system. The present viscosity model emphasizes the ability of prediction, i.e. using the binary parameters to extrapolate the viscosities in ternary and higher order systems. To this end, a physical sound model is essential. Temperature dependence of viscosity is described by the Eyring?s formalism. The well-known cell model is used to define the SiO44- tetrahedra in the silicate melts. Composition dependence is expressed in term of viscous activation energy, which is characterized by the binary structural units. The viscosities in ternary and higher order systems are hence predicted using the binary activation parameters. The model has been used to calculate the viscosities in the whole liquid composition range of ferromanganese slag.

Jan 1, 2007

By W. Biermann

All industrial processes are economically driven, resulting in the ever increasing need for process optimization in order to stay competitive and profitable. Numerous models has been published depicting the optimization of the raw material usage in an arc furnace, as well as the thermal and electrical efficiency; however, to obtain a holistic view of the cost-effectiveness of the process one needs to expand the model to include the cost of all the operational variables. This project therefore aimed to not only include the raw material feeds and power consumption as input variables, but also the labour, maintenance, and environmental costs to generate an all-inclusive financial balance. In the end, the model was able to mathematically optimize the ferrochrome (FeCr) production process through evaluating the effect of a specified combination of input parameters. It could therefore be used as a tool to aid in managerial decision-making; to appraise and correspondingly adjust certain operational variables in order to achieve a maximum return on investment. This paper fully describes the reasoning behind the choice of the essential model components, the assumptions made during the models development, the calculation approach, as well as the advantages, limitations, possible applications, and areas for expansion of the final model. Through running simulations with plant data, it was found that the accuracy of final model remained fairly constant when applied to stable furnace conditions, but was met with a number of limitations when applied to more complex situations. These limitations could, however, be overcome through further development and expansion of the existing model to include a larger number of process variables.

Jan 1, 2012

By A. Bhattacherjee

The Shewhart [X]?and R charts are still the most popular control charts in use today for continuous monitoring of quality data. However, for these charts to function properly, the underlying assumption of normality and independence of data must be satisfied. When either independence and/or normality of data are not present, which is a common feature of ore quality data, an application of the conventional Shewhart [X]?and R charts may introduce false alarms in the analysis of the data. To address these issues, a guideline is proposed for construction of appropriate univariate and multivariate control charts for a variety of situations. A use of this guideline to a bauxite mine suggested the construction of special cause control chart for the analysis of individual variables namely, Al2O3% and SiO2%; whereas, the multivariate T2 chart based on residuals is proposed for the bivariate analysis of the variables. The case study clearly revealed that without considering the data correlation, one may be in a state of false impression about an out of control condition while using the Shewhart [X]?and R charts for univariate and the Hotelling T2chart for multivariate analysis. To compare the effectiveness of the control charts, specifically the Shewhart [X]?and the special cause control charts, a simulation study was conducted. It was found that the conventional Shewhart chart provided lower probability of coverage than the special cause control chart. It was also revealed that the quality specification of Al2O3% is met as the variation of Al2O3% is well within the specification limits; whereas, it is difficult to meet the quality specification of SiO2% on a regular basis.

Jan 1, 2002

By A. W. Breed

The bioleaching of arsenopyrite, the oxidation of arsenate and the precipitation of ferric arsenate are competing reactions, hence their rates depend on the relative concentrations of the respective species, and the activity of the bacterial culture. Bacterial arsenic resistance may be attributed to the Pst+Pit-mutation and an energy dependent efflux pump. Pst+Pit-mutations result in a reduced uptake of arsenate. This enables the bacteria to survive in solutions in which the arsenate concentration is significantly higher than the arsenite concentration. However, the excretion of arsenate requires energy. Therefore, in the absence of an energy source or during periods of reduced bacterial activity, the inhibitory effect of arsenate may manifest at concentrations to which the culture has been adapted. The chemical ferric leaching rate of pyrite and arsenopyrite decrease with a decrease in the solution redox and may be described using a modified Butler-Volmer equation. The bacterial ferrous-iron oxidation kinetics of L. ferrooxidans also depend on the redox potential, and can be described using a Michaelis-Mententype model modified to account for both temperature and pH. A model developed using the independently determined ferric leaching, and ferrous-iron oxidizing kinetics, has been shown to compare well with the experimental data for the continuous bioleaching of pyrite. Keywords: Leptospirillum ferrooxidans, arsenopyrite, bioleaching, sulphide minerals ferrous-iron oxidation kinetics, ferric leaching kinetics, redox potential

Jan 1, 2000

By T. Chikande

"Falls of ground pose costly hazards to personnel and equipment and thus measures should be taken to prevent them. This study endeavours to improve the support systems used in geotechnically poor ground at a Zimbabwean platinum mine by analysing the status quo and recommending an effective support system. Various techniques were used to determine the quality of ground conditions, predict the rock mass behaviour, and to identify the appropriate rockbolt type. An analysis of the current ground control methods and their limitations was also undertaken.The results showed that the current support system and mining practices in poor ground need to be modified to improve safety and productivity. Stoping overbreak is influenced by poor ground conditions and the explosives currently used. The use of emulsion is recommended to replace ANFO. Redesigning of pillars is also recommended in poor ground conditions. An evaluation of the current roofbolt system indicated an opportunity for improvement. With new insight on the performance of the shorter length roofbolts currently in use, a new support system was recommended taking into consideration cost-benefit analysis. Barring down using pinch bars in poor ground was seen as a risky and time-consuming exercise, hence the use of mechanical scalers is recommended to achieve zero harm and to meet production targets. Smoothwall blasting is recommended in poor ground to minimize excavation damage. Other recommendations include the use of hydrological surveys to determine groundwater levels and implement corrective measures. Both empirical and numerical modelling approaches need to be utilized in determining the optimum support. IntroductionThe presence of geological discontinuities such as faults and joints weakens the rock mass. Adequate support is critical in achieving zero harm in underground mines. This paper reviews the current support systems used in poor ground conditions at a Zimbabwean platinum mine. The area of research is located on the Great Dyke of Zimbabwe. The mine exploits platinum group elements (PGEs) and base metals. It is shallow, having a maximum depth of less than 300 m. The Great Dyke is the second largest reserve of PGEs, following the South African Bushveld Complex (Oberthur et al., 2012). It is a linear layered intrusion that extends for about 550 km with a maximum width of 11 km (Prendergast, 1989). The generalized section of the Great Dyke is almost like a trumpet, comprising layers that dip towards the centre. The reef exploited at the mine, the Mineralised Sulphide Zone (MSZ), is located in the pyroxenite layer, which is hosted in the ultramafic sequence. The MSZ is a uniform layer about 2– 3.5 m thick, dipping at around 10–14° from surface outcrop towards the axis of the basin, and located between bronzite and websterite horizons. The visible disseminated sulphide mineralization shows a typical and consistent vertical distribution of platinum group metal (PGM) and base metal values. The research was undertaken to review the current support systems used in geotechnically poor ground conditions in a bid to improve both safety and productivity."

Jan 1, 2016

By J. Autio, H. Malmlund

The excavation damage zone (EDZ) caused by drill and blast excavation consists of intense damage adjacent to the remaining half barrel of the blast hole, new fracturing induced by the blast and reactivation of pre-existing fractures. The properties of intense microfracturing adjacent to the half barrels of remaining blast holes are based on study of rock samples from ZEDEX-tunnel and it’s extension at Äspö and the Research tunnel at Olkiluoto in Finland. The new and reactivated fracturing is based on results of mapping of slots cut in the rock in ZEDEX-project. The zone of increased porosity adjacent to half barrels, which penetrates to a depth of some centimeters was studied by using novel 14C-PMMA method. The penetration of the radial fractures, which is an order of magnitude deeper, was studied by mapping using color penetrant. Results of EDZ studies carried out at Äspö HRL in Sweden and in Research Tunnel at Olkiluoto show that the properties of EDZ can be affected significantly by engineering design. The result imply that the additional pore volume caused by distinct fracturing around the blast holes caused by state-of-the-art smooth blasting technique could be of the same order as that of the damaged zone adjacent to the surface of the half barrels. Durch Bohr- und Sprengarbeiten entstandene Eigenschaften der Auflockerungszone: Die durch Bohr- und Sprengarbeiten entstandene Auflockerungszone besteht aus einem großen, an das Resthalbrohr des Bohrloches angrenzenden Schaden, neuer Rissbildung und einer Reaktivierung der bereits existierenden Risse. Die Eigenschaften einer immensen, an die Halbrohre der Restbohrlöcher angrenzenden Mikrorissbildung beruhen auf einer Studie über die aus dem ZEDEX-Tunnel gewonnenen Gesteinsproben und deren Fortsetzung im Untertage-Labor Äspö (Hard Rock Laboratory, HRL) in Schweden und im Forschungstunnel bei Olkiluoto in Finnland. Die neue und reaktivierte Rissbildung basiert auf den Auswertungsergebnissen der Schlitze, die bei dem ZEDEX-Projekt ins Gestein geschnitten wurden. Die Zone der vermehrten, an die Halbrohre angrenzenden Porösität, die in ein paar Zentimeter Tiefe eindringt, wurde anhand der neuen 14C-PMMA-Methode untersucht. Das Eindringen der etwas tiefer gelegenen radialen Risse wurde anhand eines farbigen Eindringungsmittels untersucht. Die in Äspö und Olkiluoto durchgeführten EDZ-Studien zeigen, dass die EDZ-Eigenschaften wesentlich durch Engineering Design beeinflusst werden können. Das durch Bohrarbeiten verursachte Hohlraumvolumen der Rissbildung um den Tunnel herum ist ähnlich wie das Hohlraumvolumen der Bruchzone um die Bohrlöcher herum. Caractéristiques d’une zone endommagée par le creusement résultant d’un creusement par forage et dynamitage: La zone endommagée par le creusement résultant d’un creusement par forage et dynamitage présente un endommagement intense adjacent au demi-cylindre restant du trou de mine, une nouvelle fracturation et la réactivation des fractures préexistantes. Les caractéristiques de la microfracturation intense adjacente aux demi-cylindres des trous de mine restants reposent sur l’étude des échantillons de roche en provenance du tunnel ZEDEX et de son extension au laboratoire souterrain d’Äspö (« Hard Rock Laboratory » ou HRL) en Suède et du tunnel de recherche d’Olkiluoto en Finlande. La fracturation nouvelle et réactivée repose sur les résultats du placement des rainures sur la roche dans le projet ZEDEX. La zone de porosité accrue adjacente aux demi-cylindres et pénétrant à une profondeur de quelques centimètres à fait l’objet d’études recourant à la nouvelle méthode 14C-PMMA. La pénétration des fractures radiales, considérablement plus profondes, a été étudiée par placement en utilisant un agent pénétrant coloré. Les résultats des études EDZ effectuées à Äspö et à Olkiluoto montrent que les caractéristiques de l’EDZ sont susceptibles d’être affectées de manière significative par la conception technique. Le volume vide de fracturation résultant du dynamitage autour du tunnel est du même ordre que celui de la zone concassée autour des trous de mine.service.

Jan 1, 2003

By S. M. Rupprecht

Transportation accounts for some 26% of all mine accidents in South Africa. Although this figure may not be as prolific as fall of grounds accidents or accidents caused by seismic events, the enormity of transportation accidents demands attention, especially as many of these accidents are avoidable. This paper investigates vertical (i.e. shaft), horizontal (i.e. haulages), and in-stope transportation systems and their function as it applies to safety. Recent transportation accidents are discussed looking at current trends within the three transportation areas. In the shaft area, discussions will focus on handling of material cars, loading and off-loading of the workforce and management of shaft orepass systems. The horizontal component will focus on personnel transportation, safety around trains and hoppers, and handling of material in the cross-cut. The discussion on in-stope transportation will focus on the general congestion of the stope environment and how it affects the overall movement of personnel, material, and rock. Of concern are the large numbers of material handling and scraper winch accidents that occur and which will be discussed in some detail. The paper will conclude with a section on proposed guidelines within the three above-mentioned systems for mine engineers to consider in mine design and life of mine planning and scheduling. Keywords Underground logistics, safety in material handling.

Jan 1, 2011

By J A. Rabe, PAP Fouche, K O?Neill

Two of the most important issues mines have to deal with are tracking the ore mined from pit to plant and to test the efficiency of beneficiation equipment. Kumba Resources and Saco Systems are working together at moment to develop a RFID tracer system to help address these issues. This paper will focus on the tracking of ore from pit to plant. The main advantages for ore tracking is to ensure plant feed blending and dilution according to plan. The RFID tracer system works on the basis of a tracer that physically simulates the ore properties and radio frequency technology that facilitates communication with the tracer and allowing information to be stored on the tracer. This paper tends to indicate the progress on the application of RFID tracer technology in the minerals processing environment as tested at Kumba Resources so far. It is concluded that the system has great potential, but some important problems remain

Jan 1, 2005

By S. K. Murphy

A partial shaft pillar extraction project was embarked on at a mine in the West Wits mining region in South Africa. Prior to the extraction, a rock engineering assessment was conducted with the main objective being to establish which areas of the shaft pillar could be extracted without unduly affecting the stability of major infrastructure within the shaft pillar. Standard numerical modelling methods were used to conduct this assessment and several areas were identified for extraction. However, during the extraction process, it was found that the infrastructure was affected more than was originally predicted by linear elastic modelling. In addition to this, several large events resulted in far more large aftershocks than would normally be predicted. In order to gain an understanding of this phenomenon, seismic data was integrated with numerical modelling as follows: > The seismic data in the form of displacements was integrated in 3D space within the model to assess the effect of static stress changes associated with seismic activity > Data from large events was integrated onto specific structures, where displacements associated with large events were integrated onto the plane of structure in question. This paper describes the methodology and results obtained from each of the above processes and include insights into the mining process that were previously unfathomable using standard linear elastic numerical modelling. The way forward for this rock engineering assessment of partial shaft pillar extraction is also discussed.

Jan 1, 2012

By E. Yalçin

The data set often contains one or more secondary variables. These secondary variables are usually spatially cross correlated with the primary variable. The addition of the cross-correlated information reduces the variance of the estimation error by using the cokriging method. The grade estimation results of ordinary kriging and cokriging methods are evaluated and it was found that the estimation variance of cokriging method is slightly lower than ordinary kriging. The effect of variation of block dimension on the estimation results is also investigated and it was seen that the cokriging estimation variance values also decrease as the block dimension increases.

Jan 1, 2005

By K. C. Mills, R. Thackray

A test has been devised that can predict accurately the % crystallinity developed in a slag film formed between the steel strand and the mould. The % crystallinity in the test samples was determined and compared with that for slag films formed in the mould when casting with that flux. There was good agreement between the % crystallinity in the test samples and the slag films. It was found that additions of TiO2and ZrO2had little effect on the amount of crystalline phase formed, but additions of CaO caused a dramatic increase in the amount of crystalline phase formed. Various parameters (which can be calculated from chemical composition of the flux) have been plotted against % crystallinty in the test samples. It was found that the modified (NBO/T) ratio provided the best relation with % crystallinity for the various parameters tested. There commended relation is % crystallinity=141.1(NBO/T)-284.0. Keywords: continuous casting, mould flux, slag film, crystallinity, chemical composition

Jan 1, 2004

By J. M. Ortiz

This paper shows the usefulness of geostatistical conditional simulation combined with the quantification of sampling errors obtained from the analyses of fundamental errors ? validated from duplicate data ? to assess the relevance of the quality and quantity of the information, for short-term mine planning purposes. Traditional blast-hole drilling equipment has been designed for efficient drilling, but not for obtaining high-quality samples. Furthermore, blast-hole sampling interferes with production, and thus usually produces poor-quality results. These results are the basis of short-term plans, where the grades of selective mining units are estimated and used for distinguishing between ore and waste. Under these conditions, misclassification (ore blocks sent to the waste dump and waste blocks processed at the plant) is inevitable, leading to significant hidden losses that can amount to millions of dollars per annum. Reverse circulation drilling with the latest automated sampling technology improves significantly the quality of the information used for short-term planning, and thus reduces misclassification, improving the financial returns of the operation. In this paper, we present the general methodology for assessing the effect of poor blast-hole sampling, as compared to advanced reverse circulation drilling grids at several spacings, in order to arrive at the most appropriate grid for short-term planning. This plan can be prepared well in advance using several additional variables that are usually not available when the plan is based on blast-hole samples. Furthermore, blending options can be analysed in order to optimize plant recovery, minimize the use of sulphuric acid, etc. Three case studies are presented, namely a typical porphyry copper deposit, an exotic oxide copper deposit, and a complex gold deposit, where mineralization is controlled by structures and lithology. This paper shows that in all cases, advanced reverse circulation drilling grids provide good-quality information that, coupled with the use of geostatistics for short-term mine planning, significantly improve the financial returns of the operation.

Jan 1, 2014

By M. Tangstad, J. D. Steenkamp

In April 2013 a 48 MVA submerged arc furnace producing silicomanganese was excavated in South Africa. Since the high shell temperatures recorded in the tap-hole area resulted in the furnace being switched out for relining, the tap-hole area was excavated systematically. A refractory wear profile of the tap-hole area with affected hearth and sidewall refractory was obtained in elevation. The carbon ramming paste in front of, above, andbelow the tap-hole was worn, as was the SiC with which the tap-hole was built. A clay mushroom formed but was detached from the refractories. Thermodynamic and mass-transfer calculations were conducted to quantify the potential for wear by chemical reaction between refractory and slag and refractory and metal in the tap-hole area. It was found that chemical reaction between refractory and slag or metal could offer only a partial explanation for the wear observed; erosion is expected to contribute significantly to wear.

Jan 1, 2015